"buf" gets allocated twice in a row. It's the second allocation which
is correct. The first one should be removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: huajun li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Tegra2 USB controller doesn't properly deal with misaligned DMA
buffers, causing corruption. This is especially prevalent with USB
network adapters, where skbuff alignment is often in the middle of a
4-byte dword.
To avoid this, allocate a temporary buffer for the DMA if the provided
buffer isn't sufficiently aligned.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.
The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I picked up a new DAK-780EX(professional digitl reverb/mix system),
which use CH341T chipset to communication with computer on 3/2011
and the CH341T's vendor code is 1a86
Looking up the CH341T's vendor and product id's I see:
1a86 QinHeng Electronics
5523 CH341 in serial mode, usb to serial port converter
CH341T,CH341 are the products of the same company, maybe
have some common hardware, and I test the ch341.c works
well with CH341T
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On a laptop I see these errors on (most) resumes:
hub 3-0:1.0: over-current change on port 1
hub 3-0:1.0: over-current change on port 2
Since over-current conditions can disappear quite quickly it's better to
downgrade that message to debug level, recheck for an over-current
condition a little later and only print and over-current condition error
if that condition (still) exists when it's rechecked.
Add similar logic to hub over-current changes. (That code is untested,
as those changes do not occur on this laptop.)
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following section mismatch warning:
WARNING: drivers/usb/built-in.o(.data+0x74c): Section mismatch in reference from the variable ehci_atmel_driver to the function .init.text:ehci_atmel_drv_probe()
The variable ehci_atmel_driver references
the function __init ehci_atmel_drv_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support to iwlagn for off-channel TX. The
microcode API for this is a bit strange in that
it uses a hacked-up scan command, so the scan
code needs to change quite a bit to accomodate
that and be able to send it out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
defs.meshie.val.mesh_id is 32 chars long. It's not supposed to be NUL
terminated. This code puts a terminator on the end to make it easier to
print to sysfs. The problem is that if the mesh_id fills the entire
buffer the original code puts the terminator one spot past the end.
The way the original code was written, there was a check to make sure
that maxlen was less than PAGE_SIZE. Since we know that maxlen is at
most 34 chars, I just removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increasing the wait count makes the nf load pass in
most of the cases.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the delay to make sure the initialization of pll
passes.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set some GPIO pins to Pull-down mode to save power.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad
and covers even frames with PHY errors. When this flag is enabled, this message
shows up frequently during scanning or hardware resets:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
Since promiscuous mode is usually not particularly useful, yet enabled by
default by bridging (either used normally in 4-addr mode, or with hacks
for various virtualization software), we should sacrifice it for better
reliability during normal operation.
This patch leaves it enabled if there are active monitor mode interfaces, since
it's very useful for debugging.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While working on PS I've noticed elp_work is kicking rather often, and
sometimes the chip is put to sleep before 5ms delay expires. This
seems to happen because by the time wl1251_ps_elp_wakeup is called
elp_work might still be pending. After wakeup is done, the processing
may take some time, during which 5ms might expire and elp_work might
get scheduled. In this case, ss soon as 1st thread finishes work and
releases the mutex, elp_work will then put the device to sleep without
5ms delay. In addition 1st thread will queue additional elp_work
needlessly.
Fix this by cancelling work in wl1251_ps_elp_wakeup instead.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251_ps_set_elp() only does acx_sleep_auth call and takes the chip
from/to ELP, however all callers of wl1251_ps_set_mode() have already
taken the chip out of ELP and puts it back to ELP when they finish.
This makes ELP calls (and register writes they result in) superfluous.
So remove wl1251_ps_set_elp function and call acx_sleep_auth directly.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bit got lost somewhere along the way. Without this, panic.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This attribute, requested by Redhat, allows kexec-tools to know
whether the controller can honor the reset_devices kernel parameter
and actually reset the controller. For kdump to work properly it
is necessary that the reset_devices parameter be honored. This
attribute enables kexec-tools to warn the user if they attempt to
designate a non-resettable controller as the dump device.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch adds option 'bch' to nandsim, which can be used to enable
software BCH ECC (introduced in previous patches) and select BCH error
correction capability.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds software BCH ECC support to mtd, in order to handle recent
NAND device ecc requirements (4 bits or more).
It does so by adding a new ecc mode (NAND_ECC_SOFT_BCH) for use by board
drivers, and a new Kconfig option to enable BCH support. It relies on the
generic BCH library introduced in a previous patch.
