[ Upstream commit 2bdf1d428f ]
R-Car V4H Reference Manual R19UH0186EJ0130 Rev.1.30 Apr. 21, 2025 page 4581
Figure 104.3b Initial Setting of PCIEC(example), third quarter of the
figure indicates that register 0xf8 should be polled until bit 18 becomes
set to 1.
Register 0xf8, bit 18 is 0 immediately after write to PCIERSTCTRL1 and is
set to 1 in less than 1 ms afterward. The current readl_poll_timeout()
break condition is inverted and returns when register 0xf8, bit 18 is set
to 0, which in most cases means immediately. In case
CONFIG_DEBUG_LOCK_ALLOC=y, the timing changes just enough for the first
readl_poll_timeout() poll to already read register 0xf8, bit 18 as 1 and
afterward never read register 0xf8, bit 18 as 0, which leads to timeout
and failure to start the PCIe controller.
Fix this by inverting the poll condition to match the reference manual
initialization sequence.
Fixes: faf5a975ee ("PCI: rcar-gen4: Add support for R-Car V4H")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250915235910.47768-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0056d29f8c ]
Assure the reset is latched and the core is ready for DBI access. On R-Car
V4H, the PCIe reset is asynchronous and does not take effect immediately,
but needs a short time to complete. In case DBI access happens in that
short time, that access generates an SError. Make sure that condition can
never happen, read back the state of the reset, which should turn the
asynchronous reset into a synchronous one, and wait a little over 1ms to
add additional safety margin.
Fixes: 0d0c551011 ("PCI: rcar-gen4: Add R-Car Gen4 PCIe controller support for host mode")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250924005610.96484-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8795b70581 ]
R-Car V4H Reference Manual R19UH0186EJ0130 Rev.1.30 Apr. 21, 2025 page 585
Figure 9.3.2 Software Reset flow (B) indicates that for peripherals in HSC
domain, after reset has been asserted by writing a matching reset bit into
register SRCR, it is mandatory to wait 1ms.
Because it is the controller driver which can determine whether or not the
controller is in HSC domain based on its compatible string, add the missing
delay in the controller driver.
This 1ms delay is documented on R-Car V4H and V4M; it is currently unclear
whether S4 is affected as well. This patch does apply the extra delay on
R-Car S4 as well.
Fixes: 0d0c551011 ("PCI: rcar-gen4: Add R-Car Gen4 PCIe controller support for host mode")
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[mani: added the missing r-b tag from Krzysztof]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250919134644.208098-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e40b984b6c ]
The VHCI platform driver aims to forbid entering system suspend when at
least one of the virtual USB ports are bound to an active USB/IP
connection.
However, in some cases, the detection logic doesn't work reliably, i.e.
when all devices attached to the virtual root hub have been already
suspended, leading to a broken suspend state, with unrecoverable resume.
Ensure the virtually attached devices do not enter suspend by setting
the syscore PM flag. Note this is currently limited to the client side
only, since the server side doesn't implement system suspend prevention.
Fixes: 04679b3489 ("Staging: USB/IP: add client driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250902-vhci-hcd-suspend-fix-v3-1-864e4e833559@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79dde5f7dc ]
The cpu_latency_qos_add/remove/update_request interfaces lack internal
synchronization by design, requiring the caller to ensure thread safety.
The current implementation relies on the 'pm_qos_enabled' flag, which is
insufficient to prevent concurrent access and cannot serve as a proper
synchronization mechanism. This has led to data races and list
corruption issues.
A typical race condition call trace is:
[Thread A]
ufshcd_pm_qos_exit()
--> cpu_latency_qos_remove_request()
--> cpu_latency_qos_apply();
--> pm_qos_update_target()
--> plist_del <--(1) delete plist node
--> memset(req, 0, sizeof(*req));
--> hba->pm_qos_enabled = false;
[Thread B]
ufshcd_devfreq_target
--> ufshcd_devfreq_scale
--> ufshcd_scale_clks
--> ufshcd_pm_qos_update <--(2) pm_qos_enabled is true
--> cpu_latency_qos_update_request
--> pm_qos_update_target
--> plist_del <--(3) plist node use-after-free
Introduces a dedicated mutex to serialize PM QoS operations, preventing
data races and ensuring safe access to PM QoS resources, including sysfs
interface reads.
Fixes: 2777e73fc1 ("scsi: ufs: core: Add CPU latency QoS support for UFS driver")
Signed-off-by: Zhongqiu Han <zhongqiu.han@oss.qualcomm.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Huan Tang <tanghuan@vivo.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5ba345b2d ]
ct_seq_show() has an opportunistic garbage collector :
if (nf_ct_should_gc(ct)) {
nf_ct_kill(ct);
goto release;
}
So if one nf_conn is killed there, next time ct_get_next() runs,
we skip the following item in the bucket, even if it should have
been displayed if gc did not take place.
We can decrement st->skip_elems to tell ct_get_next() one of the items
was removed from the chain.
