commit 49bd7b0814 upstream.
Byte mask for channel-1 of stream-1 is not getting enabled and this
causes failures during AMX use cases. This happens because the byte
map value 0 matches the byte map array and put() callback returns
without enabling the corresponding bits in the byte mask.
AMX supports 4 input streams and each stream can take a maximum of
16 channels. Each byte in the output frame is uniquely mapped to a
byte in one of these 4 inputs. This mapping is done with the help of
byte map array via user space control setting. The byte map array
size in the driver is 16 and each array element is of size 4 bytes.
This corresponds to 64 byte map values.
Each byte in the byte map array can have any value between 0 to 255
to enable the corresponding bits in the byte mask. The value 256 is
used as a way to disable the byte map. However the byte map array
element cannot store this value. The put() callback disables the byte
mask for 256 value and byte map value is reset to 0 for this case.
This causes problems during subsequent runs since put() callback,
for value of 0, just returns without enabling the byte mask. In short,
the problem is coming because 0 and 256 control values are stored as
0 in the byte map array.
Right now fix the put() callback by actually looking at the byte mask
array state to identify if any change is needed and update the fields
accordingly. The get() callback needs an update as well to return the
correct control value that user has set before. Note that when user
sets 256, the value is stored as 0 and byte mask is disabled. So byte
mask state is used to either return 256 or the value from byte map
array.
Given above, this looks bit complicated and all this happens because
the byte map array is tightly packed and cannot actually store the 256
value. Right now the priority is to fix the existing failure and a TODO
item is put to improve this logic.
Fixes: 8db78ace1b ("ASoC: tegra: Fix kcontrol put callback in AMX")
Cc: stable@vger.kernel.org
Signed-off-by: Sheetal <sheetal@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1688015537-31682-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5475829ad upstream.
The MBHC resources must be released on component probe failure and
removal so can not be tied to the lifetime of the component device.
This is specifically needed to allow probe deferrals of the sound card
which otherwise fails when reprobing the codec component:
snd-sc8280xp sound: ASoC: failed to instantiate card -517
genirq: Flags mismatch irq 299. 00002001 (mbhc sw intr) vs. 00002001 (mbhc sw intr)
wcd938x_codec audio-codec: Failed to request mbhc interrupts -16
wcd938x_codec audio-codec: mbhc initialization failed
wcd938x_codec audio-codec: ASoC: error at snd_soc_component_probe on audio-codec: -16
snd-sc8280xp sound: ASoC: failed to instantiate card -16
Fixes: 0e5c9e7ff8 ("ASoC: codecs: wcd: add multi button Headset detection support")
Cc: stable@vger.kernel.org # 5.14
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230705123018.30903-7-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9ba2975e9 upstream.
After commit 6085f9e6dc ("ASoC: cs35l45: IRQ support"), without any
other configuration that selects CONFIG_REGMAP_IRQ, modpost errors out
with:
ERROR: modpost: "regmap_irq_get_virq" [sound/soc/codecs/snd-soc-cs35l45.ko] undefined!
ERROR: modpost: "devm_regmap_add_irq_chip" [sound/soc/codecs/snd-soc-cs35l45.ko] undefined!
Add the Kconfig selection to ensure these functions get built and
included, which resolves the build failure.
Cc: stable@vger.kernel.org
Fixes: 6085f9e6dc ("ASoC: cs35l45: IRQ support")
Reported-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Closes: https://github.com/ClangBuiltLinux/linux/issues/1882
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230703-cs35l45-select-regmap_irq-v1-1-37d7e838b614@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e51df4f81b upstream.
In commit 2cb1e0259f ("ASoC: cs42l51: re-hook of_match_table
pointer"), 9 years ago, some random guy fixed the cs42l51 after it was
split into a core part and an I2C part to properly match based on a
Device Tree compatible string.
However, the fix in this commit is wrong: the MODULE_DEVICE_TABLE(of,
....) is in the core part of the driver, not the I2C part. Therefore,
automatic module loading based on module.alias, based on matching with
the DT compatible string, loads the core part of the driver, but not
the I2C part. And threfore, the i2c_driver is not registered, and the
codec is not known to the system, nor matched with a DT node with the
corresponding compatible string.
In order to fix that, we move the MODULE_DEVICE_TABLE(of, ...) into
the I2C part of the driver. The cs42l51_of_match[] array is also moved
as well, as it is not possible to have this definition in one file,
and the MODULE_DEVICE_TABLE(of, ...) invocation in another file, due
to how MODULE_DEVICE_TABLE works.
Thanks to this commit, the I2C part of the driver now properly
autoloads, and thanks to its dependency on the core part, the core
part gets autoloaded as well, resulting in a functional sound card
without having to manually load kernel modules.
