[ Upstream commit 11ba7ce076 ]
Vlad Poenaru reported the following kmemleak issue:
unreferenced object 0x606fd7c44ac8 (size 32):
backtrace (crc 0):
pcpu_alloc_noprof+0x730/0xeb0
bpf_map_alloc_percpu+0x69/0xc0
prealloc_init+0x9d/0x1b0
htab_map_alloc+0x363/0x510
map_create+0x215/0x3a0
__sys_bpf+0x16b/0x3e0
__x64_sys_bpf+0x18/0x20
do_syscall_64+0x7b/0x150
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Further investigation shows the reason is due to not 8-byte aligned
store of percpu pointer in htab_elem_set_ptr():
*(void __percpu **)(l->key + key_size) = pptr;
Note that the whole htab_elem alignment is 8 (for x86_64). If the key_size
is 4, that means pptr is stored in a location which is 4 byte aligned but
not 8 byte aligned. In mm/kmemleak.c, scan_block() scans the memory based
on 8 byte stride, so it won't detect above pptr, hence reporting the memory
leak.
In htab_map_alloc(), we already have
htab->elem_size = sizeof(struct htab_elem) +
round_up(htab->map.key_size, 8);
if (percpu)
htab->elem_size += sizeof(void *);
else
htab->elem_size += round_up(htab->map.value_size, 8);
So storing pptr with 8-byte alignment won't cause any problem and can fix
kmemleak too.
The issue can be reproduced with bpf selftest as well:
1. Enable CONFIG_DEBUG_KMEMLEAK config
2. Add a getchar() before skel destroy in test_hash_map() in prog_tests/for_each.c.
The purpose is to keep map available so kmemleak can be detected.
3. run './test_progs -t for_each/hash_map &' and a kmemleak should be reported.
Reported-by: Vlad Poenaru <thevlad@meta.com>
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20250224175514.2207227-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcc47a028c ]
As the null algorithm may be freed in softirq context through
af_alg, use spin locks instead of mutexes to protect the default
null algorithm.
Reported-by: syzbot+b3e02953598f447d4d2a@syzkaller.appspotmail.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1047e21aec ]
The HAVE_ARCH Kconfig options in lib/crypto try to solve the
modular versus built-in problem, but it still fails when the
the LIB option (e.g., CRYPTO_LIB_CURVE25519) is selected externally.
Fix this by introducing a level of indirection with ARCH_MAY_HAVE
Kconfig options, these then go on to select the ARCH_HAVE options
if the ARCH Kconfig options matches that of the LIB option.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501230223.ikroNDr1-lkp@intel.com/
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cb345939b ]
PCI device 0x1134 shares same register features as PCI device 0x17E0.
Hence reuse same data for the new PCI device ID 0x1134.
Signed-off-by: Devaraj Rangasamy <Devaraj.Rangasamy@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e27fbe16af ]
Some information that should be retrieved at runtime for the Coherence
Manager can be either absent or wrong. This patch allows checking if
some of this information is available from the device tree and updates
the internal variable accordingly.
For now, only the compatible string associated with the broken HCI is
being retrieved.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b0671b97f ]
irq_mask()/irq_unmask() are not called for nested interrupts. So level
interrupts are never masked, chip's interrupt output is not cleared on
INTCAP or GPIO read, the irq handler is uselessly called again. Nested
irq handler is not called again, because interrupt reason is cleared by
its first call.
/proc/interrupts shows that number of chip's irqs is greater than
number of nested irqs.
This patch adds masking and unmasking level interrupts inside irq handler.
Signed-off-by: Dmitry Mastykin <mastichi@gmail.com>
Link: https://lore.kernel.org/20250122120504.1279790-1-mastichi@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b99f27e902 ]
Fix a race condition between the main test_progs thread and the traffic
monitoring thread. The traffic monitor thread tries to print a line
using multiple printf and use flockfile() to prevent the line from being
torn apart. Meanwhile, the main thread doing io redirection can reassign
or close stdout when going through tests. A deadlock as shown below can
happen.
main traffic_monitor_thread
==== ======================
show_transport()
-> flockfile(stdout)
stdio_hijack_init()
-> stdout = open_memstream(log_buf, log_cnt);
...
env.subtest_state->stdout_saved = stdout;
...
funlockfile(stdout)
stdio_restore_cleanup()
-> fclose(env.subtest_state->stdout_saved);
After the traffic monitor thread lock stdout, A new memstream can be
assigned to stdout by the main thread. Therefore, the traffic monitor
thread later will not be able to unlock the original stdout. As the
main thread tries to access the old stdout, it will hang indefinitely
as it is still locked by the traffic monitor thread.
