This is done to avoid ambiguity between BIOS and UEFI versions. Management
tools can be used for getting accurate firmware version information.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20230322092713.6961-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the preferred form of branch-and-link for finding the current
address so objtool doesn't think it is an unannotated intra-function
call.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230407040924.231023-1-npiggin@gmail.com
This reverts commit baf7cbd94b.
There are some duplicate cache attributes populations executed
in both ci_leaf_init() and later cache_setup_properties().
Revert the commit baf7cbd94b ("riscv: Set more data to cacheinfo")
to setup only the level and type attributes at this early place.
Signed-off-by: Song Shuai <suagrfillet@gmail.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230308064734.512457-1-suagrfillet@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
All callers of pci_bridge_wait_for_secondary_bus() supply a timeout of
PCIE_RESET_READY_POLL_MS, so drop the parameter. Move the definition of
PCIE_RESET_READY_POLL_MS into pci.c, the only user.
[bhelgaas: extracted from
https://lore.kernel.org/r/20230404052714.51315-3-mika.westerberg@linux.intel.com]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe r6.0 sec 6.6.1 prescribes that a device must be able to respond to
config requests within 1.0 s (PCI_RESET_WAIT) after exiting conventional
reset and this same delay is prescribed when coming out of D3cold (as that
involves reset too).
A device that requires more than 1 second to initialize after reset may
respond to config requests with Request Retry Status completions (sec
2.3.1), and we accommodate that in Linux with a 60 second cap
(PCIE_RESET_READY_POLL_MS).
Previously we waited up to PCIE_RESET_READY_POLL_MS only in the reset code
path, not in the resume path. However, a device has surfaced, namely Intel
Titan Ridge xHCI, which requires a longer delay also in the resume code
path.
Make the resume code path to use this same extended delay as the reset
path.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216728
Link: https://lore.kernel.org/r/20230404052714.51315-2-mika.westerberg@linux.intel.com
Reported-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Newline characters will be taken into account for the firmware search
path parameter, warn users about that and provide an example using 'echo
-n' such that it clarifies the typical use of that parameter.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230402135423.3235-1-f.fainelli@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Enable SDMA queue empty context switching. SDMA context switch due to
quantum programming no longer done here (as of sdma v6), so re-name
sdma_v6_0_ctx_switch_enable to sdma_v6_0_ctxempty_int_enable to reflect
this.
Also program SDMAx_QUEUEx_SCHEDULE_CNTL for context switch due to
quantum in KFD. Set to amdgpu_sdma_phase_quantum (defaults to 32 i.e.
3200us).
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Stanley Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CP_HQD_HQ_STATUS0[29] bit will be used by CPFW to acknowledge whether
PCIe atomics are supported. The default value of this bit is set
to 0. Driver will check whether PCIe atomics are supported and set the
bit to 1 if supported. This will force CPFW to use real atomic ops.
If the bit is not set, CPFW will default to read/modify/write using the
firmware itself.
This is applicable only to GFX11 RS64 CP with MEC FW >= 509. If MEC
FW < 509 and for all GFX11 F32 CP, PCIe atomics needs to be supported
else it will skip the device.
This commit also involves moving amdgpu_amdkfd_device_probe() function
call after per-IP early_init loop in amdgpu_device_ip_early_init()
function so as to check for RS64 enabled device.
Signed-off-by: Sreekant Somasekharan <sreekant.somasekharan@amd.com>
Reviewed-by: Graham Sider <Graham.Sider@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some more logging for DP link traning test pattern seqeunces
for better debugging.
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
XGMI RAS should be according to the gmc xgmi physical nodes number,
XGMI RAS should not be enabled if xgmi num_physical_nodes is zero.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aldebaran supports VCN and JPEG RAS, it reports unexpected
block id message during VCN and JPEG RAS initialization if VCN
and JPEG block id not defined.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This achieves the same result as the sequence used in emit_flush_gpu_tlb
but the invalidation is now a single packet instead of the 3 packets
required to implement reg_write_reg_wait.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the existing log with DP LT downspread info:
[Downstream devices shall support down spreading of the link clock.