Fixes: 2cb1e0259f ("ASoC: cs42l51: re-hook of_match_table pointer")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Link: https://lore.kernel.org/r/20230713112112.778576-1-thomas.petazzoni@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70a6404ff6 upstream.
Following prints are observed while testing audio on Jetson AGX Orin which
has onboard RT5640 audio codec:
BUG: sleeping function called from invalid context at kernel/workqueue.c:3027
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0
preempt_count: 10001, expected: 0
RCU nest depth: 0, expected: 0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1e0/0x270
---[ end trace ad1c64905aac14a6 ]-
The IRQ handler rt5640_irq() runs in interrupt context and can sleep
during cancel_delayed_work_sync().
Fix this by running IRQ handler, rt5640_irq(), in thread context.
Hence replace request_irq() calls with devm_request_threaded_irq().
Fixes: 051dade346 ("ASoC: rt5640: Fix the wrong state of JD1 and JD2")
Cc: stable@vger.kernel.org
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1688015537-31682-4-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dfe70be0b upstream.
Byte mask for channel-1 of stream-1 is not getting enabled and this
causes failures during ADX use cases. This happens because the byte
map value 0 matches the byte map array and put() callback returns
without enabling the corresponding bits in the byte mask.
ADX supports 4 output streams and each stream can have a maximum of
16 channels. Each byte in the input frame is uniquely mapped to a
byte in one of these 4 outputs. This mapping is done with the help of
byte map array via user space control setting. The byte map array
size in the driver is 16 and each array element is of size 4 bytes.
This corresponds to 64 byte map values.
Each byte in the byte map array can have any value between 0 to 255
to enable the corresponding bits in the byte mask. The value 256 is
used as a way to disable the byte map. However the byte map array
element cannot store this value. The put() callback disables the byte
mask for 256 value and byte map value is reset to 0 for this case.
This causes problems during subsequent runs since put() callback,
for value of 0, just returns without enabling the byte mask. In short,
the problem is coming because 0 and 256 control values are stored as
0 in the byte map array.
Right now fix the put() callback by actually looking at the byte mask
array state to identify if any change is needed and update the fields
accordingly. The get() callback needs an update as well to return the
correct control value that user has set before. Note that when user
set 256, the value is stored as 0 and byte mask is disabled. So byte
mask state is used to either return 256 or the value from byte map
array.
Given above, this looks bit complicated and all this happens because
the byte map array is tightly packed and cannot actually store the 256
value. Right now the priority is to fix the existing failure and a TODO
item is put to improve this logic.
Fixes: 3c97881b8c ("ASoC: tegra: Fix kcontrol put callback in ADX")
Cc: stable@vger.kernel.org
Signed-off-by: Sheetal <sheetal@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1688015537-31682-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86867aca73 upstream.
This reverts commit ff87d619ac.
Andreas reports that on an i.MX8MP-based system where MCLK needs to be
used as an input, the MCLK pin is actually an output, despite not having
the 'fsl,sai-mclk-direction-output' property present in the devicetree.
This is caused by commit ff87d619ac ("ASoC: fsl_sai: Enable
MCTL_MCLK_EN bit for master mode") that sets FSL_SAI_MCTL_MCLK_EN
unconditionally for imx8mm/8mn/8mp/93, causing the MCLK to always
be configured as output.
FSL_SAI_MCTL_MCLK_EN corresponds to the MOE (MCLK Output Enable) bit
of register MCR and the drivers sets it when the
'fsl,sai-mclk-direction-output' devicetree property is present.
Revert the commit to allow SAI to use MCLK as input as well.
Cc: stable@vger.kernel.org
Fixes: ff87d619ac ("ASoC: fsl_sai: Enable MCTL_MCLK_EN bit for master mode")
Reported-by: Andreas Henriksson <andreas@fatal.se>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230706221827.1938990-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 269f399dc1 upstream.
Otherwise bit clock remains running writing invalid data to the DAC.
Signed-off-by: Matus Gajdos <matuszpd@gmail.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230712124934.32232-1-matuszpd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2387ccf43e upstream.
[Why & How]
Port of a change that went into DCN314 to keep the PHY enabled
when we have a connected and active DP display.
The PHY can hang if PHY refclk is disabled inadvertently.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a25cefc09 upstream.
[Why & How]
If there is no TG allocation we can dereference a NULL pointer when
checking if the TG is enabled.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a460beefe7 upstream.
[WHY]
All of pipes will be used when the MPC split enable on the dcn
which just has 2 pipes. Then MPO enter will trigger the minimal
transition which need programe dcn from 2 pipes MPC split to 2
pipes MPO. This action will cause lag if happen frequently.
