This device was tested with rt2870sta by setting new_id.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Brian Ormond <brian.ormond@oit.edu>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the original code the parenthesis are in the wrong position, so the
conditions are always true.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code called input_free_device(rmi4_data->input_dev) after
input_unregister_device(rmi4_data->input_dev) and that's a double free.
This is described in the comments to input_unregister_device().
The normal way to handle this is to make input_register_device() the
last function in the probe which can fail. That way you can avoid the
call to input_unregister_device() entirely.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Off by one
Signed-off-by: Phillip Simbwa <simbwa at gmail dot com>
Signed-off-by: Vipin Mehta <vmehta@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed the call to netif_stop_queue() in netvsc_probe() as
the queue is not initialized at that point and further call
to it after queue initialization is really not necessary.
This change was prompted after an upstream change went into
2.6.37 (netif_tx_stop_queue) that now checks if netif_stop_queue
is called before register with netdev is done.
This will eliminate the warning message to the log when hv_netvsc
driver starts up.
Signed-off-by: Abhishek Kane <v-abkane@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The channel callbacks are called directly from vmbus_event_dpc
which runs in tasklet context. These callbacks need to use
GFP_ATOMIC.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16701
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The block device does not create the proper symlink in sysfs because we
forgot to set up the gendisk structure properly. This patch fixes the
issue.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During suspend, Linus found that his machine would hang for 3 seconds,
and identified that intel_ring_buffer_wait() was the culprit:
"Because from looking at the code, I get the notion that
"intel_read_status_page()" may not be exact. But what happens if that
inexact value matches our cached ring->actual_head, so we never even
try to read the exact case? Does it _stay_ inexact for arbitrarily
long times? If so, we might wait for the ring to empty forever (well,
until the timeout - the behavior I see), even though the ring really
_is_ empty."
As the reported HEAD position is only updated every time it crosses a
64k boundary, whilst draining the ring it is indeed likely to remain one
value. If that value matches the last known HEAD position, we never read
the true value from the register and so trigger a timeout.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Presently the early console setup will be invoked for every device handed
off to he earlyprintk command line argument. In practice we can only
handle one, so this adds a sanity check to prevent clobbering the
existing active console.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The break flag timer is presently added through add_timer() via the
interrupt and error paths, where it is possible to send multiple breaks
in rapid succession and trigger the timer pending BUG_ON(). This moves
over to a mod_timer() instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently much of the error handling paths are inlined, stemming from a
time when they were much smaller. This simply brings them out of line and
leaves it up to the compiler. Given that some of these now contain nested
loops, it's pretty hard to justify the inlining regardless of the
footprint.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At the moment the request/release_port ops are no-ops with the port
remapping case tied in to the config_port op. This moves the remap logic
in to the request_port, balances it with unmapping in the port release,
and finally takes care of the mem region reservations.
All existing users are of the port autoconf variety, so we follow the
example of other drivers that wrap in to the port request by way of the
config op in the UART_CONFIG_TYPE case.
This is the first step towards fixing up conflicts with multiple users
of the same ports, as currently happens between sh-sci and spi_sh_sci.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Hangcheck and error recovery is only used by GEM.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We sometimes need to map between the virtio device and
the given pci device. One such use is OS installer that
gets the boot pci device from BIOS and needs to
find the relevant block device. Since it can't,
installation fails.
Instead of creating a top-level devices/virtio-pci
directory, create each device under the corresponding
pci device node. Symlinks to all virtio-pci
devices can be found under the pci driver link in
bus/pci/drivers/virtio-pci/devices, and all virtio
devices under drivers/bus/virtio/devices.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Tested-by: "Daniel P. Berrange" <berrange@redhat.com>
Cc: stable@kernel.org
arch/x86/lguest/boot.c: In function ‘lguest_init_IRQ’:
arch/x86/lguest/boot.c:824: error: macro "__this_cpu_write" requires 2 arguments, but only 1 given
arch/x86/lguest/boot.c:824: error: ‘__this_cpu_write’ undeclared (first use in this function)
arch/x86/lguest/boot.c:824: error: (Each undeclared identifier is reported only once
arch/x86/lguest/boot.c:824: error: for each function it appears in.)
drivers/lguest/x86/core.c: In function ‘copy_in_guest_info’:
drivers/lguest/x86/core.c:94: error: lvalue required as left operand of assignment
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Using cat or something to read from binary attributes would try to do an
additional read with offset equal to filesize. This resulted in an invalid
attribute error. This is fixed by giving the right answer instead of EINVAL.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch add support for Roccat Arvo keyboard. Arvo has 5 additional
configurable buttons and the ability to deactivate certain keys.
Userland tools can soon be found at http://sourceforge.net/projects/roccat
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To reduce the possibility of losing an interrupt in the handler due to a
race between an interrupt processing and disable/enable of interrupts,
enable MSIX one shot.
