Commit graph

361,091 commits

Author SHA1 Message Date
Joachim Eastwood
0668744f79 net/at91_ether: add pdata flag for reverse Eth addr
This will allow us to remove the last mach include from at91_ether
and also make it easier to share address setup with macb.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:40:10 -04:00
Joachim Eastwood
f4a15e1b29 net/at91_ether: select MACB in Kconfig
Now that HAVE_NET_MACB is gone let's just select MACB to
satisfy the dependecies in at91_ether.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:40:09 -04:00
Joachim Eastwood
84222e20c1 net/cadence: get rid of HAVE_NET_MACB
macb is a platform driver and there is nothing that prevents
this driver from being built on non-ARM/AVR32 platforms.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:40:09 -04:00
Joachim Eastwood
95ebcea69c net/macb: fix truncate warnings
When building macb on x86_64 the following warnings show up:
  drivers/net/ethernet/cadence/macb.c: In function macb_interrupt:
  drivers/net/ethernet/cadence/macb.c:556:4: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c: In function macb_reset_hw:
  drivers/net/ethernet/cadence/macb.c:792:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c:793:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c:796:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]

Use -1 insted of ~0UL, as done in other places in the driver,
to silence these warnings.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:40:09 -04:00
Nicolas Dichtel
51ebd31815 ipv6: add support of equal cost multipath (ECMP)
Each nexthop is added like a single route in the routing table. All routes
that have the same metric/weight and destination but not the same gateway
are considering as ECMP routes. They are linked together, through a list called
rt6i_siblings.

ECMP routes can be added in one shot, with RTA_MULTIPATH attribute or one after
the other (in both case, the flag NLM_F_EXCL should not be set).

The patch is based on a previous work from
Luc Saillard <luc.saillard@6wind.com>.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:38:32 -04:00
Jean Delvare
0b63bf1fe6 MAINTAINERS: NETWORKING DRIVERS matches too much
File pattern include/linux/*device.h matches too much, including
completely unrelated files. Replace it with an explicit list of
network device-related header files.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:33:11 -04:00
Veaceslav Falico
a35279f002 pch_gbe: don't reset MAC_RX on FIFO overflow
Currently, when FIFO_ERR happens, we stop the dma, wait for it to become
idle and then reset the whole MAC_RX logic (and after that we must re-set
multicast addresses and also re-enable MAC_RX when we're finally ready to
accept new packets). This leads to CRC errors on high number of incoming
packets and is not needed according to the datasheet.

This patch fixes it by the following steps:

1) remove this reset in pch_gbe_stop_receive(), which causes some functions
to not be used anywhere
2) remove already unused functions pch_gbe_wait_clr_bit_irq() and
pch_gbe_mac_reset_rx() to correctly build
3) move pch_gbe_enable_mac_rx() out of pch_gbe_start_receive() to
pch_gbe_up() where it's only needed after we've removed the MAC_RX reset
4) rename pch_gbe_start/stop_receive() to pch_gbe_enable/disable_dma_rx()
to more precisely reflect what the functions are now doing.

After these changes we already don't see the CRC errors and gain some
increase in RX processing speed.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:31:15 -04:00
Veaceslav Falico
9c0314e111 pch_gbe: don't re-set RX_FIFO_ERR flag in napi_poll
If we were in RX_FIFO_ERR state and entered pch_gbe_napi_poll(), we'll
anyway clean some rx space and thus can continue to receive more packets.
Currently, we re-set the RX_FIFO_ERR in situations when we've exhausted our
budget for RX cleaning or cleaned some TX packets. Removing it gives us
+20%-40% speed increase and a lot less of RX_FIFO_ERRors reported.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:31:15 -04:00
Veaceslav Falico
e408a9ff3c pch_gbe: create functions for MAC_RX {en,dis}able
Move MAC_RX-related bits into separate functions.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-23 02:31:15 -04:00
Linus Torvalds
2d1f4c8e09 Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
 "Fixes for intel and nouveau mainly.

