APEI firmware first mode must be turned on explicitly on some
machines, otherwise there may be no GHES hardware error record for
hardware error notification. APEI bit in generic _OSC call can be
used to do that, but on some machine, a special WHEA _OSC call must be
used. This patch adds the support to that WHEA _OSC call.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In APEI firmware first mode, hardware error is reported by hardware to
firmware firstly, then firmware reports the error to Linux in a GHES
error record via POLL/SCI/IRQ/NMI etc.
This may result in some issues if OS has no full APEI support. So
some firmware implementation will work in a back-compatible mode by
default. Where firmware will only notify OS in old-fashion, without
GHES record. For example, for a fatal hardware error, only NMI is
signaled, no GHES record.
To gain full APEI power on these machines, APEI bit in generic _OSC
call can be specified to tell firmware that Linux has full APEI
support. This patch adds the APEI bit support in generic _OSC call.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some machine may have broken firmware so that GHES and firmware first
mode should be disabled. This patch adds support to that.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
GHES (Generic Hardware Error Source) is used to process hardware error
notification in firmware first mode. But because firmware first mode
can be turned on but can not be turned off, it is unreasonable to
unload the GHES module with firmware first mode turned on. To avoid
confusion, this patch makes GHES can be enabled/disabled in
configuration time, but not built as module and unloaded at run time.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch changes APEI EINJ and ERST to use apei_exec_run for
mandatory actions, and apei_exec_run_optional for optional actions.
Cc: Thomas Renninger <trenn@novell.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some actions in APEI ERST and EINJ tables are optional, for example,
ACPI_EINJ_BEGIN_OPERATION action is used to do some preparation for
error injection, and firmware may choose to do nothing here. While
some other actions are mandatory, for example, firmware must provide
ACPI_EINJ_GET_ERROR_TYPE implementation.
Original implementation treats all actions as optional (that is, can
have no instructions), that may cause issue if firmware does not
provide some mandatory actions. To fix this, this patch adds
apei_exec_run_optional, which should be used for optional actions.
The original apei_exec_run should be used for mandatory actions.
Cc: Thomas Renninger <trenn@novell.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
printk is used by GHES to report hardware errors. Normally, the
printk will be ratelimited to avoid too many hardware error reports in
kernel log. Because there may be thousands or even millions of
corrected hardware errors during system running.
That is different for fatal hardware error, because system will go
panic as soon as possible, there will be no more than several error
records. And these error records are valuable for system fault
diagnosis, so they should not be ratelimited.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When we debug ERST table with erst-dbg, if the error record in ERST
table is too long(>4K), it can't be read out. So this patch increases
the buffer size to 16K to ensure such error records can be read from
ERST table.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
erst_dbg module can not work when ERST is disabled. So disable module
loading to provide clearer information to user.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The firmware on some machine will report duplicated hardware error
source ID in HEST. This is considered a firmware bug. To provide
better warning message, this patch adds duplicated hardware error
source ID detecting and corresponding printk.
This patch fixes#37412 on kernel bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=37412
Reported-by: marconifabio@ubuntu-it.org
Signed-off-by: Huang Ying <ying.huang@intel.com>
Tested-by: Mathias <janedo.spam@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In general, the mxs-dma users get separate irq for each channel,
but gpmi is special one which has only one irq shared by all gpmi
channels. It causes mxs_dma channel allocation function fail for
all other gpmi channels except the first one calling into the
function.
The patch gets request_irq call skipped for NO_IRQ case, and leaves
this gpmi specific quirk to gpmi driver to sort out. It will fix
above problem if gpmi driver sets chan_irq as gpmi irq for only one
channel and NO_IRQ for all the rest channels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While testing Per Forlins MMC speed improvements I noticed a
semantic bug in the COH901318 driver: it will write to channel
registers in the prep_slave_sg() function, instead of deferring
it to later, breaking the assumption from the drivers to be able
to queue up new jobs while another job is running. Fix this by
storing up the initial register writes in the job descriptors
and write them to hardware when we process the descriptor
instead. Now the stress tests work.
