The current way to determine during HW state sanitization if a PHY is
connected in the expected way doesn't work in all cases. The check for
this considers only the PHY ready/owned state and the initial TC mode
which was determined earlier by the TC port HW readout - using the
sink's HPD and the same PHY ready/owned states.
For instance for an enabled DP-alt/TBT port without the PHY ready/owned
flags set the initial mode will be TBT, and this will be regarded as a
valid PHY state. However it's possible that the port is actually enabled
in DP-alt mode, but for some reason the PHY ownership was not acquired.
Make sure the driver can detect invalid PHY states as in the above
example by checking the PHY ready/owned state wrt. the PLL type used.
This should be the TBT PLL if the PHY is not owned and the MG (non-TBT)
PLL if the PHY is owned.
v2: Rebased on change passing crtc_state in the previous patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-3-imre.deak@intel.com
For clarity factor out the function to determine if there are active
links on a TC port. This prepares for the next patch also checking the
port's PLL type.
While at it pass crtc_state to intel_tc_port_sanitize_mode(), and check
hw.active in that, instead of the deprecated crtc->active flag.
v2: Check crtc_state->hw.active instead of crtc->active. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-2-imre.deak@intel.com
Add an encoder hook, which can be called on enabled TC ports to
determine if the port uses a TBT or a non-TBT PLL. An upcoming patch
will use this to sanity check active TC port's PHY state wrt. the PLL
type used by the port.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-13-imre.deak@intel.com
Since an HDMI output can only be enabled in legacy mode on TC ports,
assume that VBT is wrong and the port is legacy if VBT says the port is
non-legacy and has HDMI. If VBT says to enable DP as well leave the
non-legacy flag enabled, relying on the flag getting fixed up based on
the HPD status during sink detection.
v2: Fix the legacy port flag only if DP is not enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-1-imre.deak@intel.com
For consistency detect the initial TC mode in the PHY owned state the
same way this is done in the not owned state (w/o changing the
behavior). While at it, add more details to the PHY state debug print.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-11-imre.deak@intel.com
Atm, a TC port's initial mode will be read out as TBT mode in any case
the PHY ownership is not held. This isn't correct for legacy ports which
should be used only in legacy mode.
Fix the above initial mode to be disconnected mode for a legacy port and
TBT mode for DP-alt/TBT ports. Determine the port type by checking first
the HPD state and then the legacy VBT flag (so the HPD state can correct
a bogus VBT flag). If a sink is connected on a disabled port the PHY
will get also connected (switching it to legacy mode on a legacy port).
Also connect the PHY on a legacy port if it's enabled but BIOS
incorrectly left it in the disconnected state for some reason.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-10-imre.deak@intel.com
A legacy TC port can't be switched to TBT mode, even if the PHY
initialization wasn't ready yet for some reason, so prevent this.
This shouldn't normally happen as the driver waits for the IOM/TCSS
PHY initialization during driver loading and system resume.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-9-imre.deak@intel.com
Atm, the target TC mode - which the PHY should be switched to at any
point it's used - is TBT in case there is no sink connected. However
legacy ports are only used in the legacy mode regardless of the sink
connected state. Fix the mode returned by
intel_tc_port_get_target_mode() accordingly.
Despite of the above issue, the PHY got disconnected as expected in
response to a sink disconnect event, causing only a redundant
PHY disconnect->reconnect sequence whenever the port was used.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-8-imre.deak@intel.com
During boot-up/system resume, the TC PHY on legacy ports will be
initialized by the IOM/TCSS firmware regardless of a sink being
connected or not (as opposed to DP-alt/TBT ports, which the FW only
inits once a sink is connected).
Wait for the above initialization to complete during HW readout, so that
connecting the PHY later will already see the expected PHY ready state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-6-imre.deak@intel.com
At least restoring the MST topology during system resume needs to use
AUX before the display HW readout->sanitization sequence is complete,
but on TC ports the PHY may be in the wrong mode for this, resulting in
the AUX transfers to fail.
The initial TC port mode is kept fixed as BIOS left it for the above HW
readout sequence (to prevent changing the mode on an enabled port). If
the port is disabled this initial mode is TBT - as in any case the PHY
ownership is not held - even if a DP-alt sink is connected. Thus, the
AUX transfers during this time will use TBT mode instead of the expected
DP-alt mode and so time out.