[HOW]
Disable the MPC split for the platform which dcn resource is limited
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ca67aba8d upstream.
Up until now, amdgpu was silently degrading to vsync when
user-space requested an async flip but the hardware didn't support
it.
The hardware doesn't support immediate flips when the update changes
the FB pitch, the DCC state, the rotation, enables or disables CRTCs
or planes, etc. This is reflected in the dm_crtc_state.update_type
field: UPDATE_TYPE_FAST means that immediate flip is supported.
Silently degrading async flips to vsync is not the expected behavior
from a uAPI point-of-view. Xorg expects async flips to fail if
unsupported, to be able to fall back to a blit. i915 already behaves
this way.
This patch aligns amdgpu with uAPI expectations and returns a failure
when an async flip is not possible.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2329cc7a10 upstream.
When a new mode is set to modeset->mode, the previous mode should be freed.
This fixes the following kmemleak report:
drm_mode_duplicate+0x45/0x220 [drm]
drm_client_modeset_probe+0x944/0xf50 [drm]
__drm_fb_helper_initial_config_and_unlock+0xb4/0x2c0 [drm_kms_helper]
drm_fbdev_client_hotplug+0x2bc/0x4d0 [drm_kms_helper]
drm_client_register+0x169/0x240 [drm]
ast_pci_probe+0x142/0x190 [ast]
local_pci_probe+0xdc/0x180
work_for_cpu_fn+0x4e/0xa0
process_one_work+0x8b7/0x1540
worker_thread+0x70a/0xed0
kthread+0x29f/0x340
ret_from_fork+0x1f/0x30
cc: <stable@vger.kernel.org>
Reported-by: Zhang Yi <yizhan@redhat.com>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230711092203.68157-3-jfalempe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 752a281032 upstream.
This was completely bogus before, using maximum DCB device index rather
than maximum AUX ID to size the buffer that stores event refcounts.
*Pretty* unlikely to have been an actual problem on most configurations,
that is, unless you've got one of the rare boards that have off-chip DP.
There, it'll likely crash.
Cc: stable@vger.kernel.org # 6.4+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230719044051.6975-1-skeggsb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 068c8bb10f upstream.
Use current uclk to be consistent with other dGPUs.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4eb118241 upstream.
Use average gfxclock for consistency with other dGPUs.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b42ae87a7b upstream.
In below thousands of screen rotation loop tests with virtual display
enabled, a CPU hard lockup issue may happen, leading system to unresponsive
and crash.
do {
xrandr --output Virtual --rotate inverted
xrandr --output Virtual --rotate right
xrandr --output Virtual --rotate left
xrandr --output Virtual --rotate normal
} while (1);
NMI watchdog: Watchdog detected hard LOCKUP on cpu 1
? hrtimer_run_softirq+0x140/0x140
? store_vblank+0xe0/0xe0 [drm]
hrtimer_cancel+0x15/0x30
amdgpu_vkms_disable_vblank+0x15/0x30 [amdgpu]
drm_vblank_disable_and_save+0x185/0x1f0 [drm]
drm_crtc_vblank_off+0x159/0x4c0 [drm]
? record_print_text.cold+0x11/0x11
? wait_for_completion_timeout+0x232/0x280
? drm_crtc_wait_one_vblank+0x40/0x40 [drm]
? bit_wait_io_timeout+0xe0/0xe0
? wait_for_completion_interruptible+0x1d7/0x320
? mutex_unlock+0x81/0xd0
amdgpu_vkms_crtc_atomic_disable
It's caused by a stuck in lock dependency in such scenario on different
CPUs.
CPU1 CPU2
drm_crtc_vblank_off hrtimer_interrupt
grab event_lock (irq disabled) __hrtimer_run_queues
grab vbl_lock/vblank_time_block amdgpu_vkms_vblank_simulate
amdgpu_vkms_disable_vblank drm_handle_vblank
hrtimer_cancel grab dev->event_lock
So CPU1 stucks in hrtimer_cancel as timer callback is running endless on
current clock base, as that timer queue on CPU2 has no chance to finish it
because of failing to hold the lock. So NMI watchdog will throw the errors
after its threshold, and all later CPUs are impacted/blocked.
So use hrtimer_try_to_cancel to fix this, as disable_vblank callback
does not need to wait the handler to finish. And also it's not necessary
to check the return value of hrtimer_try_to_cancel, because even if it's
-1 which means current timer callback is running, it will be reprogrammed
in hrtimer_start with calling enable_vblank to make it works.
v2: only re-arm timer when vblank is enabled (Christian) and add a Fixes
tag as well
v3: drop warn printing (Christian)
v4: drop superfluous check of blank->enabled in timer function, as it's
guaranteed in drm_handle_vblank (Christian)
Fixes: 84ec374bd5 ("drm/amdgpu: create amdgpu_vkms (v4)")
Cc: stable@vger.kernel.org
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05abb3be91 upstream.
