Don't just wait for the data write completion and execute the target
command. We need to verify if the request completed successfully and not
just sending invalid data. The verification is done in the write request
completion routine. Queue the same work of the command to execute the
target_execute_cmd() on data write.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9f6b1c6946cf49eeba0173e405678b9b7786636b.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To properly respond to host sending more commands than the number of
streams the device advertises, the device needs to be able to reject the
command with a response. Allocate an extra request to handle 1 more
command than the number of streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/256f2ec8f5e042ab692d9593144fa75f3d3ce94b.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resubmit command on completion to fetch more commands and service them
in parallel. Increase the number of work in a queue. Each work will be
for each command allowing them to be processed concurrently. Also, set
them to be unbounded by cpu to improve performance.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/933cf7191b672bf4cfbea4df19af1b08dc1baca9.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can handle multiple commands concurently. Each command services a
stream id. At the moment, the driver will handle 32 outstanding streams,
which is equivalent to 32 commands. Make sure to allocate a matching
number of commands to the number of streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2d806120dcc10c88fef21865b7bc1d2b6604fe42.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Host can assign stream ID value greater than number of streams
allocated. The tcm function needs to keep track of which stream is
available to assign the stream ID. This patch doesn't track that, but at
least it makes sure that there's no Oops if the host send tag with a
value greater than the number of supported streams.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d57b7dfd228199cef811206b1b83ec649f742752.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only allocate up to UASP_SS_EP_COMP_NUM_STREAMS number of session tags.
We should not be using more than UASP_SS_EP_COMP_NUM_STREAMS of tags due
to the number of commands limit we imposed. Each command uses a unique
tag. Any more than that is unnecessary. By limiting it, we can detect an
issue in our driver immediately should we run out of session tags.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/017016ffcab2f3c284d863fc42483b83dbd21b35.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the default bMaxBurst is 0. Set default bMaxBurst to 15 (i.e.
16 bursts) to Data IN and OUT endpoints to improve performance. It
should be fine for a controller that supports less than 16 bursts. It
should be able to negotiate properly with the host at packet level for
the end of burst.
If the controller can't handle a burst of 16, and high performance isn't
important, the user can use BOT protocol from mass_storage gadget driver
instead.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9d6265db4d138e542f281988362bc4392b034d43.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some old builds of Microsoft Windows 10 UASP class driver reject UASP
device with stream count of 2^4. To keep compatibility with both Linux
and Windows, let's increase the stream count to 2^5. Also, internal
tests show that stream count of 2^5 increases performance slightly.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/23bf7f5cb04da691fd6ba0a77babee9ad3195f44.1733876548.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Altmodes with cros_ec are either automatically entered by the EC or
entered by the AP if TBT or USB4 are supported on the system. Due to the
security risk of PCIe tunneling, TBT modes should not be auto entered by
the kernel at this time and will require user intervention.
With this change, a userspace program will need to explicitly activate
the thunderbolt mode on the port and partner in order to enter the mode
and the thunderbolt driver will not automatically enter when a partner
is connected.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.8.Ic14738918e3d026fa2d85e95fb68f8e07a0828d0@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mux configuration is often the final piece of mode entry and can be used
to determine whether a partner altmode is active. When mux configuration
is done, use the active port altmode's SVID to set the partner active
field for all partner alt modes.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.5.I083bf9188947be8cb7460211cfdf3233370a28f6@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The active property of port altmode should be writable (to prevent or
allow partner altmodes from entering) and needs to be part of
typec_altmode_desc so we can initialize the port to an inactive state if
desired.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.3.I794566684ab2965e209f326b08232006eff333f8@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mode in struct typec_altmode is used to indicate the index of the
altmode on a port, partner or plug. It is used in enter mode VDMs but
doesn't make much sense for matching against altmode drivers or for
matching partner to port altmodes.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20241213153543.v5.1.Ie0d37646f18461234777d88b4c3e21faed92ed4f@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC state in sysfs (/sys/class/udc/<udc>/state) should accurately
reflect the current state of the USB Device Controller.
Currently, the UDC state is not handled consistently during gadget
disconnection. While the disconnect interrupt path correctly sets the
state to "not-attached", manual deconfiguration leaves the state in
"configured", misrepresenting the actual situation.
This commit ensures consistent UDC state handling by setting the state to
"not-attached" after manual deconfiguration. This accurately reflects the
UDC's state and provides a consistent behavior regardless of the
disconnection method.
