Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/20240416-pci-rockchip-perst-fix-v1-1-4800b1d4d954@linaro.org
Reported-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Cc: stable@vger.kernel.org # v4.9
PCIe r6.0, sec 6.6.1, states that the host should wait for at least 100
msec from the end of a conventional reset (PERST# is de-asserted) before
sending a configuration request to ensure that the device is able to
respond with a "Request Retry Status" completion.
Add the PCIE_T_RRS_READY_MS macro to define this wait time and modify
rockchip_pcie_host_init_port() to add this 100ms sleep after deasserting
PERST# using the ep_gpio GPIO.
Link: https://lore.kernel.org/linux-pci/20240413004120.1099089-3-dlemoal@kernel.org
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
PCIe CEM r5.1, sec 2.9.2, mandates that the PERST# signal must remain
asserted for at least 100 usec (Tperst-clk) after the PCIe reference clock
becomes stable (if a reference clock is supplied), and for at least 100
msec after the power is stable (Tpvperl, defined by the macro
PCIE_T_PVPERL_MS).
Modify rockchip_pcie_host_init_port() to satisfy these constraints by
adding a sleep period before deasserting PERST# using the ep_gpio GPIO.
Since Tperst-clk is the shorter wait time, add an msleep() call for the
longer PCIE_T_PVPERL_MS milliseconds to handle both timing requirements.
Link: https://lore.kernel.org/linux-pci/20240413004120.1099089-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
From the DWC EP databook 5.96a, section "3.5.7.1.4 General Rules for BAR
Setup (Fixed Mask or Programmable Mask Schemes Only)":
"Any pair (for example BARs 0 and 1) can be configured as one 64-bit BAR,
two 32-bit BARs, or one 32-bit BAR."
"BAR pairs cannot overlap to form a 64-bit BAR. For example, you cannot
combine BARs 1 and 2 to form a 64-bit BAR."
While this limitation does exist in some other PCI endpoint controllers,
e.g. cdns_pcie_ep_set_bar(), the limitation does not appear to be defined
in the PCIe specification itself, thus add an explicit check for this in
dw_pcie_ep_set_bar() (rather than pci_epc_set_bar()).
Link: https://lore.kernel.org/linux-pci/20240528134839.8817-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Now that dw_pcie_ep_linkdown() is available, use it. This also handles the
reinitialization of DWC non-sticky registers in addition to sending the
notification to EPF drivers.
Closes: https://lore.kernel.org/linux-pci/20240528195539.GA458945@bhelgaas
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-5-4395534520dc@linaro.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Now that the generic dw_pcie_ep_linkdown() API is available, use it. This
also handles the reinitialization of DWC non-sticky registers in addition
to sending the notification to EPF drivers.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-9-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify()
directly, so this wrapper provides no benefit to the glue drivers.
Remove it and call pci_epc_init_notify() directly from glue drivers.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
According to [1], msleep should be used for large sleeps, such as the
100-ish ms one in this function. Comply with the guide and use it.
[1] https://docs.kernel.org/timers/timers-howto.html
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240215-topic-pci_sleep-v2-1-79334884546b@linaro.org
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
With commit 5779dd0a7d ("PCI: endpoint: Use notification chain mechanism
to notify EPC events to EPF") the linkup callback has been removed and
replaced by EPC event notifications.
With commit 256ae47520 ("PCI: endpoint: Add pci_epf_ops to expose
function-specific attrs") a new (optional) add_cfs callback was added.
Update documentation accordingly.
Link: https://lore.kernel.org/linux-pci/20240418084924.1724703-1-alexander.stein@ew.tq-group.com
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
These two functions are defined in the pci_endpoint_test.c file, but not
called elsewhere, so delete these unused functions.
This fixes the following warning:
drivers/misc/pci_endpoint_test.c:144:19: warning: unused function 'pci_endpoint_test_bar_readl'.
drivers/misc/pci_endpoint_test.c:150:20: warning: unused function 'pci_endpoint_test_bar_writel'.
