Three drivers, rtl8192ce, rtl8192cu and rtl8192de, use the same macro
to check if a particular rate is in the CCK set. This common code is
relocated to a common header file. A distinct macro used by rtl8192se
with the same name is renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various modparam messages are difficult to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CCK/OFDM noise immunilty values are always reset to defaults
during bgscan. This could affect the link quality and
performance when the STA is associated in a noisy channel.
So do not override the learned values across the scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The file nfc.h was moved from include/net to include/net/nfc,
since new NFC header files will be added to include/net/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 2 new nfc control operations:
dev_up to turn on the nfc device
dev_down to turn off the nfc device
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit d1b08284 use new frag API but would leave f to be used
uninitialized, this patch fix it.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the Nomadik GPIO driver tracks enabled/disabled interrupt
status with a local variable, switch to using the interrupt core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The GPIO clock is required for register access and interrupt detection.
When interrupt detection is not required on any of the pin in a block,
the block's clock can be disabled when the registers are not being
accessed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[Adjust for new IRQ chip core code, use only local functions]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
- Replace multiple spaces with tabs
- Remove spaces before labels
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There is a bug where a device with index 6 would write out of bounds in
the array of paired devices.
This patch fixes that problem.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Olivier Gay <ogay@logitech.com>
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The function hidraw_disconnect() only acquires the hidraw minors_lock
when clearing the entry in hidraw_table. However the device_destroy()
call can cause a userland read/write to return with an error. It may
cause the program to release the file descripter before the disconnect
is finished. hidraw_disconnect() has already set hidraw->exist to 0,
which makes hidraw_release() kfree the hidraw structure, which
hidraw_disconnect() continues to access and even tries to kfree again.
Similarly if a hidraw_release() occurs after setting hidraw->exist to 0,
the same thing can happen.
This is fixed by expanding the mutex critical section to cover the whole
function from setting hidraw->exist to 0 to freeing the hidraw
structure, preventing a hidraw_release() from interfering.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Tested-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The IDEACOM 6650 multitouch chip, present in various all-in-one computers,
uses the serial version of the HID multitouch protocol. No existing class
supports this.
In principle, the new MT_CLS_SERIAL should work for other
serial panels as well, perhaps including some eGalax panels.
Signed-off-by: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
On platforms with no iCRU support don't print two, (possibly conflicting),
"NMI occurred" messages when the firmware is unable to source the NMI.
Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow
KDUMP to succeed even on NMIs that are unknown to the platform firmware.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the passed watchdog_device instead of the static global variable when
testing and setting the status in watchdog_ping, watchdog_start, and
watchdog_stop. Note that the callers of these functions are actually
passing the static global variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In systems where there is no hardware signal from the processor to the
PMIC to initiate the final power off sequence we must initiate the
shutdown with a register write to the PMIC. Support such systems in the
driver. Since this may prevent a full shutdown of the system platform
data is used to enable the feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'drm-nouveau-next' of git://git.freedesktop.org/git/nouveau/linux-2.6: (353 commits)
drm/nouveau: remove allocations from gart populate() hook
drm/nvc0/fb: slightly improve PMFB intr handling, move out of nvc0_graph.c
drm/nvc0/fifo: avoid touching missing subfifos
drm/nvd9/disp: bail out of mode_set_base if no fb bound to crtc
drm/nvd9/disp: stub some more api hooks so we don't oops on resume
drm/nouveau: fix printk typo in ioremap failure path
drm/nvc0/pm: minor clock readback fixes
drm/nv40/pm: execute memory reset script from vbios
drm/nv50/gr: refactor initialisation
drm/nouveau: if requested, try harder at disabling sysmem pushbufs
drm/nv50/gr: enable ctxprog xfer only when we need it to save power
drm/nouveau/dp: add support for displayport table 0x30
drm/nouveau/dp: return master dp table pointer too when looking up encoder
drm/nouveau/bios: simplify U/d table hash matching func to just match
drm/nouveau/dp: preserve non-pattern bits in DP_TRAINING_PATTERN_SET
drm/nvc0/gr: remove MODULE_FIRMWARE() lines
drm/nouveau/dp: use alternate lane mask for nvaf
drm/nouveau/dp: link rate scripts are selected with a comparison table
drm/nv40/pm: write nv40-specific reclocking routines
drm/nv40/pm: parse geometric delta clock from vbios
...
