The new Qualcomm QDU1000 and QRU1000 platforms, and the IDP device on
these are introduced. New support for a couple of USB modem sticks from
THWC are introduced, so is support for Xiaomi Mi Pad 5 Pro and the Pro
SKU of the Herobrine device.
The Core Bus Fabric (CBF) is introduced on MSM8996. Interconnect paths
for UFS are also described.
A few fixes related to the power-grid of herobrine, on SC7280, are
introduced.
QFPROM is introduced on IPQ8074 and Interconnect providers are added for
SDM670.
On SDM845 the duplicated wcd9340 audio coded description is moved from
devices to a common file, audio devices are added to the OnePlus 6 and
6T.
On SM6115 debug UART, SMP2P, watchdog nodes are introduced, and the
platform is switched to use #address/size-cells of 2, in line with most
other platforms.
Camera control interface and clock controllers are added for SM6350, and
the CCI interface is enabled on the Fairphone FP4.
On SM8350 the interconnect reference of SDHCI controller is corrected,
DSI1 PHY clocks are properly described as sources for the Display clock
controller and DSI1 is wired up to the display controller.
The firmware paths are corrected for the Sony Xperia Nagara platform.
The GPR bus, audio servic3es and LPASS pinctrl nodes are added for the
SM8550 platform. Additionally a few small typos/errors are corrected.
gpio-ranges are corrected across MSM8953, SM6115 and SC8280XP and a
range of DT validation issues are corrected.
-----BEGIN PGP SIGNATURE-----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=wSbI
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=nzqV
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
More Qualcomm ARM64 DT updates for 6.3
The new Qualcomm QDU1000 and QRU1000 platforms, and the IDP device on
these are introduced. New support for a couple of USB modem sticks from
THWC are introduced, so is support for Xiaomi Mi Pad 5 Pro and the Pro
SKU of the Herobrine device.
The Core Bus Fabric (CBF) is introduced on MSM8996. Interconnect paths
for UFS are also described.
A few fixes related to the power-grid of herobrine, on SC7280, are
introduced.
QFPROM is introduced on IPQ8074 and Interconnect providers are added for
SDM670.
On SDM845 the duplicated wcd9340 audio coded description is moved from
devices to a common file, audio devices are added to the OnePlus 6 and
6T.
On SM6115 debug UART, SMP2P, watchdog nodes are introduced, and the
platform is switched to use #address/size-cells of 2, in line with most
other platforms.
Camera control interface and clock controllers are added for SM6350, and
the CCI interface is enabled on the Fairphone FP4.
On SM8350 the interconnect reference of SDHCI controller is corrected,
DSI1 PHY clocks are properly described as sources for the Display clock
controller and DSI1 is wired up to the display controller.
The firmware paths are corrected for the Sony Xperia Nagara platform.
The GPR bus, audio servic3es and LPASS pinctrl nodes are added for the
SM8550 platform. Additionally a few small typos/errors are corrected.
gpio-ranges are corrected across MSM8953, SM6115 and SC8280XP and a
range of DT validation issues are corrected.
* tag 'qcom-arm64-for-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (81 commits)
arm64: dts: qcom: sc7280: Power herobrine's 3.3 eDP/TS rail more properly
arm64: dts: qcom: pmk8550: fix PON compatible
arm64: dts: qcom: sm8550: fix DSI controller compatible
arm64: dts: qcom: sc7280: Hook up the touchscreen IO rail on evoker
arm64: dts: qcom: sc7280: Hook up the touchscreen IO rail on villager
arm64: dts: qcom: sc7280: Add 3ms ramp to herobrine's pp3300_left_in_mlb
arm64: dts: qcom: sc7280: On QCard, regulator L3C should be 1.8V
arm64: dts: qcom: sc8280xp: correct LPASS GPIO gpio-ranges
arm64: dts: qcom: msm8992-lg-bullhead: Enable regulators
arm64: dts: qcom: sm6115: correct TLMM gpio-ranges
arm64: dts: qcom: msm8953: correct TLMM gpio-ranges
arm64: dts: qcom: msm8992-lg-bullhead: Correct memory overlaps with the SMEM and MPSS memory regions
arm64: dts: qcom: sm8350-hdk: correct LT9611 pin function
arm64: dts: qcom: sm8350-hdk: align pin config node names with bindings
arm64: dts: qcom: sm6350: Use specific qmpphy compatible
arm64: dts: qcom: sm6115: Add smp2p nodes
arm64: dts: qcom: sm7225-fairphone-fp4: Enable CCI busses
arm64: dts: qcom: sm6350: Add CCI nodes
arm64: dts: qcom: sm6350: Add camera clock controller
dt-bindings: clock: add QCOM SM6350 camera clock bindings
...
