The Microchip LAN966X SerDes PHY is only present on Microchip LAN966x
SoCs. However, when used as a PCI endpoint, all peripherals of the
LAN966x SoC can be accessed by the PCI host. Hence add dependencies on
SOC_LAN966 and MCHP_LAN966X_PCI, to prevent asking the user about this
driver when configuring a kernel without Microchip LAN966x SoC and PCIe
support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/369233dfded88ff6fb342e03794fe31985d84d82.1737383314.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The i.MX95 USB3 phy has a Type-C Assist block (TCA). This block consists
two functional blocks (XBar assist and VBus assist) and one system
access interface using APB.
The primary functionality of XBar assist is:
- switching lane for flip
- moving unused lanes into lower power states.
This info can be get from:
i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.
This will add support for TCA block to achieve lane switching and tca
lower power functionality.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20241204050907.1081781-1-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY is based on a Samsung IP block that supports HDMI 2.1, and eDP
1.4b. RK3588 integrates the Analogix eDP 1.3 TX controller IP and the
HDMI/eDP TX Combo PHY to support eDP display.
Add basic support for RBR/HBR/HBR2 link rates, and the voltage swing and
pre-emphasis configurations of each link rate are set according to the
eDP 1.3 requirements.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250205105157.580060-5-damon.ding@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adding the '_MASK' suffix to all registers in order to ensures consistency
in the naming convention for register macros throughout the file.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250205105157.580060-4-damon.ding@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Complete the register names of CMN_REG(0081) and CMN_REG(0087) to their
full version, and it can help to better match the datasheet.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250205105157.580060-3-damon.ding@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to the datasheet, setting the dig_clk_sel bit of CMN_REG(0097)
to 1'b1 selects LCPLL as the reference clock, while setting it to 1'b0
selects the ROPLL.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250205105157.580060-2-damon.ding@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since commit 7ef9651e97 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables the clocks for the
whole lifetime of the device. Moreover, it is no longer necessary to
unprepare and disable the clocks explicitly.
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://lore.kernel.org/r/tencent_9087BCE04E38E6AA5C4B2252B82FA99C2009@qq.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
As reported by Damon Ding, the phy_get_mode() call doesn't work as
expected unless the PHY driver has a .set_mode() call. This prompts PHY
drivers to have empty stubs for .set_mode() for the sake of being able
to get the mode.
Make .set_mode() callback truly optional and update PHY's mode even if
it there is none.
Cc: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/96f8310f-93f1-4bcb-8637-137e1159ff83@rock-chips.com
Tested-by: Damon Ding <damon.ding@rock-chips.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250209-phy-fix-set-moe-v2-1-76e248503856@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20250111185407.183855-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To make USB runtime suspend work when a UDC has been bound, the phy
needs to inform the USBDRD controller (DWC3) that Vbus and bvalid are
gone, so that it can in turn raise the respective gadget interrupt with
event == DWC3_DEVICE_EVENT_DISCONNECT, which will cause the USB stack
to clean up, allowing DWC3 to enter runtime suspend.
On e850 and gs101 this isn't working, as the respective signals are not
directly connected, and instead this driver uses override bits in the
PHY IP to set those signals. It currently forcefully sets them to 'on',
so the above mentioned interrupt will not be raised, preventing runtime
suspend.
To detect that state, update this driver to act on the TCPC's
orientation signal - when orientation == NONE, Vbus is gone and we can
clear the respective bits. Similarly, for other orientation values we
re-enable them.
This makes runtime suspend work on platforms with a TCPC (like Pixel6),
while keeping compatibility with platforms without (e850-96).
With runtime suspend working, USB-C cable orientation detection now
also fully works on such platforms, and the link comes up as Superspeed
as expected irrespective of the cable orientation and whether UDC /
gadget are configured and active.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-7-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gs101's SS phy needs to be configured differently based on the
connector orientation, as the SS link can only be established if the
mux is configured correctly.
The code to handle programming of the mux is in place already, this commit
now adds the missing pieces to subscribe to the Type-C orientation
switch event.