Currently dma_resv_get_fences() will leak the previously
allocated array if the fence iteration got restarted and
the krealloc_array() fails.
Free the old array by hand, and make sure we still clear
the returned *fences so the caller won't end up accessing
freed memory. Some (but not all) of the callers of
dma_resv_get_fences() seem to still trawl through the
array even when dma_resv_get_fences() failed. And let's
zero out *num_fences as well for good measure.
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Christian König <christian.koenig@amd.com>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Fixes: d3c80698c9 ("dma-buf: use new iterator in dma_resv_get_fences v3")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20230713194745.1751-1-ville.syrjala@linux.intel.com
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47d87f71d0 upstream.
The encode_dma() function has integer overflow checks. The
encode_passthrough(), encode_activate() and encode_status() functions
did not. I added integer overflow checking everywhere. I also
updated the integer overflow checking in encode_dma() to use size_add()
so everything is consistent.
Fixes: 129776ac2e ("accel/qaic: Add control path")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Cc: stable@vger.kernel.org # 6.4.x
[jhugo: tweak if in encode_dma() to match existing style]
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZK0Q7IsPkj6WSCcL@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51b56382ed upstream.
Copy the bounds checking from encode_message() to decode_message().
This patch addresses the following concerns. Ensure that there is
enough space for at least one header so that we don't have a negative
size later.
if (msg_hdr_len < sizeof(*trans_hdr))
Ensure that we have enough space to read the next header from the
msg->data.
if (msg_len > msg_hdr_len - sizeof(*trans_hdr))
return -EINVAL;
Check that the trans_hdr->len is not below the minimum size:
if (hdr_len < sizeof(*trans_hdr))
This minimum check ensures that we don't corrupt memory in
decode_passthrough() when we do.
memcpy(out_trans->data, in_trans->data, len - sizeof(in_trans->hdr));
And finally, use size_add() to prevent an integer overflow:
if (size_add(msg_len, hdr_len) > msg_hdr_len)
Fixes: 129776ac2e ("accel/qaic: Add control path")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Cc: stable@vger.kernel.org # 6.4.x
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZK0Q5nbLyDO7kJa+@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea33cb6fc2 upstream.
There are several issues in this code. The check at the start of the
loop:
if (user_len >= user_msg->len) {
This check does not ensure that we have enough space for the trans_hdr
(8 bytes). Instead the check needs to be:
if (user_len > user_msg->len - sizeof(*trans_hdr)) {
That subtraction is done as an unsigned long we want to avoid
negatives. Add a lower bound to the start of the function.
if (user_msg->len < sizeof(*trans_hdr))
There is a second integer underflow which can happen if
trans_hdr->len is zero inside the encode_passthrough() function.
memcpy(out_trans->data, in_trans->data, in_trans->hdr.len - sizeof(in_trans->hdr));
Instead of adding a check to encode_passthrough() it's better to check
in this central place. Add that check:
if (trans_hdr->len < sizeof(trans_hdr)
The final concern is that the "user_len + trans_hdr->len" might have an
integer overflow bug. Use size_add() to prevent that.
- if (user_len + trans_hdr->len > user_msg->len) {
+ if (size_add(user_len, trans_hdr->len) > user_msg->len) {
Fixes: 129776ac2e ("accel/qaic: Add control path")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Cc: stable@vger.kernel.org # 6.4.x
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9a0cb0c1-a974-4f10-bc8d-94437983639a@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 031c99e71f upstream.
When looking at the TC selftest reports, I noticed one test was failing
because /proc/net/nf_conntrack was not available.
not ok 373 3992 - Add ct action triggering DNAT tuple conflict
Could not match regex pattern. Verify command output:
cat: /proc/net/nf_conntrack: No such file or directory
It is only available if NF_CONNTRACK_PROCFS kconfig is set. So the issue
can be fixed simply by adding it to the list of required kconfig.
Fixes: e469056413 ("tc-testing: add test for ct DNAT tuple collision")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/netdev/0e061d4a-9a23-9f58-3b35-d8919de332d7@tessares.net/T/ [1]
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Tested-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20230713-tc-selftests-lkft-v1-3-1eb4fd3a96e7@tessares.net
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5886e4d5ec upstream.
If the gs_usb device driver is unloaded (or unbound) before the
interface is shut down, the USB stack first calls the struct
usb_driver::disconnect and then the struct net_device_ops::ndo_stop
callback.