Link: https://lore.kernel.org/r/20230210192908.2039976-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Several cleanups pointed out by `make dtbs_check`:
1. Align LED status node name with bindings.
2. Drop redundant properties.
3. Move i2c-gpio node out of soc to top-level, as soc node is expected
to have only MMIO nodes.
4. Correct SPI NOR flash compatible in SMDK5250 and SMDKv310.
5. Align GPIO property names in WM1811-family codec nodes with bindings.
6. Correct MAX98090 codec DAI cells in Snow.
-----BEGIN PGP SIGNATURE-----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=HOVS
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=HsWr
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v6.3, part two
Several cleanups pointed out by `make dtbs_check`:
1. Align LED status node name with bindings.
2. Drop redundant properties.
3. Move i2c-gpio node out of soc to top-level, as soc node is expected
to have only MMIO nodes.
4. Correct SPI NOR flash compatible in SMDK5250 and SMDKv310.
5. Align GPIO property names in WM1811-family codec nodes with bindings.
6. Correct MAX98090 codec DAI cells in Snow.
* tag 'samsung-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: correct max98090 DAI argument in Snow
ARM: dts: s5pv210: add "gpios" suffix to wlf,ldo1ena on Aries
ARM: dts: exynos: add "gpios" suffix to wlf,ldo1ena on Arndale
ARM: dts: exynos: add "gpios" suffix to wlf,ldo1ena on Midas
ARM: dts: exynos: correct SPI nor compatible in SMDK5250
ARM: dts: exynos: correct SPI nor compatible in SMDKv310
ARM: dts: exynos: move I2C10 out of soc node on Arndale
ARM: dts: exynos: drop redundant address/size cells from I2C10 on Arndale
ARM: dts: exynos: drop default status from I2C10 on Arndale
ARM: dts: exynos: align status led name with bindings on Origen4210
Link: https://lore.kernel.org/r/20230211113103.58894-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It contains:
- cleanups arround flexcom nodes on SAM9X60 SoC as follows:
- preserve same ID for flexcoms and the embedded nodes (e.g. flx4
will embed uart4, spi4, i2c4 but not e.g. uart1, spi2, i2c3);
- SoC specific bindings were moved from board specific file to SoC
specific file
- DMA bindings for all flexcom nodes were added
- SoC file was filled with missing flexcom nodes
- new SAM9X60 Curiosity board that contains 1 uSDcard interface, 1 SDcard
interface, 1 USB device interface, 2 USB Type-A interfaces, 2 CAN
interfaces, 1 10/100 Ethernet interface, 1 LCD RGB666 interface,
1 Gb DDR2, 4 Gb NAND Flash, 2Kb EEPROM, leds, button, power
regulators, UART and JTAG connectors
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTsZ8eserC1pmhwqDmejrg/N2X7/QUCY+N5WwAKCRCejrg/N2X7
/QIbAQCQ5aARiG6B3IglSdVTQk8a+CRWpelxB9CMCXEohhRkhgD+JS6XRejjoF78
cj3J30OP1SnkZQtTOygxEtmaxEMHNw0=
=gcby
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=Oe5O
-----END PGP SIGNATURE-----
Merge tag 'at91-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 device tree updates for 6.3 #2
It contains:
- cleanups arround flexcom nodes on SAM9X60 SoC as follows:
- preserve same ID for flexcoms and the embedded nodes (e.g. flx4
will embed uart4, spi4, i2c4 but not e.g. uart1, spi2, i2c3);
- SoC specific bindings were moved from board specific file to SoC
specific file
- DMA bindings for all flexcom nodes were added
- SoC file was filled with missing flexcom nodes
- new SAM9X60 Curiosity board that contains 1 uSDcard interface, 1 SDcard
interface, 1 USB device interface, 2 USB Type-A interfaces, 2 CAN
interfaces, 1 10/100 Ethernet interface, 1 LCD RGB666 interface,
1 Gb DDR2, 4 Gb NAND Flash, 2Kb EEPROM, leds, button, power
regulators, UART and JTAG connectors
* tag 'at91-dt-6.3-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60 curiosity board
dt-bindings: arm: at91: Add info on sam9x60 curiosity
ARM: dts: at91: sam9x60: Add missing flexcom definitions
ARM: dts: at91: sam9x60: Add DMA bindings for the flexcom nodes
ARM: dts: at91: sam9x60: Specify the FIFO size for the Flexcom UART
ARM: dts: at91: sam9x60: fix spi4 node
ARM: dts: at91: sam9x60: move flexcom definitions
ARM: dts: at91: sam9x60: Fix the label numbering for the flexcom functions
Link: https://lore.kernel.org/r/20230209084930.289721-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The max98090 has only one DAI and does not take argument to DAI
phandles:
exynos5250-snow-rev5.dtb: audio-codec@10: #sound-dai-cells:0:0: 0 was expected
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20230208160424.371678-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The GPIOs properties should end with "gpios" suffix and Linux gpiolib
already handles both names, so switch to preferred one.