No functional changes intended.
[kwilczynski: commit log]
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=9064
Link: https://lore.kernel.org/linux-pci/20240704023227.87039-1-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a comment suggesting that if the endpoint controller Vendor and Device
ID are programmable, an existing entry might be usable for testing without
having to add an entry to pci_endpoint_test_tbl[].
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-6-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
dma_set_mask_and_coherent() should never fail when the mask is >= 32bit,
unless the architecture has no DMA support. So no need to check for the
error and also no need to set dma_set_mask_and_coherent(32) as a fallback.
Even if dma_set_mask_and_coherent(48) fails due to the lack of DMA support
(theoretically), then dma_set_mask_and_coherent(32) will also fail for the
same reason. So the fallback doesn't make sense.
Simplify the code by setting the streaming and coherent DMA mask to 48
bits.
Link: https://lore.kernel.org/linux-pci/20240502195903.3191049-1-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
The current code uses writel()/readl(), which has an implicit memory
barrier for every single readl()/writel().
Additionally, reading 4 bytes at a time over the PCI bus is not really
optimal, considering that this code is running in an ioctl handler.
Use memcpy_toio()/memcpy_fromio() for BAR tests.
Before patch with a 4MB BAR:
$ time /usr/bin/pcitest -b 1
BAR1: OKAY
real 0m 1.56s
After patch with a 4MB BAR:
$ time /usr/bin/pcitest -b 1
BAR1: OKAY
real 0m 0.54s
Link: https://lore.kernel.org/linux-pci/20240322164139.678228-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Rockchip rk3588 requires 64KB alignment for BARs.
While there is an existing device_id:vendor_id in the driver with 64KB
alignment, that device_id:vendor_id is am654, which uses BAR2 instead of
BAR0 as the test_reg_bar, and also has special is_am654_pci_dev() checks
in the driver to disallow BAR0. In order to allow testing all BARs, add a
new rk3588 entry in the driver.
We intentionally do not add the vendor id to pci_ids.h, since the policy
for that file is that the vendor id has to be used by multiple drivers.
Hopefully, this new entry will be short-lived, as there is a series on the
mailing list which intends to move the address alignment restrictions from
this driver to the endpoint side.
Add a new entry for rk3588 in order to allow us to test all BARs.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-11-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There are two issues related to epf_ntb_epc_cleanup():
1) It should call epf_ntb_config_sspad_bar_clear()
2) The epf_ntb_bind() function should call epf_ntb_epc_cleanup()
to cleanup.
I also changed the ordering a bit. Unwinding should be done in the
mirror order from how they are allocated.
Fixes: e35f56bb03 ("PCI: endpoint: Support NTB transfer between RC and EP")
Link: https://lore.kernel.org/linux-pci/aaffbe8d-7094-4083-8146-185f4a84e8a1@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Smatch complains about inconsistent NULL checking in vpci_scan_bus():
drivers/pci/endpoint/functions/pci-epf-vntb.c:1024 vpci_scan_bus() error: we previously assumed 'vpci_bus' could be null (see line 1021)
Instead of printing an error message and then crashing we should return
an error code and clean up.
Also the NULL check is reversed so it prints an error for success
instead of failure.
Fixes: e35f56bb03 ("PCI: endpoint: Support NTB transfer between RC and EP")
Link: https://lore.kernel.org/linux-pci/68e0f6a4-fd57-45d0-945b-0876f2c8cb86@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Now that the driver core allows for struct class to be in read-only
memory, we should make all 'class' structures declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at runtime.
Link: https://lore.kernel.org/linux-pci/2024061011-citable-herbicide-1095@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
As like the 'epc_init' event, that is used to signal the EPF drivers about
the EPC initialization, let's introduce 'epc_deinit' event that is used to
signal EPC deinitialization.
The EPC deinitialization applies only when any sort of fundamental reset
is supported by the endpoint controller as per the PCIe spec.
Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1.
Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support
PERST# as the fundamental reset. So the 'deinit' event will be notified to
the EPF drivers when PERST# assert happens in the above mentioned EPC
drivers.
The EPF drivers, on receiving the event through the epc_deinit() callback
should reset the EPF state machine and also cleanup any configuration that
got affected by the fundamental reset like BAR, DMA etc...
This change also warrants skipping the cleanups in unbind() if already done
in epc_deinit().
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
When the event happens, the EPC driver capable of detecting it may pass the
notification to the EPF driver through link_down() callback in 'struct
pci_epc_event_ops'.
While the PCIe spec has not defined the actual behavior of the endpoint
when the Link Down event happens, we may assume that at least the ongoing
transactions need to be stopped as the link won't be active, so
cancel the command handler work in the callback implementation
pci_epf_test_link_down(). The work will be started again in
pci_epf_test_link_up() once the link comes back again.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-10-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
To maintain uniformity across EPF drivers, move DMA initialization to EPC
init callback. This will also allow us to deinit DMA during PERST# assert
in the further commits.
For EPC drivers without PERST#, DMA deinit will only happen during driver
unbind.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-6-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Move the pci_epc_clear_bar() and pci_epf_free_space() code to respective
helper functions. This allows reusing the helpers in future commits.
This also requires moving the pci_epf_test_unbind() definition below
pci_epf_test_bind() to avoid forward declaration of the above helpers.
No functional change.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-5-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
BME which stands for 'Bus Master Enable' is not defined in the PCIe base
spec even though it is commonly referred in many places (vendor docs). To
align with the spec, rename it to its expansion 'Bus Master Enable'.
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-3-22832d0d456f@linaro.org
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-4-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: squash removal of irrelevant 'Link is enabled']
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
core_init() callback is used to notify the EPC initialization event to the
EPF drivers. The 'core' prefix was used indicate that the controller IP
core has completed initialization. But it serves no purpose as the EPF
driver will only care about the EPC initialization as a whole and there is
no real benefit to distinguish the IP core part.
Rename the core_init() callback in 'struct pci_epc_event_ops' to epc_init()
to make it more clear.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-2-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Instead of using a local variable to cache the 'msix_capable' flag, use it
directly to simplify the code.
Suggested-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240418-pci-epf-test-fix-v2-2-eacd54831444@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Instead of getting the epc_features from pci_epc_get_features() API, use
the cached pci_epf_test::epc_features value to avoid the NULL check. Since
the NULL check is already performed in pci_epf_test_bind(), having one more
check in pci_epf_test_core_init() is redundant and it is not possible to
hit the NULL pointer dereference.
Also with commit a01e7214be ("PCI: endpoint: Remove "core_init_notifier"
flag"), 'epc_features' got dereferenced without the NULL check, leading to
the following false positive Smatch warning:
drivers/pci/endpoint/functions/pci-epf-test.c:784 pci_epf_test_core_init() error: we previously assumed 'epc_features' could be null (see line 747)
Thus, remove the redundant NULL check and also use the epc_features::
{msix_capable/msi_capable} flags directly to avoid local variables.
[kwilczynski: commit log]
Fixes: 5e50ee27d4 ("PCI: pci-epf-test: Add support to defer core initialization")
Closes: https://lore.kernel.org/linux-pci/024b5826-7180-4076-ae08-57d2584cca3f@moroto.mountain
Link: https://lore.kernel.org/linux-pci/20240418-pci-epf-test-fix-v2-1-eacd54831444@linaro.org
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
In "struct pci_epf_group", the 'type_group' field is unused.
This was added, but already unused, by commit 70b3740f2c ("PCI: endpoint:
Automatically create a function specific attributes group").
Thus, remove it.
Found with cppcheck, unusedStructMember.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/6507d44b6c60a19af35a605e2d58050be8872ab6.1712341008.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 24e44cc22a ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.
The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle."
