commit fdb1ada57c upstream.
The _CRS ACPI resources table has 2 entries for the host wakeup GPIO,
the first one being a regular GpioIo () resource while the second one
is a GpioInt () resource for the same pin.
The acpi_gpio_mapping table used by vsc-tp.c maps the first Gpio ()
resource to "wakeuphost-gpios" where as the second GpioInt () entry
is mapped to "wakeuphostint-gpios".
Using "wakeuphost" to request the GPIO as was done until now, means
that the gpiolib-acpi code does not know that the GPIO is active-low
as that info is only available in the GpioInt () entry.
Things were still working before due to the following happening:
1. Since the 2 entries point to the same pin they share a struct gpio_desc
2. The SPI core creates the SPI device vsc-tp.c binds to and calls
acpi_dev_gpio_irq_get(). This does use the second entry and sets
FLAG_ACTIVE_LOW in gpio_desc.flags .
3. vsc_tp_probe() requests the "wakeuphost" GPIO and inherits the
active-low flag set by acpi_dev_gpio_irq_get()
But there is a possible scenario where things do not work:
1. - 3. happen as above
4. After requesting the "wakeuphost" GPIO, the "resetfw" GPIO is requested
next, but its USB GPIO controller is not available yet, so this call
returns -EPROBE_DEFER.
5. The gpio_desc for "wakeuphost" is put() and during this the active-low
flag is cleared from gpio_desc.flags .
6. Later on vsc_tp_probe() requests the "wakeuphost" GPIO again, but now it
is not marked active-low.
The difference can also be seen in /sys/kernel/debug/gpio, which contains
the following line for this GPIO:
gpio-535 ( |wakeuphost ) in hi IRQ ACTIVE LOW
If the second scenario is hit the "ACTIVE LOW" at the end disappears and
things do not work.
Fix this by requesting the GPIO through the "wakeuphostint" mapping instead
which provides active-low info without relying on acpi_dev_gpio_irq_get()
pre-populating this info in the gpio_desc.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2316918
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Fixes: 566f5ca976 ("mei: Add transport driver for IVSC device")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250214212425.84021-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91d44c1afc upstream.
Fixed a possible UAF problem in driver_override_show() in drivers/cdx/cdx.c
This function driver_override_show() is part of DEVICE_ATTR_RW, which
includes both driver_override_show() and driver_override_store().
These functions can be executed concurrently in sysfs.
The driver_override_store() function uses driver_set_override() to
update the driver_override value, and driver_set_override() internally
locks the device (device_lock(dev)). If driver_override_show() reads
cdx_dev->driver_override without locking, it could potentially access
a freed pointer if driver_override_store() frees the string
concurrently. This could lead to printing a kernel address, which is a
security risk since DEVICE_ATTR can be read by all users.
Additionally, a similar pattern is used in drivers/amba/bus.c, as well
as many other bus drivers, where device_lock() is taken in the show
function, and it has been working without issues.
This potential bug was detected by our experimental static analysis
tool, which analyzes locking APIs and paired functions to identify
data races and atomicity violations.
Fixes: 1f86a00c11 ("bus/fsl-mc: add support for 'driver_override' in the mc-bus")
Cc: stable <stable@kernel.org>
Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com>
Link: https://lore.kernel.org/r/20250118070833.27201-1-chenqiuji666@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9dc8fb3af upstream.
Fix a goof where KVM sets CPUID.0x80000022.EAX to CPUID.0x80000022.EBX
instead of zeroing both when PERFMON_V2 isn't supported by KVM. In
practice, barring a buggy CPU (or vCPU model when running nested) only the
!enable_pmu case is affected, as KVM always supports PERFMON_V2 if it's
available in hardware, i.e. CPUID.0x80000022.EBX will be '0' if PERFMON_V2
is unsupported.
For the !enable_pmu case, the bug is relatively benign as KVM will refuse
to enable PMU capabilities, but a VMM that reflects KVM's supported CPUID
into the guest could inadvertently induce #GPs in the guest due to
advertising support for MSRs that KVM refuses to emulate.
Fixes: 94cdeebd82 ("KVM: x86/cpuid: Add AMD CPUID ExtPerfMonAndDbg leaf 0x80000022")
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20250304082314.472202-3-xiaoyao.li@intel.com
[sean: massage shortlog and changelog, tag for stable]
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 189ecdb3e1 upstream.
Snapshot the host's DEBUGCTL after disabling IRQs, as perf can toggle
debugctl bits from IRQ context, e.g. when enabling/disabling events via
smp_call_function_single(). Taking the snapshot (long) before IRQs are
disabled could result in KVM effectively clobbering DEBUGCTL due to using
a stale snapshot.