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Tested-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241223042536.1465299-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-usbip-v1-1-20d611a9bfa4@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-usb-v1-1-19a137c0f20a@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes issue where memory will fail to be allocated for larger bulk
transfers, ~1 MB or more. This occurs because userland libraries, such
as libusb, send the entire USB data buffer when SG support is detected.
The assumption is that the driver knows how to properly split the data
up before sending it out.
By hardcoding a limit, bigger transfers that exceed the SG tablesize
limit of 32 will be unable to use SG. This results in an attempt to
allocate contiguous pages which, unsurprisingly, will fail too and
returns an ENOMEM. It looks like other drivers that support SG allow for
any length of SG lists. Accepting any SG size allows the driver to
properly handle large bulk transfer situations.
Tested bulk read and write operations using the following devices:
- Logitech Webcam Pro 9000 - USB 2.0
- SanDisk Ultra - USB 3.0
- Logitech M500s Mouse
Signed-off-by: Jason Long <jasonlongball@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20241218161344.202637-1-jasonlongball@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a new AMS for responding to a "Get_Revision" request.
Revision message consists of the following fields:
+----------------------------------------------------+
| Header | RMDO |
| No. of data objects = 1 | |
+----------------------------------------------------+
While RMDO consists of:
* B31..28 Revision Major
* B27..24 Revision Minor
* B23..20 Version Major
* B19..16 Version Minor
* B15..0 Reserved, shall be set to zero.
As per the PD spec ("8.3.3.16.2.1 PR_Give_Revision State"), a request is
only expected when an explicit contract is established and the port is
in ready state. This AMS is only supported for PD >= 3.0.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-3-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for parsing "pd-revision" DT property in TCPM and store PD
revision and version supported by the Type-C connnector.
It should be noted that the PD revision is the maximum possible revision
supported by the port. This is different from the 2 bit revision set in
PD msg headers. The purpose of the 2 bit revision value is to negotiate
between Rev 2.X & 3.X spec rev as part of contract negotiation, while
this is used for Get_Revision AMS after a contract is in place.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-2-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add pd-revision property definition, to specify the maximum Power
Delivery Revision and Version supported by the connector.
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241210-get_rev_upstream-v2-1-d0094e52d48f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring
its role preference when operating as a dual-role port
through the SOURCE_PREF field of the General Control Register.
The previous driver behavior was to set the role preference
based on the dr_set typec_operation.
However, the controller does not support swapping the data role
on an active connection due to its lack of Power Delivery support.
Remove previous dr_set typec_operation, and support setting
the role preference based on the corresponding fwnode property,
as well as the try_role typec_operation.
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-3-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring the port type
it will operate as through the MODE_SELECT field of the General
Control Register.
Configure the port type based on the fwnode property "power-role"
during probe, if present. If the property is absent, leave the
operation mode at the default, which is defined by the PORT pin
of the chip.
Support configuring the port type through the port_type_set
typec_operation as well.
The MODE_SELECT field can only be changed when the controller is in
unattached state, so follow the sequence recommended by the datasheet to:
1. disable termination on CC pins to disable the controller
2. change the mode
3. re-enable termination
This will effectively cause a connected device to disconnect
for the duration of the mode change.
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-2-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI HD3SS3220 Type-C controller supports configuring its advertised
power operation mode over I2C using the CURRENT_MODE_ADVERTISE field
of the Connection Status Register.
Configure this power mode based on the existing (optional) property
"typec-power-opmode" of /schemas/connector/usb-connector.yaml
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Oliver Facklam <oliver.facklam@zuehlke.com>
Link: https://lore.kernel.org/r/20241211-usb-typec-controller-enhancements-v3-1-e4bc1b6e1441@zuehlke.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the FSUSB42 USB switches are described, enable support for DP on
the three USB-C ports of the X1E80100 QCP. It supports up to 4 lanes, but
for now we need to limit this to 2 lanes due to limitations in the USB/DP
combo PHY driver. The same limitation also exists on other boards upstream.
Co-developed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241212-x1e80100-qcp-dp-v1-3-37cb362a0dfe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike most X1E boards, the QCP does not have Parade PS8830 retimers on the
three USB-C ports. Instead, there are FSUSB42 USB switches for each port
that handle orientation switching for the SBU lines. The overall setup is
similar to the gpio-sbu-mux defined for sc8280xp-crd and the ThinkPad X13s.
