Fix a bitmask typo in the pdc202xx_new PLL frequency detection code
which causes it to truncate an intermediate difference to 26 bits
instead of the correct 30 bits (the PLL's bitwidth).
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Port of Alan's patch for pata_via.c.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Ensure that BLK_DEV_IDE is built-in before allowing BLK_DEV_IDE_PMAC to
be selected.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Bret Towe <magnade@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: Daniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method. In order to achieve that, do
the following changes:
- install the method for all chips, not only HPT36x/370 and improve the code
formatting by killing the extra tabs while at it;
- add to the end of the 'switch' statement in the method cases for HPT372[AN]
and HPT374 chips upon which the known SATA cards are based;
- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
behave correctly;
- move the HPT370[A] cases below the HPT36x case for consistency.
While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bob Ham <rah@bash.sh>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...
Bart: keep "findev" variable initialization to silence gcc
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE core never marked the PCI IDE devices as being in use after succesfull
driver probe call (the devices were marked in use only while being probed), and
so was susceptible to issues caused by unsolicited PCI hotplug device removal.
So, add pci_dev_get() call to ide_scan_pcidev() and convert this function to
the kernel style, also dropping a bunch of useless curly braces from its caller,
ide_scan_pcibus() and somewhat beautifying printk() call there, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently the mpc8xx ide driver will only work on arch/ppc so only
allow it to be built there. Also, killed a minor include that isn't
actually used by the driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: irq and pci_ids patch for Intel Tolapai
PCI: unhide SMBus on Compaq Deskpro EP 401963-001 motherboard
PCI: Remove __devinit from pcibios_get_irq_routing_table
PCI: remove devinit from pci_read_bridge_bases
PCI AER: fix warnings when PCIEAER=n
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: drivers/usb/serial/bus.c: Fix incompatible pointer type warning
USB: another quirky device (LCD display)
USB: fix serial gadget ACM breakage
USB: More USB_QUIRK_RESET_RESUME devices
USB Mass Storage: limit "Rockchip ROCK MP3" device (071b:3203) max I/O to 64 sectors per command
USB: Nikon D40 Quirks
USB: Add Sony Ericsson P1i to unusual_devs.h
USB: option: Add Dell HSDPA 5520 to driver
USB: option: Add a new device ID for the HUAWEI E220 HSDPA modem.
USB: fix linked list insertion bugfix for usb core
USB: quirky flash drive
USB: prevent Genesys USB-IDE from autosuspending
USB: prevent Thomson card reader from autosuspending
USB: Add iPhone device id to the quirk list.
USB: ftdi_sio: add of a new product/manufacturer, TML
usb/misc/sisusbvga: add product ID of TARGUS/MCT device
USB: oti6858: Remove broken ioctl code in -mm tree and also the broken fixes
This patch fixes a bug in AT91 mmc host driver, that enables the wakeup
from suspend on card detection pin even if the card detect pin is not
available (==0). If not card detection pin is defined, IRQ0 == FIQ gets
enabled and if some activity is present on that pin, the system gets a
FIQ request, that causes a crash.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
drivers/usb/serial/bus.c: In function usb_serial_bus_deregister:
drivers/usb/serial/bus.c:185:
warning: passing argument 1 of free_dynids from incompatible pointer type
Above build warning comes when CONFIG_HOTPLUG=n because argument of
free_dynids() in serial/bus.c is a struct usb_serial_driver, not a
struct usb_driver. This is not a runtime bug, because the function
is an empty stub and never dereferences the passed pointer anyway.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Two of the CDC ACM control requests in the serial gadget have never
been correct, and have been reported to cause serious troubles ... as
in, soft lockup and maybe watchdog reset (depending on hardware).
This patch makes those request fail cleanly, rather than misbehaving.
Someone using CDC ACM should fix them according to the FIXME comments
which now replace the previous bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like have the attached patch added to Linux kernel. The three
usb flash memories listed in the patch are being used in Intel's
ClassmatePC and need USB_QUIRK_RESET_RESUME to work reliably when
resuming from ram.
The MP3/MP4/AVI player "Rockchip ROCK MP3" is seen as a USB disk, but fails
if more than 128 sectors (64kB) are sent or requested in a single read or write
command, and disconnects from the USB bus.
Typical kernel log showing the problem is:
usb 3-1: reset high speed USB device using ehci_hcd and address 6
usb 3-1: reset high speed USB device using ehci_hcd and address 6
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
usb 3-1: USB disconnect, address 6
This patch works around the device limitation by adding "Rockchip ROCK MP3"
to unusual USB devices list and limiting data transfers to 64 sectors (32kB)
per command.