Fixes: 58e207e498 ("netfilter: evict stale entries when user reads /proc/net/nf_conntrack")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09efbac953 ]
During a batch replay, the nlh pointer is not reset until the parsing of
the commands. Since commit bf2ac490d2 ("netfilter: nfnetlink: Handle
ACK flags for batch messages") that is problematic as the condition to
add an ACK for batch begin will evaluate to true even if NLM_F_ACK
wasn't used for batch begin message.
If there is an error during the command processing, netlink is sending
an ACK despite that. This misleads userspace tools which think that the
return code was 0. Reset the nlh pointer to the original one when a
replay is triggered.
Fixes: bf2ac490d2 ("netfilter: nfnetlink: Handle ACK flags for batch messages")
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 134121bfd9 ]
On the netns cleanup path, __ip_vs_ftp_exit() may unregister ip_vs_ftp
before connections with valid cp->app pointers are flushed, leading to a
use-after-free.
Fix this by introducing a global `exiting_module` flag, set to true in
ip_vs_ftp_exit() before unregistering the pernet subsystem. In
__ip_vs_ftp_exit(), skip ip_vs_ftp unregister if called during netns
cleanup (when exiting_module is false) and defer it to
__ip_vs_cleanup_batch(), which unregisters all apps after all connections
are flushed. If called during module exit, unregister ip_vs_ftp
immediately.
Fixes: 61b1ab4583 ("IPVS: netns, add basic init per netns.")
Suggested-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Slavin Liu <slavin452@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8ab231782 ]
Timestamping configuration through ethtool has inconsistent behavior of
skipping the reply for set command if configuration was not changed. Fix
it be providing reply in any case.
Fixes: 6e9e2eed4f ("net: ethtool: Add support for tsconfig command to get/set hwtstamp config")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250922231924.2769571-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 191512355e ]
When the client max_resp_sz is larger than what the server encodes in
its reply, the nfs4_verify_back_channel_attrs() check fails and this
causes nfs4_proc_create_session() to fail, in cases where the client
page size is larger than that of the server and the server does not want
to negotiate upwards.
While this is not a problem with the linux nfs server that will reflect
the proposed value in its reply irrespective of the local page size,
other nfs server implementations may insist on their own max_resp_sz
value, which could be smaller.
Fix this by accepting smaller max_resp_sz values from the server, as
this does not violate the protocol. The server is allowed to decrease
but not increase proposed the size, and as such values smaller than the
client-proposed ones are valid.
Fixes: 43c2e885be ("nfs4: fix channel attribute sanity-checks")
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70714eb724 ]
The return value of devm_kzalloc could be an null pointer,
use "!desc.pdata" to fix incorrect handling return value
of devm_kzalloc.
Fixes: 4277f035d2 ("coresight: trbe: Add a representative coresight_platform_data for TRBE")
Signed-off-by: Lin Yujun <linyujun809@h-partners.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250908122022.1315399-1-linyujun809@h-partners.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43e0a92c04 ]
Some TPDM devices support both CMB and DSB datasets, requiring
the system to enable the port with both corresponding element sizes.
Currently, the logic treats tpdm_read_element_size as successful if
the CMB element size is retrieved correctly, regardless of whether
the DSB element size is obtained. This behavior causes issues
when parsing data from TPDM devices that depend on both element sizes.
To address this, the function should explicitly fail if the DSB
element size cannot be read correctly.
Fixes: e6d7f5252f ("coresight-tpda: Add support to configure CMB element")
Reviewed-by: James Clark <james.clark@linaro.org>
Signed-off-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250906-fix_element_size_issue-v2-1-dbb0ac2541a9@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a55c161f7 ]
When the TRBE driver fails to allocate a buffer, it currently returns
the error code "-ENOMEM". However, the caller etm_setup_aux() only
checks for a NULL pointer, so it misses the error. As a result, the
driver continues and eventually causes a kernel panic.
Fix this by returning a NULL pointer from arm_trbe_alloc_buffer() on
allocation failures. This allows that the callers can properly handle
the failure.
Fixes: 3fbf7f011f ("coresight: sink: Add TRBE driver")
Reported-by: Tamas Zsoldos <tamas.zsoldos@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250904-cs_etm_auxsetup_fix_error_handling-v2-1-a502d0bafb95@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d091c63125 ]
The programming clock is enabled by AMBA bus driver before a dynamic
probe. As a result, a CoreSight driver may redundantly enable the same
clock.
To avoid this, add a check for device type and skip enabling the
programming clock for AMBA devices. The returned NULL pointer will be
tolerated by the drivers.
Fixes: 73d779a03a ("coresight: etm4x: Change etm4_platform_driver driver for MMIO devices")
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250731-arm_cs_fix_clock_v4-v6-6-1dfe10bb3f6f@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8f2d480f1 ]
Some CoreSight components have trace bus clocks 'atclk' and are enabled
using clk_prepare_enable(). These clocks are not disabled when modules
exit.
As atclk is optional, use devm_clk_get_optional_enabled() to manage it.
The benefit is the driver model layer can automatically disable and
release clocks.