Note that for this all to work we rely on the USB controller
re-initialising us. It should invoke our .exit() upon cable unplug, and
during cable plug we'll receive the orientation event after which we
expect our .init() to be called.
Above reinitialisation happens if the DWC3 controller can enter runtime
suspend automatically. For the DWC3 driver, this is an opt-in:
echo auto > /sys/devices/.../11110000.usb/power/control
Once done, things work as long as the UDC is not bound as otherwise it
stays busy because it doesn't cancel / stop outstanding TRBs. For now
we have to manually unbind the UDC in that case:
echo "" > sys/kernel/config/usb_gadget/.../UDC
Note that if the orientation-switch property is missing from the DT,
the code will behave as before this commit (meaning for gs101 it will
work in SS mode in one orientation only). Other platforms are not
affected either way.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-6-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
USB SS lanes need to be configured based on the connector orientation -
at most two lanes will be in use for USB (and the remaining two for
alternate modes like DP).
For the USB link to come up in SS, the lane configuration registers
have to be programmed accordingly.
While we still need a way to be notified of the actual connector
orientation and then reprogram the registers accordingly (at the moment
the configuration happens just once during phy_init() and never again),
we can prepare the code doing the configuration to take the orientation
into account.
Do so.
Note: the mutex is needed to synchronize this with the upcoming
connector orientation callback.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-5-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This code's intention is to configure lane0 and lane2 tunings, but for
lane2 there is a typo and it ends up tuning something else.
Fix the typo, as it doesn't appear to make sense to apply different
tunings for lane0 vs lane2.
The same typo appears to exist in the bootloader, hence we restore the
original value in the typo'd registers as well. This can be removed
once / if the bootloader is updated.
Note that this is incorrect in the downstream driver as well - the
values had been copied from there.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-4-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
orientation-switch is the standard declaration to inform the Type-C mux
layer that a remote-endpoint is capable of processing orientation
change messages.
The USB PHY on gs101 needs to be configured based on the orientation of
the connector. For that the DTS needs a link between the phy's port and
a TCPCi, and we'll need to inform the phy driver that it should handle
the orientation (register a handler).
Update the schema to enforce that by requiring the orientation-switch
and port properties on gs101 (only). We disallow orientation-switch on
all other supported platforms, since other versions of this phy (or its
system integration) don't currently support or even need it.
Even though this new required gs101 property is an ABI break, the
intention for the driver is to behave as before if it's missing
(meaning for gs101 it will work in SS mode in one orientation only).
Other platforms are not affected.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-2-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The use of (of|device)_property_read_bool() for non-boolean properties
is deprecated in favor of (of|device)_property_present() when testing
for property presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20241231163121.241543-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It doesn't matter whether "mux-states" is not present or there is some
other issue parsing it causing an error. Drop the presence check and
rework the error handling to ignore anything other than deferred probe.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250203185421.3383805-2-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a new, common configuration for Gen4x4 V6 PHYs without an init
sequence.
The bootloader configures the hardware once and the OS retains that
configuration by using the NOCSR reset line (which doesn't drop
register state on assert) in place of the "full reset" one.
Use this new configuration for X1P42100's Gen4x4 PHY.
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-x1p4_dts-v2-3-72cd4cdc767b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
(Almost?) all QMP PHYs come with both a "full reset" ("phy") and a
"retain certain registers" one ("phy_nocsr").
Drop the maxItems=1 constraint for resets and reset_names as we go
ahead and straighten out the DT usage. After that's done (which
will involve modifying some clock drivers etc.), we may set
*min*Items to 2, bar some possible exceptions.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250203-topic-x1p4_dts-v2-2-72cd4cdc767b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
X1P42100 has two Gen4x4 PHYs instead of one Gen4x4 and one Gen4x8.
They are mostly identical to X1E80100's Gen4x4 PHY, but there are some
minor details in the programming sequences.
Introduce a new compatible for this flavor of the PHY.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-x1p4_dts-v2-1-72cd4cdc767b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add compatible for the HDPTX PHY on rk3576, which is compatible with
rk3588, but without rst_phy/rst_ropll/rst_lcpll.
