[ Upstream commit 4d6ec3a793 ]
The driver calls mfd_add_devices() but fails to call mfd_remove_devices()
in error paths after successful MFD device registration and in the remove
function. This leads to resource leaks where MFD child devices are not
properly unregistered.
Replace mfd_add_devices with devm_mfd_add_devices to automatically
manage the device resources.
Fixes: c96e976d9a ("net: wan: framer: Add support for the Lantiq PEF2256 framer")
Suggested-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Link: https://patch.msgid.link/20251105034716.662-1-vulab@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8a7ed9586 ]
The MLX5E_SHAMPO_WQ_HEADER_PER_PAGE and
MLX5E_SHAMPO_LOG_MAX_HEADER_ENTRY_SIZE macros are used directly in
several places under the assumption that there will always be more
headers per WQE than headers per page. However, this assumption doesn't
hold for 64K page sizes and higher MTUs (> 4K). This can be first
observed during header page allocation: ksm_entries will become 0 during
alignment to MLX5E_SHAMPO_WQ_HEADER_PER_PAGE.
This patch introduces 2 additional members to the mlx5e_shampo_hd struct
which are meant to be used instead of the macrose mentioned above.
When the number of headers per WQE goes below
MLX5E_SHAMPO_WQ_HEADER_PER_PAGE, clamp the number of headers per
page and expand the header size accordingly so that the headers
for one WQE cover a full page.
All the formulas are adapted to use these two new members.
Fixes: 945ca432bf ("net/mlx5e: SHAMPO, Drop info array")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1762238915-1027590-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bacd8d8018 ]
mlx5e_hw_gro_skb_has_enough_space() uses a formula to check if there is
enough space in the skb frags to store more data. This formula is
incorrect for 64K page sizes and it triggers early GRO session
termination because the first fragment will blow up beyond
GRO_LEGACY_MAX_SIZE.
This patch adds a special case for page sizes >= GRO_LEGACY_MAX_SIZE
(64K) which uses the skb->len instead. Within this context,
the check is safe from fragment overflow because the hardware
will continuously fill the data up to the reservation size of 64K
and the driver will coalesce all data from the same page to the same
fragment. This means that the data will span one fragment or at most
two for such a large page size.
It is expected that the if statement will be optimized out as the
check is done with constants.
Fixes: 92552d3abd ("net/mlx5e: HW_GRO cqe handler implementation")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1762238915-1027590-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 665a7e13c2 ]
HW-GRO is broken on mlx5 for 64K page sizes. The patch in the fixes tag
didn't take into account larger page sizes when doing an align down
of max_ksm_entries. For 64K page size, max_ksm_entries is 0 which will skip
mapping header pages via WQE UMR. This breaks header-data split
and will result in the following syndrome:
mlx5_core 0000:00:08.0 eth2: Error cqe on cqn 0x4c9, ci 0x0, qn 0x1133, opcode 0xe, syndrome 0x4, vendor syndrome 0x32
00000000: 00 00 00 00 04 4a 00 00 00 00 00 00 20 00 93 32
00000010: 55 00 00 00 fb cc 00 00 00 00 00 00 07 18 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4a
00000030: 00 00 3b c7 93 01 32 04 00 00 00 00 00 00 bf e0
mlx5_core 0000:00:08.0 eth2: ERR CQE on RQ: 0x1133
Furthermore, the function that fills in WQE UMRs for the headers
(mlx5e_build_shampo_hd_umr()) only supports mapping page sizes that
fit in a single UMR WQE.
This patch goes back to the old non-aligned max_ksm_entries value and it
changes mlx5e_build_shampo_hd_umr() to support mapping a large page over
multiple UMR WQEs.
This means that mlx5e_build_shampo_hd_umr() can now leave a page only
partially mapped. The caller, mlx5e_alloc_rx_hd_mpwqe(), ensures that
there are enough UMR WQEs to cover complete pages by working on
ksm_entries that are multiples of MLX5E_SHAMPO_WQ_HEADER_PER_PAGE.
Fixes: 8a0ee54027 ("net/mlx5e: SHAMPO, Simplify UMR allocation for headers")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1762238915-1027590-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae4789affd ]
The ICSSG driver does the initial FDB configuration which
includes setting the control registers. Other run time
management like learning is managed by the PRU's. The default
FDB hash size used by the firmware is 512 slots, which is
currently missing in the current driver. Update the driver
FDB config to include FDB hash size as well.
Please refer trm [1] 6.4.14.12.17 section on how the FDB config
register gets configured. From the table 6-1404, there is a reset
field for FDB_HAS_SIZE which is 4, meaning 1024 slots. Currently
the driver is not updating this reset value from 4(1024 slots) to
3(512 slots). This patch fixes this by updating the reset value
to 512 slots.