Tested on 2.6.23-rc5 (amd64).
Signed-off-by: Massimiliano Ghilardi <massimiliano.ghilardi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The D40 needs the same quirks as the other (semi-)professional Nikon cameras.
The patch is against 2.6.23-rc5.
Details:
http://bugs.gentoo.org/show_bug.cgi?id=191431
From: Ortwin Glück <odi@odi.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is based on information sent in by Christian Gothe.
Cc: Christian Gothe <christian.gothe@kapelan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the order of list_add_tail() arguments in
usb_store_new_id() so the list can have more than one single element.
Signed-off-by: Nathael Pajani <nathael.pajani@cpe.fr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
That drive is quite odd. It has 2K sectors, times out getting string
descriptors and needs a quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as986) prevents the troublesome Genesys USB-IDE adapter
from autosuspending. It may not be necessary for all such devices,
but the one in Bugzilla #8892 sometimes fails to resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as985) prevents the SGS THomson Microelectronics 4in1 card
reader from autosuspending. This resolves Bugzilla #8885.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added to a new product based on the FTDI 232R USB/Serial
transceiver, which is commercialized by The Mobility Lab. Here is a
trivial patch enclosed, against 2.6.22.6 kernel.
Signed-off-by: Pierre Castella <pp.castella@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device is Targus ACP50US which includes a Magic Control Technologies
usb vga device using the SiS315(E) or compatible.
Signed-off-by: Samson Yeung <fragmede@onepatchdown.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This stuff is simply not needed.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[INET_DIAG]: Fix oops in netlink_rcv_skb
[IPv6]: Fix NULL pointer dereference in ip6_flush_pending_frames
[NETFILTER]: Fix/improve deadlock condition on module removal netfilter
[NETFILTER]: nf_conntrack_ipv4: fix "Frag of proto ..." messages
[NET] DOC: Update networking/multiqueue.txt with correct information.
[IPV6]: Freeing alive inet6 address
[DECNET]: Fix interface address listing regression.
[IPV4] devinet: show all addresses assigned to interface
[NET]: Do not dereference iov if length is zero
[TG3]: Workaround MSI bug on 5714/5780.
[Bluetooth] Fix parameter list for event filter command
[Bluetooth] Update security filter for Bluetooth 2.1
[Bluetooth] Add compat handling for timestamp structure
[Bluetooth] Add missing stat.byte_rx counter modification
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] libiscsi: sync up iscsi and scsi eh's access to the connection
[SCSI] libiscsi: fix null ptr regression when aborting a command with data to transfer
[SCSI] qla2xxx: Update version number to 8.02.00-k3.
[SCSI] qla2xxx: Correct mailbox register dump for FWI2 capable ISPs.
[SCSI] qla2xxx: Correct 8GB iIDMA support.
[SCSI] qla2xxx: Correct management-server login-state synchronization issue.
[SCSI] qla2xxx: Don't modify parity bits during ISP25XX restart.
[SCSI] qla2xxx: Allocate enough space for the full PCI descriptor.
[SCSI] zfcp: fix the data buffer accessor patch
[SCSI] zfcp: allocate gid_pn_data objects from gid_pn_cache
[SCSI] zfcp: fix memory leak
This patch adds the Intel Tolapai LPC and SMBus Controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI quirk to unhide SMBus on Compaq Deskpro EP 401963-001 (PCA# 010174) motherboard.
Signed-off-by: Greg White <gw.kernel@tnode.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pcibios_get_irq_routing_table is an exported symbol. This results in a
modpost warning:
WARNING: vmlinux.o(.text+0xdca51): Section mismatch: reference to .init.text:pcibios_fixup_bus (between 'pci_scan_child_bus' and 'pci_scan_bus_parented')
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On MIPS with PCI && !HOTPLUG, I'm currently getting the following modpost
warning:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0x1ce128): Section mismatch: reference to .init.text:pci_read_bridge_bases (between 'pcibios_fixup_bus' and 'pcibios_enable_device')
On MIPS I have the call chains pci_scan_child_bus -> pcibios_fixup_bus ->
pci_read_bridge_bases. pci_scan_child_bus can't be __devinit because it
it is an exported symbol, thus pcibios_fixup_bus and pci_read_bridge_bases
can't be either.
