Add entry for the TAS5720A-Q1 driver in the dt-bindings doc.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-4-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the reserved bit 7 in the ANALOG_CTRL_REG for the TAS5720A-Q1 device,
when probing.
The datasheet mentions that the bit should be 1 during reset/powerup.
The device did not initialize before setting this value to 1. So, this
could be a quirk of this device. Or it could be a quirk with the board on
which it was tested.
That is why this patch is separate from the patch that adds support for the
TAS5720A-Q1 device.
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-3-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
This change adds support the TAS5720A-Q1 audio codec, in the same driver as
tas5720.
Functionally, this driver is pretty similar to it's TAS5720x variant.
The first 3 registers are the same, so the main control and device
identification can happen with these registers.
The next registers differ.
This variant offers control (in the registers) for 2 speakers, which is
implemented here (in a basic manner).
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-2-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to be re-used in tas5720_mute() (which is part of the dai_ops) and
also in the tas5720_fault_check_work() hook.
The benefit here isn't too great (now).
It's only when we add support for a new device with a slightly different
regmap that this becomes more useful.
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230128082744.41849-1-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
Get rid of the vf610 sai special case, instead update the vfxxx.dtsi
DT to use the same DMA channel ordering as all the other devices. The
sai DMA channel ordering has not been aligned with other IP DMA channel
ordering in the vfxxx.dtsi anyway.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230105144145.165010-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor bit width calculation using params_physical_width()
instead hard-code values.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://lore.kernel.org/r/20230130100104.4076640-1-venkataprasad.potturu@amd.com
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As soon as the first handler or sysfs file is registered
the mutex may get used.
Move the initialization to before any handler registration /
sysfs file creation.
Likewise move the destruction of the mutex to after all
the de-initialization is done.
Fixes: da5ce22df5 ("platform/x86/amd/pmf: Add support for PMF core layer")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230130132554.696025-1-hdegoede@redhat.com
Every power mode of static power slider has its own AC and DC power
settings.
When the power source changes from AC to DC, corresponding DC thermals
were not updated from PMF config store and this leads the system to always
run on AC power settings.
Fix it by registering with power_supply notifier and apply DC settings
upon getting notified by the power_supply handler.
Fixes: da5ce22df5 ("platform/x86/amd/pmf: Add support for PMF core layer")
Suggested-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-6-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
By design PMF static slider will be set to BALANCED during
init, but updating to corresponding thermal values from
the PMF config store was missed, leading to improper settings
getting propagated to PMFW.
Fixes: 4c71ae4144 ("platform/x86/amd/pmf: Add support SPS PMF feature")
Suggested-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-5-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Auto-mode thermal limits should be updated only after receiving the AMT
event. But due to a bug in the older commit, these settings were getting
applied during the auto-mode init.
Fix this by removing amd_pmf_set_automode() during auto-mode
initialization.
Fixes: 3f5571d995 ("platform/x86/amd/pmf: Add support for Auto mode feature")
Suggested-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-4-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add helper routine to check if the current platform profile
is balanced mode and remove duplicate code occurrences.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-3-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add helper routine to update the static slider information
and remove the duplicate code occurrences after this change.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Merge changes affecting thermal control on Intel platforms for 6.3-rc1:
- Consolidate code accessing the Intel TCC (Thermal Control Circuitry)
MSRs by introducing library functions for that and making the
TCC-related code in thermal drivers use them (Zhang Rui).
- Enhance the x86_pkg_temp_thermal driver to support dynamic tjmax
changes (Zhang Rui).
- Address an "unsigned expression compared with zero" warning in the
intel_soc_dts_iosf thermal driver (Yang Li).
- Update comments regarding two functions in the Intel Menlow thermal
driver (Deming Wang).
- Use sysfs_emit_at() instead of scnprintf() in the int340x thermal
driver (ye xingchen).
- Make the intel_pch thermal driver support the Wellsburg PCH (Tim
Zimmermann).
- Add trip point initialization helper functions for ACPI-defined trip
points and modify two thermal drivers to use them (Rafael Wysocki,
Daniel Lezcano).