Cc: stable@vger.kernel.org
Reviewed-and-tested-by: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/r/20250227222411.3490595-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 433265870a upstream.
Manually load the guest's DEBUGCTL prior to VMRUN (and restore the host's
value on #VMEXIT) if it diverges from the host's value and LBR
virtualization is disabled, as hardware only context switches DEBUGCTL if
LBR virtualization is fully enabled. Running the guest with the host's
value has likely been mildly problematic for quite some time, e.g. it will
result in undesirable behavior if BTF diverges (with the caveat that KVM
now suppresses guest BTF due to lack of support).
But the bug became fatal with the introduction of Bus Lock Trap ("Detect"
in kernel paralance) support for AMD (commit 408eb7417a
("x86/bus_lock: Add support for AMD")), as a bus lock in the guest will
trigger an unexpected #DB.
Note, suppressing the bus lock #DB, i.e. simply resuming the guest without
injecting a #DB, is not an option. It wouldn't address the general issue
with DEBUGCTL, e.g. for things like BTF, and there are other guest-visible
side effects if BusLockTrap is left enabled.
If BusLockTrap is disabled, then DR6.BLD is reserved-to-1; any attempts to
clear it by software are ignored. But if BusLockTrap is enabled, software
can clear DR6.BLD:
Software enables bus lock trap by setting DebugCtl MSR[BLCKDB] (bit 2)
to 1. When bus lock trap is enabled, ... The processor indicates that
this #DB was caused by a bus lock by clearing DR6[BLD] (bit 11). DR6[11]
previously had been defined to be always 1.
and clearing DR6.BLD is "sticky" in that it's not set (i.e. lowered) by
other #DBs:
All other #DB exceptions leave DR6[BLD] unmodified
E.g. leaving BusLockTrap enable can confuse a legacy guest that writes '0'
to reset DR6.
Reported-by: rangemachine@gmail.com
Reported-by: whanos@sergal.fun
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219787
Closes: https://lore.kernel.org/all/bug-219787-28872@https.bugzilla.kernel.org%2F
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: stable@vger.kernel.org
Reviewed-and-tested-by: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/r/20250227222411.3490595-5-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb71c79593 upstream.
Move KVM's snapshot of DEBUGCTL to kvm_vcpu_arch and take the snapshot in
common x86, so that SVM can also use the snapshot.
Opportunistically change the field to a u64. While bits 63:32 are reserved
on AMD, not mentioned at all in Intel's SDM, and managed as an "unsigned
long" by the kernel, DEBUGCTL is an MSR and therefore a 64-bit value.
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Cc: stable@vger.kernel.org
Reviewed-and-tested-by: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/r/20250227222411.3490595-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0eac42f5c upstream.
Mark BTF as reserved in DEBUGCTL on AMD, as KVM doesn't actually support
BTF, and fully enabling BTF virtualization is non-trivial due to
interactions with the emulator, guest_debug, #DB interception, nested SVM,
etc.
Don't inject #GP if the guest attempts to set BTF, as there's no way to
communicate lack of support to the guest, and instead suppress the flag
and treat the WRMSR as (partially) unsupported.
In short, make KVM behave the same on AMD and Intel (VMX already squashes
BTF).
Note, due to other bugs in KVM's handling of DEBUGCTL, the only way BTF
has "worked" in any capacity is if the guest simultaneously enables LBRs.
Reported-by: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: stable@vger.kernel.org
Reviewed-and-tested-by: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/r/20250227222411.3490595-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee89e80133 upstream.
Drop bits 5:2 from the guest's effective DEBUGCTL value, as AMD changed
the architectural behavior of the bits and broke backwards compatibility.
On CPUs without BusLockTrap (or at least, in APMs from before ~2023),
bits 5:2 controlled the behavior of external pins:
Performance-Monitoring/Breakpoint Pin-Control (PBi)—Bits 5:2, read/write.
Software uses thesebits to control the type of information reported by
the four external performance-monitoring/breakpoint pins on the
processor. When a PBi bit is cleared to 0, the corresponding external pin
(BPi) reports performance-monitor information. When a PBi bit is set to
1, the corresponding external pin (BPi) reports breakpoint information.
With the introduction of BusLockTrap, presumably to be compatible with
Intel CPUs, AMD redefined bit 2 to be BLCKDB:
Bus Lock #DB Trap (BLCKDB)—Bit 2, read/write. Software sets this bit to
enable generation of a #DB trap following successful execution of a bus
lock when CPL is > 0.
and redefined bits 5:3 (and bit 6) as "6:3 Reserved MBZ".