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As Simon reported, digital TV broke with mt20xx tuner due to
commit ad020dc2fe.
The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.
Reported-by: Simon Arlott <simon@fire.lp0.eu>
Tested-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch which addresses a race condition in the DVB core
related to closing/reopening the DVB frontend device in quick
succession. This is the reason that devices such as the HVR-1300,
HVR-3000, and HVR-4000 have been failing to scan properly under MythTV
and w_scan.
The gory details of the race are described in the patch.
Devin
There is a race condition exhibited when channel scanners such as w_scan and
MythTV quickly close and then reopen the frontend device node.
Under normal conditions, the behavior is as follows:
1. Application closes the device node
2. DVB frontend ioctl calls dvb_frontend_release which sets
fepriv->release_jiffies
3. DVB frontend thread *eventually* calls dvb_frontend_is_exiting() which
compares fepriv->release_jiffies, and shuts down the thread if timeout has
expired
4. Thread goes away
5. Application opens frontend device
6. DVB frontend ioctl() calls ts_bus_ctrl(1)
7. DVB frontend ioctl() creates new frontend thread, which calls
dvb_frontend_init(), which has demod driver init() routine setup initial
register state for demod chip.
8. Tuning request is issued.
The race occurs when the application in step 5 performs the new open() call
before the frontend thread is shutdown. In this case the ts_bus_ctrl() call
is made, which strobes the RESET pin on the demodulator, but the
dvb_frontend_init() function never gets called because the frontend thread
hasn't gone away yet. As a result, the initial register config for the demod
is *never* setup, causing subsequent tuning requests to fail.
If there is time between the close and open (enough for the dvb frontend
thread to be torn down), then in that case the new frontend thread is created
and thus the dvb_frontend_init() function does get called.
The fix is to set the flag which forces reinitialization if we did in fact
call ts_bus_ctrl().
This problem has been seen on the HVR-1300, HVR-3000, and HVR-4000, and is
likely occuring on other designs as well where ts_bus_ctrl() actually strobes
the reset pin on the demodulator.
Note that this patch should supercede any patches submitted for the
1300/3000/4000 which remove the code that removes GPIO code in
cx8802_dvb_advise_acquire(), which have been circulating by users for some
time now...
Canonical tracking this issue in Launchpad 439163:
Thanks to Jon Sayers from Hauppauge and Florent Audebert from Anevia S.A. for
providing hardware to test/debug with.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jon Sayers <j.sayers@hauppauge.co.uk>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When CONFIG_SND is not enabled, radio-sf16fmr2 build fails with:
so make this driver depend on SND.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the runtime config implementation forces the memory side
parameters to be the same as the peripheral side. Allow these to be
different, and check for misconfiguration.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Tested-by: Stefan Nilsson <stefan.xk.nilsson@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA40 is not a PrimeCell from ARM, but it still use the same
ID registers. So let's utilize the existing macros in the
PrimeCell header to identify manufacturer and revision of the IP
block instead of reinventing the wheel.
Cc: Robert Marklund <robert.marklund@stericsson.com>
Cc: Per Forlin <per.forlin@linaro.org>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This function may be initiated from IRQ context, so the allocation
must allocate NOWAIT memory.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ste_dma40 now implements issue_pending according to documentation.
Submit adds descriptos to a pending queue with are flushed down to the DMAC
at issue_pending.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
tx_submit will add descriptors to the pending queue. Issue pending
will then move the pending descriptors to the transfer queue.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The following symbols are needlessly defined global:
s5pv210_verify_speed
s5pv210_getspeed
Make them static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The following symbols are needlessly defined global:
exynos4_verify_speed
exynos4_getspeed
exynos4_set_clkdiv
Make them static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
By extension from the 667MHz based clocks currently supported add 100MHz
and 200MHz operating points. Due to a lack of documentation these have not
been confirmed as supported but by extension from the existing frequencies
they should be OK, and I've given them quite a bit of runtime testing.