Check the returned value with IS_ERR() to detect errors but leave the
NULL pointer case if the clock is not found. And remove the error
handling codes which are no longer needed.
Fixes: d1839e6877 ("coresight: etm: retrieve and handle atclk")
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250731-arm_cs_fix_clock_v4-v6-5-1dfe10bb3f6f@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1abc1b212e ]
Some CoreSight components have programming clocks (pclk) and are enabled
using clk_get() and clk_prepare_enable(). However, in many cases, these
clocks are not disabled when modules exit and only released by clk_put().
To fix the issue, this commit refactors programming clock by replacing
clk_get() and clk_prepare_enable() with devm_clk_get_optional_enabled()
for enabling APB clock. If the "apb_pclk" clock is not found, a NULL
pointer is returned, and the function proceeds to attempt enabling the
"apb" clock.
Since ACPI platforms rely on firmware to manage clocks, returning a NULL
pointer in this case leaves clock management to the firmware rather than
the driver. This effectively avoids a clock imbalance issue during
module removal - where the clock could be disabled twice: once during
the ACPI runtime suspend and again during the devm resource release.
Callers are updated to reuse the returned error value.
With the change, programming clocks are managed as resources in driver
model layer, allowing clock cleanup to be handled automatically. As a
result, manual cleanup operations are no longer needed and are removed
from the Coresight drivers.
Fixes: 73d779a03a ("coresight: etm4x: Change etm4_platform_driver driver for MMIO devices")
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250731-arm_cs_fix_clock_v4-v6-4-1dfe10bb3f6f@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40c0cdc9cb ]
The atclk is an optional clock for the CoreSight ETMv4, but the driver
misses to initialize it.
This change enables atclk in probe of the ETMv4 driver, and dynamically
control the clock during suspend and resume.
No need to check the driver data and clock pointer in the runtime
suspend and resume, so remove checks. And add error handling in the
resume function.
Add a minor fix to the comment format when adding the atclk field.
Fixes: 2e1cdfe184 ("coresight-etm4x: Adding CoreSight ETM4x driver")
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250731-arm_cs_fix_clock_v4-v6-3-1dfe10bb3f6f@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5483624eff ]
The atclk is an optional clock for the CoreSight CATU, but the driver
misses to initialize it.
This change enables atclk in probe of the CATU driver, and dynamically
control the clock during suspend and resume.
The checks for driver data and clocks in suspend and resume are not
needed, remove them. Add error handling in the resume function.
Fixes: fcacb5c154 ("coresight: Introduce support for Coresight Address Translation Unit")
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250731-arm_cs_fix_clock_v4-v6-2-1dfe10bb3f6f@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a79026926 ]
The atclk is an optional clock for the CoreSight TMC, but the driver
misses to initialize it. In most cases, TMC shares the atclk clock with
other CoreSight components. Since these components enable the clock
before the TMC device is initialized, the TMC continues properly,
which is why we don’t observe any lockup issues.
This change enables atclk in probe of the TMC driver. Given the clock
is optional, it is possible to return NULL if the clock does not exist.
IS_ERR() is tolerant for this case.
Dynamically disable and enable atclk during suspend and resume. The
clock pointers will never be error values if the driver has successfully
probed, and the case of a NULL pointer case will be handled by the clock
core layer. The driver data is always valid after probe. Therefore,
remove the related checks. Also in the resume flow adds error handling.
Fixes: bc4bf7fe98 ("coresight-tmc: add CoreSight TMC driver")
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: James Clark <james.clark@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250731-arm_cs_fix_clock_v4-v6-1-1dfe10bb3f6f@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcdc42f5dc ]
The TRCEXTINSELR is only implemented if TRCIDR5.NUMEXTINSEL > 0.
To avoid invalid accesses, introduce a check on numextinsel
(derived from TRCIDR5[11:9]) before reading or writing to this register.
Fixes: f5bd523690 ("coresight: etm4x: Convert all register accesses")
Signed-off-by: Yuanfang Zhang <yuanfang.zhang@oss.qualcomm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20250812-trcextinselr_issue-v2-1-e6eb121dfcf4@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ddf6d3fcb ]
The return values of VDO_ASSERT calls that validate metadata are not acted
upon.
Return UDS_CORRUPT_DATA in case of an error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a4eb7e2555 ("dm vdo: implement the volume index")
Signed-off-by: Ivan Abramov <i.abramov@mt-integration.ru>
Reviewed-by: Matthew Sakai <msakai@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e32edc694 ]
Flush cache failures were observed after RX queue update for TID
delete. This occurred because the queue was invalid during flush.
Set the VLD bit in the RX queue update command for TID delete.
This ensures the queue remains valid during the flush cache process.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250806111750.3214584-7-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c32476253 ]
Refactor RX TID deletion handling by moving the REO command
setup and send sequence into a new helper function:
ath12k_dp_rx_tid_delete_handler().
This improves code readability and modularity, and prepares
the codebase for potential reuse of the REO command logic in
other contexts where RX TID deletion is required.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250806111750.3214584-3-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Stable-dep-of: 5e32edc694 ("wifi: ath12k: Fix flush cache failure during RX queue update")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 142964960c ]
The ADSP firmware on X1E has separate firmware binaries for the main
firmware and the DTB. The same applies for the "lite" firmware loaded by
the boot firmware.