The deadlock can be reproduced by running test_progs repeatedly with
traffic monitor enabled:
for ((i=1;i<=100;i++)); do
./test_progs -a flow_dissector_skb* -m '*'
done
Fix this by only calling printf once and remove flockfile()/funlockfile().
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250213233217.553258-1-ameryhung@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1fdc4dca35 upstream.
wdm_wwan_port_tx_complete is called from a completion
handler with irqs disabled and possible in IRQ context
usb_autopm_put_interface can take a mutex.
Hence usb_autopm_put_interface_async must be used.
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-4-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1846ed4eb upstream.
Clearing WDM_WWAN_IN_USE must be the last action or
we can open a chardev whose URBs are still poisoned
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-3-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9697f5efcf upstream.
In case submitting the URB fails we must undo
what we've done so far.
Fixes: cac6fb015f ("usb: class: cdc-wdm: WWAN framework integration")
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250401084749.175246-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37ffdbd695 upstream.
The SanDisk 3.2Gen1 Flash Drive, which VID:PID is in 0781:55a3,
just like Silicon Motion Flash Drive:
https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
also needs the DELAY_INIT quirk, or it will randomly work incorrectly
(e.g.: lsusb and can't list this device info) when connecting Huawei
hisi platforms and doing thousand of reboot test circles.
Cc: stable <stable@kernel.org>
Signed-off-by: Miao Li <limiao@kylinos.cn>
Signed-off-by: Lei Huang <huanglei@kylinos.cn>
Link: https://lore.kernel.org/r/20250414062935.159024-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2932b6b547 upstream.
Silicon Motion Flash Drive connects to Huawei hisi platforms and
performs a system reboot test for two thousand circles, it will
randomly work incorrectly on boot, set DELAY_INIT quirk can workaround
this issue.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250401023027.44894-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38d6e60b6f upstream.
The "reset" GPIO controls the RESET signal to an external, usually
ULPI PHY, chip. The original code path acquires the signal in LOW
state, and then immediately asserts it HIGH again, if the reset
signal defaulted to asserted, there'd be a short "spike" before the
reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found during code inspection.
Also remove the cryptic "toggle ulpi .." comment.
Fixes: ca05b38252 ("usb: dwc3: xilinx: Add gpio-reset support")
Cc: stable <stable@kernel.org>
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250318064518.9320-1-mike.looijmans@topic.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63ccd26cd1 upstream.
The event count is read from register DWC3_GEVNTCOUNT.
There is a check for the count being zero, but not for exceeding the
event buffer length.
Check that event count does not exceed event buffer length,
avoiding an out-of-bounds access when memcpy'ing the event.
Crash log:
Unable to handle kernel paging request at virtual address ffffffc0129be000
pc : __memcpy+0x114/0x180
lr : dwc3_check_event_buf+0xec/0x348
x3 : 0000000000000030 x2 : 000000000000dfc4
x1 : ffffffc0129be000 x0 : ffffff87aad60080
Call trace:
__memcpy+0x114/0x180
dwc3_interrupt+0x24/0x34
Signed-off-by: Frode Isaksen <frode@meta.com>
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250403072907.448524-1-fisaksen@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcb60d4385 upstream.
The OHCI controller (rev 0x02) under LS7A PCI host has a hardware flaw.
MMIO register with offset 0x60/0x64 is treated as legacy PS2-compatible
keyboard/mouse interface, which confuse the OHCI controller. Since OHCI
only use a 4KB BAR resource indeed, the LS7A OHCI controller's 32KB BAR
is wrapped around (the second 4KB BAR space is the same as the first 4KB
internally). So we can add an 4KB offset (0x1000) to the OHCI registers
(from the PCI BAR resource) as a quirk.