The major risk is synchronization with the non-ARM clocks but as we
can't currently scale the ARM PLL the risk should be relatively low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
When system reboot, the CPUFREQ level should be 800MHz to prevent
system lockup.
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Voltage scaling accesses the MAX8998 regulators over bit-banged I2C
with lots of udelays. In the case of decreasing CPU speed, the
number of loops per us for udelay needs to be adjusted prior to
decreasing voltage to avoid delaying for up to 10X too long.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Without this lock the call to change the frequency for suspend could
switch to a new frequency while another thread was still changing the
cpu voltage.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Minimum 800MHz is needed to enter/exit suspend mode due to voltage mismatch.
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Relation has an additional symantics other than standard.
s5pv310_target funtion have below additional relation.
- DISABLE_FURTHER_CPUFREQ : disable further access to target
- ENABLE_FURTHER_CPUFRER : enable access to target
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The CPUFREQ_POSTCHANGE notification is used to update things that depend on
the system clock rates. Since this may include the interfaces used to talk
to the regulators do the notification before we try to update regulators
to reflect lowered system clock rate.
The voltage scaling is just a power optimisation and may not happen at all
so there's no concern about it not having completed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
At least some newer S3C6410 silicon supports operation up to 800MHz rather
than just 667MHz. Unfortunately I don't have access to any of documentation
of this other than some running systems, add a new cpufreq table entry for
this based on the behaviour of those systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The successive calls to clk_get each call clk_put in the case of failure,
but this is not done for subsequent error handling code. The calls to
clk_get are moved to the end of the function, and appropriate gotos are
added.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
According to discussion of the ARM arch subsystem migration,
ARM cpufreq drivers move to drivers/cpufreq. So this patch
adds Kconfig.arm for ARM like x86 and adds Samsung S5PV210
and EXYNOS4210 cpufreq driver compile in there.
As a note, otherw will be moved.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This is a straight code motion patch, there are no changes to the driver
itself. The Kconfig is left untouched as the ARM CPUfreq Kconfig is all
in one big block in arm/Kconfig and should be moved en masse rather than
being done piecemeal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dave Jones <davej@redhat.com>
acpi-cpufreq checks each CPU for aperf/mperf support, but only sets a
global flag. This will cause errors if some CPUs in the system don't
support the feature. Check boot_cpu_has() instead in order to make sure
that all CPUs support it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/evergreen: emit SQ_LDS_RESOURCE_MGMT for blits
agp/intel: Fix typo in G4x_GMCH_SIZE_VT_2M
drm/radeon/kms: fix typo in read_disabled vbios code
drm/radeon/kms: use correct BUS_CNTL reg on rs600
drm/radeon/kms: fix backend map typo on juniper
drm/radeon/kms: fix regression in hotplug
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
Alan Cox reported a missing check on the kmalloc return value for the
allocation of a temporary mode used for searching for the LVDS downlock
frequency. This allocation is roughly 200 bytes, a little too large to
friviously place on the stack. However, we can simply use the few bytes
we need stored within the original DVO timing data, skip the translation
and do the compare directly between the timing data rather than on a
mode, thus avoiding the need for any temporary allocations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.
On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.
This fixes a regression introduced in 3.0-rc1 by 08ee80cc39
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently, setting only legacy bitrates on 2.4GHz band
are supported. Mode 802.11b/g/bg is enabled based on
bitrates selection. If only CCK bitrates selected then
802.11b mode is enabled. If only OFDM bitrates are
selected then 802.11g mode is enabled. For both: CCK
and OFDM rates 802.11bg mixed mode is enabled.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using ieee80211_stop_queue, check the configured tx queue
limit before calling ieee80211_get_buffered_bc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
