This patch add DMA Coalescing which is a power-saving feature that
coalesces DMA writes in order to stay in a low-power state as much
as possible. Feature is disabled by default.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds functions and functions pointers to accommodate
differences between NVM interfaces and options for i350 devices,
82580 devices and the rest.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the EEE feature for i350 devices, enabled by default.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the driver string to match the PF driver string format.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel version string is off by a major version number since
new silicon was just introduced and also uses the wrong format for
the version postfix.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch splits the pll configs up on pll versions. This allows
easy adding of other known good pll values. Additionally it made it
possible to remove invalid configurations resulting in better
behaviour for such cases. The resulting clocks are no longer stored
resulting in some computing overhead on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The clocks can be easily recalculated by the timing and refresh value.
This brings us one step closer to removing VIAs modetable and use
generic ones and being easier extensible.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Before this patch only clocks that perfectly match were used and if
none existed this was not handled properly. This patch changes this
to always use the closest clock supported. This should behave like
before for clocks that have a perfect match but be much saner for
clocks which are slightly off.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes the direct lookup table for resolution+refresh and
pixclock by calculating this information from the mode table. Removes a
lot of dupllication and error potential by just doing a little more
calculations on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The function gen_74x164_remove and mc33880_remove are used only wrapped
by __devexit_p so define it using __devexit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to modules.pcimap:
pch_gpio 0x00008086 0x00008803 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
ml_ioh_gpio 0x000010db 0x0000802e 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
and fix a nearby typo, "do" that should have been "due"
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Controller will DMA only 32-bits of the tag per command
on completion if it knows we are only using 32-bit tags.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In process_nonindexed_cmd, hoist figuring of masked tag out of loop since
it is the same throughout.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
mpc23s17 is very similar to the mcp23s08, except that registers are 16bit
wide, so extend the interface to work with both variants.
The s17 variant also has an additional address pin, so adjust platform
data structure to support up to 8 devices per SPI chipselect.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The original dma_halt() function set the CA (channel abort) bit on both
the 83xx and 85xx controllers. This is incorrect on the 83xx, where this
bit means TEM (transfer error mask) instead. The 83xx doesn't support
channel abort, so we only do this operation on 85xx.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This merges the fsl_chan_ld_cleanup() function into the dma_do_tasklet()
function to reduce locking overhead. In the best case, we will be able
to keep the DMA controller busy while we are freeing used descriptors.
In all cases, the spinlock is grabbed two times fewer than before on
each transaction.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Previous to this patch, the dma_run_dependencies() function has been
called while holding desc_lock. This function can call tx_submit() for
other descriptors, which may try to re-grab the lock. Avoid this by
moving the descriptors to be cleaned up to a temporary list, and
dropping the lock before cleanup.
At the same time, add support for automatic unmapping of src and dst
buffers, as offered by the DMAEngine API.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Enabling poisoning in the dmapool API quickly showed that the DMA
controller was fetching descriptors that should not have been in use.
This has caused intermittent controller lockups during testing.
I have been unable to figure out the exact set of conditions which cause
this to happen. However, I believe it is related to the driver using the
hardware registers to track whether the controller is busy or not. The
code can incorrectly decide that the hardware is idle due to lag between
register writes and the hardware actually becoming busy.
To fix this, the driver has been reworked to explicitly track the state
of the hardware, rather than try to guess what it is doing based on the
register values.
This has passed dmatest with 10 threads per channel, 100000 iterations
per thread several times without error. Previously, this would fail
within a few seconds.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fixes some minor violations of the coding style. It also changes
the style of the device_prep_dma_*() function definitions so they are
identical.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds better tracking to link descriptor allocations, callbacks, and
frees. This makes it much easier to track errors with link descriptors.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes debugging the driver much easier when multiple channels are
running concurrently. In addition, you can see how much descriptor
memory each channel has allocated via the dmapool API in sysfs.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a purely cosmetic cleanup. It is nice to have related functions
right next to each other in the code.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The dmatest code relies on the DMAEngine API to automatically call
dma_unmap_single() on src buffers. The flags it passes are incorrect,
fix them.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We mark this as unused as well, given that I find no users,
at a later time we can determine to nuke this or not...
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
for i in $(find ./drivers/staging/ath6kl/ -name \*.[ch]) ; do \
sed -r -i -e "s/A_MEMCMP/memcmp/g" $i; done
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
for i in $(find ./drivers/staging/ath6kl/ -name \*.[ch]) ; do \
sed -r -i -e "s/A_MEMCPY/memcpy/g" $i; done
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The min() macro does strict type-checking so use min_t() instead
to silence a compile warning.
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the USB_STORAGE_ENE_UB6250 entry so that it stays under the
USB_STORAGE menu.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix ene_ub6250 build: it uses usb_storage driver interfaces, so it
should depend on USB_STORAGE.
ene_ub6250.c:(.text+0x14ff19): undefined reference to `usb_stor_reset_resume'
ene_ub6250.c:(.text+0x14ffb1): undefined reference to `usb_stor_bulk_transfer_buf'
ene_ub6250.c:(.text+0x14ffdd): undefined reference to `usb_stor_bulk_srb'
ene_ub6250.c:(.text+0x14fff1): undefined reference to `usb_stor_bulk_transfer_sg'
ene_ub6250.c:(.text+0x1503dd): undefined reference to `usb_stor_set_xfer_buf'
ene_ub6250.c:(.text+0x15048e): undefined reference to `usb_stor_access_xfer_buf'
ene_ub6250.c:(.text+0x150723): undefined reference to `usb_stor_probe1'
ene_ub6250.c:(.text+0x150795): undefined reference to `usb_stor_probe2'
ene_ub6250.c:(.text+0x1507af): undefined reference to `usb_stor_disconnect'
drivers/built-in.o:(.data+0x10224): undefined reference to `usb_stor_suspend'
drivers/built-in.o:(.data+0x10230): undefined reference to `usb_stor_pre_reset'
drivers/built-in.o:(.data+0x10234): undefined reference to `usb_stor_post_reset'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