Cc: stable <stable@kernel.org>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Mingcong Bai <baimingcong@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20250328040059.3672979-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c531e0a8c upstream.
usb_phy_init() may return an error code if e.g. its implementation fails
to prepare/enable some clocks. And properly rollback on probe error path
by calling the counterpart usb_phy_shutdown().
Found by Linux Verification Center (linuxtesting.org).
Fixes: be9cae2479 ("usb: chipidea: imx: Fix ULPI on imx53")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-4-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cab0e9a3f upstream.
Upon encountering errors during the HSIC pinctrl handling section the
regulator should be disabled.
Use devm_add_action_or_reset() to let the regulator-disabling routine be
handled by device resource management stack.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4d6141288c ("usb: chipidea: imx: pinctrl for HSIC is optional")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e28f79e3d upstream.
usbmisc is an optional device property so it is totally valid for the
corresponding data->usbmisc_data to have a NULL value.
Check that before dereferencing the pointer.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.
Fixes: 74adad5003 ("usb: chipidea: ci_hdrc_imx: decrement device's refcount in .remove() and in the error path of .probe()")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250316102658.490340-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1059896f2 upstream.
The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit
58f2fcb3a8 ("usb: cdnsp: Fix deadlock issue during using NCM gadget").
Under PREEMPT_RT the deadlock can be readily triggered by heavy network
traffic, for example using "iperf --bidir" over NCM ethernet link.
The deadlock occurs because the threaded interrupt handler gets
preempted by a softirq, but both are protected by the same spinlock.
Prevent deadlock by disabling softirq during threaded irq handler.
Cc: stable <stable@kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20250318-rfs-cdns3-deadlock-v2-1-bfd9cfcee732@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ea050da55 upstream.
This check is performed before prepare_transfer() and prepare_ring(), so
enqueue can already point at the final link TRB of a segment. And indeed
it will, some 0.4% of times this code is called.
Then enqueue + 1 is an invalid pointer. It will crash the kernel right
away or load some junk which may look like a link TRB and cause the real
link TRB to be replaced with a NOOP. This wouldn't end well.
Use a functionally equivalent test which doesn't dereference the pointer
and always gives correct result.
Something has crashed my machine twice in recent days while playing with
an Etron HC, and a control transfer stress test ran for confirmation has
just crashed it again. The same test passes with this patch applied.
Fixes: 5e1c67abc9 ("xhci: Fix control transfer error on Etron xHCI host")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bea5892d0e upstream.
Current xhci bus resume implementation prevents xHC host from generating
interrupts during high-speed USB 2 and super-speed USB 3 bus resume.
Only reason to disable interrupts during bus resume would be to prevent
the interrupt handler from interfering with the resume process of USB 2
ports.
Host initiated resume of USB 2 ports is done in two stages.
The xhci driver first transitions the port from 'U3' to 'Resume' state,
then wait in Resume for 20ms, and finally moves port to U0 state.
xhci driver can't prevent interrupts by keeping the xhci spinlock
due to this 20ms sleep.
Limit interrupt disabling to the USB 2 port resume case only.
resuming USB 2 ports in bus resume is only done in special cases where
USB 2 ports had to be forced to suspend during bus suspend.
The current way of preventing interrupts by clearing the 'Interrupt
Enable' (INTE) bit in USBCMD register won't prevent the Interrupter
registers 'Interrupt Pending' (IP), 'Event Handler Busy' (EHB) and
USBSTS register Event Interrupt (EINT) bits from being set.
New interrupts can't be issued before those bits are properly clered.
Disable interrupts by clearing the interrupter register 'Interrupt
Enable' (IE) bit instead. This way IP, EHB and INTE won't be set
before IE is enabled again and a new interrupt is triggered.
Reported-by: Devyn Liu <liudingyuan@huawei.com>
Closes: https://lore.kernel.org/linux-usb/b1a9e2d51b4d4ff7a304f77c5be8164e@huawei.com/
Cc: stable@vger.kernel.org
Tested-by: Devyn Liu <liudingyuan@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250410151828.2868740-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cc01410e1 upstream.
Add serial support for OWON HDS200 series oscilloscopes and likely
many other pieces of OWON test equipment.
OWON HDS200 series devices host two USB endpoints, designed to
facilitate bidirectional SCPI. SCPI is a predominately ASCII text
protocol for test/measurement equipment. Having a serial/tty interface
for these devices lowers the barrier to entry for anyone trying to
write programs to communicate with them.