[1]: https://www.ti.com/lit/pdf/spruim2
Fixes: abd5576b9c ("net: ti: icssg-prueth: Add support for ICSSG switch firmware")
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251104104415.3110537-1-m-malladi@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fd5367391 ]
->nr_pages is int, it needs type extension before calculating the region
size.
Fixes: a90558b36c ("io_uring/memmap: helper for pinning region pages")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
[axboe: style fixup]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c74619e760 ]
hwsim radios marked destroy_on_close are removed when the Netlink socket
that created them is closed. As the portid is not unique across network
namespaces, closing a socket in one namespace may remove radios in another
if it has the destroy_on_close flag set.
Instead of matching the network namespace, match the netgroup of the radio
to limit radio removal to those that have been created by the closing
Netlink socket. The netgroup of a radio identifies the network namespace
it was created in, and matching on it removes a destroy_on_close radio
even if it has been moved to another namespace.
Fixes: 100cb9ff40 ("mac80211_hwsim: Allow managing radios from non-initial namespaces")
Signed-off-by: Martin Willi <martin@strongswan.org>
Link: https://patch.msgid.link/20251103082436.30483-1-martin@strongswan.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 327c20c21d ]
Fix a AA deadlock in refill_skbs() where memory allocation while holding
skb_pool->lock can trigger a recursive lock acquisition attempt.
The deadlock scenario occurs when the system is under severe memory
pressure:
1. refill_skbs() acquires skb_pool->lock (spinlock)
2. alloc_skb() is called while holding the lock
3. Memory allocator fails and calls slab_out_of_memory()
4. This triggers printk() for the OOM warning
5. The console output path calls netpoll_send_udp()
6. netpoll_send_udp() attempts to acquire the same skb_pool->lock
7. Deadlock: the lock is already held by the same CPU
Call stack:
refill_skbs()
spin_lock_irqsave(&skb_pool->lock) <- lock acquired
__alloc_skb()
kmem_cache_alloc_node_noprof()
slab_out_of_memory()
printk()
console_flush_all()
netpoll_send_udp()
skb_dequeue()
spin_lock_irqsave(&skb_pool->lock) <- deadlock attempt
This bug was exposed by commit 248f6571fd ("netpoll: Optimize skb
refilling on critical path") which removed refill_skbs() from the
critical path (where nested printk was being deferred), letting nested
printk being called from inside refill_skbs()
Refactor refill_skbs() to never allocate memory while holding
the spinlock.
Another possible solution to fix this problem is protecting the
refill_skbs() from nested printks, basically calling
printk_deferred_{enter,exit}() in refill_skbs(), then, any nested
pr_warn() would be deferred.
I prefer this approach, given I _think_ it might be a good idea to move
the alloc_skb() from GFP_ATOMIC to GFP_KERNEL in the future, so, having
the alloc_skb() outside of the lock will be necessary step.
There is a possible TOCTOU issue when checking for the pool length, and
queueing the new allocated skb, but, this is not an issue, given that
an extra SKB in the pool is harmless and it will be eventually used.
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: 248f6571fd ("netpoll: Optimize skb refilling on critical path")
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251103-fix_netpoll_aa-v4-1-4cfecdf6da7c@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5204943a4c ]
The existing code calls bnxt_cancel_reservations() after
bnxt_hwrm_func_drv_unrgtr() in bnxt_dl_reload_down().
bnxt_cancel_reservations() calls the FW and it will always fail since
the driver has already unregistered, triggering this warning:
bnxt_en 0000:0a:00.0 ens2np0: resc_qcaps failed
Fix it by calling bnxt_clear_reservations() which will skip the
unnecessary FW call since we have unregistered.
Fixes: 228ea8c187 ("bnxt_en: implement devlink dev reload driver_reinit")
Reviewed-by: Mohammad Shuab Siddique <mohammad-shuab.siddique@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shantiprasad Shettar <shantiprasad.shettar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28d9a84ef0 ]
While populating firmware host logging segments for the coredump, it is
possible for the FW command that flushes the segment to fail. When that
happens, the existing code will not update the max entry and entry size
in the segment header and this causes software that decodes the coredump
to skip the segment.
The segment most likely has already collected some DMA data, so always
update these 2 segment fields in the header to allow the decoder to
decode any data in the segment.