Ideally, KVM would treat bits 5:2 as reserved. Defer that change to a
feature cleanup to avoid breaking existing guest in LTS kernels. For now,
drop the bits to retain backwards compatibility (of a sort).
Note, dropping bits 5:2 is still a guest-visible change, e.g. if the guest
is enabling LBRs *and* the legacy PBi bits, then the state of the PBi bits
is visible to the guest, whereas now the guest will always see '0'.
Reported-by: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: stable@vger.kernel.org
Reviewed-and-tested-by: Ravi Bangoria <ravi.bangoria@amd.com>
Link: https://lore.kernel.org/r/20250227222411.3490595-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2653cd3b7 upstream.
When running SEV-SNP guests on a CPU that supports DebugSwap, always save
the host's DR0..DR3 mask MSR values irrespective of whether or not
DebugSwap is enabled, to ensure the host values aren't clobbered by the
CPU. And for now, also save DR0..DR3, even though doing so isn't
necessary (see below).
SVM_VMGEXIT_AP_CREATE is deeply flawed in that it allows the *guest* to
create a VMSA with guest-controlled SEV_FEATURES. A well behaved guest
can inform the hypervisor, i.e. KVM, of its "requested" features, but on
CPUs without ALLOWED_SEV_FEATURES support, nothing prevents the guest from
lying about which SEV features are being enabled (or not!).
If a misbehaving guest enables DebugSwap in a secondary vCPU's VMSA, the
CPU will load the DR0..DR3 mask MSRs on #VMEXIT, i.e. will clobber the
MSRs with '0' if KVM doesn't save its desired value.
Note, DR0..DR3 themselves are "ok", as DR7 is reset on #VMEXIT, and KVM
restores all DRs in common x86 code as needed via hw_breakpoint_restore().
I.e. there is no risk of host DR0..DR3 being clobbered (when it matters).
However, there is a flaw in the opposite direction; because the guest can
lie about enabling DebugSwap, i.e. can *disable* DebugSwap without KVM's
knowledge, KVM must not rely on the CPU to restore DRs. Defer fixing
that wart, as it's more of a documentation issue than a bug in the code.
Note, KVM added support for DebugSwap on commit d1f85fbe83 ("KVM: SEV:
Enable data breakpoints in SEV-ES"), but that is not an appropriate Fixes,
as the underlying flaw exists in hardware, not in KVM. I.e. all kernels
that support SEV-SNP need to be patched, not just kernels with KVM's full
support for DebugSwap (ignoring that DebugSwap support landed first).
Opportunistically fix an incorrect statement in the comment; on CPUs
without DebugSwap, the CPU does NOT save or load debug registers, i.e.
Fixes: e366f92ea9 ("KVM: SEV: Support SEV-SNP AP Creation NAE event")
Cc: stable@vger.kernel.org
Cc: Naveen N Rao <naveen@kernel.org>
Cc: Kim Phillips <kim.phillips@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Alexey Kardashevskiy <aik@amd.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20250227012541.3234589-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be45bc4eff upstream.
Enable/disable local IRQs, i.e. set/clear RFLAGS.IF, in the common
svm_vcpu_enter_exit() just after/before guest_state_{enter,exit}_irqoff()
so that VMRUN is not executed in an STI shadow. AMD CPUs have a quirk
(some would say "bug"), where the STI shadow bleeds into the guest's
intr_state field if a #VMEXIT occurs during injection of an event, i.e. if
the VMRUN doesn't complete before the subsequent #VMEXIT.
The spurious "interrupts masked" state is relatively benign, as it only
occurs during event injection and is transient. Because KVM is already
injecting an event, the guest can't be in HLT, and if KVM is querying IRQ
blocking for injection, then KVM would need to force an immediate exit
anyways since injecting multiple events is impossible.
However, because KVM copies int_state verbatim from vmcb02 to vmcb12, the
spurious STI shadow is visible to L1 when running a nested VM, which can
trip sanity checks, e.g. in VMware's VMM.
Hoist the STI+CLI all the way to C code, as the aforementioned calls to
guest_state_{enter,exit}_irqoff() already inform lockdep that IRQs are
enabled/disabled, and taking a fault on VMRUN with RFLAGS.IF=1 is already
possible. I.e. if there's kernel code that is confused by running with
RFLAGS.IF=1, then it's already a problem. In practice, since GIF=0 also
blocks NMIs, the only change in exposure to non-KVM code (relative to
surrounding VMRUN with STI+CLI) is exception handling code, and except for
the kvm_rebooting=1 case, all exception in the core VM-Enter/VM-Exit path
are fatal.