The following shows the USB descriptor for the OWON HDS272S running
firmware V5.7.1:
Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope
Negotiated speed: Full Speed (12Mbps)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 [unknown]
bDeviceSubClass 0 [unknown]
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x5345 Owon
idProduct 0x1234 PDS6062T Oscilloscope
bcdDevice 1.00
iManufacturer 1 oscilloscope
iProduct 2 oscilloscope
iSerial 3 oscilloscope
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0029
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 5 Physical Interface Device
bInterfaceSubClass 0 [unknown]
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 09 21 11 01 00 01 22 5f 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 32
Device Status: 0x0000
(Bus Powered)
OWON appears to be using the same USB Vendor and Product ID for many
of their oscilloscopes. Looking at the discussion about the USB
vendor/product ID, in the link bellow, suggests that this VID/PID is
shared with VDS, SDS, PDS, and now the HDS series oscilloscopes.
Available documentation for these devices seems to indicate that all
use a similar SCPI protocol, some with RS232 options. It is likely that
this same simple serial setup would work correctly for them all.
Link: https://usb-ids.gowdy.us/read/UD/5345/1234
Signed-off-by: Craig Hesling <craig@hesling.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b399078f88 upstream.
Abacus Electrics makes optical probes for interacting with smart meters
over an optical interface.
At least one version uses an FT232B chip (as detected by ftdi_sio) with
a custom USB PID, which needs to be added to the list to make the device
work in a plug-and-play fashion.
Signed-off-by: Michael Ehrenreich <michideep@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1ca3ff28a upstream.
startup()/shutdown() callbacks access SIFIVE_SERIAL_IE_OFFS.
The register is also accessed from write() callback.
If console were printing and startup()/shutdown() callback
gets called, its access to the register could be overwritten.
Add port->lock to startup()/shutdown() callbacks to make sure
their access to SIFIVE_SERIAL_IE_OFFS is synchronized against
write() callback.
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Signed-off-by: Ryo Takakura <ryotkkr98@gmail.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Rule: add
Link: https://lore.kernel.org/stable/20250330003522.386632-1-ryotkkr98%40gmail.com
Link: https://lore.kernel.org/r/20250412001847.183221-1-ryotkkr98@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7094832b5a upstream.
The MSM UART DM controller supports different working modes, e.g. DMA or
the "single-character mode", where all reads/writes operate on a single
character rather than 4 chars (32-bit) at once. When using earlycon,
__msm_console_write() always writes 4 characters at a time, but we don't
know which mode the bootloader was using and we don't set the mode either.
This causes garbled output if the bootloader was using the single-character
mode, because only every 4th character appears in the serial console, e.g.
"[ 00oni pi 000xf0[ 00i s 5rm9(l)l s 1 1 SPMTA 7:C 5[ 00A ade k d[
00ano:ameoi .Q1B[ 00ac _idaM00080oo'"
If the bootloader was using the DMA ("DM") mode, output would likely fail
entirely. Later, when the full serial driver probes, the port is
re-initialized and output works as expected.
Fix this also for earlycon by clearing the DMEN register and
reset+re-enable the transmitter to apply the change. This ensures the
transmitter is in the expected state before writing any output.
Cc: stable <stable@kernel.org>
Fixes: 0efe729634 ("tty: serial: msm: Add earlycon support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250408-msm-serial-earlycon-v1-1-429080127530@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee6a44da3c upstream.
This requirement was overeagerly loosened in commit 2f83e38a09
("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), but as
it turns out,
(1) the logic I implemented there was inconsistent (apologies!),
(2) TIOCL_SELMOUSEREPORT might actually be a small security risk
after all, and
(3) TIOCL_SELMOUSEREPORT is only meant to be used by the mouse
daemon (GPM or Consolation), which runs as CAP_SYS_ADMIN
already.
In more detail:
1. The previous patch has inconsistent logic:
In commit 2f83e38a09 ("tty: Permit some TIOCL_SETSEL modes
without CAP_SYS_ADMIN"), we checked for sel_mode ==
TIOCL_SELMOUSEREPORT, but overlooked that the lower four bits of
this "mode" parameter were actually used as an additional way to
pass an argument. So the patch did actually still require
CAP_SYS_ADMIN, if any of the mouse button bits are set, but did not
require it if none of the mouse buttons bits are set.