Co-developed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241212-x1e80100-qcp-dp-v1-2-37cb362a0dfe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a compatible entry for the onsemi FSUSB42 USB switch, which can be used
for switching orientation of the SBU lines in USB Type-C applications.
Drivers work as-is with the existing fallback compatible.
Link to datasheet: https://www.onsemi.com/pdf/datasheet/fsusb42-d.pdf
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241212-x1e80100-qcp-dp-v1-1-37cb362a0dfe@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cc1 and cc2 status returned by tcpci_get_cc() may be TYPEC_CC_OPEN
or TYPEC_CC_RA. So don't assume it's just TYPEC_CC_RD or TYPEC_CC_RP_*.
This will let local port present Rd on CC only when cc1/cc2 status is
TYPEC_CC_RP_*.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241211105753.1205312-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If controller looses power during PM suspend then re-initialize
it. We use the DEBUG_CFG register to track if controller lost power
or was reset in PM suspend.
Move all initialization code into dwc3_ti_init() so it can be re-used.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241212-am62-dwc3-io-ddr-v3-1-10b95cd7e9c0@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds documentation for two USB functions:
- usb_otg_state_string(), which returns a human-readable name for OTG
states and
- usb_get_dr_mode_from_string(), which returns the dual role mode for a
given string.
Signed-off-by: Lucy Mielke <lucymielke@icloud.com>
Link: https://lore.kernel.org/r/6nvegfmo6d5ak4soaf5nyifsaasfts4qlsnnpsd4sgpnikc2jd@amfmgdr5n3bi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function pmc_mux_port_debugfs_init() the buffer for
the name of the port is limited to six bytes. That makes the
compiler think that the output of "port%d" may be truncated.
That can't actually happen as the interface can support
maximum of eight ports. To make the compiler happy just
increase the buffer to where the warning goes away.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412031437.vX580pxx-lkp@intel.com/
Cc: Rajat Khandelwal <rajat.khandelwal@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241205113919.1182673-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Disable AVIC on SNP-enabled systems that don't allow writes to the virtual
APIC page, as such hosts will hit unexpected RMP #PFs in the host when
running VMs of any flavor.
- Fix a WARN in the hypercall completion path due to KVM trying to determine
if a guest with protected register state is in 64-bit mode (KVM's ABI is to
assume such guests only make hypercalls in 64-bit mode).
- Allow the guest to write to supported bits in MSR_AMD64_DE_CFG to fix a
regression with Windows guests, and because KVM's read-only behavior appears
to be entirely made up.
- Treat TDP MMU faults as spurious if the faulting access is allowed given the
existing SPTE. This fixes a benign WARN (other than the WARN itself) due to
unexpectedly replacing a writable SPTE with a read-only SPTE.
- Emit a warning when KVM is configured with ignore_msrs=1 and also to hide the
MSRs that the guest is looking for from the kernel logs. ignore_msrs can
trick guests into assuming that certain processor features are present, and
this in turn leads to bogus bug reports.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmdoSTgUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroM+IggAndK6byvsGjU0lM5v4WhKMnD7KZXi
PsXuzv7LQUtbOaosowbBDUfMkZXwewmgUjBWmJL8WFlVePk7+8Aj29Zwd4vH3cHI
KZ/AeyC6VwH1CFLZMSoHgG2dCl8hUUkUldZLAdYKigTRMlw5FmnmIfhqx/mpxiMz
xHs9TU+NZpaQVXSzq9P1AXkJX+zZvyYlGXrTRtJ541AwYPWsq1MBr1megtBi59ws
zEgCOyBpDHWQEasbtwHjPNNH+rCi8SEq2QCrSGHpTXWLS9kXj32wLldWb6E3L5ta
c1/Q9mQDpVXQNidnAWyhukVmbETQDkpB+j9Mfd+bwIy1+zh6iSEe9dWM9g==
=/fW+
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM x86 fixes from Paolo Bonzini:
- Disable AVIC on SNP-enabled systems that don't allow writes to the
virtual APIC page, as such hosts will hit unexpected RMP #PFs in the
host when running VMs of any flavor.
- Fix a WARN in the hypercall completion path due to KVM trying to
determine if a guest with protected register state is in 64-bit mode
(KVM's ABI is to assume such guests only make hypercalls in 64-bit
mode).
- Allow the guest to write to supported bits in MSR_AMD64_DE_CFG to fix
a regression with Windows guests, and because KVM's read-only
behavior appears to be entirely made up.