Also, add support for adaptive interrupt coalesing
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Masroor Vettuparambil <masroor.vettuparambil@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware PXE EPROM version detection is failing due to passing the
wrong parameter into firmware query function. Also, the version
printing function has an extraneous newline.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder the commands to be in the inverse order of their allocations
(instead of the random order they appear to be in), propagate return
code on errors from pci_request_region and register_netdev, reduce the
config_dev_cnt and total_dev_cnt counters on remove, and return the
correct error code for vdev->vpaths kzalloc failures. Also, prevent
leaking of vdev->vpaths memory and netdev in vxge_probe error path due
to freeing for these not occurring in vxge_device_unregister.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
There is no need to hold the firmware in memory.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The aggregation code currently doesn't implement the
buffer size negotiation. It will always request a max
buffer size (which is fine, if a little pointless, as
the mac80211 code doesn't know and might just use 0
instead), but if the peer requests a smaller size it
isn't possible to honour this request.
In order to fix this, look at the buffer size in the
addBA response frame, keep track of it and pass it to
the driver in the ampdu_action callback when called
with the IEEE80211_AMPDU_TX_OPERATIONAL action. That
way the driver can limit the number of subframes in
aggregates appropriately.
Note that this doesn't fix any drivers apart from the
addition of the new argument -- they all need to be
updated separately to use this variable!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered. Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.
In addtion, use the vif type instead of hardware opmode
when dealing with beacons.
Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because the sendbar variable was not reset to zero, the stack would send
Block ACK requests for all subframes following the one that failed, which
could mess up the receiver side block ack window.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the first TID in the first AC's list is not available for forming
a new aggregate (the BAW might not allow it), however other TIDs may have
data available for sending.
Prevent a slowdown of other TIDs by going through multiple entries until
we've either hit the last one or enough AMPDUs are pending in the hardware
queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 carrier leakage calibration related workaround on high
temperature is not applicable for AR9271.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k_hw assumes that caldata is valid only for
oper channel. But with ath9k_htc case, the caldata is
passed for all channels on hw_reset though we are not doing
calibration on that channel. So the oper channel's nf history
got cleared to default due to mismatch in channel flags.
This patch also saves some space.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
caldata's channel info is never filled with operating channel
info which is causing the operating channel's noise floor
history buffer is reset to default nf during channel change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rx error bit parsing was changed to consider PHY errors and various
decryption errors separately. While correct according to the documentation,
this is causing spurious decryption error reports in some situations.
Fix this by restoring the original order of the checks in those places,
where the errors are meant to be mutually exclusive.
If a CRC error is reported, then MIC failure and decryption errors
are irrelevant, and a PHY error is unlikely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eeprom read functions are of bool type and not int.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since baseband hangs are rare, but the hang check function has a high
false positive rate in some situations, we need to add more reliable
indicators.
In AP mode we can use blocked beacon transmissions as an indicator,
they should be rare enough.
In station mode, we can skip the hang check entirely, since a true
hang will trigger beacon loss detection, and mac80211 will rescan,
which leads to a hw reset that will bring the hardware back to life.
To make this more reliable, we need to skip fast channel changes
if the hardware appears to be stuck.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There might be some old stale data left, which could confuse tracking
of pending tx frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txtid->seq_start may not always be up to date, when there is HT non-AMPDU
traffic just before starting an AMPDU session. Relying on txtid->seq_next
is better, since it is also used to generate the sequence numbers for
all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a tid pointer is passed to ath_tx_send_normal(), it increases the
starting sequence number for the next AMPDU action frame, which should
only be done if the sequence number assignment is fresh. In this case
it is clearly not.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basically fix and fine-tune RT3070/RT3071/RT3090 chip RF initial value
when call rt2800_init_rfcsr
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PCI/PCIE radio off behavior is different from SOC/USB.
They mainly use MCU command to disable DMA, TX/RX and enter power saving mode.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For USB devices, reading the EEPROM data can be offloaded
to the target. Use multiple register reads to take advantage
of this feature to reduce initialization time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would decrease latency in reading bulk registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
set_key callback is defined for mac80211 to install keys for HW crypto in AP
mode. Driver currently falls back to SW crypto in STA mode. Add support to
configure the keys appropriately in the hardware after the set_key routine is
called.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hw crypto is enabled, set rx status flags appropriately depending on
whether hw crypto is enabled for a particular bss.
Also report MIC errors to mac80211, so that counter measures can be
initiated
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: yogesh powar <yogeshp@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different tail pads will be needed for crypto depending on the crypto
mode. Add support to encapsulate the packets with appropriate pad
value.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add capability to add_dma_header to support padding at tail of the data
packet to be transmitted when crypto is enabled. Padding is required for
adding crypto information in data packets for supporting 802.11 security
modes.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>