The down-spread amplitude shall either be disabled (0.0%) or up to 0.5%,
as written by the upstream device to the DOWNSPREAD_CTRL register
(DPCD 00107h). The modulation frequency range shall be 30 to 33 kHz]
Besides, fix checkpatch warning:
CHECK: Alignment should match open parenthesis
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang with W=1 reports
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_enc_cfg.c:625:6: error:
variable 'matching_stream_ptrs' set but not used [-Werror,-Wunused-but-set-variable]
int matching_stream_ptrs = 0;
^
This variable is not used so remove it.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smatch reports
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:44:24: warning: symbol
'dml20_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:51:24: warning: symbol
'dml20v2_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:58:24: warning: symbol
'dml21_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:65:24: warning: symbol
'dml30_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:72:24: warning: symbol
'dml31_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:79:24: warning: symbol
'dml314_funcs' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.c:86:24: warning: symbol
'dml32_funcs' was not declared. Should it be static?
These variables are only used in one file so should be static.
Cleanup whitespace, use tabs consistently for indents.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smatch reports
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubp.c:758:10: warning: symbol
'aperture_default_system' was not declared. Should it be static?
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubp.c:759:10: warning: symbol
'context0_default_system' was not declared. Should it be static?
These variables are only used in one file so should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smatch reports
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn314/dcn314_fpu.c💯37: warning: symbol
'dcn3_14_soc' was not declared. Should it be static?
This variable is only used in one file so should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
regGOLDEN_TSC_COUNT_LOWER/regGOLDEN_TSC_COUNT_UPPER are protected and
unaccessible under sriov.
The clock counter high bit may update during reading process.
[How]
Replace regGOLDEN_TSC_COUNT_LOWER/regGOLDEN_TSC_COUNT_UPPER with
regCP_MES_MTIME_LO/regCP_MES_MTIME_HI to get gpu clock under sriov.
Refine get gpu clock counter method to make the result more precise.
Signed-off-by: Tong Liu01 <Tong.Liu01@amd.com>
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DMA-MAP userptr on other GPUs, the dma address array
will be populated in amdgpu_ttm_backend_bind.
Remove the redundant call from the driver.
v2:
update the comment
Signed-off-by: Shane Xiao <shane.xiao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SG BO to DMA-map userptrs on other GPUs, the SG BO
need inherit MTYPEs in PTEs from original BO.
If we set the flags, the device can be coherent with
the CPUs and other GPUs.
v2:
1. Drop unnecessary flags check
2. Remove local variable align
Signed-off-by: Shane Xiao <shane.xiao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The comment mentions that power1 cap attributes are not supported on
Vangogh, but the opposite is indeed valid: for APUs, only Vangogh is
supported. While at it, also fixed the Renoir comment below (thanks
Melissa for noticing that!).
Cc: Lijo Lazar <lijo.lazar@amd.com>
Cc: Melissa Wen <mwen@igalia.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For userptr bo with iommu on, multiple GPUs use same system
memory dma mapping address when both adev and bo_adev are in
identity mode or in the same iommu group.
If RAM direct map to one GPU, other GPUs can share the original
BO in order to reduce dma address array usage when RAM can
direct map to these GPUs. However, we should explicit check
whether RAM can direct map to all these GPUs.
This patch fixes a potential issue that where RAM is
direct mapped on some but not all GPUs.
v2:
1. Update comment
2. Add helper function reuse_dmamap
Signed-off-by: Shane Xiao <shane.xiao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver doesn't resubmit jobs on hangs any more, hence drop
the hang limit parameter - amdgpu_job_hang_limit, wherever it is used.
Suggested-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Kent Russell <kent.russell@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The adev->dm.dc pointer can be NULL and dereferenced in amdgpu_dm_fini()
without checking.
Add a NULL pointer check before calling dc_dmub_srv_destroy().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 9a71c7d317 ("drm/amd/display: Register DMUB service with DC")
Signed-off-by: Igor Artemiev <Igor.A.Artemiev@mcst.ru>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This DC version brings along:
- FW Release 0.0.161.0
- Improvements on FPO/FAMS
- Correction to DML calculation
- Fix to multiple clock related issues
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The array is hardcoded to 8 in atomfirmware.h, but firmware provides
a bigger one sometimes. Deferencing the larger array causes an out
of bounds error.
commit 4fc1ba4aa5 ("drm/amd/display: fix array index out of bound error
in bios parser") fixed some of this, but there are two other cases
not covered by it. Fix those as well.
