Written from observations of my NVD9's vbios, completely untested due to
my NVD9 lacking actual DisplayPort connectors..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Will need to be able to distinguish 2.0/2.1 from 3.0 soon. Also, move
the vbios parsing to nouveau_dp where it belongs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We don't use these by default anymore, and there's been complaints from a
number of places thinking that the firmware blobs are required still.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not 100% perfect yet, but a good start towards what it'll look like in the
end.
Actually seems stable on a NV44 I have here, as much as running around OA
for a fair amount of time constantly switching between performance levels
can prove..
My NV49 isn't quite so happy, and semaphores mess up somehow (sometimes) as
a result of the memory reclocking.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This changes the meaning of what we reported as "core" clock previously.
The shader/rop units are allegedly supposed to be run at the base clock
listed in the perf table, while the geometric clock can be bumped from
this value on some boards.
So that we can report both, we'll report the base clock as "shader" (since
the shaders *do* run at it), and the geometric clock as "core".
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not used currently, but it will be used in preference to pre-determined
lane/bandwidth numbers at a later point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
I'm sure that out there somewhere, someone will need this. We currently
haven't seen an example of LVDS being on a non-0 SOR so far though.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds a udbg and an hvc console backend for supporting a console
using the OPAL console interfaces.
On OPAL v1 we have hvc0 mapped to whatever console the system was
configured for (network or hvsi serial port) via the service
processor.
On OPAL v2 we have hvcN mapped to the Nth console provided by OPAL
which generally corresponds to:
hvc0 : network console (raw protocol)
hvc1 : serial port S1 (hvsi)
hvc2 : serial port S2 (hvsi)
Note: At this point, early debug console only works with OPAL v1
and shouldn't be enabled in a normal kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We used to overwrite with CONFIG_CMDLINE if we found a chosen
node but failed to get bootargs out of it or they were empty,
unless CONFIG_CMDLINE_FORCE is set.
Instead change that to overwrite if "data" is non empty after
the bootargs check. It allows arch code to have other mechanisms
to retrieve the command line prior to parsing the device-tree.
Note: CONFIG_CMDLINE_FORCE case should ideally be handled elsewhere
as it won't work as it-is if the device-tree has no /chosen node
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: devicetree-discuss@lists-ozlabs.org
CC: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The HW will only accept the DMA_FROM_MEMORY class for DMA_SEMAPHORE without
asking the driver to intervene.
It appears that semaphores will work correctly even without DMA_IN_MEMORY,
so lets avoid the large amount of interrupts generated by x-chan sync.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
NV30: Create framework for memtm
NV50: Improve reg creation,
NV50: Use P.version instead of card codename/stepping,
NVC0: Initial memtiming code for Fermi,
Renamed regs for consistency,
Overall redesign to improve readability,
Avoid kfree on null-pointer
Signed-off-by: Roy Spliet <r.spliet@student.tudelft.nl>
If we support PGPIO interrupts, and know a hotplug GPIO tag for a
connector we use HPD, otherwise POLL_CONNECT.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The nouveau hwmon temperature support currently only functions when hwmon is
compiled into the kernel. There's no reason why this shouldn't also work when
both hwmon and nouveau are modularised (as is the case with Slackware's stock
kernels).
Signed-off-by: Ken Milmore <ken.milmore@googlemail.com>
Reviewed-by: Martin Peres <martin.peres@ensi-bourges.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Takes a gamble and presumes that we can safely store something random in
OR_MODE_CTRL+4, the hw doesn't seem to mind...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
VBIOS does more than this, as does nv50/nvc0 driver in nouveau. Traces
of the NVIDIA binary driver however, show pretty much just this being
done... Seems to work for me, it'll be fine for the moment.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