This logic is inconsistent and was not intentional. We should have
the same policies for using TIOCL_SELMOUSEREPORT independent of the
value of the "hidden" mouse button argument.
I sent a separate documentation patch to the man page list with
more details on TIOCL_SELMOUSEREPORT:
https://lore.kernel.org/all/20250223091342.35523-2-gnoack3000@gmail.com/
2. TIOCL_SELMOUSEREPORT is indeed a potential security risk which can
let an attacker simulate "keyboard" input to command line
applications on the same terminal, like TIOCSTI and some other
TIOCLINUX "selection mode" IOCTLs.
By enabling mouse reporting on a terminal and then injecting mouse
reports through TIOCL_SELMOUSEREPORT, an attacker can simulate
mouse movements on the same terminal, similar to the TIOCSTI
keystroke injection attacks that were previously possible with
TIOCSTI and other TIOCL_SETSEL selection modes.
Many programs (including libreadline/bash) are then prone to
misinterpret these mouse reports as normal keyboard input because
they do not expect input in the X11 mouse protocol form. The
attacker does not have complete control over the escape sequence,
but they can at least control the values of two consecutive bytes
in the binary mouse reporting escape sequence.
I went into more detail on that in the discussion at
https://lore.kernel.org/all/20250221.0a947528d8f3@gnoack.org/
It is not equally trivial to simulate arbitrary keystrokes as it
was with TIOCSTI (commit 83efeeeb3d ("tty: Allow TIOCSTI to be
disabled")), but the general mechanism is there, and together with
the small number of existing legit use cases (see below), it would
be better to revert back to requiring CAP_SYS_ADMIN for
TIOCL_SELMOUSEREPORT, as it was already the case before
commit 2f83e38a09 ("tty: Permit some TIOCL_SETSEL modes without
CAP_SYS_ADMIN").
3. TIOCL_SELMOUSEREPORT is only used by the mouse daemons (GPM or
Consolation), and they are the only legit use case:
To quote console_codes(4):
The mouse tracking facility is intended to return
xterm(1)-compatible mouse status reports. Because the console
driver has no way to know the device or type of the mouse, these
reports are returned in the console input stream only when the
virtual terminal driver receives a mouse update ioctl. These
ioctls must be generated by a mouse-aware user-mode application
such as the gpm(8) daemon.
Jared Finder has also confirmed in
https://lore.kernel.org/all/491f3df9de6593df8e70dbe77614b026@finder.org/
that Emacs does not call TIOCL_SELMOUSEREPORT directly, and it
would be difficult to find good reasons for doing that, given that
it would interfere with the reports that GPM is sending.
More information on the interaction between GPM, terminals and the
kernel with additional pointers is also available in this patch:
https://lore.kernel.org/all/a773e48920aa104a65073671effbdee665c105fc.1603963593.git.tammo.block@gmail.com/
For background on who else uses TIOCL_SELMOUSEREPORT: Debian Code
search finds one page of results, the only two known callers are
the two mouse daemons GPM and Consolation. (GPM does not show up
in the search results because it uses literal numbers to refer to
TIOCLINUX-related enums. I looked through GPM by hand instead.
TIOCL_SELMOUSEREPORT is also not used from libgpm.)
https://codesearch.debian.net/search?q=TIOCL_SELMOUSEREPORT
Cc: Jared Finder <jared@finder.org>
Cc: Jann Horn <jannh@google.com>
Cc: Hanno Böck <hanno@hboeck.de>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: stable <stable@kernel.org>
Fixes: 2f83e38a09 ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN")
Signed-off-by: Günther Noack <gnoack3000@gmail.com>
Link: https://lore.kernel.org/r/20250411070144.3959-2-gnoack3000@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d239f447f upstream.
Add of_platform_default_populate() to stratix10-svc
driver as the firmware/svc node was moved out of soc.
This fixes the failed probing of child drivers of
svc node.
Cc: stable@vger.kernel.org
Fixes: 23c3ebed38 ("arm64: dts: socfpga: agilex: move firmware out of soc node")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Mahesh Rao <mahesh.rao@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20250326115446.36123-1-dinguyen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9d7748a74 upstream.