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCZlMhdgAKCRCyPKLppCJ+
JzCNAPwM7gQLjeoCdkn9KDl1fj1R7/jBE/TsVqP9s1htc9vJEgD/UgLDkpdzlxBC
HbndVTOrnvyV9ySA28654ODHpQxmXwM=
=WJwT
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tool fix from Arnaldo Carvalho de Melo:
"Revert a patch causing a regression.
This made a simple 'perf record -e cycles:pp make -j199' stop working
on the Ampere ARM64 system Linus uses to test ARM64 kernels".
* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
This reverts commit 617824a7f0.
This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.
The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Cc: Ethan Adams <j.ethan.adams@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Tycho Andersen <tycho@tycho.pizza>
Cc: Yang Jihong <yangjihong@bytedance.com>
Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com
Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----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=p0nS
-----END PGP SIGNATURE-----
Merge tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- two important netfs integration fixes - including for a data
corruption and also fixes for multiple xfstests
- reenable swap support over SMB3
* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix missing set of remote_i_size
cifs: Fix smb3_insert_range() to move the zero_point
cifs: update internal version number
smb3: reenable swapfiles over SMB3 mounts
A few nilfs2 fixes, the remainder are for MM: a couple of selftests fixes,
various singletons fixing various issues in various parts.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZlIOUgAKCRDdBJ7gKXxA
jrYnAP9UeOw8YchTIsjEllmAbTMAqWGI+54CU/qD78jdIHoVWAEAmp0QqgFW3r2p
jze4jBkh3lGQjykTjkUskaR71h9AZww=
=AHeV
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
- Fix x86 IRQ vector leak caused by a CPU offlining race
- Fix build failure in the riscv-imsic irqchip driver
caused by an API-change semantic conflict
- Fix use-after-free in irq_find_at_or_after()
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vxJh
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
- Fix x86 IRQ vector leak caused by a CPU offlining race
- Fix build failure in the riscv-imsic irqchip driver
caused by an API-change semantic conflict
- Fix use-after-free in irq_find_at_or_after()
* tag 'irq-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after()
genirq/cpuhotplug, x86/vector: Prevent vector leak during CPU offline
irqchip/riscv-imsic: Fixup riscv_ipi_set_virq_range() conflict
- Fix regressions of the new x86 CPU VFM (vendor/family/model)
enumeration/matching code
- Fix crash kernel detection on buggy firmware with
non-compliant ACPI MADT tables
- Address Kconfig warning
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=nIcm
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix regressions of the new x86 CPU VFM (vendor/family/model)
enumeration/matching code
- Fix crash kernel detection on buggy firmware with
non-compliant ACPI MADT tables
- Address Kconfig warning
* tag 'x86-urgent-2024-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix x86_match_cpu() to match just X86_VENDOR_INTEL
crypto: x86/aes-xts - switch to new Intel CPU model defines
x86/topology: Handle bogus ACPI tables correctly
x86/kconfig: Select ARCH_WANT_FRAME_POINTERS again when UNWINDER_FRAME_POINTER=y
These changes are mostly updates for deprecated interfaces,
platform.remove and converting from a tasklet to a BH workqueue. Also
use HAS_IOPORT for disabling inb()/outb().