Use the "raw" variants to enable/disable IRQs to avoid tracing in the
"no instrumentation" code; the guest state helpers also take care of
tracing IRQ state.
Oppurtunstically document why KVM needs to do STI in the first place.
Reported-by: Doug Covelli <doug.covelli@broadcom.com>
Closes: https://lore.kernel.org/all/CADH9ctBs1YPmE4aCfGPNBwA10cA8RuAk2gO7542DjMZgs4uzJQ@mail.gmail.com
Fixes: f14eec0a32 ("KVM: SVM: move more vmentry code to assembly")
Cc: stable@vger.kernel.org
Reviewed-by: Jim Mattson <jmattson@google.com>
Link: https://lore.kernel.org/r/20250224165442.2338294-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c133ec0e57 upstream.
Raspberry Pi is a major user of those chips and they discovered a bug -
when the end of a transfer ring segment is reached, up to four TRBs can
be prefetched from the next page even if the segment ends with link TRB
and on page boundary (the chip claims to support standard 4KB pages).
It also appears that if the prefetched TRBs belong to a different ring
whose doorbell is later rung, they may be used without refreshing from
system RAM and the endpoint will stay idle if their cycle bit is stale.
Other users complain about IOMMU faults on x86 systems, unsurprisingly.
Deal with it by using existing quirk which allocates a dummy page after
each transfer ring segment. This was seen to resolve both problems. RPi
came up with a more efficient solution, shortening each segment by four
TRBs, but it complicated the driver and they ditched it for this quirk.
Also rename the quirk and add VL805 device ID macro.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://github.com/raspberrypi/linux/issues/4685
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=215906
CC: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250225095927.2512358-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bae8729e5 upstream.
The following FFI types are replaced compared to `core::ffi`:
1. `char` type is now always mapped to `u8`, since kernel uses
`-funsigned-char` on the C code. `core::ffi` maps it to platform
default ABI, which can be either signed or unsigned.
2. `long` is now always mapped to `isize`. It's very common in the
kernel to use `long` to represent a pointer-sized integer, and in
fact `intptr_t` is a typedef of `long` in the kernel. Enforce this
mapping rather than mapping to `i32/i64` depending on platform can
save us a lot of unnecessary casts.
Signed-off-by: Gary Guo <gary@garyguo.net>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20240913213041.395655-5-gary@garyguo.net
[ Moved `uaccess` changes from the next commit, since they were
irrefutable patterns that Rust >= 1.82.0 warns about. Reworded
slightly and reformatted a few documentation comments. Rebased on
top of `rust-next`. Added the removal of two casts to avoid Clippy
warnings. - Miguel ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27c7518e7f upstream.
In the last kernel cycle we migrated most of the `core::ffi` cases in
commit d072acda48 ("rust: use custom FFI integer types"):
Currently FFI integer types are defined in libcore. This commit
creates the `ffi` crate and asks bindgen to use that crate for FFI
integer types instead of `core::ffi`.
This commit is preparatory and no type changes are made in this
commit yet.
Finish now the few remaining/new cases so that we perform the actual
remapping in the next commit as planned.
Acked-by: Jocelyn Falempe <jfalempe@redhat.com> # drm
Link: https://lore.kernel.org/rust-for-linux/CANiq72m_rg42SvZK=bF2f0yEoBLVA33UBhiAsv8THhVu=G2dPA@mail.gmail.com/
Link: https://lore.kernel.org/all/cc9253fa-9d5f-460b-9841-94948fb6580c@redhat.com/
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 976e7e9bdc upstream.
For the ACPI backend of UCSI the UCSI "registers" are just a memory copy
of the register values in an opregion. The ACPI implementation in the
BIOS ensures that the opregion contents are synced to the embedded
controller and it ensures that the registers (in particular CCI) are
synced back to the opregion on notifications. While there is an ACPI call
that syncs the actual registers to the opregion there is rarely a need to
do this and on some ACPI implementations it actually breaks in various
interesting ways.
The only reason to force a sync from the embedded controller is to poll
CCI while notifications are disabled. Only the ucsi core knows if this
is the case and guessing based on the current command is suboptimal, i.e.
leading to the following spurious assertion splat:
WARNING: CPU: 3 PID: 76 at drivers/usb/typec/ucsi/ucsi.c:1388 ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
CPU: 3 UID: 0 PID: 76 Comm: kworker/3:0 Not tainted 6.12.11-200.fc41.x86_64 #1
Hardware name: LENOVO 21D0/LNVNB161216, BIOS J6CN45WW 03/17/2023
Workqueue: events_long ucsi_init_work [typec_ucsi]
RIP: 0010:ucsi_reset_ppm+0x1b4/0x1c0 [typec_ucsi]
Call Trace:
<TASK>
ucsi_init_work+0x3c/0xac0 [typec_ucsi]
process_one_work+0x179/0x330
worker_thread+0x252/0x390
kthread+0xd2/0x100
ret_from_fork+0x34/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
Thus introduce a ->poll_cci() method that works like ->read_cci() with an
additional forced sync and document that this should be used when polling
with notifications disabled. For all other backends that presumably don't
have this issue use the same implementation for both methods.