Now that the HWMOD fmwk handles the fcks of DSS modules properly, the
DSS driver no longer needs to explicitely enable/disable the fck.
This patch removes the enables/disables of fck from dispc, dsi and dss.
The clk_get(fck) is still needed there, as the modules need to know the
frequency of the clock.
For hdmi and venc this patch also removes the clk_get(fck), as they
don't need the clock at all.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using the multi_tx_table to map possible Tx queues to Tx rings
we can just do simple subtraction for the unlikely event that the Tx queue
provided exceeds the number of Tx rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since igb only uses advanced descriptors we might as well just use an IGB
specific define and drop the _ADV suffix for the descriptor declarations.
In addition this can be further reduced by assuming that it will be working
on pointers since that is normally how the Tx descriptors are handled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the function names in the hot path are carrying an extra "_adv"
suffix on the end of them to represent the fact that they are using
advanced descriptors instead of legacy descriptors. However since all igb
uses are advanced descriptors adding the extra suffix doesn't really add
any additional data. Since this is the case it is easiest to just drop the
suffix and save us from having to store the extra characters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to be a general cleanup and performance improvement
for clean_rx_irq. The previous patch should have updated the allocation so
that the rings can be treated as read-only within the clean_rx_irq
function. In addition I am re-ordering the operations such that several
goals are accomplished including reducing the overhead for packet
accounting, reducing the number of items on the stack, and improving
overall performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve performance by splitting the Tx and Rx
rings into 3 sections. The first is primarily a read only section
containing basic things like the indexes, a pointer to the dev and netdev
structures, and basic information. The second section contains the stats
and next_to_use and next_to_clean values. The third section is primarily
unused values that can just be placed at the end of the ring and are not
used in the hot path.
The adapter structure has several sections that are read in the hot path.
In order to improve performance there I am combining the frequent read
hot path items into a single cache line.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to streamline the Rx buffer allocation and cleanup.
This is accomplished by reducing the number of writes by only having the Rx
descriptor ring written by software during allocation, and it will only be
read during cleanup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes support for single buffer mode from igb and makes the
driver function in packet split always. The advantage to doing this is
that we can reduce total memory allocation overhead significantly as we
will only need to allocate one 1K slab per packet and then make use of a
reusable half page instead of allocating a 2K slab per packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the max_frame_size in order account for an optional
VLAN tag. In order to support this we must also increase the
MAX_STD_JUMBO_FRAME_SIZE to account for the 4 extra bytes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the RXDCTL and TXDCTL configurations and optimizes RX
performance by allowing back write-backs on all hardware other than 82576.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
dma_async_device_register will re-init chan_id and chancnt,
so whatever chan_id and chancnt are set in drivers, they will
be re-written by dma_async_device_register.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Yong Wang <yong.y.wang@intel.com>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: Pelagicore AB <info@pelagicore.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since some somewhat questionable changes a while back, TTM provides a
completely empty array of struct dma_address that stays around for the
entire lifetime of the TTM object.
Lets use this array, *always*, rather than wasting yet more memory on
another array who's purpose is identical, as well as yet another bool array
of the same size saying *which* of the previous two arrays to use...
This change will also solve the high order allocation failures seen by
some people while using nouveau.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch adds instructions to ctxprog and by doing, impacts context
switching performance. My testcase showed a 1% performance cost using
glxgears that is a context-switch bound application.
Please test and report bugs/performance/power/other.
Many thanks to Maxim Levitsky for his dedicated work on lowering power
consumption with nouveau.
More patches are coming thanks to his work:
https://bugs.freedesktop.org/show_bug.cgi?id=37922
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