-corey
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE/Q1c5nzg9ZpmiCaGYfOMkJGb/4EFAmZCYRMACgkQYfOMkJGb
/4FqGBAAq2KsgdpCSquJMl8uvlxXzxpZJsUpZBMPeZyI9kJUPimNVvkd0iz2zx4C
0yU9UxUcIViU1MuL8KyRhC/vpoDg3cZLspvkntWoU/qGcfQMsnxgbuogBKXTjRWt
cOi/rFSBFXMv0gQ+aNWlFHVZdzQQ1vuiIIZNvIBNjvfaJargYXlUX91ejY/1DZHc
Eeq0N7AiswPD0q1KZjJ5W2YYwqiNRubUbA2eq2mFvTbODi0JPgyNYI0qikMTFGM/
L2vFRylqzMr63uFh5j+Dc1oJqdc+XtqOMIDd+34h+43td7XbBW+magdNBBLzMuYt
HmrvBvlNH1zjXVEpAkqrOFnBYCisynKXvco7rhyTX1MaLuBo+pFNBzFlOw9s6Ydv
+4VIBMcyz7ZVcOQgrZX5d5ly5Oh5wjAnIN3IPeDczaieMlfhk+e/MJBwDNT/7frD
j7bnQ0tuzMvMhtZ/YfdzOZR/08cBMPRB2EJBGIQrTZeKJPcTLW73IkbQqQ6/8San
dOgOqOGx/mAegf0vRp8ZPlyYAlSZ5l5cANRyWZjG8+EkajFB26iJmXY0jyf1yZ+I
Vzb79YqmtB2eu/fFuJ5suF4UkvI8RLFEJxnPRvBe+420rFHs4yHL5TzyzIOACL29
OGAoatvC7qBWNYFWh8P3jFyxScVBC4lV1FYWwoCwOFevMz9kAXw=
=IPex
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.10-1' of https://github.com/cminyard/linux-ipmi
Pull ipmi updates from Corey Minyard:
"Mostly updates for deprecated interfaces, platform.remove and
converting from a tasklet to a BH workqueue.
Also use HAS_IOPORT for disabling inb()/outb()"
* tag 'for-linus-6.10-1' of https://github.com/cminyard/linux-ipmi:
ipmi: kcs_bmc_npcm7xx: Convert to platform remove callback returning void
ipmi: kcs_bmc_aspeed: Convert to platform remove callback returning void
ipmi: ipmi_ssif: Convert to platform remove callback returning void
ipmi: ipmi_si_platform: Convert to platform remove callback returning void
ipmi: ipmi_powernv: Convert to platform remove callback returning void
ipmi: bt-bmc: Convert to platform remove callback returning void
char: ipmi: handle HAS_IOPORT dependencies
ipmi: Convert from tasklet to BH workqueue
checks based on MDS auth caps which were recently made available to
clients. This is needed to prevent scenarios where the MDS quietly
discards updates that a UID-restricted client previously (wrongfully)
acked to the user. Other than that, just a documentation fixup.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmZRsm0THGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi6++B/4o7j4CNzjJcBw9UgxEUugwJYBe2Ht3
vSTUkHD9NILVgrYSHNhgkCdvU8ckv8Sd+7W/Kb0BC/GRyQd57F7zoM6mvR1WMozt
lLbYU/kdVI+TcIY2bhupMma5f+nWv6vIBTzca78UhogEBuIEYHAG3BnNaT/AEqF+
yZ3uQEVQ2bHmwbPn3A5dibYxOR8zLyhmaq/RUvqpiiYcSkEfZ6QqKiMlZkcVD7F8
c+NfjwXXGNTXDhfIbG4VndQi7xLXk3GI5E8xvdo2ALwumfp2KdVlMEYT8SHggSPS
A8bWq+d5o7uVV6WviNK63XcGRpadCSSSL310vR78K+tNIIq5dnI81IsU
=6c1e
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A series from Xiubo that adds support for additional access checks
based on MDS auth caps which were recently made available to clients.
This is needed to prevent scenarios where the MDS quietly discards
updates that a UID-restricted client previously (wrongfully) acked to
the user.