In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more
RX'ed CAN frames are send from the USB device to the host. Later in
gs_can_close() a reset control message is send to each CAN channel to
remove the controller from the CAN bus. In this race window the USB
device can still receive CAN frames from the bus and internally queue
them to be send to the host.
At least in the current version of the candlelight firmware, the queue
of received CAN frames is not emptied during the reset command. After
loading (or binding) the gs_usb driver, new URBs are submitted during
the struct net_device_ops::ndo_open callback and the candlelight
firmware starts sending its already queued CAN frames to the host.
However, this scenario was not considered when implementing the
hardware timestamp function. The cycle counter/time counter
infrastructure is set up (gs_usb_timestamp_init()) after the USBs are
submitted, resulting in a NULL pointer dereference if
timecounter_cyc2time() (via the call chain:
gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() ->
gs_usb_skb_set_timestamp()) is called too early.
Move the gs_usb_timestamp_init() function before the URBs are
submitted to fix this problem.
For a comprehensive solution, we need to consider gs_usb devices with
more than 1 channel. The cycle counter/time counter infrastructure is
setup per channel, but the RX URBs are per device. Once gs_can_open()
of _a_ channel has been called, and URBs have been submitted, the
gs_usb_receive_bulk_callback() can be called for _all_ available
channels, even for channels that are not running, yet. As cycle
counter/time counter has not set up, this will again lead to a NULL
pointer dereference.
Convert the cycle counter/time counter from a "per channel" to a "per
device" functionality. Also set it up, before submitting any URBs to
the device.
Further in gs_usb_receive_bulk_callback(), don't process any URBs for
not started CAN channels, only resubmit the URB.
Fixes: 45dfa45f52 ("can: gs_usb: add RX and TX hardware timestamp support")
Closes: https://github.com/candle-usb/candleLight_fw/issues/137#issuecomment-1623532076
Cc: stable@vger.kernel.org
Cc: John Whittington <git@jbrengineering.co.uk>
Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-2-9017cefcd9d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2603be9e81 upstream.
The gs_usb driver handles USB devices with more than 1 CAN channel.
The RX path for all channels share the same bulk endpoint (the
transmitted bulk data encodes the channel number). These per-device
resources are allocated and submitted by the first opened channel.
During this allocation, the resources are either released immediately
in case of a failure or the URBs are anchored. All anchored URBs are
finally killed with gs_usb_disconnect().
Currently, gs_can_open() returns with an error if the allocation of a
URB or a buffer fails. However, if usb_submit_urb() fails, the driver
continues with the URBs submitted so far, even if no URBs were
successfully submitted.
Treat every error as fatal and free all allocated resources
immediately.
Switch to goto-style error handling, to prepare the driver for more
per-device resource allocation.
Cc: stable@vger.kernel.org
Cc: John Whittington <git@jbrengineering.co.uk>
Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-1-9017cefcd9d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9efa1a5407 upstream.
The mcp251xfd controller needs an idle bus to enter 'Normal CAN 2.0
mode' or . The maximum length of a CAN frame is 736 bits (64 data
bytes, CAN-FD, EFF mode, worst case bit stuffing and interframe
spacing). For low bit rates like 10 kbit/s the arbitrarily chosen
MCP251XFD_POLL_TIMEOUT_US of 1 ms is too small.
Otherwise during polling for the CAN controller to enter 'Normal CAN
2.0 mode' the timeout limit is exceeded and the configuration fails
with:
| $ ip link set dev can1 up type can bitrate 10000
| [ 731.911072] mcp251xfd spi2.1 can1: Controller failed to enter mode CAN 2.0 Mode (6) and stays in Configuration Mode (4) (con=0x068b0760, osc=0x00000468).
| [ 731.927192] mcp251xfd spi2.1 can1: CRC read error at address 0x0e0c (length=4, data=00 00 00 00, CRC=0x0000) retrying.
| [ 731.938101] A link change request failed with some changes committed already. Interface can1 may have been left with an inconsistent configuration, please check.
| RTNETLINK answers: Connection timed out
Make MCP251XFD_POLL_TIMEOUT_US timeout calculation dynamic. Use
maximum of 1ms and bit time of 1 full 64 data bytes CAN-FD frame in
EFF mode, worst case bit stuffing and interframe spacing at the
current bit rate.
For easier backporting define the macro MCP251XFD_FRAME_LEN_MAX_BITS
that holds the max frame length in bits, which is 736. This can be
replaced by can_frame_bits(true, true, true, true, CANFD_MAX_DLEN) in
a cleanup patch later.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230717-mcp251xfd-fix-increase-poll-timeout-v5-1-06600f34c684@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4d5be94a8 upstream.