Fixes: fa48d7e816 ("usb: typec: ucsi: Do not call ACPI _DSM method for UCSI read operations")
Cc: stable <stable@kernel.org>
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Tested-by: Fedor Pchelkin <boddah8794@gmail.com>
Signed-off-by: Fedor Pchelkin <boddah8794@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250217105442.113486-2-boddah8794@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfc1b168a8 upstream.
The userprog infrastructure links objects files through $(CC).
Either explicitly by manually calling $(CC) on multiple object files or
implicitly by directly compiling a source file to an executable.
The documentation at Documentation/kbuild/llvm.rst indicates that ld.lld
would be used for linking if LLVM=1 is specified.
However clang instead will use either a globally installed cross linker
from $PATH called ${target}-ld or fall back to the system linker, which
probably does not support crosslinking.
For the normal kernel build this is not an issue because the linker is
always executed directly, without the compiler being involved.
Explicitly pass --ld-path to clang so $(LD) is respected.
As clang 13.0.1 is required to build the kernel, this option is available.
Fixes: 7f3a59db27 ("kbuild: add infrastructure to build userspace programs")
Cc: stable@vger.kernel.org # needs wrapping in $(cc-option) for < 6.9
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e812e9355 upstream.
If the USB configuration is not valid, then avoid checking for
bmAttributes to prevent null pointer deference.
Cc: stable <stable@kernel.org>
Fixes: 40e89ff575 ("usb: gadget: Set self-powered based on MaxPower and bmAttributes")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250224085604.417327-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c783e1258f upstream.
cdev->config might be NULL, so check it before dereferencing.
CC: stable <stable@kernel.org>
Fixes: 40e89ff575 ("usb: gadget: Set self-powered based on MaxPower and bmAttributes")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20250220120314.3614330-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40e89ff575 upstream.
Currently the USB gadget will be set as bus-powered based solely
on whether its bMaxPower is greater than 100mA, but this may miss
devices that may legitimately draw less than 100mA but still want
to report as bus-powered. Similarly during suspend & resume, USB
gadget is incorrectly marked as bus/self powered without checking
the bmAttributes field. Fix these by configuring the USB gadget
as self or bus powered based on bmAttributes, and explicitly set
it as bus-powered if it draws more than 100mA.
Cc: stable <stable@kernel.org>
Fixes: 5e5caf4fa8 ("usb: gadget: composite: Inform controller driver of self-powered")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250217120328.2446639-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6b82dafd1 upstream.
During probe, the TCPC alert interrupts are getting masked to
avoid unwanted interrupts during chip setup: this is ok to do
but there is no unmasking happening at any later time, which
means that the chip will not raise any interrupt, essentially
making it not functional as, while internally it does perform
all of the intended functions, it won't signal anything to the
outside.
Unmask the alert interrupts to fix functionality.
Fixes: ce08eaeb63 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@kernel.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20250219114700.41700-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf4f9ae1cb upstream.
It is observed that on some systems an initial PPM reset during the boot
phase can trigger a timeout:
[ 6.482546] ucsi_acpi USBC000:00: failed to reset PPM!
[ 6.482551] ucsi_acpi USBC000:00: error -ETIMEDOUT: PPM init failed
Still, increasing the timeout value, albeit being the most straightforward
solution, eliminates the problem: the initial PPM reset may take up to
~8000-10000ms on some Lenovo laptops. When it is reset after the above
period of time (or even if ucsi_reset_ppm() is not called overall), UCSI
works as expected.
Moreover, if the ucsi_acpi module is loaded/unloaded manually after the
system has booted, reading the CCI values and resetting the PPM works
perfectly, without any timeout. Thus it's only a boot-time issue.
The reason for this behavior is not clear but it may be the consequence
of some tricks that the firmware performs or be an actual firmware bug.
As a workaround, increase the timeout to avoid failing the UCSI
initialization prematurely.
Fixes: b1b59e1607 ("usb: typec: ucsi: Increase command completion timeout value")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <boddah8794@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250217105442.113486-3-boddah8794@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc5bfc4e16 upstream.
After phy initialization, some phy operations can only be executed while
in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking
phy ops.