When preparing to load the new ADSP firmware we shutdown the lite_pas_id
for the main firmware, but we don't shutdown the corresponding lite pas_id
for the DTB. The fact that we're leaving it "running" forever becomes
obvious if you try to reuse (or just access) the memory region used by the
"lite" firmware: The &adsp_boot_mem is accessible, but accessing the
&adsp_boot_dtb_mem results in a crash.
We don't support reusing the memory regions currently, but nevertheless we
should not keep part of the lite firmware running. Fix this by adding the
lite_dtb_pas_id and shutting it down as well.
We don't have a way to detect if the lite firmware is actually running yet,
so ignore the return status of qcom_scm_pas_shutdown() for now. This was
already the case before, the assignment to "ret" is not used anywhere.
Fixes: 62210f7509 ("remoteproc: qcom_q6v5_pas: Unload lite firmware on ADSP")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250820-rproc-qcom-q6v5-fixes-v2-3-910b1a3aff71@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 110be46f5a ]
enable_irq() and disable_irq() are reference counted, so we must make sure
that each enable_irq() is always paired with a single disable_irq(). If we
call disable_irq() twice followed by just a single enable_irq(), the IRQ
will remain disabled forever.
For the error handling path in qcom_q6v5_wait_for_start(), disable_irq()
will end up being called twice, because disable_irq() also happens in
qcom_q6v5_unprepare() when rolling back the call to qcom_q6v5_prepare().
Fix this by dropping disable_irq() in qcom_q6v5_wait_for_start(). Since
qcom_q6v5_prepare() is the function that calls enable_irq(), it makes more
sense to have the rollback handled always by qcom_q6v5_unprepare().
Fixes: 3b415c8fb2 ("remoteproc: q6v5: Extract common resource handling")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Link: https://lore.kernel.org/r/20250820-rproc-qcom-q6v5-fixes-v2-1-910b1a3aff71@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f152338e3 ]
During PERST# assertion tegra_pcie_bpmp_set_pll_state() is currently
called twice.
pex_ep_event_pex_rst_assert() should do the opposite of
pex_ep_event_pex_rst_deassert(), so it is obvious that the duplicate
tegra_pcie_bpmp_set_pll_state() is a mistake, and that the duplicate
tegra_pcie_bpmp_set_pll_state() call should instead be a call to
tegra_pcie_bpmp_set_ctrl_state().
With this, the uninitialization sequence also matches that of
tegra_pcie_unconfig_controller().
Fixes: a54e190737 ("PCI: tegra194: Add Tegra234 PCIe support")
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
[cassel: improve commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250911093021.1454385-2-cassel@kernel.org
[mani: added Fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 570f945117 ]
Lockdep gives a splat [1] when ser_hdl_work item is executed. It is
scheduled at mac80211 workqueue via ieee80211_queue_work() and takes a
wiphy lock inside. However, this workqueue can be flushed when e.g.
closing the interface and wiphy lock is already taken in that case.
Choosing wiphy_work_queue() for SER is likely not suitable. Back on to
the global workqueue.
[1]:
WARNING: possible circular locking dependency detected
6.17.0-rc2 #17 Not tainted
------------------------------------------------------
kworker/u32:1/61 is trying to acquire lock:
ffff88811bc00768 (&rdev->wiphy.mtx){+.+.}-{4:4}, at: ser_state_run+0x5e/0x180 [rtw89_core]
but task is already holding lock:
ffffc9000048fd30 ((work_completion)(&ser->ser_hdl_work)){+.+.}-{0:0}, at: process_one_work+0x7b5/0x1450
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 ((work_completion)(&ser->ser_hdl_work)){+.+.}-{0:0}:
process_one_work+0x7c6/0x1450
worker_thread+0x49e/0xd00
kthread+0x313/0x640
ret_from_fork+0x221/0x300
ret_from_fork_asm+0x1a/0x30
-> #1 ((wq_completion)phy0){+.+.}-{0:0}:
touch_wq_lockdep_map+0x8e/0x180
__flush_workqueue+0x129/0x10d0
ieee80211_stop_device+0xa8/0x110
ieee80211_do_stop+0x14ce/0x2880
ieee80211_stop+0x13a/0x2c0
__dev_close_many+0x18f/0x510
__dev_change_flags+0x25f/0x670
netif_change_flags+0x7b/0x160
do_setlink.isra.0+0x1640/0x35d0
rtnl_newlink+0xd8c/0x1d30
rtnetlink_rcv_msg+0x700/0xb80
netlink_rcv_skb+0x11d/0x350
netlink_unicast+0x49a/0x7a0