Fix the above by connecting the PHY during port initialization if the
port is disabled, which will switch to the expected mode (DP-alt in the
above case).
As the encoder/pipe HW state isn't read-out yet at this point, check if
the port is enabled based on the DDI_BUF enabled flag. Save the read-out
initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the
read-out encoder HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-5-imre.deak@intel.com
The commit renaming icl_tc_phy_is_in_safe_mode() to
icl_tc_phy_take_ownership() didn't flip the function's return value
accordingly, fix this up.
This didn't cause an actual problem besides state check errors, since
the function is only used during HW readout.
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: f53979d68a ("drm/i915/display/tc: Rename safe_mode functions ownership")
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-4-imre.deak@intel.com
An enabled TC MST port holds one TC port link reference, regardless of
the number of enabled streams on it, but the TC port HW readout takes
one reference for each active MST stream.
Fix the HW readout, taking only one reference for MST ports.
This didn't cause an actual problem, since the encoder HW readout doesn't
yet support reading out the MST HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-3-imre.deak@intel.com
On TC ports the 4ms AUX timeout combined with the 5 * 32 retry
attempts during DPCD accesses adds a 640ms delay to each access if the
sink is disconnected. This in turn slows down a modeset during which the
sink is disconnected (for instance a disabling modeset).
Prevent the above delay by aborting AUX transfers on a TC port with a
disconnected sink.
The DP 1.4a link CTS (4.2.1.5 Source Device Inactive HPD / Inactive AUX
Test") also requires not to initiate AUX transfers on disconnected DP
ports in general, however this patch doesn't change the behavior on
non-TC ports, leaving that for a follow-up.
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8279
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-2-imre.deak@intel.com
After a few rounds of removal and refactoring Intel MID related code
some artifacts are left untouched. However, they are not used anywhere.
Remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20230216193958.2971-1-andriy.shevchenko%40linux.intel.com
Include a test case to validate the XTILEDATA injection to the target.
Also, it ensures the kernel's ability to copy states between different
XSAVE formats.
Refactor the memcmp() code to be usable for the state validation.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230227210504.18520-3-chang.seok.bae%40intel.com
__copy_xstate_to_uabi_buf() copies either from the tasks XSAVE buffer
or from init_fpstate into the ptrace buffer. Dynamic features, like
XTILEDATA, have an all zeroes init state and are not saved in
init_fpstate, which means the corresponding bit is not set in the
xfeatures bitmap of the init_fpstate header.
But __copy_xstate_to_uabi_buf() retrieves addresses for both the tasks
xstate and init_fpstate unconditionally via __raw_xsave_addr().
So if the tasks XSAVE buffer has a dynamic feature set, then the
address retrieval for init_fpstate triggers the warning in
__raw_xsave_addr() which checks the feature bit in the init_fpstate
header.
Remove the address retrieval from init_fpstate for extended features.
They have an all zeroes init state so init_fpstate has zeros for them.
Then zeroing the user buffer for the init state is the same as copying
them from init_fpstate.
Fixes: 2308ee57d9 ("x86/fpu/amx: Enable the AMX feature in 64-bit mode")
Reported-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/kvm/20230221163655.920289-2-mizhang@google.com/
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/all/20230227210504.18520-2-chang.seok.bae%40intel.com
Cc: stable@vger.kernel.org
Replace of_get_address() and of_translate_address() with single call
to of_address_to_resource(). With this, use ioremap() instead of
of_iomap() which would parse "reg" a second time.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230319163145.225323-1-robh@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The commit 97e3d26b5e ("x86/mm: Randomize per-cpu entry area") fixed
an omission of KASLR on CPU entry areas. It doesn't take into account
KASLR switches though, which may result in unintended non-determinism
when a user wants to avoid it (e.g. debugging, benchmarking).
Generate only a single combination of CPU entry areas offsets -- the
linear array that existed prior randomization when KASLR is turned off.
Since we have 3f148f3318 ("x86/kasan: Map shadow for percpu pages on
demand") and followups, we can use the more relaxed guard
kasrl_enabled() (in contrast to kaslr_memory_enabled()).