Previously the SUSPENDENABLE bits are only set after the controller
initialization, which may not happen right away if there's no gadget
driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits
only when there's mode switching (change in GCTL.PRTCAPDIR).
Fixes: 6d73572206 ("usb: dwc3: core: Prevent phy suspend during init")
Cc: stable <stable@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/633aef0afee7d56d2316f7cc3e1b2a6d518a8cc9.1738280911.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c90aad3698 upstream.
Syzbot once again identified a flaw in usb endpoint checking, see [1].
This time the issue stems from a commit authored by me (2eabb655a9
("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")).
While using usb_find_common_endpoints() may usually be enough to
discard devices with wrong endpoints, in this case one needs more
than just finding and identifying the sufficient number of endpoints
of correct types - one needs to check the endpoint's address as well.
Since cxacru_bind() fills URBs with CXACRU_EP_CMD address in mind,
switch the endpoint verification approach to usb_check_XXX_endpoints()
instead to fix incomplete ep testing.
[1] Syzbot report:
usb 5-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 1378 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
RIP: 0010:usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503
...
Call Trace:
<TASK>
cxacru_cm+0x3c8/0xe50 drivers/usb/atm/cxacru.c:649
cxacru_card_status drivers/usb/atm/cxacru.c:760 [inline]
cxacru_bind+0xcf9/0x1150 drivers/usb/atm/cxacru.c:1223
usbatm_usb_probe+0x314/0x1d30 drivers/usb/atm/usbatm.c:1058
cxacru_usb_probe+0x184/0x220 drivers/usb/atm/cxacru.c:1377
usb_probe_interface+0x641/0xbb0 drivers/usb/core/driver.c:396
really_probe+0x2b9/0xad0 drivers/base/dd.c:658
__driver_probe_device+0x1a2/0x390 drivers/base/dd.c:800
driver_probe_device+0x50/0x430 drivers/base/dd.c:830
...
Reported-and-tested-by: syzbot+ccbbc229a024fa3e13b5@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ccbbc229a024fa3e13b5
Fixes: 2eabb655a9 ("usb: atm: cxacru: fix endpoint checking in cxacru_bind()")
Cc: stable@kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20250213122259.730772-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17c2c87c37 upstream.
Currently while UDC suspends, u_ether attempts to remote wakeup
the host if there are any pending transfers. However, if remote
wakeup fails, the UDC remains suspended but the is_suspend flag
is not set. And since is_suspend flag isn't set, the subsequent
eth_start_xmit() would queue USB requests to suspended UDC.
To fix this, bail out from gether_suspend() only if remote wakeup
operation is successful.
Cc: stable <stable@kernel.org>
Fixes: 0a1af6dfa0 ("usb: gadget: f_ecm: Add suspend/resume and remote wakeup support")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250212100840.3812153-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552ca6b87e upstream.
When performing continuous unbind/bind operations on the USB drivers
available on the Renesas RZ/G2L SoC, a kernel crash with the message
"Unable to handle kernel NULL pointer dereference at virtual address"
may occur. This issue points to the usbhsc_notify_hotplug() function.
Flush the delayed work to avoid its execution when driver resources are
unavailable.
Fixes: bc57381e63 ("usb: renesas_usbhs: use delayed_work instead of work_struct")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b13abcb7dd upstream.
Resources should be released only after all threads that utilize them
have been destroyed.
This commit ensures that resources are not released prematurely by waiting
for the associated workqueue to complete before deallocating them.
Cc: stable <stable@kernel.org>
Fixes: b9aa02ca39 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250305111739.1489003-2-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff712188da upstream.
When used on Huawei hisi platforms, Prolific Mass Storage Card Reader
which the VID:PID is in 067b:2731 might fail to enumerate at boot time
and doesn't work well with LPM enabled, combination quirks:
USB_QUIRK_DELAY_INIT + USB_QUIRK_NO_LPM
fixed the problems.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250304070757.139473-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b66ef84d0 upstream.
The xHC resources allocated for USB devices are not released in correct
order after resuming in case when while suspend device was reconnected.
This issue has been detected during the fallowing scenario:
- connect hub HS to root port
- connect LS/FS device to hub port
- wait for enumeration to finish
- force host to suspend
- reconnect hub attached to root port
- wake host
For this scenario during enumeration of USB LS/FS device the Cadence xHC
reports completion error code for xHC commands because the xHC resources
used for devices has not been properly released.
XHCI specification doesn't mention that device can be reset in any order
so, we should not treat this issue as Cadence xHC controller bug.
Similar as during disconnecting in this case the device resources should
be cleared starting form the last usb device in tree toward the root hub.