Fixes: 3c2179e663 ("bnxt_en: Add FW trace coredump segments to the coredump")
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-5-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff02be05f7 ]
With older FW, we may get the ASYNC_EVENT_CMPL_EVENT_ID_DBG_BUF_PRODUCER
for FW trace data type that has not been initialized. This will result
in a crash in bnxt_bs_trace_type_wrap(). Add a guard to check for a
valid magic_byte pointer before proceeding.
Fixes: 84fcd9449f ("bnxt_en: Manage the FW trace context memory")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Gautam R A <gautam-r.a@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deb8eb3916 ]
In bnxt_ptp_init(), when ptp_clock_register() fails, the driver is
not freeing the memory allocated for ptp_info->pin_config. Fix it
to unconditionally free ptp_info->pin_config in bnxt_ptp_free().
Fixes: caf3eedbcd ("bnxt_en: 1PPS support for 5750X family chips")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc7208ca80 ]
The netif_close() call in bnxt_shutdown() only stops packet DMA. There
may be FW DMA for trace logging (recently added) that will continue. If
we kexec to a new kernel, the DMA will corrupt memory in the new kernel.
Add bnxt_hwrm_func_drv_unrgtr() to unregister the driver from the FW.
This will stop the FW DMA. In case the call fails, call pcie_flr() to
reset the function and stop the DMA.
Fixes: 24d694aec1 ("bnxt_en: Allocate backing store memory for FW trace logs")
Reported-by: Jakub Kicinski <kicinski@meta.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251104005700.542174-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e120f46768 ]
Raw IP packets have no MAC header, leaving skb->mac_header uninitialized.
This can trigger kernel panics on ARM64 when xfrm or other subsystems
access the offset due to strict alignment checks.
Initialize the MAC header to prevent such crashes.
This can trigger kernel panics on ARM when running IPsec over the
qmimux0 interface.
Example trace:
Internal error: Oops: 000000009600004f [#1] SMP
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.34-gbe78e49cb433 #1
Hardware name: LS1028A RDB Board (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : xfrm_input+0xde8/0x1318
lr : xfrm_input+0x61c/0x1318
sp : ffff800080003b20
Call trace:
xfrm_input+0xde8/0x1318
xfrm6_rcv+0x38/0x44
xfrm6_esp_rcv+0x48/0xa8
ip6_protocol_deliver_rcu+0x94/0x4b0
ip6_input_finish+0x44/0x70
ip6_input+0x44/0xc0
ipv6_rcv+0x6c/0x114
__netif_receive_skb_one_core+0x5c/0x8c
__netif_receive_skb+0x18/0x60
process_backlog+0x78/0x17c
__napi_poll+0x38/0x180
net_rx_action+0x168/0x2f0
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Signed-off-by: Qendrim Maxhuni <qendrim.maxhuni@garderos.com>
Link: https://patch.msgid.link/20251029075744.105113-1-qendrim.maxhuni@garderos.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e25935ed2 ]
The devm_kcalloc() function never return error pointers, it returns NULL
on failure. Also delete the netdev_err() printk. These allocation
functions already have debug output built-in some the extra error message
is not required.
Fixes: efabce2901 ("octeontx2-pf: AF_XDP zero copy receive support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aQYKkrGA12REb2sj@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de0337d641 ]
The TSO path called ionic_tx_map_skb() before preparing the TCP pseudo
checksum (ionic_tx_tcp_[inner_]pseudo_csum()), which may perform
skb_cow_head() and might modifies bytes in the linear header area.
Mapping first and then mutating the header risks:
- Using a stale DMA address if skb_cow_head() relocates the head, and/or
- Device reading stale header bytes on weakly-ordered systems
(CPU writes after mapping are not guaranteed visible without an
explicit dma_sync_single_for_device()).
Reorder the TX path to perform all header mutations (including
skb_cow_head()) *before* DMA mapping. Mapping is now done only after the
skb layout and header contents are final. This removes the need for any
post-mapping dma_sync and prevents on-wire corruption observed under
VLAN+TSO load after repeated runs.
This change is purely an ordering fix; no functional behavior change
otherwise.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20251031155203.203031-2-mheib@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d261f5b09c ]
The TX path currently writes descriptors and then immediately writes to
the MMIO doorbell register to notify the NIC. On weakly ordered
architectures, descriptor writes may still be pending in CPU or DMA
write buffers when the doorbell is issued, leading to the device
fetching stale or incomplete descriptors.
Add a dma_wmb() in ionic_txq_post() to ensure all descriptor writes are
visible to the device before the doorbell MMIO write.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Mohammad Heib <mheib@redhat.com>
Link: https://patch.msgid.link/20251031155203.203031-1-mheib@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1fc201148 ]
Move address list traversal in inet_assoc_attr_size() under the sock
lock to avoid holding the RCU read lock.