Fixes: 97e3d26b5e ("x86/mm: Randomize per-cpu entry area")
Signed-off-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20230306193144.24605-1-mkoutny%40suse.com
Add feature bit to existing device caps field. EFA supports data polling
of 128 bytes blocks.
The flag indicates that the NIC guarentees that a 128 byte aligned block
is written in order, ie that observing the last 8 bits of the block mean
the prior 127 bytes are also written.
It is useful for "last data polling" acceleration techniques.
Link: https://lore.kernel.org/r/20230219081328.10419-1-mrgolin@amazon.com
Reviewed-by: Yehuda Yitschak <yehuday@amazon.com>
Reviewed-by: Yossi Leybovich <sleybo@amazon.com>
Signed-off-by: Yonatan Nachum <ynachum@amazon.com>
Signed-off-by: Michael Margolin <mrgolin@amazon.com>
Acked-by: Gal Pressman <gal.pressman@linux.dev>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use kvm_is_cr4_bit_set() to query SMAP and SMEP when determining whether
or not AMD's SMAP+SEV errata prevents KVM from emulating an instruction.
This eliminates an implicit cast from ulong to bool and makes the code
slightly more readable.
Note, any overhead from making multiple calls to kvm_read_cr4_bits() is
negligible, not to mention the code is question is encountered only in
rare situations, i.e. is not a remotely hot path.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Binbin Wu <binbin.wu@linux.intel.com>
Link: https://lore.kernel.org/r/20230322045824.22970-4-binbin.wu@linux.intel.com
[sean: keep local smap/smep variables, massage changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Convert is_{pae,pse,paging}() to use kvm_is_cr{0,4}_bit_set() and return
bools. Returning an "int" requires not one, but two implicit casts, first
from "unsigned long" to "int", and then again to a "bool". Both casts are
more than a bit dangerous; the ulong=>int casts would drop a bit on 64-bit
kernels _if_ the bits in question weren't in the lower 32 bits, and the
int=>bool cast can result in false negatives/positives, e.g. see commit
0c928ff26b ("KVM: SVM: Fix benign "bool vs. int" comparison in
svm_set_cr0()").
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Binbin Wu <binbin.wu@linux.intel.com>
Link: https://lore.kernel.org/r/20230322045824.22970-3-binbin.wu@linux.intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Add helpers to check if a specific CR0/CR4 bit is set to avoid a plethora
of implicit casts from the "unsigned long" return of kvm_read_cr*_bits(),
and to make each caller's intent more obvious.
Defer converting helpers that do truly ugly casts from "unsigned long" to
"int", e.g. is_pse(), to a future commit so that their conversion is more
isolated.
Opportunistically drop the superfluous pcid_enabled from kvm_set_cr3();
the local variable is used only once, immediately after its declaration.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Binbin Wu <binbin.wu@linux.intel.com>
Link: https://lore.kernel.org/r/20230322045824.22970-2-binbin.wu@linux.intel.com
[sean: move "obvious" conversions to this commit, massage changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Explicitly convert the return from is_paging() to a bool when comparing
against old_paging, which is also a boolean. is_paging() sneakily uses
kvm_read_cr0_bits() and returns an int, i.e. returns X86_CR0_PG or 0, not
1 or 0.
Luckily, the bug is benign as it only results in a false positive, not a
false negative, i.e. only causes a spurious refresh of CR4 when paging is
enabled in both the old and new.
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Fixes: c53bbe2145 ("KVM: x86: SVM: don't passthrough SMAP/SMEP/PKE bits in !NPT && !gCR0.PG case")
Signed-off-by: Sean Christopherson <seanjc@google.com>
When fixed files are unregistered, file_alloc_end and alloc_hint
are not cleared. This can later cause a NULL pointer dereference in
io_file_bitmap_get() if auto index selection is enabled via
IORING_FILE_INDEX_ALLOC:
[ 6.519129] BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
[ 6.541468] RIP: 0010:_find_next_zero_bit+0x1a/0x70
[...]