To fix this issue usbcore driver should call hcd->driver->reset_device
for all USB devices connected to hub which was reconnected while
suspending.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/PH7PR07MB953841E38C088678ACDCF6EEDDCC2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0c9244093 upstream.
The gpriv->transceiver is retrieved in probe() through usb_get_phy() but
never released. Use devm_usb_get_phy() to handle this scenario.
This issue was identified through code investigation. No issue was found
without this change.
Fixes: b5a2875605 ("usb: renesas_usbhs: Allow an OTG PHY driver to provide VBUS")
Cc: stable <stable@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250225110248.870417-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 487cfd4a8e upstream.
When adding support for USB3-over-USB4 tunnelling detection, a check
for an Intel-specific capability was added. This capability, which
goes by ID 206, is used without any check that we are actually
dealing with an Intel host.
As it turns out, the Cadence XHCI controller *also* exposes an
extended capability numbered 206 (for unknown purposes), but of
course doesn't have the Intel-specific registers that the tunnelling
code is trying to access. Fun follows.
The core of the problems is that the tunnelling code blindly uses
vendor-specific capabilities without any check (the Intel-provided
documentation I have at hand indicates that 192-255 are indeed
vendor-specific).
Restrict the detection code to Intel HW for real, preventing any
further explosion on my (non-Intel) HW.
Cc: stable <stable@kernel.org>
Fixes: 948ce83fbb ("xhci: Add USB4 tunnel detection for USB3 devices on Intel hosts")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250227194529.2288718-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 391b41f983 ]
of_parse_phandle_with_fixed_args() requires its caller to
call into of_node_put() on the node pointer from the output
structure, but such a call is currently missing.
Call into of_node_put() to rectify that.
Fixes: 159f8a0209 ("gpio-rcar: Add DT support")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250305163753.34913-2-fabrizio.castro.jz@renesas.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5da15a9c11 ]
Add missing skb_dst_drop() to drop reference to the old dst before
adding the new dst to the skb.
Fixes: 79ff2fc31e ("ila: Cache a route to translated address")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Link: https://patch.msgid.link/20250305081655.19032-1-justin.iurman@uliege.be
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e7633d7b9 ]
This patch follows commit 92191dd107 ("net: ipv6: fix dst ref loops in
rpl, seg6 and ioam6 lwtunnels") and, on a second thought, the same patch
is also needed for ila (even though the config that triggered the issue
was pathological, but still, we don't want that to happen).
Fixes: 79ff2fc31e ("ila: Cache a route to translated address")
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Link: https://patch.msgid.link/20250304181039.35951-1-justin.iurman@uliege.be
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf7ee25e70 ]
daddr can be NULL if there is no neighbour table entry present,
in that case the tx packet should be dropped.
saddr will usually be set by MCTP core, but check for NULL in case a
packet is transmitted by a different protocol.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Fixes: c8755b29b5 ("mctp i3c: MCTP I3C driver")
Link: https://patch.msgid.link/20250304-mctp-i3c-null-v1-1-4416bbd56540@codeconstruct.com.au
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccc2f5a436 ]
On MMIO devices (e.g. MT7988 or EN7581) unicast traffic received on lanX
port is flooded on all other user ports if the DSA switch is configured
without VLAN support since PORT_MATRIX in PCR regs contains all user
ports. Similar to MDIO devices (e.g. MT7530 and MT7531) fix the issue
defining default VLAN-ID 0 for MT7530 MMIO devices.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20250304-mt7988-flooding-fix-v1-1-905523ae83e9@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 528361c499 ]
The kernel_recvmsg() function returns an int which could be either
negative error codes or the number of bytes received. The problem is
that the condition:
if (ret < sizeof(*icresp)) {
is type promoted to type unsigned long and negative values are treated
as high positive values which is success, when they should be treated as
failure. Handle invalid positive returns separately from negative
error codes to avoid this problem.
Fixes: 578539e096 ("nvme-tcp: fix connect failure on receiving partial ICResp PDU")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b4035ddbf ]
child_cfs_rq_on_list attempts to convert a 'prev' pointer to a cfs_rq.
This 'prev' pointer can originate from struct rq's leaf_cfs_rq_list,
making the conversion invalid and potentially leading to memory
corruption. Depending on the relative positions of leaf_cfs_rq_list and
the task group (tg) pointer within the struct, this can cause a memory
fault or access garbage data.
The issue arises in list_add_leaf_cfs_rq, where both
cfs_rq->leaf_cfs_rq_list and rq->leaf_cfs_rq_list are added to the same
leaf list. Also, rq->tmp_alone_branch can be set to rq->leaf_cfs_rq_list.