- Modify the intel_pch and processor_thermal_device_pci thermal drivers
use generic trip point tables instead of thermal zone trip point
callbacks (Daniel Lezcano).
- Add production mode attribute sysfs attribute to the int340x thermal
driver (Srinivas Pandruvada).
- Rework dynamic trip point updates handling and locking in the int340x
thermal driver (Rafael Wysocki).
- Make the int340x thermal driver use a generic trip points table
instead of thermal zone trip point callbacks (Rafael Wysocki, Daniel
Lezcano).
* thermal-intel:
thermal: intel: int340x: Use generic trip points table
thermal: intel: int340x: Use zone lock for synchronization
thermal: intel: int340x: Rework updating trip points
thermal: ACPI: Initialize trips if temperature is out of range
thermal: intel: processor_thermal_device_pci: Use generic trip point
thermal: intel: int340x: Add production mode attribute
thermal: intel: intel_pch: Use generic trip points
thermal: ACPI: Add ACPI trip point routines
thermal: intel: intel_pch: Add support for Wellsburg PCH
thermal: int340x_thermal: Use sysfs_emit_at() instead of scnprintf()
thermal: intel: menlow: Update function descriptions
thermal: intel: Fix unsigned comparison with less than zero
thermal/x86_pkg_temp_thermal: Add support for handling dynamic tjmax
thermal/x86_pkg_temp_thermal: Use Intel TCC library
thermal/intel/intel_tcc_cooling: Use Intel TCC library
thermal/intel/intel_soc_dts_iosf: Use Intel TCC library
thermal/int340x/processor_thermal: Use Intel TCC library
thermal/intel: Introduce Intel TCC library
In case of using MIXer with Simple Audio Card, it needs below DT.
simple-audio-card,dai-link@1 {
cpu@0 {
...
};
cpu@1 {
...
};
...
};
This case, it requires "reg = <xxx>" which needs #address-cells/#size-cells,
but simple-audio-card.yaml is missing these. This patch adds it.
Without this patch, we will get below warning.
${LINUX}/arch/arm64/boot/dts/renesas/r8a77950-ulcb.dtb: sound: simple-audio-card,dai-link@0: '#address-cells', '#size-cells' do not match any of the regexes: '^codec(@[0-9a-f]+)?', '^cpu(@[0-9a-f]+)?', 'pinctrl-[0-9]+'
From schema: ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.yaml
Link: https://lore.kernel.org/r/167344317928.394453.14105689826645262807.robh@kernel.org
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87cz757rdi.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current renesas,rsnd is requesting #sound-dai-cells, but it is
needed in case of it is using "simple-card", but not needed in case of
"audio-graph". We will get below warning without this patch.
This patch fiup it.
${LINUX}/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dtb: sound@ec500000: '#sound-dai-cells' is a required property
From schema: ${LINUX}/Documentation/devicetree/bindings/sound/renesas,rsnd.yaml
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87edrl7rf4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SRC is not implemented on some SoC, thus
interrupts/dmas/dma-names are not mandatory.
This patch solve it. Without this patch we will get below error
when 'make DT_CHECKER_FLAGS=-m dt_binding_check'.
dtschema/dtc warnings/errors:
${LINUX}/Documentation/devicetree/bindings/sound/renesas,rsnd.example.dtb: \
sound@ec500000: Unevaluated properties are not allowed ('rcar_sound,src' was unexpected)
From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/sound/renesas,rsnd.yaml
Link: https://lore.kernel.org/r/167344317928.394453.14105689826645262807.robh@kernel.org
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87fsc17rfa.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
renesas,rsnd.yaml is possible to use ports/port/endpoint if it is using
Audio Graph Card/Card2 for sound. The schema is defined under
audio-graph-port.yaml.
rsnd driver needs "playback/capture" property under endpoint, but it is not
defined in audio-graph-port.yaml. This patch adds missing "playback/capture"
properties under endpoint.