[ 6.560906] Call Trace:
[ 6.561322] <TASK>
[ 6.561672] io_file_bitmap_get+0x38/0x60
[ 6.562281] io_fixed_fd_install+0x63/0xb0
[ 6.562851] ? __pfx_io_socket+0x10/0x10
[ 6.563396] io_socket+0x93/0xf0
[ 6.563855] ? __pfx_io_socket+0x10/0x10
[ 6.564411] io_issue_sqe+0x5b/0x3d0
[ 6.564914] io_submit_sqes+0x1de/0x650
[ 6.565452] __do_sys_io_uring_enter+0x4fc/0xb20
[ 6.566083] ? __do_sys_io_uring_register+0x11e/0xd80
[ 6.566779] do_syscall_64+0x3c/0x90
[ 6.567247] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[...]
To fix the issue, set file alloc range and alloc_hint to zero after
file tables are freed.
Cc: stable@vger.kernel.org
Fixes: 4278a0deb1 ("io_uring: defer alloc_hint update to io_file_bitmap_set()")
Signed-off-by: Savino Dicanosa <sd7.dev@pm.me>
[axboe: add explicit bitmap == NULL check as well]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Returns EPROBE_DEFER when of_drm_find_bridge() fails, this is consistent
with what all the other DRM bridge drivers are doing and this is
required since the bridge might not be there when the driver is probed
and this should not be a fatal failure.
Cc: <stable@vger.kernel.org>
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Signed-off-by: Matheus Castello <matheus.castello@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230322143821.109744-1-francesco@dolcini.it
Add driver data of mt8195 vdosys1 to mediatek-drm.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-8-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The 104-DIO-48E lacks an IRQ status register. Rather than use the Clear
Interrupt register as the status register, set the no_status flag to
true and thus avoid such a hack.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This patch adds support for devices which don't support readback of
individual interrupt statuses, we report all interrupts as firing and
hope the consumers do the right thing.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmQRx7wACgkQJNaLcl1U
h9D/Nwf+LDKUehiKE+mAaNum7sLGMiemhcBGZp+sCeFpoFq/K5eq3LA+/M+Av3Zj
l92xCxytRX7duHuPgMq+EBOuX4vz5whso11Oz4zRsIicyz7yWn2o2ZkiNsX1Y3lT
5TKVLjK1Kmj8lFGbEr/qJyWGrrhZ1HHdsUDz6H0zAri2x+gqU2eL8SsHNTeJjK1/
18BBZX1xvaICcBqcKUKNzBGDJyowS0/ILHp4zpY3Jjw5gsO9QSQjG7SVmvaNapO8
D60r+v96RQTc+t+dlOb7mbwZBz0VOo5HiMhTieWSfgQ2Bo2nbAkR+X2vpbI3la0U
6Od7pBU5U26C536Y2K9AEhSUa19Kjw==
=EIv8
-----END PGP SIGNATURE-----
Merge tag 'regmap-no-status' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into gpio/for-next
regmap: Add no_status support
This patch adds support for devices which don't support readback of
individual interrupt statuses, we report all interrupts as firing and
hope the consumers do the right thing.
clang with W=1 reports
drivers/gpio/gpio-pxa.c:174:19: error: unused function
'gpio_is_pxa_type' [-Werror,-Wunused-function]
static inline int gpio_is_pxa_type(int type)
^
This function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Add drm ovl_adaptor sub driver. Bring up ovl_adaptor sub driver if
the component exists in the path.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-7-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
MT8195 have two mmsys. Modify drm for MT8195 multi-mmsys support.
The two mmsys (vdosys0 and vdosys1) will bring up two drm drivers,
only one drm driver register as the drm device.
Each drm driver binds its own component. The last bind drm driver
allocates and registers the drm device to drm core.
Each crtc path is created with the corresponding drm driver data.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-6-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This is a preparation for adding support for the ovl_adaptor sub driver
Ovl_adaptor is a DRM sub driver, which doesn't have dma dev. Add
dma_dev_get function for getting representative dma dev in ovl_adaptor.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioachino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-5-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Teach the verifier to recognize PTR_TO_MEM | MEM_RDONLY as not NULL
otherwise if (!bpf_ksym_exists(known_kfunc)) doesn't go through
dead code elimination.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Link: https://lore.kernel.org/bpf/20230321203854.3035-3-alexei.starovoitov@gmail.com
RELO_EXTERN_VAR/FUNC names are not correct anymore. RELO_EXTERN_VAR represent
ksym symbol in ld_imm64 insn. It can point to kernel variable or kfunc.