For some reason I don't see this issue on x86; I blame compiler differences.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix warnings when CONFIG_PCIEAER=n:
drivers/pci/pcie/portdrv_pci.c:105: warning: statement with no effect
drivers/pci/pcie/portdrv_pci.c:226: warning: statement with no effect
drivers/scsi/arcmsr/arcmsr_hba.c:352: warning: statement with no effect
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of skbs in sk->write_queue do not have skb->dst because
we do not fill skb->dst when we allocate new skb in append_data().
BTW, I think we may not need to (or we should not) increment some stats
when using corking; if 100 sendmsg() (with MSG_MORE) result in 2 packets,
how many should we increment?
If 100, we should set skb->dst for every queued skbs.
If 1 (or 2 (*)), we increment the stats for the first queued skb and
we should just skip incrementing OutDiscards for the rest of queued skbs,
adn we should also impelement this semantics in other places;
e.g., we should increment other stats just once, not 100 times.
*: depends on the place we are discarding the datagram.
I guess should just increment by 1 (or 2).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
So I've had a deadlock reported to me. I've found that the sequence of
events goes like this:
1) process A (modprobe) runs to remove ip_tables.ko
2) process B (iptables-restore) runs and calls setsockopt on a netfilter socket,
increasing the ip_tables socket_ops use count
3) process A acquires a file lock on the file ip_tables.ko, calls remove_module
in the kernel, which in turn executes the ip_tables module cleanup routine,
which calls nf_unregister_sockopt
4) nf_unregister_sockopt, seeing that the use count is non-zero, puts the
calling process into uninterruptible sleep, expecting the process using the
socket option code to wake it up when it exits the kernel
4) the user of the socket option code (process B) in do_ipt_get_ctl, calls
ipt_find_table_lock, which in this case calls request_module to load
ip_tables_nat.ko
5) request_module forks a copy of modprobe (process C) to load the module and
blocks until modprobe exits.
6) Process C. forked by request_module process the dependencies of
ip_tables_nat.ko, of which ip_tables.ko is one.
7) Process C attempts to lock the request module and all its dependencies, it
blocks when it attempts to lock ip_tables.ko (which was previously locked in
step 3)
Theres not really any great permanent solution to this that I can see, but I've
developed a two part solution that corrects the problem
Part 1) Modifies the nf_sockopt registration code so that, instead of using a
use counter internal to the nf_sockopt_ops structure, we instead use a pointer
to the registering modules owner to do module reference counting when nf_sockopt
calls a modules set/get routine. This prevents the deadlock by preventing set 4
from happening.
Part 2) Enhances the modprobe utilty so that by default it preforms non-blocking
remove operations (the same way rmmod does), and add an option to explicity
request blocking operation. So if you select blocking operation in modprobe you
can still cause the above deadlock, but only if you explicity try (and since
root can do any old stupid thing it would like.... :) ).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're now using a generic tuple decoding function in ICMP
connection tracking, ipv4_get_l4proto() might get called with a
fragmented packet from within an ICMP error. Remove the error
message we used to print when this happens.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated the multiqueue.txt document to call out the correct kernel
options to select to enable multiqueue.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Denis V. Lunev <den@openvz.org>
addrconf_dad_failure calls addrconf_dad_stop which takes referenced address
and drops the count. So, in6_ifa_put perrformed at out: is extra. This
results in message: "Freeing alive inet6 address" and not released dst entries.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Alexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all are listed, same as the IPV4 devinet bug.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: http://bugzilla.kernel.org/show_bug.cgi?id=8876
Not all ips are shown by "ip addr show" command when IPs number assigned to an
interface is more than 60-80 (in fact it depends on broadcast/label etc
presence on each address).
Steps to reproduce:
It's terribly simple to reproduce:
# for i in $(seq 1 100); do ip ad add 10.0.$i.1/24 dev eth10 ; done
# ip addr show
this will _not_ show all IPs.
Looks like the problem is in netlink/ipv4 message processing.
This is fix from bug submitter, it looks correct.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When msg_iovlen is zero we shouldn't try to dereference
msg_iov. Right now the only thing that tries to do so
is skb_copy_and_csum_datagram_iovec. Since the total
length should also be zero if msg_iovlen is zero, it's
sufficient to check the total length there and simply
return if it's zero.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A hardware bug was revealed after a recent PCI MSI patch was made to
always disable legacy INTX when enabling MSI. The 5714/5780 chips
will not generate MSI when INTX is disabled, causing MSI failure
messages to be reported, and another patch was made to workaround the
problem by disabling MSI on ServerWorks HT1000 bridge chips commonly
found with the 5714.
We workaround this chip bug by enabling INTX after we enable MSI and
after we resume from suspend.
Update version to 3.81.
This problem was discovered by David Miller.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