Suggested-by: Xin Long <lucien.xin@gmail.com>
Fixes: 8f840e47f1 ("sctp: add the sctp_diag.c file")
Signed-off-by: Stefan Wiehler <stefan.wiehler@nokia.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20251028161506.3294376-4-stefan.wiehler@nokia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95aef86ab2 ]
For the following path not holding the sock lock,
sctp_diag_dump() -> sctp_for_each_endpoint() -> sctp_ep_dump()
make sure not to exceed bounds in case the address list has grown
between buffer allocation (time-of-check) and write (time-of-use).
Suggested-by: Kuniyuki Iwashima <kuniyu@google.com>
Fixes: 8f840e47f1 ("sctp: add the sctp_diag.c file")
Signed-off-by: Stefan Wiehler <stefan.wiehler@nokia.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20251028161506.3294376-3-stefan.wiehler@nokia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e57723fe53 ]
When iterating over the ARL table we stop at max ARL entries / 2, but
this is only valid if the chip actually returns 2 results at once. For
chips with only one result register we will stop before reaching the end
of the table if it is more than half full.
Fix this by only dividing the maximum results by two if we have a chip
with more than one result register (i.e. those with 4 ARL bins).
Fixes: cd169d799b ("net: dsa: b53: Bound check ARL searches")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251102100758.28352-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0be04b5fa6 ]
The switch clears the ARL_SRCH_STDN bit when the search is done, i.e. it
finished traversing the ARL table.
This means that there will be no valid result, so we should not attempt
to read and process any further entries.
We only ever check the validity of the entries for 4 ARL bin chips, and
only after having passed the first entry to the b53_fdb_copy().
This means that we always pass an invalid entry at the end to the
b53_fdb_copy(). b53_fdb_copy() does check the validity though before
passing on the entry, so it never gets passed on.
On < 4 ARL bin chips, we will even continue reading invalid entries
until we reach the result limit.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251102100758.28352-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c264294624 ]
In the New Control register bit 1 is either reserved, or has a different
function:
Out of Range Error Discard
When enabled, the ingress port discards any frames
if the Length field is between 1500 and 1536
(excluding 1500 and 1536) and with good CRC.
The actual bit for enabling IP multicast is bit 0, which was only
explicitly enabled for BCM5325 so far.
For older switch chips, this bit defaults to 0, so we want to enable it
as well, while newer switch chips default to 1, and their documentation
says "It is illegal to set this bit to zero."
So drop the wrong B53_IPMC_FWD_EN define, enable the IP multicast bit
also for other switch chips. While at it, rename it to (B53_)IP_MC as
that is how it is called in Broadcom code.
Fixes: 63cc54a6f0 ("net: dsa: b53: Fix egress flooding settings")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251102100758.28352-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e4ebdc160 ]
BCM63XX's switch does not support MDIO scanning of external phys, so its
MACs needs to be manually configured for autonegotiated link speeds.
So b53_force_port_config() and b53_force_link() accordingly also when
mode is MLO_AN_PHY for those ports.
Fixes lower speeds than 1000/full on rgmii ports 4 - 7.
This aligns the behaviour with the old bcm63xx_enetsw driver for those
ports.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251101132807.50419-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6a8a5477f ]
There is no guarantee that the port state override registers have their
default values, as not all switches support being reset via register or
have a reset GPIO.
So when forcing port config, we need to make sure to clear all fields,
which we currently do not do for the speed and flow control
configuration. This can cause flow control stay enabled, or in the case
of speed becoming an illegal value, e.g. configured for 1G (0x2), then
setting 100M (0x1), results in 0x3 which is invalid.
For PORT_OVERRIDE_SPEED_2000M we need to make sure to only clear it on
supported chips, as the bit can have different meanings on other chips,
e.g. for BCM5389 this controls scanning PHYs for link/speed
configuration.
Fixes: 5e004460f8 ("net: dsa: b53: Add helper to set link parameters")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251101132807.50419-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b526c2cf ]
The call to device_node_to_regmap() in airoha_mdio_probe() can return
an ERR_PTR() if regmap initialization fails. Currently, the driver
stores the pointer without validation, which could lead to a crash
if it is later dereferenced.
Add an IS_ERR() check and return the corresponding error code to make
the probe path more robust.
Fixes: 67e3ba9783 ("net: mdio: Add MDIO bus controller for Airoha AN7583")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251031161607.58581-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f6115ad88 ]
If the memory allocation in gpiolib_seq_start() fails, the s->private
field remains uninitialized and is later dereferenced without checking
in gpiolib_seq_stop(). Initialize s->private to NULL before calling
kzalloc() and check it before dereferencing it.