When a board driver uses mode NAND_ECC_SOFT_BCH, it should also set fields
chip->ecc.size and chip->ecc.bytes to select BCH ecc data size and required
error correction capability. See nand_bch_init() documentation for details.
It has been tested on the following platforms using mtd-utils, UBI and
UBIFS: x86 (with nandsim), arm926ejs.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Because malloc/kzalloc may fail, we should check kmalloc/kzalloc return value
in sm_create_sysfs_attributes(), mtd/sm_rtl.c and do error handling.
Meanwhile, we should check sm_create_sysfs_attributes return value.
Signed-off-by: Xiaochen Wang <wangxiaochen0@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When page size is 4KiB, ecc.total is set to 8*9, and this causes
nand_write_page_hwecc() to read past the initialized part of the eccpos array,
which corrupts chip->oob_poi with bogus values from ecc_calc.
Fix this by creating a proper nand_ecclayout for 4KiB flashes.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The DaVinci NAND driver was including the mach-types.h header
file.
This prevented the DaVinci NAND driver from getting used
in a DSP only device. The linux port on c6x devices can make
use of the same driver and does not define a corresponding
header file.
This header file was required in the driver because earlier there was code
dependent on a machine_* check. This piece of code has now been factored out
and is in arch/arm/mach-davinci/aemif.c
Thus removing the header file is harmless
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use nand_scan_ident to unify the need of mtd member initilization
for both normal detection and keep configuration method.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Different NAND driver may require its unique detection. For pxa3xx_nand,
it use its self id database to get the necessary info.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make the interface simpler which could make both debug
and enhancement easier.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since we have rework the irq process, we don't need additional
delay in wait_for_event. Also write_cmd and __readid is also
discarded for the same reason.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Enable all irq when we start the nand controller, and
put all the transaction logic in the pxa3xx_nand_irq.
By doing this way, we could dramatically increase the
performance by avoid unnecessary delay.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The previous probe function is some kind of big part.
This patch seperate the resource allocation to keep the probe process
more clear than before.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
32-bit integers used in 'calc_speed()' may overflow and lead to
incorrect results. Use 64-bit integers instead.
Signed-off-by: David Lambert <dave@lambsys.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The number of corrected ECC errors should be reported since other MTD
systems make use of this information (such as UBI data scrubbing).
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New variable skip_initial_unlocking is added to the omap_onenand_platform_data.
This is used to inform the onenand driver to skip onenand unlocking when it
is initialized.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A new option ONENAND_SKIP_INITIAL_UNLOCKING is added. This allows
to disable initial onenand unlocking when the driver is initialized.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
OMAP-L137/AM17x has limited number of dedicated EMIFA
address pins, enough to interface directly to an SDRAM.
If a device such as an asynchronous flash needs to be
attached to the EMIFA, then either GPIO pins or a chip
select may be used to control the flash device's upper
address lines.
This patch adds support for the NOR flash on the OMAP-L137/
AM17x user interface daughter board using the latch-addr-flash
MTD mapping driver which allows flashes to be partially
physically addressed. The upper address lines are set by
a board specific code which is a separate patch.
Signed-off-by: David Griego <dgriego@mvista.com>
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a driver for allowing an mtd device to be used as a block device for
swapping. The block device is volatile, and the mapping of swapped pages
is not stored on flash.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Set max_discard_sectors to UINT_MAX.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a new background method into mtd_blktrans_ops, add background support
into mtd_blktrans_thread(), and add mtd_blktrans_cease_background().
If the mtd blktrans dev has the background support, the thread will
call background function when the request queue becomes empty. The background
operation may run as long as needs to until
mtd_blktrans_cease_background() tells to stop.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When initializing mtd->writebufsize, we must take into account
possible flash chip interleaving. Wrong writebufsize initialization
caused UBIFS recovery issues resulting in unmountable UBIFS file
system on NOR flash partitions.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New multiblock erase speed test is added to mtd_speedtest.
It consists of 2-, 4-, 8-, 16-, 32- and 64-blocks at once
multiblock erase tests.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
By default mtd_speedtest uses all the eraseblocks of the
MTD partition being tested. For large partitions a
smaller number is sufficient and makes running the test
quicker. For that reason, add a parameter 'count' to
specify the maximum number of eraseblocks to use for
testing.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In onenand_verify function the address can be writepage non-aligned.
When a page is read for comparing the right offset should be used
for "this->verify_buf" to get the right matching with compared
"buf" buffer.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When reading using the 4KiB page read function, I/O
errors could be ignored if more than 1 page was read
at a time.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In 'verify_bbt_descr()', first check the "bd" pointer, then
dereference it.
Comments amended by Artem.
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