Under irq_ack, pci1xxxx_assign_bit reads the current interrupt status,
modifies and writes the entire value back. Since, the IRQ status bit
gets cleared on writing back, the better approach is to directly write
the bitmask to the register in order to preserve the value.
Fixes: 1f4d8ae231 ("misc: microchip: pci1xxxx: Add gpio irq handler and irq helper functions irq_ack, irq_mask, irq_unmask and irq_set_type of irq_chip.")
Cc: stable <stable@kernel.org>
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20250313170856.20868-3-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18eb77c75e upstream.
Resolve kernel panic while accessing IRQ handler associated with the
generated IRQ. This is done by acquiring the spinlock and storing the
current interrupt state before handling the interrupt request using
generic_handle_irq.
A previous fix patch was submitted where 'generic_handle_irq' was
replaced with 'handle_nested_irq'. However, this change also causes
the kernel panic where after determining which GPIO triggered the
interrupt and attempting to call handle_nested_irq with the mapped
IRQ number, leads to a failure in locating the registered handler.
Fixes: 194f9f94a5 ("misc: microchip: pci1xxxx: Resolve kernel panic during GPIO IRQ handling")
Cc: stable <stable@kernel.org>
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20250313170856.20868-2-rengarajan.s@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c876be906c upstream.
register_chrdev will only register the first 256 minors of a major chrdev.
That means that dynamically allocated misc devices with minor above 255
will fail to open with -ENXIO.
This was found by kernel test robot when testing a different change that
makes all dynamically allocated minors be above 255. This has, however,
been separately tested by creating 256 serio_raw devices with the help of
userio driver.
Ever since allowing misc devices with minors above 128, this has been
possible.
Fix it by registering all minor numbers from 0 to MINORMASK + 1 for
MISC_MAJOR.
Reported-by: kernel test robot <oliver.sang@intel.com>
Cc: stable <stable@kernel.org>
Closes: https://lore.kernel.org/oe-lkp/202503171507.6c8093d0-lkp@intel.com
Fixes: ab760791c0 ("char: misc: Increase the maximum number of dynamic misc devices to 1048448")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Tested-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Link: https://lore.kernel.org/r/20250317-misc-chrdev-v1-1-6cd05da11aef@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1fb088d9c upstream.
Take irqfds.lock when adding/deleting an IRQ bypass producer to ensure
irqfd->producer isn't modified while kvm_irq_routing_update() is running.
The only lock held when a producer is added/removed is irqbypass's mutex.
Fixes: 8727688006 ("KVM: x86: select IRQ_BYPASS_MANAGER")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bcac97dc4 upstream.
Restore an IRTE back to host control (remapped or posted MSI mode) if the
*new* GSI route prevents posting the IRQ directly to a vCPU, regardless of
the GSI routing type. Updating the IRTE if and only if the new GSI is an
MSI results in KVM leaving an IRTE posting to a vCPU.
The dangling IRTE can result in interrupts being incorrectly delivered to
the guest, and in the worst case scenario can result in use-after-free,
e.g. if the VM is torn down, but the underlying host IRQ isn't freed.
Fixes: efc644048e ("KVM: x86: Update IRTE for posted-interrupts")
Fixes: 411b44ba80 ("svm: Implements update_pi_irte hook to setup posted interrupt")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcda70c56f upstream.
Explicitly treat type differences as GSI routing changes, as comparing MSI
data between two entries could get a false negative, e.g. if userspace
changed the type but left the type-specific data as-is.
Fixes: 515a0c79e7 ("kvm: irqfd: avoid update unmodified entries of the routing")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00f1cc14da upstream.
gcc 15 honors the __counted_by(len) attribute on vsc_tp_packet.buf[]
and the vsc-tp.c code is using this in a wrong way. len does not contain
the available size in the buffer, it contains the actual packet length
*without* the crc. So as soon as vsc_tp_xfer() tries to add the crc to
buf[] the fortify-panic handler gets triggered:
[ 80.842193] memcpy: detected buffer overflow: 4 byte write of buffer size 0
[ 80.842243] WARNING: CPU: 4 PID: 272 at lib/string_helpers.c:1032 __fortify_report+0x45/0x50
...