When we reconfigure the SVE vector length we discard the backing storage
for the SVE vectors and then reallocate on next SVE use, leaving the SME
specific state alone. This means that we do not enable SME traps if they
were already disabled. That means that userspace code can enter streaming
mode without trapping, putting the task in a state where if we try to save
the state of the task we will fault.
Since the ABI does not specify that changing the SVE vector length disturbs
SME state, and since SVE code may not be aware of SME code in the process,
we shouldn't simply discard any ZA state. Instead immediately reallocate
the storage for SVE, and disable SME if we change the SVE vector length
while there is no SME state active.
Disabling SME traps on SVE vector length changes would make the overall
code more complex since we would have a state where we have valid SME state
stored but might get a SME trap.
Fixes: 9e4ab6c891 ("arm64/sme: Implement vector length configuration prctl()s")
Reported-by: David Spickett <David.Spickett@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230720-arm64-fix-sve-sme-vl-change-v2-1-8eea06b82d57@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07e981137f upstream.
IA64 is the only architecture which does not consider the pgoff value when
searching for a possible free memory region with vm_unmapped_area().
Adding this seems to have no negative side effect on IA64, so add it now
to make IA64 consistent with all other architectures.
Cc: stable@vger.kernel.org # 6.4
Signed-off-by: Helge Deller <deller@gmx.de>
Tested-by: matoro <matoro_mailinglist_kernel@matoro.tk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-ia64@vger.kernel.org
Link: https://lore.kernel.org/r/20230721152432.196382-3-deller@gmx.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c9d2eb5e9 upstream.
The SMBus I2C buses have limits on the size of transfers they can do but
do not factor in the register length meaning we may try to do a transfer
longer than our length limit, the core will not take care of this.
Future changes will factor this out into the core but there are a number
of users that assume current behaviour so let's just do something
conservative here.
This does not take account padding bits but practically speaking these
are very rarely if ever used on I2C buses given that they generally run
slowly enough to mean there's no issue.
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20230712-regmap-max-transfer-v1-2-80e2aed22e83@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bb8f49cd2 upstream.
Since commit 241d2fb56a ("of: Make OF framebuffer device names unique"),
as spotted by Frédéric Bonnard, the historical "of-display" device is
gone: the updated logic creates "of-display.0" instead, then as many
"of-display.N" as required.
This means that offb no longer finds the expected device, which prevents
the Debian Installer from setting up its interface, at least on ppc64el.
Fix this by keeping "of-display" for the first device and "of-display.N"
for subsequent devices.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217328
Link: https://bugs.debian.org/1033058
Fixes: 241d2fb56a ("of: Make OF framebuffer device names unique")
Cc: stable@vger.kernel.org
Cc: Cyril Brulebois <cyril@debamax.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Helge Deller <deller@gmx.de>
Acked-by: Helge Deller <deller@gmx.de>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Michal Suchánek <msuchanek@suse.de>
Link: https://lore.kernel.org/r/20230710174007.2291013-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cfca532dd upstream.
The length information for available buffer space for CCA
replies is covered with two fields in the T6 header prepended
on each CCA reply: fromcardlen1 and fromcardlen2. The sum of
these both values must not exceed the AP bus limit for this
card (24KB for CEX8, 12KB CEX7 and older) minus the always
present headers.
The current code adjusted the fromcardlen2 value in case
of exceeding the AP bus limit when there was a non-zero
value given from userspace. Some tests now showed that this
was the wrong assumption. Instead the userspace value given for
this field should always be trusted and if the sum of the
two fields exceeds the AP bus limit for this card the first
field fromcardlen1 should be adjusted instead.
So now the calculation is done with this new insight in mind.
Also some additional checks for overflow have been introduced
and some comments to provide some documentation for future
maintainers of this complicated calculation code.
Furthermore the 128 bytes of fix overhead which is used
in the current code is not correct. Investigations showed
that for a reply always the same two header structs are
prepended before a possible payload. So this is also fixed
with this patch.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc64734825 upstream.
When problems were noticed with the register address not being taken
into account when limiting raw transfers with I2C devices we fixed this
in the core. Unfortunately it has subsequently been realised that a lot
of buses were relying on the prior behaviour, partly due to unclear
documentation not making it obvious what was intended in the core. This
is all more involved to fix than is sensible for a fix commit so let's
just drop the original fixes, a separate commit will fix the originally
observed problem in an I2C specific way
Fixes: 3981514180 ("regmap: Account for register length when chunking")
Fixes: c8e796895e ("regmap: spi-avmm: Fix regmap_bus max_raw_write")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Xu Yilun <yilun.xu@intel.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230712-regmap-max-transfer-v1-1-80e2aed22e83@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73274c33d9 upstream.
If get_user_pages_fast() allocates some pages but not as many as we
wanted, then the current code leaks those pages. Call put_page() on
the pages before returning.