While touching the lines, replace open-coded GPIO_ACTIVE_HIGH flag.
Tested-by: Henrik Grimler <henrik@grimler.se>
Link: https://lore.kernel.org/r/20230208172634.404452-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
SPI NOR flash compatible should come with generic jedec,spi-nor fallback
and proper vendor prefix:
exynos5250-smdk5250.dtb: /soc/spi@12d30000/flash@0: failed to match any schema with compatible: ['w25x80']
Link: https://lore.kernel.org/r/20230208164942.387390-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
SPI NOR flash compatible should come with generic jedec,spi-nor fallback
and proper vendor prefix:
exynos4210-smdkv310.dtb: /soc/spi@13940000/flash@0: failed to match any schema with compatible: ['w25x80']
Link: https://lore.kernel.org/r/20230208164942.387390-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
I2C10 is represented as i2c-gpio device, thus it is not really a part of
soc MMIO bus:
exynos5250-arndale.dtb: soc: i2c-10: {'pinctrl-names': ['default'], ... } should not be valid under {'type': 'object'}
Link: https://lore.kernel.org/r/20230207210020.677007-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The "status" is a reserved keyword and LED nodes should have generic
prefix:
exynos4210-origen.dtb: leds: status: {'gpios': [[76, 3, 1]],
'function': ['heartbeat'], 'linux,default-trigger': ['heartbeat']} is not of type 'array'
Link: https://lore.kernel.org/r/20230207210020.677007-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
This is the equivalent of commit f5b4811e87 ("arm64: dts: qcom:
sc7180: Add trogdor eDP/touchscreen regulator off-on-time") and commit
23ff866987 ("arm64: dts: qcom: sc7180: Start the trogdor
eDP/touchscreen regulator on"), but for herobrine instead of trogdor.
The motivations for herobrine are the same as for trogdor.
NOTES:
* Currently for herobrine all boards are eDP, not MIPI. If/when we
have herobrine derivatives that are MIPI they we can evaluate
whether the same off-on-delay makes sense for them. For trogdor we
didn't add the delay to MIPI panels because the problem was found
late and nobody had complained about it. For herobrine defaulting to
assuming the same 500ms makes sense and if we find we need to
optimize later we can.
* Currently there are no oddball herobrine boards like homestar where
the panel really likes to be power cycled. If we have an oddball
board it will need to split the eDP and touchscreen rail anyway
(like homestar did) and we'll have to delete the "regulator-boot-on"
from that board.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230207163550.1.I5ff72b7746d5fca8f10ea61351bde4150ed1a7f8@changeid
The right compatible is qcom,pmk8350-pon, it matches the
reg resources associated to the node and the subnodes compatible
properties.
Fixes: e9c0a4e484 ("arm64: dts: qcom: Add PMK8550 pmic dtsi")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230207-topic-sm8550-upstream-sm8550-dt-fix-v1-2-698d132ab285@linaro.org
On older revisions of evoker, the touchscreen was either
non-functional or needed special hardware magic to get it talking
properly. It's been decided that the proper way going forward is to
use L3C to power some buffers on the QCard and then configure the
touchscreens for 1.8V. Let's do that.
Note that this is safe to do even on older revs even if it might not
make the touchscreen work there (because they didn't have a properly
stuffed QCard). As talked about in the patch ("arm64: dts: qcom:
sc7280: On QCard, regulator L3C should be 1.8V") the L3C regulator
didn't go anywhere at all on older revs.
This patch relies on the patch ("HID: i2c-hid: goodix: Add
mainboard-vddio-supply") in order to function properly. Without that
patch this one won't do any harm but it won't actually accomplish its
goal.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.7.I2d960ed7f2445db0cf3d227fde985fbd740f3c4d@changeid
On never revs of sc7280-herobrine-villager (rev2+) the L3C rail is
provided to the touchscreen as the IO voltage rail. Let's add it in
the device tree.
NOTE: Even though this is only really needed on rev2+ villagers (-rev0
had non-functioning touchscreen and -rev1 had some hacky hardware
magic), it doesn't actually hurt to do this for old villager revs. As
talked about in the patch ("arm64: dts: qcom: sc7280: On QCard,
regulator L3C should be 1.8V") the L3C regulator didn't go anywhere at
all on older revs. That means that turning it on for older revs
doesn't hurt other than drawing a tiny bit of extra power. Since -rev0
and -rev1 villagers will never make it to real customers and it's nice
not to have too many old device trees, the better tradeoff seems to be
to enable it everywhere.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.3.I740d409bc5bb69bf4a7b3c4568ea6e7a92f16ccd@changeid
The "pp3300_left_in_mlb" rail on herobrine eventually connects up to
"vreg_edp_3p3" on the qcard. On several herobrine designs this rail
has been measured to need more than 1ms to turn on.