Fixes: e348544f79 ("gpio: protect the list of GPIO devices with SRCU")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20251103141132.53471-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5d527be7e ]
Looking up a GPIO controller by label that is the name of the software
node is wonky at best - the GPIO controller driver is free to set
a different label than the name of its firmware node. We're already being
passed a firmware node handle attached to the GPIO device to
swnode_get_gpio_device() so use it instead for a more precise lookup.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: e7f9ff5dc9 ("gpiolib: add support for software nodes")
Link: https://lore.kernel.org/r/20251103-reset-gpios-swnodes-v4-4-6461800b6775@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7d2fcf7ae ]
There is a race between operations that iterate over the userdata
cg_children list and concurrent add/remove of userdata items through
configfs. The update_userdata() function iterates over the
nt->userdata_group.cg_children list, and count_extradata_entries() also
iterates over this same list to count nodes.
Quoting from Documentation/filesystems/configfs.rst:
> A subsystem can navigate the cg_children list and the ci_parent pointer
> to see the tree created by the subsystem. This can race with configfs'
> management of the hierarchy, so configfs uses the subsystem mutex to
> protect modifications. Whenever a subsystem wants to navigate the
> hierarchy, it must do so under the protection of the subsystem
> mutex.
Without proper locking, if a userdata item is added or removed
concurrently while these functions are iterating, the list can be
accessed in an inconsistent state. For example, the list_for_each() loop
can reach a node that is being removed from the list by list_del_init()
which sets the nodes' .next pointer to point to itself, so the loop will
never end (or reach the WARN_ON_ONCE in update_userdata() ).
Fix this by holding the configfs subsystem mutex (su_mutex) during all
operations that iterate over cg_children.
This includes:
- userdatum_value_store() which calls update_userdata() to iterate over
cg_children
- All sysdata_*_enabled_store() functions which call
count_extradata_entries() to iterate over cg_children
The su_mutex must be acquired before dynamic_netconsole_mutex to avoid
potential lock ordering issues, as configfs operations may already hold
su_mutex when calling into our code.
Fixes: df03f830d0 ("net: netconsole: cache userdata formatted string in netconsole_target")
Signed-off-by: Gustavo Luiz Duarte <gustavold@gmail.com>
Link: https://patch.msgid.link/20251029-netconsole-fix-warn-v1-1-0d0dd4622f48@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c211f5d7cb ]
After registering a VLAN device and setting its feature flags, we need to
synchronize the VLAN features with the lower device. For example, the VLAN
device does not have the NETIF_F_LRO flag, it should be synchronized with
the lower device based on the NETIF_F_UPPER_DISABLES definition.
As the dev->vlan_features has changed, we need to call
netdev_update_features(). The caller must run after netdev_upper_dev_link()
links the lower devices, so this patch adds the netdev_update_features()
call in register_vlan_dev().
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20251030073539.133779-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d01f8136d4 ]
The script "ethtool-common.sh" is not installed in INSTALL_PATH, and
triggers some errors when I try to run the test
'drivers/net/netdevsim/ethtool-coalesce.sh':
TAP version 13
1..1
# timeout set to 600
# selftests: drivers/net/netdevsim: ethtool-coalesce.sh
# ./ethtool-coalesce.sh: line 4: ethtool-common.sh: No such file or directory
# ./ethtool-coalesce.sh: line 25: make_netdev: command not found
# ethtool: bad command line argument(s)
# ./ethtool-coalesce.sh: line 124: check: command not found
# ./ethtool-coalesce.sh: line 126: [: -eq: unary operator expected
# FAILED /0 checks
not ok 1 selftests: drivers/net/netdevsim: ethtool-coalesce.sh # exit=1
Install this file to avoid this error. After this patch:
TAP version 13
1..1
# timeout set to 600
# selftests: drivers/net/netdevsim: ethtool-coalesce.sh
# PASSED all 22 checks
ok 1 selftests: drivers/net/netdevsim: ethtool-coalesce.sh
Fixes: fbb8531e58 ("selftests: extract common functions in ethtool-common.sh")
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Link: https://patch.msgid.link/20251030040340.3258110-1-wangliang74@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8e8486702 ]
The GRO self-test, gro.c, currently constructs IPv6 packets containing a
Hop-by-Hop Options header (IPPROTO_HOPOPTS) to ensure the GRO path
correctly handles IPv6 extension headers.
However, network elements may be configured to drop packets with the
Hop-by-Hop Options header (HBH). This causes the self-test to fail
in environments where such network elements are present.