Reported-by: erhard_f@mailbox.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214853
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2473
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add command to idle opt.
- Rename d3 entry event and add idle trigger param on
notify event.
- Add bit to fw boot status to notify status when hardware
is powered up.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
New sequence for transparent mode DP1.x link training was provided by LTTPR
vendor
[HOW]
Implement new FIXED_VS sequence, increase LT retry count to minimize
any potential intermittent lightup failures
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
As MES KIQ is dequeued, tell RLC that KIQ is inactive
[How]
Clear the RLC_CP_SCHEDULERS Active bit which RLC checks KIQ status
In addition, driver can halt MES under SRIOV when unloading driver
v2:
Use scheduler0 mask to clear KIQ portion of RLC_CP_SCHEDULERS
Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Reviewed-by: Horace Chen <horace.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
based on dscclk instance offset check conditiona program dscclk
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- On init if a display is connected, we need to maintain the DISPCLK
frequency
- Even though DPG_EN=1, the display still requires the correct
timing or it could cause audio corruption (if DISPCLK freq
is reduced)
- Read the current DISPCLK freq and request the same value to ensure
the timing is valid and unchanged
- However, add option to do a full pipe power down (including link)
which will also avoid audio related issues
- Disabled for the time being on dcn32
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When determining FPO support, include FPO + VActive support
- Support FPO + VActive if one display meets regular requirements
for FPO and the second display is able to switch in VACTIVE with
a given amount of margin
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In 2560x1600@240p eDP panel, driver use lowest voltage level
to play 1080p video cause underflow. According to HW SPEC,
the senario should use high voltage level.
[How]
ChromaPre value is zero when bandwidth validation.
Correct ChromaPre calculation.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To enable root clock optimizations, we need a number of
register writes and need to account for the difference
in DPSTREAMCLK between DCN31 and DCN314. To prevent
issues, add a number of register writes to
DCCG_MASK_SH_LIST_DCN314_COMMON(), and define dccg314_init()
which is mostly in alignment with dccg31_init() but
accounts for the new DPSTREAMCLK sequence.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It will introduce the extra warnning log on some asic
that doesn't register
[HOW]
Add the register on dcn32
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- If we find that applying FAMS doesn't reduce the voltage level,
we will not use it
- Ensure to clear the stream flags indicating FAMS if we hit this
case
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need dequeue MES KIQ under SRIOV when unloading driver
[How]
Modify mes_v11_0_kiq_dequeue_sched which was used to dequeue MES SCHED
to support veriable pipe.
Add MES KIQ dequeue in hw fini
Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Reviewed-by: Horace Chen <horace.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang with W=1 reports
drivers/gpu/drm/amd/amdgpu/../display/modules/freesync/freesync.c:1132:15: error: variable
'average_render_time_in_us' set but not used [-Werror,-Wunused-but-set-variable]
unsigned int average_render_time_in_us = 0;
^
This variable is not used so remove it, which caused i to be unused so remove that as well.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Added some new parameters defined for the gfx usermode queues
use cases in the v11_mqd_struct.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian Koenig <christian.koenig@amd.com>
Reviewed-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Arvind Yadav <Arvind.Yadav@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid new mes fw running with old driver, rename
mes schq fw to gc_*_mes_2.bin.
v2: add MODULE_FIRMWARE declaration
v3: squash in fixup patch
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Skip mode2 reset only for IMU enabled APUs when do S4.
This patch is to fix the regression issue
https://gitlab.freedesktop.org/drm/amd/-/issues/2483
It is generated by commit b589626674 ("drm/amdgpu: skip ASIC reset
for APUs when go to S4").
Fixes: b589626674 ("drm/amdgpu: skip ASIC reset for APUs when go to S4")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2483
Tested-by: Yuan Perry <Perry.Yuan@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SVE and SME are separate features which can be implemented without each
other but currently if the user specifies arm64.nosve then we disable SME
as well as SVE. There is already a separate override for SME so remove the
implicit disablement from the SVE override.
One usecase for this would be testing SME only support on a system which
implements both SVE and SME.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230315-arm64-override-sve-sme-v2-1-bab7593e842b@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>