[ 80.843175] __fortify_panic+0x9/0xb
[ 80.843186] vsc_tp_xfer.cold+0x67/0x67 [mei_vsc_hw]
[ 80.843210] ? seqcount_lockdep_reader_access.constprop.0+0x82/0x90
[ 80.843229] ? lockdep_hardirqs_on+0x7c/0x110
[ 80.843250] mei_vsc_hw_start+0x98/0x120 [mei_vsc]
[ 80.843270] mei_reset+0x11d/0x420 [mei]
The easiest fix would be to just drop the counted-by but with the exception
of the ack buffer in vsc_tp_xfer_helper() which only contains enough room
for the packet-header, all other uses of vsc_tp_packet always use a buffer
of VSC_TP_MAX_XFER_SIZE bytes for the packet.
Instead of just dropping the counted-by, split the vsc_tp_packet struct
definition into a header and a full-packet definition and use a fixed
size buf[] in the packet definition, this way fortify-source buffer
overrun checking still works when enabled.
Fixes: 566f5ca976 ("mei: Add transport driver for IVSC device")
Cc: stable@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Alexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250318141203.94342-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14a3cc7558 upstream.
With ATA devices supporting the CDL feature, using CDL requires that the
feature be enabled with a SET FEATURES command. This command is issued
as the translated command for the MODE SELECT command issued by
scsi_cdl_enable() when the user enables CDL through the device
cdl_enable sysfs attribute.
However, the implementation of scsi_cdl_enable() always issues a MODE
SELECT command for ATA devices when the enable argument is true, even if
CDL is already enabled on the device. While this does not cause any
issue with using CDL descriptors with read/write commands (the CDL
feature will be enabled on the drive), issuing the MODE SELECT command
even when the device CDL feature is already enabled will cause a reset
of the ATA device CDL statistics log page (as defined in ACS, any CDL
enable action must reset the device statistics).
Avoid this needless actions (and the implied statistics log page reset)
by modifying scsi_cdl_enable() to issue the MODE SELECT command to
enable CDL if and only if CDL is not reported as already enabled on the
device.
And while at it, simplify the initialization of the is_ata boolean
variable and move the declaration of the scsi mode data and sense header
variables to within the scope of ATA device handling.
Fixes: 1b22cfb141 ("scsi: core: Allow enabling and disabling command duration limits")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ab75eee1a upstream.
Version 1.60 specifically needs this quirk.
Version 2.00 is known good.
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250403180004.343133-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88474ad734 upstream.
For the ATA features subpage of the control mode page, the T10 SAT-6
specifications state that:
For a MODE SENSE command, the SATL shall return the CDL_CTRL field value
that was last set by an application client.
However, the function ata_msense_control_ata_feature() always sets the
CDL_CTRL field to the 0x02 value to indicate support for the CDL T2A and
T2B pages. This is thus incorrect and the value 0x02 must be reported
only after the user enables the CDL feature, which is indicated with the
ATA_DFLAG_CDL_ENABLED device flag. When this flag is not set, the
CDL_CTRL field of the ATA feature subpage of the control mode page must
report a value of 0x00.
Fix ata_msense_control_ata_feature() to report the correct values for
the CDL_CTRL field, according to the enable/disable state of the device
CDL feature.
Fixes: df60f9c645 ("scsi: ata: libata: Add ATA feature control sub-page translation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db91586b1e upstream.
The function ata_mselect_control_ata_feature() has a return type defined
as unsigned int but this function may return negative error codes, which
are correctly propagated up the call chain as integers.
Fix ata_mselect_control_ata_feature() to have the correct int return
type.
While at it, also fix a typo in this function description comment.
Fixes: df60f9c645 ("scsi: ata: libata: Add ATA feature control sub-page translation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17e897a456 upstream.
With ATA devices supporting the CDL feature, using CDL requires that the
feature be enabled with a SET FEATURES command. This command is issued
as the translated command for the MODE SELECT command issued by
scsi_cdl_enable() when the user enables CDL through the device
cdl_enable sysfs attribute.
Currently, ata_mselect_control_ata_feature() always translates a MODE
SELECT command for the ATA features subpage of the control mode page to
a SET FEATURES command to enable or disable CDL based on the cdl_ctrl
field. However, there is no need to issue the SET FEATURES command if:
1) The MODE SELECT command requests disabling CDL and CDL is already
disabled.