This adds a check `if (prev == &rq->leaf_cfs_rq_list)` after the main
conditional in child_cfs_rq_on_list. This ensures that the container_of
operation will convert a correct cfs_rq struct.
This check is sufficient because only cfs_rqs on the same CPU are added
to the list, so verifying the 'prev' pointer against the current rq's list
head is enough.
Fixes a potential memory corruption issue that due to current struct
layout might not be manifesting as a crash but could lead to unpredictable
behavior when the layout changes.
Fixes: fdaba61ef8 ("sched/fair: Ensure that the CFS parent is added after unthrottling")
Signed-off-by: Zecheng Li <zecheng@google.com>
Reviewed-and-tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20250304214031.2882646-1-zecheng@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ac60242b0 ]
The parameters set by the set_params call are only applied to the block
device in the start_dev call. So if a device has already been started, a
subsequently issued set_params on that device will not have the desired
effect, and should return an error. There is an existing check for this
- set_params fails on devices in the LIVE state. But this check is not
sufficient to cover the recovery case. In this case, the device will be
in the QUIESCED or FAIL_IO states, so set_params will succeed. But this
success is misleading, because the parameters will not be applied, since
the device has already been started (by a previous ublk server). The bit
UB_STATE_USED is set on completion of the start_dev; use it to detect
and fail set_params commands which arrive too late to be applied (after
start_dev).
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Fixes: 0aa73170eb ("ublk_drv: add SET_PARAMS/GET_PARAMS control command")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250304-set_params-v1-1-17b5e0887606@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c9231ea64 ]
When I read through the TSO codes, I found out that we probably
miss initializing the tx_flags of last seg when TSO is turned
off, which means at the following points no more timestamp
(for this last one) will be generated. There are three flags
to be handled in this patch:
1. SKBTX_HW_TSTAMP
2. SKBTX_BPF
3. SKBTX_SCHED_TSTAMP
Note that SKBTX_BPF[1] was added in 6.14.0-rc2 by commit
6b98ec7e88 ("bpf: Add BPF_SOCK_OPS_TSTAMP_SCHED_CB callback")
and only belongs to net-next branch material for now. The common
issue of the above three flags can be fixed by this single patch.
This patch initializes the tx_flags to SKBTX_ANY_TSTAMP like what
the UDP GSO does to make the newly segmented last skb inherit the
tx_flags so that requested timestamp will be generated in each
certain layer, or else that last one has zero value of tx_flags
which leads to no timestamp at all.
Fixes: 4ed2d765df ("net-timestamp: TCP timestamping")
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fda94a9919 ]
When generic_write_checks() returns zero, it means that
iov_iter_count() is zero, and there is no work to do.
Simply return success like all other filesystems do, rather than
proceeding down the write path, which today yields an -EFAULT in
generic_perform_write() via the
(fault_in_iov_iter_readable(i, bytes) == bytes) check when bytes
== 0.
Fixes: 11a347fb6c ("exfat: change to get file size from DataLength")
Reported-by: Noah <kernel-org-10@maxgrass.eu>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9da33619e0 ]
bitmap clear loop will take long time in __exfat_free_cluster()
if data size of file/dir enty is invalid.
If cluster bit in bitmap is already clear, stop clearing bitmap go to
out of loop.
Fixes: 31023864e6 ("exfat: add fat entry operations")
Reported-by: Kun Hu <huk23@m.fudan.edu.cn>, Jiaji Qin <jjtan24@m.fudan.edu.cn>
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6697f819a1 ]
This commit fixes the condition for allocating cluster to parent
directory to avoid allocating new cluster to parent directory when
there are just enough empty directory entries at the end of the
parent directory.
Fixes: af02c72d0b ("exfat: convert exfat_find_empty_entry() to use dentry cache")
Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d3e0dfd68 ]
The total size calculated for EPC can overflow u64 given the added up page
for SECS. Further, the total size calculated for shmem can overflow even
when the EPC size stays within limits of u64, given that it adds the extra
space for 128 byte PCMD structures (one for each page).
Address this by pre-evaluating the micro-architectural requirement of
SGX: the address space size must be power of two. This is eventually
checked up by ECREATE but the pre-check has the additional benefit of
making sure that there is some space for additional data.
Fixes: 888d249117 ("x86/sgx: Add SGX_IOC_ENCLAVE_CREATE")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lore.kernel.org/r/20250305050006.43896-1-jarkko@kernel.org
Closes: https://lore.kernel.org/linux-sgx/c87e01a0-e7dd-4749-a348-0980d3444f04@stanley.mountain/
Signed-off-by: Sasha Levin <sashal@kernel.org>