Other than that, just a documentation fixup"
* tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client:
doc: ceph: update userspace command to get CephFS metadata
ceph: add CEPHFS_FEATURE_MDS_AUTH_CAPS_CHECK feature bit
ceph: check the cephx mds auth access for async dirop
ceph: check the cephx mds auth access for open
ceph: check the cephx mds auth access for setattr
ceph: add ceph_mds_check_access() helper
ceph: save cap_auths in MDS client when session is opened
-----BEGIN PGP SIGNATURE-----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=IALr
-----END PGP SIGNATURE-----
Merge tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 updates from Konstantin Komarov:
"Fixes:
- reusing of the file index (could cause the file to be trimmed)
- infinite dir enumeration
- taking DOS names into account during link counting
- le32_to_cpu conversion, 32 bit overflow, NULL check
- some code was refactored
Changes:
- removed max link count info display during driver init
Remove:
- atomic_open has been removed for lack of use"
* tag 'ntfs3_for_6.10' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: Break dir enumeration if directory contents error
fs/ntfs3: Fix case when index is reused during tree transformation
fs/ntfs3: Mark volume as dirty if xattr is broken
fs/ntfs3: Always make file nonresident on fallocate call
fs/ntfs3: Redesign ntfs_create_inode to return error code instead of inode
fs/ntfs3: Use variable length array instead of fixed size
fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow
fs/ntfs3: Check 'folio' pointer for NULL
fs/ntfs3: Missed le32_to_cpu conversion
fs/ntfs3: Remove max link count info display during driver init
fs/ntfs3: Taking DOS names into account during link counting
fs/ntfs3: remove atomic_open
fs/ntfs3: use kcalloc() instead of kzalloc()
-----BEGIN PGP SIGNATURE-----
iQGzBAABCgAdFiEE6fsu8pdIjtWE/DpLiiy9cAdyT1EFAmZRUpIACgkQiiy9cAdy
T1FIeQwAhZbsWGN/zwAP2tLbfrCpX0kFXfWIesOLZW53+6vnEXHUDHP7iN3Au1OA
EDyeH4Sh1YcgP80mIzR+9iN3jY1FDY9G+dxfY5XdE4tSPQIIORko5B1GiumDHAZU
NJivgLawK8OOvO01RgR5V/jyElZf0W+P2gaC/RWx4W7rGvzs9J+2uZnciTdmAGH0
gF7zqgzM3lp7BTGD0zuaGU32W/4gcrAxVdqTkqR+i4n5/Jr9eJJWbHcxsKSun1HY
75/BEvEJAHwQ4kMkR329pJwySyp3Zgzs7m4HAZwHKOUDzYLAnR7w2WNVNdY88T3/
b0dQxY4V1cONaxiSN9MycoMMv59/P7VVnhvZIMhd5e7hBd4AgxUFj2c11okssGOf
9P5BpTPGlAFYNAYR2p0uv0i3Xh6WF1Kor2SCdoIh2OkyCmhtertw+AqkqkOCiFGM
ttwardj7+KuCKaKG7wl5UDfwnol04v6d4xoeh76jQx14euBpEfpED+ENS5fbdLu8
F5I++L3M
=JStz
-----END PGP SIGNATURE-----
Merge tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
"Two ksmbd server fixes, both for stable"
* tag '6.10-rc-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: ignore trailing slashes in share paths
ksmbd: avoid to send duplicate oplock break notifications
New driver:
- Epson RX8111
Drivers:
- Many Device Tree bindings conversions to dtschema
- pcf8563: wakeup-source support
-----BEGIN PGP SIGNATURE-----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=Kclo
-----END PGP SIGNATURE-----
Merge tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is one new driver and then most of the changes are the device
tree bindings conversions to yaml.
New driver:
- Epson RX8111
Drivers:
- Many Device Tree bindings conversions to dtschema
- pcf8563: wakeup-source support"
* tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
pcf8563: add wakeup-source support
rtc: rx8111: handle VLOW flag
rtc: rx8111: demote warnings to debug level
rtc: rx6110: Constify struct regmap_config
dt-bindings: rtc: convert trivial devices into dtschema
dt-bindings: rtc: stmp3xxx-rtc: convert to dtschema
dt-bindings: rtc: pxa-rtc: convert to dtschema
rtc: Add driver for Epson RX8111
dt-bindings: rtc: Add Epson RX8111
rtc: mcp795: drop unneeded MODULE_ALIAS
rtc: nuvoton: Modify part number value
rtc: test: Split rtc unit test into slow and normal speed test
dt-bindings: rtc: nxp,lpc1788-rtc: convert to dtschema
dt-bindings: rtc: digicolor-rtc: move to trivial-rtc
dt-bindings: rtc: alphascale,asm9260-rtc: convert to dtschema
dt-bindings: rtc: armada-380-rtc: convert to dtschema
rtc: cros-ec: provide ID table for avoiding fallback match
Core:
- Allow device driver to trigger controller runtime PM
Drivers:
- dw: hot-join support
- svc: better IBI handling
-----BEGIN PGP SIGNATURE-----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=EmUy
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"Runtime PM (power management) is improved and hot-join support has
been added to the dw controller driver.