In fact, these three reset lines are also optional on the rk3588,
they just used for debug, then they were removed on the rk3576 IC
design.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241231092721.252405-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy needs to know its identity in the system (phy0 or phy1 on rk3588)
for some actions and the driver currently contains code abusing of_alias
for that.
Devicetree aliases are always optional and should not be used for core
device functionality, so instead keep a list of phys on a soc in the
of_device_data and find the phy-id by comparing against the mapped
register-base.
Fixes: c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock provider support")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241206103401.1780416-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The variant of the driver in the vendor-tree contained those handy
comments in the regmap register callback. Having the different ranges
describe what they are looks helpful.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241206103401.1780416-2-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
-----BEGIN PGP SIGNATURE-----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=mWV6
-----END PGP SIGNATURE-----
Merge tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
- sh: boards: Use imply to enable hardware with complex dependencies
- sh: Migrate to the generic rule for built-in DTB
- sh: irq: Use seq_put_decimal_ull_width() for decimal values
-----BEGIN PGP SIGNATURE-----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=G6GL
-----END PGP SIGNATURE-----
Merge tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Signed-off-by: Len Brown <len.brown@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCZ5yJdgAKCRBZ7Krx/gZQ
69W4AQDwgxceiQ6icx3rFhCWQigne4jdMO84kd8tNaa+xHGe1AD/WnkeChc5DqjQ
wZWZxAAzml9SS01IcSiHWaF5fgrjlA0=
=rXOq
-----END PGP SIGNATURE-----
Merge tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
-----BEGIN PGP SIGNATURE-----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=/P+2
-----END PGP SIGNATURE-----
Merge tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- various updates for special file handling: symlink handling,
support for creating sockets, cleanups, new mount options (e.g. to
allow disabling using reparse points for them, and to allow
overriding the way symlinks are saved), and fixes to error paths
- fix for kerberos mounts (allow IAKerb)
- SMB1 fix for stat and for setting SACL (auditing)
- fix an incorrect error code mapping
- cleanups"
* tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
cifs: Fix parsing native symlinks directory/file type
cifs: update internal version number
cifs: Add support for creating WSL-style symlinks
smb3: add support for IAKerb
cifs: Fix struct FILE_ALL_INFO
cifs: Add support for creating NFS-style symlinks
cifs: Add support for creating native Windows sockets
cifs: Add mount option -o reparse=none
cifs: Add mount option -o symlink= for choosing symlink create type
cifs: Fix creating and resolving absolute NT-style symlinks
cifs: Simplify reparse point check in cifs_query_path_info() function
cifs: Remove symlink member from cifs_open_info_data union
cifs: Update description about ACL permissions
cifs: Rename struct reparse_posix_data to reparse_nfs_data_buffer and move to common/smb2pdu.h
cifs: Remove struct reparse_posix_data from struct cifs_open_info_data
cifs: Remove unicode parameter from parse_reparse_point() function
cifs: Fix getting and setting SACLs over SMB1
cifs: Remove intermediate object of failed create SFU call
cifs: Validate EAs for WSL reparse points
cifs: Change translation of STATUS_PRIVILEGE_NOT_HELD to -EPERM
...
Here is a single debugfs fix from Al to resolve the reported regression
in linux-next and in the driver-core tree. It has been reported to fix
the issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZ55HfQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykocACgqvoq+99sC6joNEqAuZZil/PU/1wAoNJtys1x
3JTFgphXSjoyMBsmM96b
=pRKD
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull debugfs fix from Greg KH:
"Here is a single debugfs fix from Al to resolve a reported regression
in the driver-core tree. It has been reported to fix the issue"
* tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Fix the missing initializations in __debugfs_file_get()
13 are for MM and 8 are for non-MM. All are singletons, please see the
changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZ54MEgAKCRDdBJ7gKXxA
jlhdAP0evTQ9JX+22DDWSVdWFBbnQ74c5ddFXVQc1LO2G2FhFgD+OXhH8E65Nez5
qGWjb4xgjoQTHS7AL4pYEFYqx/cpbAQ=
=rN+l
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"21 hotfixes. 8 are cc:stable and the remainder address post-6.13
issues. 13 are for MM and 8 are for non-MM.