netlink_sendmsg+0x759/0xc20
____sys_sendmsg+0x812/0xa00
___sys_sendmsg+0xf7/0x180
__sys_sendmsg+0x11f/0x1b0
do_syscall_64+0xbb/0x360
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #0 (&rdev->wiphy.mtx){+.+.}-{4:4}:
__lock_acquire+0x124c/0x1d20
lock_acquire+0x154/0x2e0
__mutex_lock+0x17b/0x12f0
ser_state_run+0x5e/0x180 [rtw89_core]
rtw89_ser_hdl_work+0x119/0x220 [rtw89_core]
process_one_work+0x82d/0x1450
worker_thread+0x49e/0xd00
kthread+0x313/0x640
ret_from_fork+0x221/0x300
ret_from_fork_asm+0x1a/0x30
other info that might help us debug this:
Chain exists of:
&rdev->wiphy.mtx --> (wq_completion)phy0 --> (work_completion)(&ser->ser_hdl_work)
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock((work_completion)(&ser->ser_hdl_work));
lock((wq_completion)phy0);
lock((work_completion)(&ser->ser_hdl_work));
lock(&rdev->wiphy.mtx);
*** DEADLOCK ***
2 locks held by kworker/u32:1/61:
#0: ffff888103835148 ((wq_completion)phy0){+.+.}-{0:0}, at: process_one_work+0xefa/0x1450
#1: ffffc9000048fd30 ((work_completion)(&ser->ser_hdl_work)){+.+.}-{0:0}, at: process_one_work+0x7b5/0x1450
stack backtrace:
CPU: 0 UID: 0 PID: 61 Comm: kworker/u32:1 Not tainted 6.17.0-rc2 #17 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS edk2-20250523-14.fc42 05/23/2025
Workqueue: phy0 rtw89_ser_hdl_work [rtw89_core]
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
print_circular_bug.cold+0x178/0x1be
check_noncircular+0x14c/0x170
__lock_acquire+0x124c/0x1d20
lock_acquire+0x154/0x2e0
__mutex_lock+0x17b/0x12f0
ser_state_run+0x5e/0x180 [rtw89_core]
rtw89_ser_hdl_work+0x119/0x220 [rtw89_core]
process_one_work+0x82d/0x1450
worker_thread+0x49e/0xd00
kthread+0x313/0x640
ret_from_fork+0x221/0x300
ret_from_fork_asm+0x1a/0x30
</TASK>
Found by Linux Verification Center (linuxtesting.org).
Fixes: ebfc9199df ("wifi: rtw89: add wiphy_lock() to work that isn't held wiphy_lock() yet")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250919210852.823912-5-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9f0064f47 ]
If there is no rtwsta_link found in rtw89_core_send_nullfunc(), allocated
skb is leaked. Free it on the error handling path.
Found by Linux Verification Center (linuxtesting.org).
Fixes: a8ba4acab7 ("wifi: rtw89: send nullfunc based on the given link")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250919210852.823912-4-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c56325259a ]
The test will fail as below on x86_64 with cpu la57 support (will skip if
no la57 support). Note, the test requries nr_hugepages to be set first.
# running bash ./va_high_addr_switch.sh
# -------------------------------------
# mmap(addr_switch_hint - pagesize, pagesize): 0x7f55b60fa000 - OK
# mmap(addr_switch_hint - pagesize, (2 * pagesize)): 0x7f55b60f9000 - OK
# mmap(addr_switch_hint, pagesize): 0x800000000000 - OK
# mmap(addr_switch_hint, 2 * pagesize, MAP_FIXED): 0x800000000000 - OK
# mmap(NULL): 0x7f55b60f9000 - OK
# mmap(low_addr): 0x40000000 - OK
# mmap(high_addr): 0x1000000000000 - OK
# mmap(high_addr) again: 0xffff55b6136000 - OK
# mmap(high_addr, MAP_FIXED): 0x1000000000000 - OK
# mmap(-1): 0xffff55b6134000 - OK
# mmap(-1) again: 0xffff55b6132000 - OK
# mmap(addr_switch_hint - pagesize, pagesize): 0x7f55b60fa000 - OK
# mmap(addr_switch_hint - pagesize, 2 * pagesize): 0x7f55b60f9000 - OK
# mmap(addr_switch_hint - pagesize/2 , 2 * pagesize): 0x7f55b60f7000 - OK
# mmap(addr_switch_hint, pagesize): 0x800000000000 - OK
# mmap(addr_switch_hint, 2 * pagesize, MAP_FIXED): 0x800000000000 - OK
# mmap(NULL, MAP_HUGETLB): 0x7f55b5c00000 - OK
# mmap(low_addr, MAP_HUGETLB): 0x40000000 - OK
# mmap(high_addr, MAP_HUGETLB): 0x1000000000000 - OK
# mmap(high_addr, MAP_HUGETLB) again: 0xffff55b5e00000 - OK
# mmap(high_addr, MAP_FIXED | MAP_HUGETLB): 0x1000000000000 - OK
# mmap(-1, MAP_HUGETLB): 0x7f55b5c00000 - OK
# mmap(-1, MAP_HUGETLB) again: 0x7f55b5a00000 - OK
# mmap(addr_switch_hint - pagesize, 2*hugepagesize, MAP_HUGETLB): 0x800000000000 - FAILED
# mmap(addr_switch_hint , 2*hugepagesize, MAP_FIXED | MAP_HUGETLB): 0x800000000000 - OK
# [FAIL]
addr_switch_hint is defined as DFEFAULT_MAP_WINDOW in the failed test (for
x86_64, DFEFAULT_MAP_WINDOW is defined as (1UL<<47) - pagesize) in 64 bit.