2) The MODE SELECT command requests enabling CDL and CDL is already
enabled.
Fix ata_mselect_control_ata_feature() to issue the SET FEATURES command
only when necessary. Since enabling CDL also implies a reset of the CDL
statistics log page, avoiding useless CDL enable operations also avoids
clearing the CDL statistics log.
Also add debug messages to clearly signal when CDL is being enabled or
disabled using a SET FEATURES command.
Fixes: df60f9c645 ("scsi: ata: libata: Add ATA feature control sub-page translation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c7f1bfdb2 upstream.
In chameleon_parse_gdd(), if mcb_device_register() fails, 'mdev'
would be released in mcb_device_register() via put_device().
Thus, goto 'err' label and free 'mdev' again causes a double free.
Just return if mcb_device_register() fails.
Fixes: 3764e82e51 ("drivers: Introduce MEN Chameleon Bus")
Cc: stable <stable@kernel.org>
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Signed-off-by: Johannes Thumshirn <jth@kernel.org>
Link: https://lore.kernel.org/r/6201d09e2975ae5789879f79a6de4c38de9edd4a.1741596225.git.jth@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 078d3ee7c1 upstream.
According to CXL r3.2 section 8.2.1.2, the PCI_COMMAND register fields,
including Memory Space Enable bit, have no effect on the behavior of an
RCD Upstream Port. Retaining this check may incorrectly cause
cxl_pci_probe() to fail on a valid RCD upstream Port.
While the specification is explicit only for RCD Upstream Ports, this
check is solely for accessing the RCRB, which is always mapped through
memory space. Therefore, its safe to remove the check entirely. In
practice, firmware reliably enables the Memory Space Enable bit for
RCH Downstream Ports and no failures have been observed.
Removing the check simplifies the code and avoids unnecessary
special-casing, while relying on BIOS/firmware to configure devices
correctly. Moreover, any failures due to inaccessible RCRB regions
will still be caught either in __rcrb_to_component() or while
parsing the component register block.
The following failure was observed in dmesg when the check was present:
cxl_pci 0000:7f:00.0: No component registers (-6)
Fixes: d5b1a27143 ("cxl/acpi: Extract component registers of restricted hosts from RCRB")
Signed-off-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Link: https://patch.msgid.link/20250407192734.70631-1-Smita.KoralahalliChannabasappa@amd.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7537deda36 upstream.
Allocate SVM's interrupt remapping metadata using GFP_ATOMIC as
svm_ir_list_add() is called with IRQs are disabled and irqfs.lock held
when kvm_irq_routing_update() reacts to GSI routing changes.
Fixes: 411b44ba80 ("svm: Implements update_pi_irte hook to setup posted interrupt")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250404193923.1413163-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edd43f4d6f upstream.
A previous commit added a 'sync' parameter to io_fallback_tw(), which if
true, means the caller wants to wait on the fallback thread handling it.
But the logic is somewhat messed up, ensure that ctxs are swapped and
flushed appropriately.
Cc: stable@vger.kernel.org
Fixes: dfbe5561ae ("io_uring: flush offloaded and delayed task_work on exit")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5add0dbbeb upstream.
In function kvm_pre_enter_guest(), it prepares to enter guest and check
whether there are pending signals or events. And it will not enter guest
if there are, PMU pass-through preparation for guest should be cancelled
and host should own PMU hardware.
Cc: stable@vger.kernel.org
Fixes: f4e40ea9f7 ("LoongArch: KVM: Add PMU support for guest")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ea86232a5 upstream.
Some registers such as LOONGARCH_CSR_ESTAT and LOONGARCH_CSR_GINTC are
partly cleared with function _kvm_setcsr(). This comes from the hardware
specification, some bits are read only in VM mode, and however they can
be written in host mode. So they are partly cleared in VM mode, and can
be fully cleared in host mode.
These read only bits show pending interrupt or exception status. When VM
reset, the read-only bits should be cleared, otherwise vCPU will receive
unknown interrupts in boot stage.
Here registers LOONGARCH_CSR_ESTAT/LOONGARCH_CSR_GINTC are fully cleared
in ioctl KVM_REG_LOONGARCH_VCPU_RESET vCPU reset path.
Cc: stable@vger.kernel.org
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