Core:
- Allow device driver to trigger controller runtime PM
Drivers:
- dw: hot-join support
- svc: better IBI handling"
* tag 'i3c/for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: dw: Add hot-join support.
i3c: master: Enable runtime PM for master controller
i3c: master: svc: fix invalidate IBI type and miss call client IBI handler
i3c: master: svc: change ENXIO to EAGAIN when IBI occurs during start frame
i3c: Add comment for -EAGAIN in i3c_device_do_priv_xfers()
- Fixes for -Wmissing-prototypes warnings and further cleanup
- Remove callback returning void from rtc and virtio drivers
- Fix bash location
-----BEGIN PGP SIGNATURE-----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=umlG
-----END PGP SIGNATURE-----
Merge tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux
Pull UML updates from Richard Weinberger:
- Fixes for -Wmissing-prototypes warnings and further cleanup
- Remove callback returning void from rtc and virtio drivers
- Fix bash location
* tag 'uml-for-linus-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux: (26 commits)
um: virtio_uml: Convert to platform remove callback returning void
um: rtc: Convert to platform remove callback returning void
um: Remove unused do_get_thread_area function
um: Fix -Wmissing-prototypes warnings for __vdso_*
um: Add an internal header shared among the user code
um: Fix the declaration of kasan_map_memory
um: Fix the -Wmissing-prototypes warning for get_thread_reg
um: Fix the -Wmissing-prototypes warning for __switch_mm
um: Fix -Wmissing-prototypes warnings for (rt_)sigreturn
um: Stop tracking host PID in cpu_tasks
um: process: remove unused 'n' variable
um: vector: remove unused len variable/calculation
um: vector: fix bpfflash parameter evaluation
um: slirp: remove set but unused variable 'pid'
um: signal: move pid variable where needed
um: Makefile: use bash from the environment
um: Add winch to winch_handlers before registering winch IRQ
um: Fix -Wmissing-prototypes warnings for __warp_* and foo
um: Fix -Wmissing-prototypes warnings for text_poke*
um: Move declarations to proper headers
...
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe work.
-----BEGIN PGP SIGNATURE-----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=pexB
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Some fixes for the end of the merge window, mostly amdgpu and panthor,
with one nouveau uAPI change that fixes a bad decision we made a few
months back.
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe
work"
* tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel:
drm/amdgpu/atomfirmware: add intergrated info v2.3 table
drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2
drm/amdkfd: Let VRAM allocations go to GTT domain on small APUs
drm/amdkfd: handle duplicate BOs in reserve_bo_and_cond_vms
drm/bridge: adv7511: Attach next bridge without creating connector
drm/buddy: Fix the warn on's during force merge
drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations
drm/panthor: Call panthor_sched_post_reset() even if the reset failed
drm/panthor: Reset the FW VM to NULL on unplug
drm/panthor: Keep a ref to the VM at the panthor_kernel_bo level
drm/panthor: Force an immediate reset on unrecoverable faults
drm/panthor: Document drm_panthor_tiler_heap_destroy::handle validity constraints
drm/panthor: Fix an off-by-one in the heap context retrieval logic
drm/panthor: Relax the constraints on the tiler chunk size
drm/panthor: Make sure the tiler initial/max chunks are consistent
drm/panthor: Fix tiler OOM handling to allow incremental rendering
drm: xlnx: zynqmp_dpsub: Fix compilation error
drm: xlnx: zynqmp_dpsub: Fix few function comments