All are singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
MAINTAINERS: include linux-mm for xarray maintenance
revert "xarray: port tests to kunit"
MAINTAINERS: add lib/test_xarray.c
mailmap, MAINTAINERS, docs: update Carlos's email address
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
mm: gup: fix infinite loop within __get_longterm_locked
mm, swap: fix reclaim offset calculation error during allocation
.mailmap: update email address for Christopher Obbard
kfence: skip __GFP_THISNODE allocations on NUMA systems
nilfs2: fix possible int overflows in nilfs_fiemap()
mm: compaction: use the proper flag to determine watermarks
kernel: be more careful about dup_mmap() failures and uprobe registering
mm/fake-numa: handle cases with no SRAT info
mm: kmemleak: fix upper boundary check for physical address objects
mailmap: add an entry for Hamza Mahfooz
MAINTAINERS: mailmap: update Yosry Ahmed's email address
scripts/gdb: fix aarch64 userspace detection in get_current_task
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
ocfs2: fix incorrect CPU endianness conversion causing mount failure
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
...
-----BEGIN PGP SIGNATURE-----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=49gN
-----END PGP SIGNATURE-----
Merge tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert for a regression in the uvcvideo driver"
* tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "media: uvcvideo: Require entities to have a non-zero unique ID"
MM developers have an interest in the xarray code.
Cc: David Gow <davidgow@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Cc: Tamir Duberstein <tamird@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Revert c7bb5cf9fc ("xarray: port tests to kunit"). It broke the build
when compiing the xarray userspace test harness code.
Reported-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Closes: https://lkml.kernel.org/r/07cf896e-adf8-414f-a629-a808fc26014a@oracle.com
Cc: David Gow <davidgow@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Tamir Duberstein <tamird@gmail.com>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Update .mailmap to reflect my new (and final) primary email address,
carlos.bilbao@kernel.org. Also update contact information in files
Documentation/translations/sp_SP/index.rst and MAINTAINERS.
Link: https://lkml.kernel.org/r/20250130012248.1196208-1-carlos.bilbao@kernel.org
Signed-off-by: Carlos Bilbao <carlos.bilbao@kernel.org>
Cc: Carlos Bilbao <bilbao@vt.edu>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Mattew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
gather_bootmem_prealloc() assumes the start nid as 0 and size as
num_node_state(N_MEMORY). That means in case if memory attached numa
nodes are interleaved, then gather_bootmem_prealloc_parallel() will fail
to scan few of these nodes.
Since memory attached numa nodes can be interleaved in any fashion, hence
ensure that the current code checks for all numa node ids
(.size = nr_node_ids). Let's still keep max_threads as N_MEMORY, so that
it can distributes all nr_node_ids among the these many no. threads.
e.g. qemu cmdline
========================
numa_cmd="-numa node,nodeid=1,memdev=mem1,cpus=2-3 -numa node,nodeid=0,cpus=0-1 -numa dist,src=0,dst=1,val=20"
mem_cmd="-object memory-backend-ram,id=mem1,size=16G"
w/o this patch for cmdline (default_hugepagesz=1GB hugepagesz=1GB hugepages=2):
==========================
~ # cat /proc/meminfo |grep -i huge
AnonHugePages: 0 kB
ShmemHugePages: 0 kB
FileHugePages: 0 kB
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 1048576 kB
Hugetlb: 0 kB
with this patch for cmdline (default_hugepagesz=1GB hugepagesz=1GB hugepages=2):
===========================
~ # cat /proc/meminfo |grep -i huge
AnonHugePages: 0 kB
ShmemHugePages: 0 kB
FileHugePages: 0 kB
HugePages_Total: 2
HugePages_Free: 2
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 1048576 kB
Hugetlb: 2097152 kB
Link: https://lkml.kernel.org/r/f8d8dad3a5471d284f54185f65d575a6aaab692b.1736592534.git.ritesh.list@gmail.com
Fixes: b78b27d029 ("hugetlb: parallelize 1G hugetlb initialization")
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Reported-by: Pavithra Prakash <pavrampu@linux.ibm.com>
Suggested-by: Muchun Song <muchun.song@linux.dev>
Tested-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Reviewed-by: Luiz Capitulino <luizcap@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Donet Tom <donettom@linux.ibm.com>
Cc: Gang Li <gang.li@linux.dev>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We can run into an infinite loop in __get_longterm_locked() when
collect_longterm_unpinnable_folios() finds only folios that are isolated
from the LRU or were never added to the LRU. This can happen when all
folios to be pinned are never added to the LRU, for example when
vm_ops->fault allocated pages using cma_alloc() and never added them to
the LRU.