To improve the robustness and reliability of this test in diverse
network environments, switch from using IPPROTO_HOPOPTS to
IPPROTO_DSTOPTS (Destination Options).
The Destination Options header is less likely to be dropped by
intermediate routers and still serves the core purpose of the test:
validating GRO's handling of an IPv6 extension header. This change
ensures the test can execute successfully without being incorrectly
failed by network policies outside the kernel's control.
Fixes: 7d1575014a ("selftests/net: GRO coalesce test")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Anubhav Singh <anubhavsinggh@google.com>
Link: https://patch.msgid.link/20251030060436.1556664-1-anubhavsinggh@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02d064de05 ]
Due to the gro_sender sending data packets and FIN packets
in very quick succession, these are received almost simultaneously
by the gro_receiver. FIN packets are sometimes processed before the
data packets leading to intermittent (~1/100) test failures.
This change adds a delay of 100ms before sending FIN packets
in gro:tcp test to avoid the out-of-order delivery. The same
mitigation already exists for the gro:ip test.
Fixes: 7d1575014a ("selftests/net: GRO coalesce test")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Anubhav Singh <anubhavsinggh@google.com>
Link: https://patch.msgid.link/20251030062818.1562228-1-anubhavsinggh@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d18a84edd ]
The internal switch on BCM63XX SoCs will unconditionally add 802.1Q VLAN
tags on egress to CPU when 802.1Q mode is enabled. We do this
unconditionally since commit ed409f3bba ("net: dsa: b53: Configure
VLANs while not filtering").
This is fine for VLAN aware bridges, but for standalone ports and vlan
unaware bridges this means all packets are tagged with the default VID,
which is 0.
While the kernel will treat that like untagged, this can break userspace
applications processing raw packets, expecting untagged traffic, like
STP daemons.
This also breaks several bridge tests, where the tcpdump output then
does not match the expected output anymore.
Since 0 isn't a valid VID, just strip out the VLAN tag if we encounter
it, unless the priority field is set, since that would be a valid tag
again.
Fixes: 964dbf186e ("net: dsa: tag_brcm: add support for legacy tags")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20251027194621.133301-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ab753b5d8 ]
gve implemented a ptp_clock for sole use of do_aux_work at this time.
ptp_clock_gettime() and ptp_sys_offset() assume every ptp_clock has
implemented either gettimex64 or gettime64. Stub gettimex64 and return
-EOPNOTSUPP to prevent NULL dereferencing.
Fixes: acd1638052 ("gve: Add initial PTP device support")
Reported-by: syzbot+c8c0e7ccabd456541612@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c8c0e7ccabd456541612
Signed-off-by: Tim Hostetler <thostet@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Link: https://patch.msgid.link/20251029184555.3852952-2-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c21cf89a6 ]
The memory allocated for ptr using kvmalloc() is not freed on the last
error path. Fix that by freeing it on that error path.
Fixes: 9a24ce5e29 ("Bluetooth: btrtl: Firmware format v2 support")
Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c5f1f6468 ]
In hci_cmd_complete_evt(), if the command complete event has an unknown
opcode, we assume the first byte of the remaining skb->data contains the
return status. However, parameter data has previously been pulled in
hci_event_func(), which may leave the skb empty. If so, using skb->data[0]
for the return status uses un-init memory.
The fix is to check skb->len before using skb->data.
Reported-by: syzbot+a9a4bedfca6aa9d7fa24@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a9a4bedfca6aa9d7fa24
Tested-by: syzbot+a9a4bedfca6aa9d7fa24@syzkaller.appspotmail.com
Fixes: afcb3369f4 ("Bluetooth: hci_event: Fix vendor (unknown) opcode status handling")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f838d624fd ]
Patch "Make HID attributes visible" is needed for older kernel versions
(e.g. 6.12) where ufs_get_device_desc() is called from ufshcd_probe_hba().
In these older kernel versions ufshcd_get_device_desc() may be called
after the sysfs attributes have been added. In the upstream kernel however
ufshcd_get_device_desc() is called before ufs_sysfs_add_nodes(). See also
the ufshcd_device_params_init() call from ufshcd_init(). Hence, calling
sysfs_update_group() is not necessary.
See also commit 69f5eb78d4 ("scsi: ufs: core: Move the
ufshcd_device_init(hba, true) call") in kernel v6.13.