Fixes: 129776ac2e ("accel/qaic: Add control path")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dafna Hirschfeld <dhirschfeld@habana.ai>
Cc: stable@vger.kernel.org # 6.4.x
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZK0Q+ZuONTsBG+1T@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b19c98f237 upstream.
Syzbot reported a panic that looks like this:
assertion failed: fs_info->exclusive_operation == BTRFS_EXCLOP_BALANCE_PAUSED, in fs/btrfs/ioctl.c:465
------------[ cut here ]------------
kernel BUG at fs/btrfs/messages.c:259!
RIP: 0010:btrfs_assertfail+0x2c/0x30 fs/btrfs/messages.c:259
Call Trace:
<TASK>
btrfs_exclop_balance fs/btrfs/ioctl.c:465 [inline]
btrfs_ioctl_balance fs/btrfs/ioctl.c:3564 [inline]
btrfs_ioctl+0x531e/0x5b30 fs/btrfs/ioctl.c:4632
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x197/0x210 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The reproducer is running a balance and a cancel or pause in parallel.
The way balance finishes is a bit wonky, if we were paused we need to
save the balance_ctl in the fs_info, but clear it otherwise and cleanup.
However we rely on the return values being specific errors, or having a
cancel request or no pause request. If balance completes and returns 0,
but we have a pause or cancel request we won't do the appropriate
cleanup, and then the next time we try to start a balance we'll trip
this ASSERT.
The error handling is just wrong here, we always want to clean up,
unless we got -ECANCELLED and we set the appropriate pause flag in the
exclusive op. With this patch the reproducer ran for an hour without
tripping, previously it would trip in less than a few minutes.
Reported-by: syzbot+c0f3acf145cb465426d5@syzkaller.appspotmail.com
CC: stable@vger.kernel.org # 6.1+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a567e920f upstream.
Fuse shouldn't return ENOSYS from its ioctl implementation. If userspace
responds with ENOSYS it should be translated to ENOTTY.
There are two ways to return an error from the IOCTL request:
- fuse_out_header.error
- fuse_ioctl_out.result
Commit 02c0cab8e7 ("fuse: ioctl: translate ENOSYS") already fixed this
issue for the first case, but missed the second case. This patch fixes the
second case.
Reported-by: Jonathan Katz <jkatz@eitmlabs.org>
Closes: https://lore.kernel.org/all/CALKgVmcC1VUV_gJVq70n--omMJZUb4HSh_FqvLTHgNBc+HCLFQ@mail.gmail.com/
Fixes: 02c0cab8e7 ("fuse: ioctl: translate ENOSYS")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1a07c2b4e upstream.
At exclude_super_stripes(), if we happen to find a block group that has
super blocks mapped to it and we are on a zoned filesystem, we error out
as this is not supposed to happen, indicating either a bug or maybe some
memory corruption for example. However we are exiting the function without
freeing the memory allocated for the logical address of the super blocks.
Fix this by freeing the logical address.
Fixes: 12659251ca ("btrfs: implement log-structured superblock for ZONED mode")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b777d279ff upstream.
At btrfs_orphan_cleanup(), if we were able to find the inode, we do an
iput() on the inode, then if btrfs_drop_verity_items() succeeds and then
either btrfs_start_transaction() or btrfs_del_orphan_item() fail, we do
another iput() in the respective error paths, resulting in an extra iput()
on the inode.
Fix this by setting inode to NULL after the first iput(), as iput()
ignores a NULL inode pointer argument.
Fixes: a13bb2c038 ("btrfs: add missing iputs on orphan cleanup failure")
CC: stable@vger.kernel.org # 6.4
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17b17fcd6d upstream.