Fix it by simply taking a look at the list in the single caller, to see if
anything was added.
[zhaoyang.huang@unisoc.com: move definition of local]
Link: https://lkml.kernel.org/r/20250122012604.3654667-1-zhaoyang.huang@unisoc.com
Link: https://lkml.kernel.org/r/20250121020159.3636477-1-zhaoyang.huang@unisoc.com
Fixes: 67e139b02d ("mm/gup.c: refactor check_and_migrate_movable_pages()")
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Aijun Sun <aijun.sun@unisoc.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
There is a code error that will cause the swap entry allocator to reclaim
and check the whole cluster with an unexpected tail offset instead of the
part that needs to be reclaimed. This may cause corruption of the swap
map, so fix it.
Link: https://lkml.kernel.org/r/20250130115131.37777-1-ryncsn@gmail.com
Fixes: 3b644773ee ("mm, swap: reduce contention on device lock")
Signed-off-by: Kairui Song <kasong@tencent.com>
Cc: Chris Li <chrisl@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
On NUMA systems, __GFP_THISNODE indicates that an allocation _must_ be on
a particular node, and failure to allocate on the desired node will result
in a failed allocation.
Skip __GFP_THISNODE allocations if we are running on a NUMA system, since
KFENCE can't guarantee which node its pool pages are allocated on.
Link: https://lkml.kernel.org/r/20250124120145.410066-1-elver@google.com
Fixes: 236e9f1538 ("kfence: skip all GFP_ZONEMASK allocations")
Signed-off-by: Marco Elver <elver@google.com>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Chistoph Lameter <cl@linux.com>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Since nilfs_bmap_lookup_contig() in nilfs_fiemap() calculates its result
by being prepared to go through potentially maxblocks == INT_MAX blocks,
the value in n may experience an overflow caused by left shift of blkbits.
While it is extremely unlikely to occur, play it safe and cast right hand
expression to wider type to mitigate the issue.
Found by Linux Verification Center (linuxtesting.org) with static analysis
tool SVACE.
Link: https://lkml.kernel.org/r/20250124222133.5323-1-konishi.ryusuke@gmail.com
Fixes: 622daaff0a ("nilfs2: fiemap support")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
There are 4 NUMA nodes on my machine, and each NUMA node has 32GB of
memory. I have configured 16GB of CMA memory on each NUMA node, and
starting a 32GB virtual machine with device passthrough is extremely slow,
taking almost an hour.
Long term GUP cannot allocate memory from CMA area, so a maximum of 16 GB
of no-CMA memory on a NUMA node can be used as virtual machine memory.
There is 16GB of free CMA memory on a NUMA node, which is sufficient to
pass the order-0 watermark check, causing the __compaction_suitable()
function to consistently return true.
For costly allocations, if the __compaction_suitable() function always
returns true, it causes the __alloc_pages_slowpath() function to fail to
exit at the appropriate point. This prevents timely fallback to
allocating memory on other nodes, ultimately resulting in excessively long
virtual machine startup times.
Call trace:
__alloc_pages_slowpath
if (compact_result == COMPACT_SKIPPED ||
compact_result == COMPACT_DEFERRED)
goto nopage; // should exit __alloc_pages_slowpath() from here
We could use the real unmovable allocation context to have
__zone_watermark_unusable_free() subtract CMA pages, and thus we won't
pass the order-0 check anymore once the non-CMA part is exhausted. There
is some risk that in some different scenario the compaction could in fact
migrate pages from the exhausted non-CMA part of the zone to the CMA part
and succeed, and we'll skip it instead. But only __GFP_NORETRY
allocations should be affected in the immediate "goto nopage" when
compaction is skipped, others will attempt with DEF_COMPACT_PRIORITY
anyway and won't fail without trying to compact-migrate the non-CMA
pageblocks into CMA pageblocks first, so it should be fine.