This patch fixes the following kernel warning:
sysfs: cannot create duplicate filename '/devices/platform/3c2d0000.ufs/hid'
Workqueue: async async_run_entry_fn
Call trace:
dump_backtrace+0xfc/0x17c
show_stack+0x18/0x28
dump_stack_lvl+0x40/0x104
dump_stack+0x18/0x3c
sysfs_warn_dup+0x6c/0xc8
internal_create_group+0x1c8/0x504
sysfs_create_groups+0x38/0x9c
ufs_sysfs_add_nodes+0x20/0x58
ufshcd_init+0x1114/0x134c
ufshcd_pltfrm_init+0x728/0x7d8
ufs_google_probe+0x30/0x84
platform_probe+0xa0/0xe0
really_probe+0x114/0x454
__driver_probe_device+0xa4/0x160
driver_probe_device+0x44/0x23c
__device_attach_driver+0x15c/0x1f4
bus_for_each_drv+0x10c/0x168
__device_attach_async_helper+0x80/0xf8
async_run_entry_fn+0x4c/0x17c
process_one_work+0x26c/0x65c
worker_thread+0x33c/0x498
kthread+0x110/0x134
ret_from_fork+0x10/0x20
ufshcd 3c2d0000.ufs: ufs_sysfs_add_nodes: sysfs groups creation failed (err = -17)
Cc: Daniel Lee <chullee@google.com>
Cc: Peter Wang <peter.wang@mediatek.com>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Fixes: bb7663dec6 ("scsi: ufs: sysfs: Make HID attributes visible")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Fixes: bb7663dec6 ("scsi: ufs: sysfs: Make HID attributes visible")
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://patch.msgid.link/20251028222433.1108299-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9222582ec5 ]
This reverts commit 4b66d18918.
In [1], Ross Brown reports poor performance of WCN7850 after enabling
power save. Temporarily revert the fix; it will be re-enabled once
the issue is resolved.
Tested-on: WCN7850 hw2.0 PCI WLAN.IOE_HMT.1.1-00011-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Fixes: 4b66d18918 ("wifi: ath12k: Fix missing station power save configuration")
Reported-by: Ross Brown <true.robot.ross@gmail.com>
Closes: https://lore.kernel.org/all/CAMn66qZENLhDOcVJuwUZ3ir89PVtVnQRq9DkV5xjJn1p6BKB9w@mail.gmail.com/ # [1]
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20251028060744.897198-1-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a74f038fa5 ]
The pt_dump_seq_puts() macro incorrectly uses seq_printf() instead of
seq_puts(). This is both a performance issue and conceptually wrong,
as the macro name suggests plain string output (puts) but the
implementation uses formatted output (printf).
The macro is used in ptdump.c:301 to output a newline character. Using
seq_printf() adds unnecessary overhead for format string parsing when
outputting this constant string.
This bug was introduced in commit 59c4da8640 ("riscv: Add support to
dump the kernel page tables") in 2020, which copied the implementation
pattern from other architectures that had the same bug.
Fixes: 59c4da8640 ("riscv: Add support to dump the kernel page tables")
Signed-off-by: Josephine Pfeiffer <hi@josie.lol>
Link: https://lore.kernel.org/r/20251018170451.3355496-1-hi@josie.lol
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 060ea84a48 ]
Unwinding the stack of a task other than current, KASAN would report
"BUG: KASAN: out-of-bounds in walk_stackframe+0x41c/0x460"
There is a same issue on x86 and has been resolved by the commit
84936118bd ("x86/unwind: Disable KASAN checks for non-current tasks")
The solution could be applied to RISC-V too.
This patch also can solve the issue:
https://seclists.org/oss-sec/2025/q4/23
Fixes: 5d8544e2d0 ("RISC-V: Generic library routines and assembly")
Co-developed-by: Jiakai Xu <xujiakai2025@iscas.ac.cn>
Signed-off-by: Jiakai Xu <xujiakai2025@iscas.ac.cn>
Signed-off-by: Chunyan Zhang <zhangchunyan@iscas.ac.cn>
Link: https://lore.kernel.org/r/20251022072608.743484-1-zhangchunyan@iscas.ac.cn
[pjw@kernel.org: clean up checkpatch issues]
Signed-off-by: Paul Walmsley <pjw@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c74dc8ab47 ]
ufs_sysfs_add_nodes() is called concurrently with ufs_get_device_desc().
