Currently pm_genpd_poweroff() discards error codes returned by
the PM domain's .power_off() callback, because it's safer to always
regard the domain as inaccessible to drivers after a failing
.power_off(). Still, there are situations in which the low-level
code may want to indicate that it doesn't want to power off the
domain, so allow it to do that by returning -EBUSY from .power_off().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make pd_power_down_a3rv() use genpd_queue_power_off_work() to queue
up the powering off of the A4LC domain to avoid queuing it up when
it is pending.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Callback based iteration is cumbersome and much less useful than
for_each_*() iterator. This patch implements for_each_mem_pfn_range()
which replaces work_with_active_regions(). All the current users of
work_with_active_regions() are converted.
This simplifies walking over early_node_map and will allow converting
internal logics in page_alloc to use iterator instead of walking
early_node_map directly, which in turn will enable moving node
information to memblock.
powerpc change is only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20110714074610.GD3455@htj.dyndns.org
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Avoid telling users to use xvde and onwards when using xvde.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
These were intended to avoid the namespace clash when representing
emulated IDE and SCSI devices. However that seems to confuse users
more than expected (a disk defined as sda becomes xvde).
So for now go back to the scheme which does no adjustments. This
will break when mixing IDE and SCSI names in the configuration of
guests but should be by now expected.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reset card->tx_dma_progress when lv1_net_start_tx_dma() fails or it
won't send anything afterwards anymore
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert to a proper state when gelic_card_kick_txdma() fails:
- Don't trigger BUG_ON when releasing the unsent tx descriptor
- Reset the tx chain head since the tail was not modified and
hence not in sync
- Unlink the released descriptor bus address from its predecessor
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Change FW dump capture mask to a defult value, instead of using the recommended
value from the FW. This was done to keep the capture mask consistent with other
function drivers.
o Update driver version to 5.0.21
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Defined error code such as fw not responding, test already running and
cable not connected.
o Check Fw capability before performing loopback test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as skb is given to hardware, TX completion can free skb under us.
Therefore, we should update dev stats before kicking the device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC learning is required in bridge mode.
During bridge mode device will be put in promiscous mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added QME8242-k 10GbE Dual Port Mezzanine Card to supported card info.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip reset logic (IDC logic) has changed with fw dump support.
This broked compatibility with driver using older IDC logic.
Changes to make it compatible with drivers using older IDC logic.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scratchpad location that we were reading from has not been
initialized yet during ->probe(), so we were getting inaccurate
information.
Update version to 2.1.10.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to help debug issues related to management firmware.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to allow iSCSI connection to fail faster instead of waiting for the
long timeout.
Update version to 2.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest bnx2x driver uses different CID for the iSCSI rings, so
we need to pass it in the ring init data. The rx ring is also
zeroed out to prevent stale DMA addresses from being used after
shutdown.
The same cp local variable redefined inside the else branch is
also eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHIP_2_PORT_MODE was not set correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested by Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver state (and power source) is being more intensely
scrutinized, we need to make sure it is correct 100% of the time. This
patch finds and fixes all dangling power state transitions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to update the status of the function to a common
location to the critical section added in the previous patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that performs the power source switching will need to consider
the status of the other devices before making any switches. The status
updates and power source switching will need to be an atomic operation,
so a critical section will be needed. This patch establishes the
critical section through a CPMU mutex.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 devices will need to know exactly what function number they are so
that they can communicate their status to the other functions. In a KVM
environment, the function number of a device presented by the kernel
might not be the true function number, so an alternative method to
determine the function number is needed.
This patch used to contain an implementation for the alternative method,
but recently we discovered a hardware bug that renders it incorrect.
While new method is not yet known, it is still useful to consolidate the
code that determines the PCI function to one location and use the
results throughout the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently pci_set_power_state() does not return useful return codes for
transitions to the D0 power state. If a device refuses to go into D0,
the PCI layer issues a warning but returns success.
Entering into D0 is a requirement for correct operation of tg3 devices
though. If the PCI layer should be changed to return an error code for
this type of failure, the tg3 driver would be interested in catching it
and reacting to it. This patch makes the necessary modifications.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver is going to require memory mapped register access much
sooner than before. This patch makes sure the device is in the D0 power
state as soon as possible, and moves the code that enables the memory
arbiter outside tg3_get_eeprom_hw_cfg() where it can be more easily
monitored.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch will require the driver to communicate with the APE
much sooner than before. This patch make sure the APE registers are
memory mapped and that the ENABLE_APE bit is set before the first use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 1c48a5c93, "dt: Eliminate
of_platform_{,un}register_driver", the xsysace driver attempts to
register two platform_drivers with the same name, which a) doesn't
work, and b) isn't necessary. This patch merges the two
platform_drivers.