- Treat TDP MMU faults as spurious if the faulting access is allowed
given the existing SPTE. This fixes a benign WARN (other than the
WARN itself) due to unexpectedly replacing a writable SPTE with a
read-only SPTE.
- Emit a warning when KVM is configured with ignore_msrs=1 and also to
hide the MSRs that the guest is looking for from the kernel logs.
ignore_msrs can trick guests into assuming that certain processor
features are present, and this in turn leads to bogus bug reports.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: let it be known that ignore_msrs is a bad idea
KVM: VMX: don't include '<linux/find.h>' directly
KVM: x86/mmu: Treat TDP MMU faults as spurious if access is already allowed
KVM: SVM: Allow guest writes to set MSR_AMD64_DE_CFG bits
KVM: x86: Play nice with protected guests in complete_hypercall_exit()
KVM: SVM: Disable AVIC on SNP-enabled system without HvInUseWrAllowed feature
- Disable AVIC on SNP-enabled systems that don't allow writes to the virtual
APIC page, as such hosts will hit unexpected RMP #PFs in the host when
running VMs of any flavor.
- Fix a WARN in the hypercall completion path due to KVM trying to determine
if a guest with protected register state is in 64-bit mode (KVM's ABI is to
assume such guests only make hypercalls in 64-bit mode).
- Allow the guest to write to supported bits in MSR_AMD64_DE_CFG to fix a
regression with Windows guests, and because KVM's read-only behavior appears
to be entirely made up.
- Treat TDP MMU faults as spurious if the faulting access is allowed given the
existing SPTE. This fixes a benign WARN (other than the WARN itself) due to
unexpectedly replacing a writable SPTE with a read-only SPTE.
-----BEGIN PGP SIGNATURE-----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=S9jc
-----END PGP SIGNATURE-----
Merge tag 'kvm-x86-fixes-6.13-rcN' of https://github.com/kvm-x86/linux into HEAD
KVM x86 fixes for 6.13:
- Disable AVIC on SNP-enabled systems that don't allow writes to the virtual
APIC page, as such hosts will hit unexpected RMP #PFs in the host when
running VMs of any flavor.
- Fix a WARN in the hypercall completion path due to KVM trying to determine
if a guest with protected register state is in 64-bit mode (KVM's ABI is to
assume such guests only make hypercalls in 64-bit mode).
- Allow the guest to write to supported bits in MSR_AMD64_DE_CFG to fix a
regression with Windows guests, and because KVM's read-only behavior appears
to be entirely made up.
- Treat TDP MMU faults as spurious if the faulting access is allowed given the
existing SPTE. This fixes a benign WARN (other than the WARN itself) due to
unexpectedly replacing a writable SPTE with a read-only SPTE.
When running KVM with ignore_msrs=1 and report_ignored_msrs=0, the user has
no clue that that the guest is being lied to. This may cause bug reports
such as https://gitlab.com/qemu-project/qemu/-/issues/2571, where enabling
a CPUID bit in QEMU caused Linux guests to try reading MSR_CU_DEF_ERR; and
being lied about the existence of MSR_CU_DEF_ERR caused the guest to assume
other things about the local APIC which were not true:
Sep 14 12:02:53 kernel: mce: [Firmware Bug]: Your BIOS is not setting up LVT offset 0x2 for deferred error IRQs correctly.
Sep 14 12:02:53 kernel: unchecked MSR access error: RDMSR from 0x852 at rIP: 0xffffffffb548ffa7 (native_read_msr+0x7/0x40)
Sep 14 12:02:53 kernel: Call Trace:
...
Sep 14 12:02:53 kernel: native_apic_msr_read+0x20/0x30
Sep 14 12:02:53 kernel: setup_APIC_eilvt+0x47/0x110
Sep 14 12:02:53 kernel: mce_amd_feature_init+0x485/0x4e0
...
Sep 14 12:02:53 kernel: [Firmware Bug]: cpu 0, try to use APIC520 (LVT offset 2) for vector 0xf4, but the register is already in use for vector 0x0 on this cpu
Without reported_ignored_msrs=0 at least the host kernel log will contain
enough information to avoid going on a wild goose chase. But if reports
about individual MSR accesses are being silenced too, at least complain
loudly the first time a VM is started.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The header clearly states that it does not want to be included directly,
only via '<linux/bitmap.h>'. Replace the include accordingly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Message-ID: <20241217070539.2433-2-wsa+renesas@sang-engineering.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