Rename RELO_EXTERN_VAR->RELO_EXTERN_LD64 and RELO_EXTERN_FUNC->RELO_EXTERN_CALL
to match what they actually represent.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Link: https://lore.kernel.org/bpf/20230321203854.3035-2-alexei.starovoitov@gmail.com
Add ovl_adaptor driver for MT8195.
Ovl_adaptor is an encapsulated module and designed for simplified
DRM control flow. This module is composed of 8 RDMAs, 4 MERGEs and
an ETHDR. Two RDMAs merge into one layer, so this module support 4
layers.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-4-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
ETHDR is a part of ovl_adaptor.
ETHDR is designed for HDR video and graphics conversion in the external
display path. It handles multiple HDR input types and performs tone
mapping, color space/color format conversion, and then combine
different layers, output the required HDR or SDR signal to the
subsequent display path.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-3-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add a new test in copy-mode for testing the copying of metadata from the
buffer in kernel-space to user-space. This is accomplished by adding a
new XDP program and using the bss map to store a counter that is written
to the metadata field. This counter is incremented for every packet so
that the number becomes unique and should be the same as the payload. It
is store in the bss so the value can be reset between runs.
The XDP program populates the metadata and the userspace program checks
the value stored in the metadata field against the payload using the new
is_metadata_correct() function. To turn this verification on or off, add
a new parameter (use_metadata) to the ifobject structure.
Signed-off-by: Tushar Vyavahare <tushar.vyavahare@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20230320102705.306187-1-tushar.vyavahare@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add vdosys1 ETHDR definition.
Signed-off-by: Nancy.Lin <nancy.lin@mediatek.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230321121859.2355-2-nancy.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
When driver doesn't implement a bpf_xdp_metadata kfunc the fallback
implementation returns EOPNOTSUPP, which indicate device driver doesn't
implement this kfunc.
Currently many drivers also return EOPNOTSUPP when the hint isn't
available, which is ambiguous from an API point of view. Instead
change drivers to return ENODATA in these cases.
There can be natural cases why a driver doesn't provide any hardware
info for a specific hint, even on a frame to frame basis (e.g. PTP).
Lets keep these cases as separate return codes.
When describing the return values, adjust the function kernel-doc layout
to get proper rendering for the return values.
Fixes: ab46182d0d ("net/mlx4_en: Support RX XDP metadata")
Fixes: bc8d405b1b ("net/mlx5e: Support RX XDP metadata")
Fixes: 306531f024 ("veth: Support RX XDP metadata")
Fixes: 3d76a4d3d4 ("bpf: XDP metadata RX kfuncs")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/167940675120.2718408.8176058626864184420.stgit@firesoul
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Livepatch timeouts were reported due to busy vhost_worker() kthreads.
Now that cond_resched() can do livepatch task switching, use
cond_resched() in vhost_worker(). That's the better way to
conditionally call schedule() anyway.
Reported-by: Seth Forshee (DigitalOcean) <sforshee@kernel.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Seth Forshee (DigitalOcean) <sforshee@kernel.org>
Link: https://lore.kernel.org/r/509f6ea6fe6505f0a75a66026ba531c765ef922f.1677257135.git.jpoimboe@kernel.org
The current task doesn't need the scheduler's protection to unwind its
own stack.
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Seth Forshee (DigitalOcean) <sforshee@kernel.org>
Link: https://lore.kernel.org/r/4b92e793462d532a05f03767151fa29db3e68e13.1677257135.git.jpoimboe@kernel.org
The entries array in klp_check_stack() is static local because it's too
big to be reasonably allocated on the stack. Serialized access is
enforced by the klp_mutex.
In preparation for calling klp_check_stack() without the mutex (from
cond_resched), convert it to a percpu variable.
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230313233346.kayh4t2lpicjkpsv@treble
Unfortunately, in commit 5911d78fab a wrong codec patch was selected.
The model=alc283-dac-wcaps is equivalent to ALC283_FIXUP_CHROME_BOOK not
ALC295_FIXUP_CHROME_BOOK.
Fixes: 5911d78fab ("ALSA: hda/realtek: Improve support for Dell Precision 3260")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230322153404.386473-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