This may cause the following code to be called before
ufs_sysfs_add_nodes():
sysfs_update_group(&hba->dev->kobj, &ufs_sysfs_hid_group);
If this happens, ufs_sysfs_add_nodes() triggers a kernel warning and
fails. Fix this by calling ufs_sysfs_add_nodes() before SCSI LUNs are
scanned since the sysfs_update_group() call happens from the context of
thread that executes ufshcd_async_scan(). This patch fixes the following
kernel warning:
sysfs: cannot create duplicate filename '/devices/platform/3c2d0000.ufs/hid'
Workqueue: async async_run_entry_fn
Call trace:
dump_backtrace+0xfc/0x17c
show_stack+0x18/0x28
dump_stack_lvl+0x40/0x104
dump_stack+0x18/0x3c
sysfs_warn_dup+0x6c/0xc8
internal_create_group+0x1c8/0x504
sysfs_create_groups+0x38/0x9c
ufs_sysfs_add_nodes+0x20/0x58
ufshcd_init+0x1114/0x134c
ufshcd_pltfrm_init+0x728/0x7d8
ufs_google_probe+0x30/0x84
platform_probe+0xa0/0xe0
really_probe+0x114/0x454
__driver_probe_device+0xa4/0x160
driver_probe_device+0x44/0x23c
__device_attach_driver+0x15c/0x1f4
bus_for_each_drv+0x10c/0x168
__device_attach_async_helper+0x80/0xf8
async_run_entry_fn+0x4c/0x17c
process_one_work+0x26c/0x65c
worker_thread+0x33c/0x498
kthread+0x110/0x134
ret_from_fork+0x10/0x20
ufshcd 3c2d0000.ufs: ufs_sysfs_add_nodes: sysfs groups creation failed (err = -17)
Cc: Daniel Lee <chullee@google.com>
Fixes: bb7663dec6 ("scsi: ufs: sysfs: Make HID attributes visible")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20251014200118.3390839-2-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a04ea57aae upstream.
The device bus LAN ID was obtained from PCI_FUNC(), but when a PF
port is passthrough to a virtual machine, the function number may not
match the actual port index on the device. This could cause the driver
to perform operations such as LAN reset on the wrong port.
Fix this by reading the LAN ID from port status register.
Fixes: a34b3e6ed8 ("net: txgbe: Store PCI info")
Cc: stable@vger.kernel.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/B60A670C1F52CB8E+20251104062321.40059-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa997d2d2a upstream.
The function ring_buffer_map_get_reader() is a bit more strict than the
other get reader functions, and except for certain situations the
rb_get_reader_page() should not return NULL. If it does, it triggers a
warning.
This warning was triggering but after looking at why, it was because
another acceptable situation was happening and it wasn't checked for.
If the reader catches up to the writer and there's still data to be read
on the reader page, then the rb_get_reader_page() will return NULL as
there's no new page to get.
In this situation, the reader page should not be updated and no warning
should trigger.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Vincent Donnefort <vdonnefort@google.com>
Reported-by: syzbot+92a3745cea5ec6360309@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/690babec.050a0220.baf87.0064.GAE@google.com/
Link: https://lore.kernel.org/20251016132848.1b11bb37@gandalf.local.home
Fixes: 117c39200d ("ring-buffer: Introducing ring-buffer mapping functions")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c91afa7610 upstream.
__unregister_trace_fprobe() checks tf->tuser to put it when removing
tprobe. However, disable_trace_fprobe() does not use it and only calls
unregister_fprobe(). Thus it forgets to disable tracepoint_user.
If the trace_fprobe has tuser, put it for unregistering the tracepoint
callbacks when disabling tprobe correctly.
Link: https://lore.kernel.org/all/176244794466.155515.3971904050506100243.stgit@devnote2/
Fixes: 2867495dea ("tracing: tprobe-events: Register tracepoint when enable tprobe event")
Cc: stable@vger.kernel.org
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Tested-by: Beau Belgrave <beaub@linux.microsoft.com>
Reviewed-by: Beau Belgrave <beaub@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10d9dda426 upstream.
Since __tracepoint_user_init() calls tracepoint_user_register() without
initializing tuser->tpoint with given tracpoint, it does not register
tracepoint stub function as callback correctly, and tprobe does not work.
Initializing tuser->tpoint correctly before tracepoint_user_register()
so that it sets up tracepoint callback.
I confirmed below example works fine again.
echo "t sched_switch preempt prev_pid=prev->pid next_pid=next->pid" > /sys/kernel/tracing/dynamic_events
echo 1 > /sys/kernel/tracing/events/tracepoints/sched_switch/enable
cat /sys/kernel/tracing/trace_pipe
Link: https://lore.kernel.org/all/176244793514.155515.6466348656998627773.stgit@devnote2/
Fixes: 2867495dea ("tracing: tprobe-events: Register tracepoint when enable tprobe event")
Reported-by: Beau Belgrave <beaub@linux.microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Tested-by: Beau Belgrave <beaub@linux.microsoft.com>
Reviewed-by: Beau Belgrave <beaub@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