Before commit cc92882ee2 ("mm: drop hugetlb_get_unmapped_area{_*}
functions"), for x86_64 hugetlb_get_unmapped_area() is handled in arch
code arch/x86/mm/hugetlbpage.c and addr is checked with
map_address_hint_valid() after align with 'addr &= huge_page_mask(h)'
which is a round down way, and it will fail the check because the addr is
within the DEFAULT_MAP_WINDOW but (addr + len) is above the
DFEFAULT_MAP_WINDOW. So it wil go through the
hugetlb_get_unmmaped_area_top_down() to find an area within the
DFEFAULT_MAP_WINDOW.
After commit cc92882ee2 ("mm: drop hugetlb_get_unmapped_area{_*}
functions"). The addr hint for hugetlb_get_unmmaped_area() will be
rounded up and aligned to hugepage size with ALIGN() for all arches. And
after the align, the addr will be above the default MAP_DEFAULT_WINDOW,
and the map_addresshint_valid() check will pass because both aligned addr
(addr0) and (addr + len) are above the DEFAULT_MAP_WINDOW, and the aligned
hint address (0x800000000000) is returned as an suitable gap is found
there, in arch_get_unmapped_area_topdown().
To still cover the case that addr is within the DEFAULT_MAP_WINDOW, and
addr + len is above the DFEFAULT_MAP_WINDOW, change to choose the last
hugepage aligned address within the DEFAULT_MAP_WINDOW as the hint addr,
and the addr + len (2 hugepages) will be one hugepage above the
DEFAULT_MAP_WINDOW. An aligned address won't be affected by the page
round up or round down from kernel, so it's determistic.
Link: https://lkml.kernel.org/r/20250912013711.3002969-4-chuhu@redhat.com
Fixes: cc92882ee2 ("mm: drop hugetlb_get_unmapped_area{_*} functions")
Signed-off-by: Chunyu Hu <chuhu@redhat.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ca7eada62 ]
When do_task() exhausts its iteration budget (!ret), it sets the state
to TASK_STATE_IDLE to reschedule, without a secondary check on the
current task->state. This can overwrite the TASK_STATE_DRAINING state
set by a concurrent call to rxe_cleanup_task() or rxe_disable_task().
While state changes are protected by a spinlock, both rxe_cleanup_task()
and rxe_disable_task() release the lock while waiting for the task to
finish draining in the while(!is_done(task)) loop. The race occurs if
do_task() hits its iteration limit and acquires the lock in this window.
The cleanup logic may then proceed while the task incorrectly
reschedules itself, leading to a potential use-after-free.
This bug was introduced during the migration from tasklets to workqueues,
where the special handling for the draining case was lost.
Fix this by restoring the original pre-migration behavior. If the state is
TASK_STATE_DRAINING when iterations are exhausted, set cont to 1 to
force a new loop iteration. This allows the task to finish its work, so
that a subsequent iteration can reach the switch statement and correctly
transition the state to TASK_STATE_DRAINED, stopping the task as intended.
Fixes: 9b4b7c1f9f ("RDMA/rxe: Add workqueue support for rxe tasks")
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Gui-Dong Han <hanguidong02@gmail.com>
Link: https://patch.msgid.link/20250919025212.1682087-1-hanguidong02@gmail.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 581e3dea0e ]
On MSM8974 / APQ8074, MSM8226 and MSM8926 the MSS requires loading raw
MBA image instead of the ELF file. Skip the ELF headers if mba.mbn was
specified as the firmware image.
Fixes: a5a4e02d08 ("remoteproc: qcom: Add support for parsing fw dt bindings")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Luca Weiss <luca@lucaweiss.eu> # msm8974pro-fairphone-fp2
Link: https://lore.kernel.org/r/20250706-msm8974-fix-mss-v4-1-630907dbd898@oss.qualcomm.com
[bjorn: Unwrapped the long memcpy line, to taste]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09390ed9af ]
mbox_request_channel() returning value was changed in case of error.
It uses returning value of of_parse_phandle_with_args().
It is returning with -ENOENT instead of -ENODEV when no mboxes property
exists.
Fixes: 24fdd5074b ("mailbox: use error ret code of of_parse_phandle_with_args()")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Stephan Gerhold <stephan.gerhold@linaro.org> # msm8939
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20250725-fix-qcom-smd-v2-1-e4e43613f874@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ca61ed8b3 ]
In ath12k_dp_mon_rx_deliver_msdu(), peer lookup fails because
rxcb->peer_id is not updated with a valid value. This is expected
in monitor mode, where RX frames bypass the regular RX
descriptor path that typically sets rxcb->peer_id.