Reported-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
hid_hw_stop() must be called in ax_probe() error path if hid_hw_start()
was successful.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We've tried several times to make this machine 'just work', but every
patch that does causes many other machines to fail. This adds a quirk
which special cases this hardware and forces ssc to be
disabled. There's no way to override this from the command line; that
would be a significantly more invasive change.
This patch fixes#36656 on fdo bugzilla:
https://bugs.freedesktop.org/show_bug.cgi?id=36656
Signed-off-by: Keith Packard <keithp@keithp.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36656
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the fence of the new frontbuffer, if any.
Generating a new fence could cause us to wait for completely unrelated
rendering to finish before performing the flip.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of ssh://master.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6: (52 commits)
drm/i915: provide module parameter description
drm/i915: add module parameter compiler hints
drm/i915/bios: Avoid temporary allocation whilst searching for downclock
drm/i915: Cache GT fifo count for SandyBridge
i915: Fix opregion notifications
drm/i915: TVDAC_STATE_CHG does not indicate successful load-detect
drm/i915: Select correct pipe during TV detect
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable i915 frame buffer compression by default
drm/i915: Share the common work of disabling active FBC before updating
drm/i915: Perform intel_enable_fbc() from a delayed task
drm/i915: Disable FBC across page-flipping
drm/i915: Set persistent-mode for ILK/SNB framebuffer compression
drm/i915: Use of a CPU fence is mandatory to update FBC regions upon CPU writes
drm/i915: Remove vestigial pitch from post-gen2 FBC control routines
drm/i915: Replace direct calls to vfunc.disable_fbc with intel_disable_fbc()
drm/i915: Only export the generic intel_disable_fbc() interface
drm/i915: Enable GPU reset on Ivybridge.
...
Trivial fix for 80 char line overflow in drivers/acpi/pci_root.c
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Len Brown <len.brown@intel.com>
Use battery->lock in sysfs_remove_battery() to make
checking, removing, and clearing bat.dev atomic.
This is necessary because sysfs_remove_battery() may
be invoked concurrently from different paths.
https://bugzilla.kernel.org/show_bug.cgi?id=35642
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In the commit 25be5821, add the refresh sysfs when system resumes
from suspending. But it didn't check that the battery exists. This
will cause battery sysfs files added when the battery doesn't exist.
This patch add the check before refreshing.
https://bugzilla.kernel.org/show_bug.cgi?id=35642
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The Commit 25be58215 has added a PM notifier to refresh the sys in order
to deal with the unit change of the Battery Present Rate. But it just
consided the suspend situation. The problem also will happen during the
hibernation according the bug 28192.
https://bugzilla.kernel.org/show_bug.cgi?id=28192
This patch adds the hibernation process and fix the bug.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is cosmetic only, and makes no functional change.
Since the acpi_battery_quirks has been deleted, rename
acpi_battery_quirks2 with acpi_battery_quirks to clean the code.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is for some machines which report the battery current
as a 16-bit signed negative when it is charging. This is caused
by DSDT bug. The commit bc76f90b8a
has resolved the problem for Acer laptops. But some other machines
also have such problem.
https://bugzilla.kernel.org/show_bug.cgi?id=33722
Since it is improper that the current is above 32A on laptops
whether on AC or on battery, this patch is to check the current and
take its absolute value as current and producing a message when it
is negative in s16.
Remove Acer quirk, as this workaround handles Acer too.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is cosmetic only, and makes no functional change.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We can only sort the _TSS return package if there is no _PSS
in the same scope. This is because if _PSS is present, the ACPI
specification dictates that the _TSS Power Dissipation field is
to be ignored, and therefore some BIOSs leave garbage values in
the _TSS Power field(s). In this case, it is best to just return
the _TSS package as-is.
Reported-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Runtime option can be used to disable return value repair if this
is causing a problem on a particular machine.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Affects both iASL and core ACPICA.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now, only allow "SSDT" "OEM", and a null signature.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