While technically a herobrine derivative (defined as anyone including
the "herobrine.dtsi") could change the board to make the rail rise
faster or slower, the fact that two boards (evoker and villager) both
measured it as taking more than 1ms implies that it's probably going
to be the norm. Thus, let's add a "regulator-enable-ramp-delay"
straight into the herobrine.dtsi to handle this. If a particular
derivative board needs a faster or slower one then they can override
it, though that feels unlikely.
While we measured something a bit over 1ms, we'll choose 3ms to give
us a tiny bit of margin. This isn't a rail that turns off and on all
the time anyway and 3ms is nothing compared to the total amount of
time to power on a panel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.2.I13814cefc5ab3e0a39ebd09f052e3fd25d4e8f1d@changeid
On the first sc7280 QCards the L3C rail was never really used for
anything. Stuffing options on the QCard meant that the QCard itself
didn't use this rail for anything. This rail did get sent to the
mainboard, but no existing mainboards ever did anything with it other
that route it to a testpoint.
On later sc7280 QCards, the L3C rail was repurposed. Instead of being
a (nominally) 3.3V rail, it was decided to make it a 1.8V rail. It is
now provided to the display connector (which might route it to the
touchscreen) and also used to power some buffers relating to
touchscreen IO. This rail is getting the additional tag "ts_avccio",
though some places still refer to it as "vreg_l3c_3p0" despite the
fact that the name now specifies the wrong voltage.
Since it never hurts for this rail to be 1.8V (even on old QCards /
old boards), let's just change it to 1.8V across the board and add the
extra "ts_avccio" moniker as a label in the device tree.
Future patches will start using this rail in their touchscreens.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206184744.1.I784f4b3d7e4a06edafff4a3129f52e749889bc05@changeid
The SC8280XP LPASS pin controller has GPIOs 0-18, so correct the number
of GPIOs in gpio-ranges.
Fixes: c18773d162 ("arm64: dts: qcom: sc8280xp: add SoundWire and LPASS")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230203164854.390080-5-krzysztof.kozlowski@linaro.org
The memory region reserved by a previous commit (see fixes tag below)
overlaps with the SMEM and MPSS memory regions, causing error messages in
dmesg:
OF: reserved mem: OVERLAP DETECTED!
reserved@5000000 (0x0000000005000000--0x0000000007200000)
overlaps with smem_region@6a00000
(0x0000000006a00000--0x0000000006c00000)
OF: reserved mem: OVERLAP DETECTED!
reserved@6c00000 (0x0000000006c00000--0x0000000007200000)
overlaps with memory@7000000
(0x0000000007000000--0x000000000ca00000)
This patch resolves both of these by splitting the previously reserved
memory region into two sections either side of the SMEM region and by
cutting off the second memory region to 0x7000000.
Fixes: 22c7e1a0fa ("arm64: dts: msm8992-bullhead: add memory hole region")
Signed-off-by: Jamie Douglass <jamiemdouglass@gmail.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Tested-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230202054819.16079-1-jamiemdouglass@gmail.com
Bindings expect pins to be named with certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: d96d8f9192 ("arm64: dts: qcom: sm8350-hdk: Enable lt9611uxc dsi-hdmi bridge")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230201154321.276419-1-krzysztof.kozlowski@linaro.org
The sc7180 phy compatible works fine for some cases, but it turns out
sm6350 does need proper phy configuration in the driver, so use the
newly added sm6350 compatible.
Because the sm6350 compatible is using the new binding, we need to
change the node quite a bit to match it.
This fixes qmpphy init when no USB cable is plugged in during bootloader
stage.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230120-sm6350-usbphy-v4-3-4d700a90ba16@fairphone.com
Add nodes for the two CCI blocks found on SM6350.
The first contains two i2c busses and while the second one might also
contains two busses, the downstream kernel only has one configured, and
some boards use the GPIOs for the potential cci1_i2c1 one other
purposes, so leave that one unconfigured.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221213-sm6350-cci-v2-3-15c2c14c34bb@fairphone.com
Add device tree bindings for camera clock controller for
Qualcomm Technology Inc's SM6350 SoC.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221213152617.296426-1-konrad.dybcio@linaro.org
DT schema expects names of operating points tables to match certain
pattern:
qcom-ipq4018-ap120c-ac.dtb: opp_table0: $nodename:0: 'opp_table0' does not match '^opp-table(-[a-z0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230120072113.138656-1-krzysztof.kozlowski@linaro.org
Add the node describing the sn3193 that's used to provide notification
LED.
Unfortunately the driver currently supports neither multicolor API nor
using the properties function & color, so we use label instead.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230122-msm8974-bacon-features-v2-5-06bb83c20a58@z3ntu.xyz