As a result, the peer is NULL, and link_id and link_valid fields
in the RX status are not populated. This leads to a WARN_ON in
mac80211 when it receives data frame from an associated station
with invalid link_id.
Fix this potential issue by using ppduinfo->peer_id, which holds
the correct peer id for the received frame. This ensures that the
peer is correctly found and the associated link metadata is updated
accordingly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: bd00cc7e8a ("wifi: ath12k: replace the usage of rx desc with rx_info")
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Signed-off-by: Aishwarya R <aishwarya.r@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250724040552.1170642-1-aishwarya.r@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0cafb02de ]
When the initialization of qm->debug.acc_diff_reg fails,
the probe process does not exit. However, after qm->debug.qm_diff_regs is
freed, it is not set to NULL. This can lead to a double free when the
remove process attempts to free it again. Therefore, qm->debug.qm_diff_regs
should be set to NULL after it is freed.
Fixes: 8be0913389 ("crypto: hisilicon/debugfs - Fix debugfs uninit process issue")
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f75f66683d ]
In commit 42d9f6c774 ("crypto: acomp - Move scomp stream allocation
code into acomp"), the crypto_acomp_streams struct was made to rely on
having the alloc_ctx and free_ctx operations defined in the same order
as the scomp_alg struct. But in that same commit, the alloc_ctx and
free_ctx members of scomp_alg may be randomized by structure layout
randomization, since they are contained in a pure ops structure
(containing only function pointers). If the pointers within scomp_alg
are randomized, but those in crypto_acomp_streams are not, then
the order may no longer match. This fixes the problem by removing the
union from scomp_alg so that both crypto_acomp_streams and scomp_alg
will share the same definition of alloc_ctx and free_ctx, ensuring
they will always have the same layout.
Signed-off-by: Dan Moulding <dan@danm.net>
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes: 42d9f6c774 ("crypto: acomp - Move scomp stream allocation code into acomp")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acb59a4bb8 ]
host_seq_bmp is allocated with vzalloc but is currently freed with
bitmap_free, which uses kfree internally. This mismach prevents the
resource from being released properly and may result in memory leaks
or other issues.
Fix this by freeing host_seq_bmp with vfree to match the vzalloc
allocation.
Fixes: f232836a91 ("vfio/pds: Add support for dirty page tracking")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://lore.kernel.org/r/20250913153154.1028835-1-zilin@seu.edu.cn
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 936fb51275 ]
The referenced commit introduced exception handlers on user-space memory
references in copy_from_user and copy_to_user. These handlers return from
the respective function and calculate the remaining bytes left to copy
using the current register contents. This commit fixes a couple of bad
calculations. This will fix the return value of copy_from_user and
copy_to_user in the faulting case. The behaviour of memcpy stays unchanged.
Fixes: 34060b8fff ("arch/sparc: Add accurate exception reporting in M7memcpy")
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> # on Oracle SPARC S7
Tested-by: Tony Rodriguez <unixpro1970@gmail.com> # S7, see https://lore.kernel.org/r/98564e2e68df2dda0e00c67a75c7f7dfedb33c7e.camel@physik.fu-berlin.de
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20250905-memcpy_series-v4-5-1ca72dda195b@mkarcher.dialup.fu-berlin.de
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a746c1a2c ]
The referenced commit introduced exception handlers on user-space memory
references in copy_from_user and copy_to_user. These handlers return from
the respective function and calculate the remaining bytes left to copy
using the current register contents. This commit fixes a bad calculation.
This will fix the return value of copy_to_user in a specific faulting case.
The behaviour of memcpy stays unchanged.
Fixes: 9570770480 ("sparc64: Convert NG4copy_{from,to}_user to accurate exception reporting.")
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> # on Oracle SPARC T4-1
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20250905-memcpy_series-v4-4-1ca72dda195b@mkarcher.dialup.fu-berlin.de
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b67c8fc10 ]
The referenced commit introduced exception handlers on user-space memory
references in copy_from_user and copy_to_user. These handlers return from
the respective function and calculate the remaining bytes left to copy
using the current register contents. This commit fixes a couple of bad
calculations and a broken epilogue in the exception handlers. This will
prevent crashes and ensure correct return values of copy_from_user and
copy_to_user in the faulting case. The behaviour of memcpy stays unchanged.
Fixes: 7ae3aaf53f ("sparc64: Convert NGcopy_{from,to}_user to accurate exception reporting.")
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> # on SPARC T4 with modified kernel to use Niagara 1 code
Tested-by: Magnus Lindholm <linmag7@gmail.com> # on Sun Fire T2000
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Tested-by: Ethan Hawke <ehawk@ember.systems> # on Sun Fire T2000
Tested-by: Ken Link <iissmart@numberzero.org> # on Sun Fire T1000
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20250905-memcpy_series-v4-3-1ca72dda195b@mkarcher.dialup.fu-berlin.de
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47b49c06eb ]
Anthony Yznaga tracked down that a BUG_ON in ext4 code with large folios
enabled resulted from copy_from_user() returning impossibly large values
greater than the size to be copied. This lead to __copy_from_iter()
returning impossible values instead of the actual number of bytes it was
able to copy.