While trying to get the subpage blocksize tests running, I hit the
following panic on generic/476
assertion failed: PagePrivate(page) && page->private, in fs/btrfs/subpage.c:229
kernel BUG at fs/btrfs/subpage.c:229!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
CPU: 1 PID: 1453 Comm: fsstress Not tainted 6.4.0-rc7+ #12
Hardware name: QEMU KVM Virtual Machine, BIOS edk2-20230301gitf80f052277c8-26.fc38 03/01/2023
pstate: 61400005 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
pc : btrfs_subpage_assert+0xbc/0xf0
lr : btrfs_subpage_assert+0xbc/0xf0
Call trace:
btrfs_subpage_assert+0xbc/0xf0
btrfs_subpage_clear_checked+0x38/0xc0
btrfs_page_clear_checked+0x48/0x98
btrfs_truncate_block+0x5d0/0x6a8
btrfs_cont_expand+0x5c/0x528
btrfs_write_check.isra.0+0xf8/0x150
btrfs_buffered_write+0xb4/0x760
btrfs_do_write_iter+0x2f8/0x4b0
btrfs_file_write_iter+0x1c/0x30
do_iter_readv_writev+0xc8/0x158
do_iter_write+0x9c/0x210
vfs_iter_write+0x24/0x40
iter_file_splice_write+0x224/0x390
direct_splice_actor+0x38/0x68
splice_direct_to_actor+0x12c/0x260
do_splice_direct+0x90/0xe8
generic_copy_file_range+0x50/0x90
vfs_copy_file_range+0x29c/0x470
__arm64_sys_copy_file_range+0xcc/0x498
invoke_syscall.constprop.0+0x80/0xd8
do_el0_svc+0x6c/0x168
el0_svc+0x50/0x1b0
el0t_64_sync_handler+0x114/0x120
el0t_64_sync+0x194/0x198
This happens because during btrfs_cont_expand we'll get a page, set it
as mapped, and if it's not Uptodate we'll read it. However between the
read and re-locking the page we could have called release_folio() on the
page, but left the page in the file mapping. release_folio() can clear
the page private, and thus further down we blow up when we go to modify
the subpage bits.
Fix this by putting the set_page_extent_mapped() after the read. This
is safe because read_folio() will call set_page_extent_mapped() before
it does the read, and then if we clear page private but leave it on the
mapping we're completely safe re-setting set_page_extent_mapped(). With
this patch I can now run generic/476 without panicing.
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 486c737f7f upstream.
[REGRESSION]
Commit 75b4703329 ("btrfs: raid56: migrate recovery and scrub recovery
path to use error_bitmap") changed the behavior of scrub_rbio().
Initially if we have no error reading the raid bio, we will assign
@need_check to true, then finish_parity_scrub() would later verify the
content of P/Q stripes before writeback.
But after that commit we never verify the content of P/Q stripes and
just writeback them.
This can lead to unrepaired P/Q stripes during scrub, or already
corrupted P/Q copied to the dev-replace target.
[FIX]
The situation is more complex than the regression, in fact the initial
behavior is not 100% correct either.
If we have the following rare case, it can still lead to the same
problem using the old behavior:
0 16K 32K 48K 64K
Data 1: |IIIIIII| |
Data 2: | |
Parity: | |CCCCCCC| |
Where "I" means IO error, "C" means corruption.
In the above case, we're scrubbing the parity stripe, then read out all
the contents of Data 1, Data 2, Parity stripes.
But found IO error in Data 1, which leads to rebuild using Data 2 and
Parity and got the correct data.
In that case, we would not verify if the Parity is correct for range
[16K, 32K).
So here we have to always verify the content of Parity no matter if we
did recovery or not.
This patch would remove the @need_check parameter of
finish_parity_scrub() completely, and would always do the P/Q
verification before writeback.
Fixes: 75b4703329 ("btrfs: raid56: migrate recovery and scrub recovery path to use error_bitmap")
CC: stable@vger.kernel.org # 6.2+
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3066ff9347 upstream.
This is just a safety precaution to avoid checking flags on memory that was
initialized on the user space side. libfuse zeroes struct fuse_init_out
outarg, but this is not guranteed to be done in all implementations.
Better is to act on flags and to only apply flags2 when FUSE_INIT_EXT is
set.
There is a risk with this change, though - it might break existing user
space libraries, which are already using flags2 without setting
FUSE_INIT_EXT.
The corresponding libfuse patch is here
https://github.com/libfuse/libfuse/pull/662
Signed-off-by: Bernd Schubert <bschubert@ddn.com>
Fixes: 53db28933e ("fuse: extend init flags")
Cc: <stable@vger.kernel.org> # v5.17
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cadfbd5a1 upstream.
Add an init flag idicating whether the FUSE_EXPIRE_ONLY flag of
FUSE_NOTIFY_INVAL_ENTRY is effective.
This is needed for backports of this feature, otherwise the server could
just check the protocol version.
Fixes: 4f8d37020e ("fuse: add "expire only" mode to FUSE_NOTIFY_INVAL_ENTRY")
Cc: <stable@vger.kernel.org> # v6.2
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9d1c4c6df upstream.
If the LOOKUP request triggered from fuse_dentry_revalidate() is
interrupted, then the dentry will be invalidated, possibly resulting in
submounts being unmounted.
Reported-by: Xu Rongbo <xurongbo@baidu.com>
Closes: https://lore.kernel.org/all/CAJfpegswN_CJJ6C3RZiaK6rpFmNyWmXfaEpnQUJ42KCwNF5tWw@mail.gmail.com/
Fixes: 9e6268db49 ("[PATCH] FUSE - read-write operations")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