Without this patch, we will get below warning
${LINUX}/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dtb: sound@ec500000: ports:port@0:endpoint: Unevaluated properties are not allowed ('playback', 'capture' were unexpected)
From schema: ${LINUX}/Documentation/devicetree/bindings/sound/renesas,rsnd.yaml
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h6wh7rfj.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ak4613 is possible to use Of-graph (Audio-Graph-Card) style,
but we need to indicate it. Otherwise we will get below warning.
This patch add it.
${LINUX}/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dtb: codec@10: 'port' does not match any of the regexes: '^asahi-kasei,in[1-2]-single-end$', '^asahi-kasei,out[1-6]-single-end$', 'pinctrl-[0-9]+'
From schema: ${LINUX}/Documentation/devicetree/bindings/sound/ak4613.yaml
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87ilgx7rfp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio Graph port doesn't use prefix.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/87lelt7rg6.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio Graph endpoint is possible to have clocks, and system-clock-xxx,
but these are missing on audio-graph-port.yaml.
These have been already defined on simple-card.yaml.
This patch re-use these. We will get below warning without this patch.
${LINUX}/arch/arm64/boot/dts/renesas/r8a77950-ulcb-kf.dtb: audio-codec@44: ports:port@0:endpoint: Unevaluated properties are not allowed ('clocks' was unexpected)
From schema: ${LINUX}/Documentation/devicetree/bindings/sound/ti,pcm3168a.yaml
Link: https://lore.kernel.org/r/87pmcmpyml.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mt697rgg.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-port is missing "mclk-fs" on ports/port,
it is used not only endpoint. It is already defined on simple-card.
This patch fixup it.
Without this patch, we will get below warning.
${LINUX}/arch/arm64/boot/dts/renesas/r8a77951-ulcb-kf.dtb: audio-codec@44: ports: 'mclk-fs' does not match any of the regexes: '^port@[0-9a-f]+$', 'pinctrl-[0-9]+'
From schema: ${LINUX}/Documentation/devicetree/bindings/sound/ti,pcm3168a.yaml
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7qp7rgp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio Graph user needs "ports" not only "port".
This patch adds standard "ports" as definitions to use it easily.
If user needs standard "ports", it can use
ports:
$ref: audio-graph-port.yaml#/definitions/ports
If user want to use custom ports, it can re-use
audio-graph-port.yaml#/definitions/port-base"
audio-graph-port.yaml#/definitions/endpoint-base"
Link: https://lore.kernel.org/r/87sfhipynv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmb57rh2.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio Graph base driver might need to add its own properties.
In such case, having definitions for port/endpoint is easy to handle it.
This patch adds definitions for port/endpoint.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r0vl7rj4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To update properly bits in the register the mask should be used
to clear old value and then the result should be or-ed with new
value, for such updates there is separate helper intel_de_rmw.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221219092428.2515430-1-andrzej.hajda@intel.com
fscache_create_volume_work() uses wake_up_bit() to wake up the processes
which are waiting for the completion of volume creation. According to
comments in wake_up_bit() and waitqueue_active(), an extra smp_mb() is
needed to guarantee the memory order between FSCACHE_VOLUME_CREATING
flag and waitqueue_active() before invoking wake_up_bit().
Fixing it by using clear_and_wake_up_bit() to add the missing memory
barrier.
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20230113115211.2895845-3-houtao@huaweicloud.com/ # v3
The freeing of relinquished volume will wake up the pending volume
acquisition by using wake_up_bit(), however it is mismatched with
wait_var_event() used in fscache_wait_on_volume_collision() and it will
never wake up the waiter in the wait-queue because these two functions
operate on different wait-queues.
According to the implementation in fscache_wait_on_volume_collision(),
if the wake-up of pending acquisition is delayed longer than 20 seconds
(e.g., due to the delay of on-demand fd closing), the first
wait_var_event_timeout() will timeout and the following wait_var_event()
will hang forever as shown below:
FS-Cache: Potential volume collision new=00000024 old=00000022
......
INFO: task mount:1148 blocked for more than 122 seconds.