The BUG_ON has been reported in
https://lore.kernel.org/r/b14f55642207e63e907965e209f6323a0df6dcee.camel@physik.fu-berlin.de
The referenced commit introduced exception handlers on user-space memory
references in copy_from_user and copy_to_user. These handlers return from
the respective function and calculate the remaining bytes left to copy
using the current register contents. The exception handlers expect that
%o2 has already been masked during the bulk copy loop, but the masking was
performed after that loop. This will fix the return value of copy_from_user
and copy_to_user in the faulting case. The behaviour of memcpy stays
unchanged.
Fixes: ee841d0aff ("sparc64: Convert U3copy_{from,to}_user to accurate exception reporting.")
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> # on Sun Netra 240
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Tested-by: René Rebe <rene@exactcode.com> # on UltraSparc III+ and UltraSparc IIIi
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20250905-memcpy_series-v4-2-1ca72dda195b@mkarcher.dialup.fu-berlin.de
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fba171300 ]
The referenced commit introduced exception handlers on user-space memory
references in copy_from_user and copy_to_user. These handlers return from
the respective function and calculate the remaining bytes left to copy
using the current register contents. This commit fixes a couple of bad
calculations. This will fix the return value of copy_from_user and
copy_to_user in the faulting case. The behaviour of memcpy stays unchanged.
Fixes: cb736fdbb2 ("sparc64: Convert U1copy_{from,to}_user to accurate exception reporting.")
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> # on QEMU 10.0.3
Tested-by: René Rebe <rene@exactcode.com> # on Ultra 5 UltraSparc IIi
Tested-by: Jonathan 'theJPster' Pallant <kernel@thejpster.org.uk> # on Sun Netra T1
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Link: https://lore.kernel.org/r/20250905-memcpy_series-v4-1-1ca72dda195b@mkarcher.dialup.fu-berlin.de
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87cab86925 ]
In create_sdw_dailink() check that sof_end->codec_info->add_sidecar
is not NULL before calling it.
The original code assumed that if include_sidecar is true, the codec
on that link has an add_sidecar callback. But there could be other
codecs on the same link that do not have an add_sidecar callback.
Fixes: da52441802 ("ASoC: Intel: sof_sdw: Add callbacks to register sidecar devices")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250919140235.1071941-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32d340ae67 ]
In ieee80211_rx_handle_packet(), if the caller does not provide pubsta
information, an attempt is made to find the station using the address 2
(source address) field in the header. Since pubsta is missing, link
information such as link_valid and link_id is also unavailable. Now if such
a situation comes, and if a matching ML station entry is found based on
the source address, currently the packet is dropped due to missing link ID
in the status field which is not correct.
Hence, to fix this issue, if link_valid is not set and the station is an
ML station, make an attempt to find a link station entry using the source
address. If a valid link station is found, derive the link ID and proceed
with packet processing. Otherwise, drop the packet as per the existing
flow.
Fixes: ea9d807b56 ("wifi: mac80211: add link information in ieee80211_rx_status")
Suggested-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250917-fix_data_packet_rx_with_mlo_and_no_pubsta-v1-1-8cf971a958ac@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51a73f1b2e ]
Commit e57b7d62a1 ("wifi: ath10k: poll service ready message before
failing") works around the failure in waiting for the service ready
message by active polling. Note the polling is triggered after initial
wait timeout, which means that the wait-till-timeout can not be avoided
even the message is ready.
A possible fix is to do polling once before wait as well, however this
can not handle the race that the message arrives right after polling.
So the solution is to do periodic polling until timeout.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00309-QCARMSWPZ-1
Fixes: e57b7d62a1 ("wifi: ath10k: poll service ready message before failing")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/all/97a15967-5518-4731-a8ff-d43ff7f437b0@molgen.mpg.de
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250811-ath10k-avoid-unnecessary-wait-v1-1-db2deb87c39b@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43746f13fe ]
ATH12K_DBG_AHB is used for CE logging which is not proper. Add
ATH12K_DBG_CE and replace ATH12K_DBG_AHB with it.
Compile tested only.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250815-ath-dont-warn-on-ce-enqueue-fail-v1-2-f955ddc3ba7a@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26f8fc0b24 ]
Currently, ath12k_dp_rx_h_ppdu() determines the band and frequency
based on the channel number and center frequency from the RX descriptor's
PHY metadata. However, in rare cases, it is observed that frequency
retrieved from the metadata may be invalid or unexpected especially for
6 GHz frames.
This can result in a NULL sband, which prevents proper frequency assignment
in rx_status and potentially leading to incorrect RX packet classification.
To fix this potential issue, add a fallback mechanism that uses
ar->rx_channel to populate the band and frequency when the derived
sband is invalid or missing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vinith Kumar R <quic_vinithku@quicinc.com>
Signed-off-by: Vinith Kumar R <quic_vinithku@quicinc.com>
Signed-off-by: Aishwarya R <aishwarya.r@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250723190651.699828-1-aishwarya.r@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