After this fix, it only takes a few tens of seconds to start a 32GB
virtual machine with device passthrough functionality.
Link: https://lore.kernel.org/lkml/1736335854-548-1-git-send-email-yangge1116@126.com/
Link: https://lkml.kernel.org/r/1737788037-8439-1-git-send-email-yangge1116@126.com
Signed-off-by: yangge <yangge1116@126.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Barry Song <21cnbao@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If a memory allocation fails during dup_mmap(), the maple tree can be left
in an unsafe state for other iterators besides the exit path. All the
locks are dropped before the exit_mmap() call (in mm/mmap.c), but the
incomplete mm_struct can be reached through (at least) the rmap finding
the vmas which have a pointer back to the mm_struct.
Up to this point, there have been no issues with being able to find an
mm_struct that was only partially initialised. Syzbot was able to make
the incomplete mm_struct fail with recent forking changes, so it has been
proven unsafe to use the mm_struct that hasn't been initialised, as
referenced in the link below.
Although 8ac662f5da ("fork: avoid inappropriate uprobe access to
invalid mm") fixed the uprobe access, it does not completely remove the
race.
This patch sets the MMF_OOM_SKIP to avoid the iteration of the vmas on the
oom side (even though this is extremely unlikely to be selected as an oom
victim in the race window), and sets MMF_UNSTABLE to avoid other potential
users from using a partially initialised mm_struct.
When registering vmas for uprobe, skip the vmas in an mm that is marked
unstable. Modifying a vma in an unstable mm may cause issues if the mm
isn't fully initialised.
Link: https://lore.kernel.org/all/6756d273.050a0220.2477f.003d.GAE@google.com/
Link: https://lkml.kernel.org/r/20250127170221.1761366-1-Liam.Howlett@oracle.com
Fixes: d240629148 ("fork: use __mt_dup() to duplicate maple tree in dup_mmap()")
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peng Zhang <zhangpeng.00@bytedance.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Handle more gracefully cases where no SRAT information is available, like
in VMs with no Numa support, and allow fake-numa configuration to complete
successfully in these cases
Link: https://lkml.kernel.org/r/20250127171623.1523171-1-bfaccini@nvidia.com
Fixes: 63db8170bf (“mm/fake-numa: allow later numa node hotplug”)
Signed-off-by: Bruno Faccini <bfaccini@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Hyeonggon Yoo <hyeonggon.yoo@sk.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Mike Rapoport (IBM)" <rppt@kernel.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Memblock allocations are registered by kmemleak separately, based on their
physical address. During the scanning stage, it checks whether an object
is within the min_low_pfn and max_low_pfn boundaries and ignores it
otherwise.
With the recent addition of __percpu pointer leak detection (commit
6c99d4eb7c ("kmemleak: enable tracking for percpu pointers")), kmemleak
started reporting leaks in setup_zone_pageset() and
setup_per_cpu_pageset(). These were caused by the node_data[0] object
(initialised in alloc_node_data()) ending on the PFN_PHYS(max_low_pfn)
boundary. The non-strict upper boundary check introduced by commit
84c3262991 ("mm: kmemleak: check physical address when scan") causes the
pg_data_t object to be ignored (not scanned) and the __percpu pointers it
contains to be reported as leaks.
Make the max_low_pfn upper boundary check strict when deciding whether to
ignore a physical address object and not scan it.
Link: https://lkml.kernel.org/r/20250127184233.2974311-1-catalin.marinas@arm.com
Fixes: 84c3262991 ("mm: kmemleak: check physical address when scan")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Cc: Patrick Wang <patrick.wang.shcn@gmail.com>
Cc: <stable@vger.kernel.org> [6.0.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