Not tainted 6.1.0-rc6+ #1
task:mount state:D stack:0 pid:1148 ppid:1
Call Trace:
<TASK>
__schedule+0x2f6/0xb80
schedule+0x67/0xe0
fscache_wait_on_volume_collision.cold+0x80/0x82
__fscache_acquire_volume+0x40d/0x4e0
erofs_fscache_register_volume+0x51/0xe0 [erofs]
erofs_fscache_register_fs+0x19c/0x240 [erofs]
erofs_fc_fill_super+0x746/0xaf0 [erofs]
vfs_get_super+0x7d/0x100
get_tree_nodev+0x16/0x20
erofs_fc_get_tree+0x20/0x30 [erofs]
vfs_get_tree+0x24/0xb0
path_mount+0x2fa/0xa90
do_mount+0x7c/0xa0
__x64_sys_mount+0x8b/0xe0
do_syscall_64+0x30/0x60
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Considering that wake_up_bit() is more selective, so fix it by using
wait_on_bit() instead of wait_var_event() to wait for the freeing of
relinquished volume. In addition because waitqueue_active() is used in
wake_up_bit() and clear_bit() doesn't imply any memory barrier, use
clear_and_wake_up_bit() to add the missing memory barrier between
cursor->flags and waitqueue_active().
Fixes: 62ab633523 ("fscache: Implement volume registration")
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20230113115211.2895845-2-houtao@huaweicloud.com/ # v3
EFI_MEMORY_ATTRIBUTE_PROTOCOL servers as a better alternative to
DXE services for setting memory attributes in EFI Boot Services
environment. This protocol is better since it is a part of UEFI
specification itself and not UEFI PI specification like DXE
services.
Add EFI_MEMORY_ATTRIBUTE_PROTOCOL definitions.
Support mixed mode properly for its calls.
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Evgeniy Baskov <baskov@ispras.ru>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
If TMC ETR is enabled without being ready, in later use we may
see AXI bus errors caused by accessing invalid addresses.
Signed-off-by: Yabin Cui <yabinc@google.com>
[ Tweak error message ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230127231001.1920947-1-yabinc@google.com
For MT8195, VPPSYS0 and VPPSYS1 are 2 display pipes with
hardware differences in power domains, clocks and subsystem counts,
which should be determined by compatible names.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230118031509.29834-3-moudy.ho@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The rfkill() callback was invoked with wrong parameters.
It was missed since MEI is defined now as depending on BROKEN.
Fix that.
Fixes: d288067ede ("wifi: iwlwifi: mei: avoid blocking sap messages handling due to rtnl lock")
Fixes: 5aa7ce31bd ("wifi: iwlwifi: mei: make sure ownership confirmed message is sent")
Fixes: 95170a46b7 ("wifi: iwlwifi: mei: don't send SAP commands if AMT is disabled")
Link: https://lore.kernel.org/r/20230126222821.305122-2-gregory.greenman@intel.com
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Read the STEP equalizer parameters from the BIOS during init
and transfer it to the firmware.
This table provides values to configure an equalizer at the transmitter
that can be used to compensate for PCB channel attenuation.
Signed-off-by: Ayala Barazani <ayala.barazani@intel.com>
Link: https://lore.kernel.org/r/20230127002430.f25f871c5e17.I8390ab916c8f681229433ebc576ed37a594c6d30@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Instead of calculating the offset to the 802.11 header based on radiotap
bits and length, shorten the code path by always setting the MAC header
in the skb and using skb_mac_header().
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Link: https://lore.kernel.org/r/20230127002430.3ec5493934a4.I1d41a2af28588b5899fcd2402f8c4bd8cc29a12e@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
This change fixes the checkpatch warning described in this commit
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230127002430.a25158d58fd7.Ibfe217f12a63c1d5349218e74c4b802c70c13c7c@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Now with all the prework, this is fairly simple, just report the
new bandwidth and RX_ENC_EHT type in RX, and for now just do a
minimal report of the EHT TLC rate in iwl_mvm_set_sta_rate().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20230109130329.5f34d73d1f74.Ib27ae7bd23bc152d61021fd73aabdc76679b9fe4@changeid
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>