   - intel: disable HSW by default, sdvo fixes, link train regression
     fix
   - nouveau: acpi rom loading regression fix, with a few other fixes
     from the rework
   -core: just other minor fixes and race fixes for ttm."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (24 commits)
  drm/ttm: Fix a theoretical race in ttm_bo_cleanup_refs()
  drm/ttm: Fix a theoretical race
  drm: platform: Don't initialize driver-private data
  drm/debugfs: remove redundant info from gem_names
  drm: fb: cma: Fail gracefully on allocation failure
  drm: fb: cma: Fix typo in debug message
  drm/nouveau/clock: fix missing pll type/addr when matching default entry
  drm/nouveau/fb: fix reporting of memory type on GF8+ IGPs
  drm/nv41/vm: don't init hw pciegart on boards with agp bridge
  drm/nouveau/bios: fetch full 4KiB block to determine ACPI ROM image size
  drm/nouveau: validate vbios size
  drm/nouveau: warn when trying to free mm which is still in use
  drm/nouveau: fix nouveau_mm/nouveau_mm_node leak
  drm/nouveau/bios: improve error handling when reading the vbios from ACPI
  drm/nouveau: handle same-fb page flips
  drm/i915: Initialize obj->pages before use by i915_gem_object_do_bit17_swizzle()
  drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
  drm/i915: Insert i915_preliminary_hw_support variable.
  drm/i915: shut up spurious WARN in the gtt fault handler
  Revert "drm/i915: Try harder to complete DP training pattern 1"
  ...
2012-10-23 08:51:07 +03:00
Linus Torvalds
d888af9654 Bug fix: Fix FITRIM argument handling
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iQIcBAABAgAGBQJQhZDSAAoJEDaohF61QIxkwgkP/0j/ygUXo50k7EkdwFsC0mHw
 lQ5iirP7oUJ1p1v2PeaBqBulql5yseqTj6keLTTrYSBG/Ocp8qir9z0pyqWjN112
 DU8o/CPSVXnAj64d7Nu/YZBGdUHWQu+1Wex+nDyh2QXdJx94G3SoE3ZZ86BiXJ01
 1rVvHB+FuyzbKFCEk8hslKyJ8WHv1flu+9ulxQXDATrxJxqqTvBkRdT21h3Ds+d8
 HQhxj2RHT7yVHWvyQumTNLLVWOtuT+Svd3Mglzl4bbfAQ49THJFHaxGp1ufGZlR/
 iZ2+yoTU9ze+2JZ8FuCCkSfhv55iugLS8FRHUT6VdErOKnHum4aZgkHCz3oA0c5B
 FI/8pVUqEkf3wENxaM96O+XEIxF4ChMeF+fm3niMb0nL3Fiv7Sx97XExTqMhVhlv
 Xn+t71oNaU2xhus2A9Nd95oGEg9qQ2L0fvDWDV7/p+PvRRkCd0oKBVILZhVCMJ/V
 hvhbhNObUNWAb8x1pmrgWyk2H+dn4tX5SbyrbxnEAmX3oifw7CCfmZGDF+nanmMt
 cnqIjQ3qZxvQ/io6Edye0NX21K0HQcS2Bdh09uuWT+C3UNjwqGceyZdeay2gdWpP
 R7DgiaSm7+590InRweuREttVFigzOVDhN3zZTwlPGLUZ3q9EwdOcnhrPMD8ThT48
 mVWzYaPwGax3Ro3IjWsJ
 =M5iC
 -----END PGP SIGNATURE-----

Merge tag 'jfs-3.7-2' of git://github.com/kleikamp/linux-shaggy

Pull jfs fix from Dave Kleikamp:
 "Bug fix: Fix FITRIM argument handling"

* tag 'jfs-3.7-2' of git://github.com/kleikamp/linux-shaggy:
  jfs: Fix FITRIM argument handling
2012-10-23 08:49:34 +03:00
Mischa Jonker
e4b2900946 Input: serio - add ARC PS/2 driver
This adds support for the PS/2 block that is used in various ARC FPGA
platforms.

Signed-off-by: Mischa Jonker <mischa.jonker@synopsys.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-10-22 22:48:32 -07:00
Linus Torvalds
e589db7a6a Various bug fixes for ext4. The most serious of them fixes a security
bug (CVE-2012-4508) which leads to stale data exposure when we have
 fallocate racing against writes to files undergoing delayed
 allocation.  We also have two fixes for the metadata checksum feature,
 the most serious of which can cause the superblock to have a invalid
 checksum after a power failure.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABCAAGBQJQhcJVAAoJENNvdpvBGATwlc0QAJ5eRVSXoQ9DL/rpycZtWsiR
 1HofZCBbeVJq7JkazypYZPV+ncm2Nxljx61EBMpReDgx+hgJS8VD7BcjxblXT1gK
 cvIk7tYXS1E5++TWZzQd0v3GMDoMJsfzb0Ao6vefaVgqh07MKE9Zvx0L8JR4tsH1
 YlRs2/ZALFqqMficemXpDuWRRoBTEcYkvaW9PtUIpeuk9i71iSCDiHvi0mRy4dYe
 nLftjBOjcsIuK0I7DfUYrbZNQuYacFcFTM5foE6lhdT+tlL1/od2M00IpopSSjF8
 7RoqV351FqL74Stu71wDp+q9n8t8bR9gnvEuDisHXXH6PKIYo83vawvuDKtP05lt
 lF0l2nKy/QorQtUNRnrWiRshPNEplmKM1yfRXwzfq5CX4Mjox1PM9g1AfMT/Pzbq
 wNPMqtiaNnVzfcSP94MTExKMR5axFgeFsIwuCtPVNDAUEbEFuwKARIeFjCGxYYsr
 81rIKD4lgvJjaHChtE/NzslQysMmr6qiZa17s+NteCwNRJX7U4xN99SO2BXSW7lW
 xGb1ZjdESiBZGzsmuOXqAQw7KWIRS7bQ+s4dewEbqQJomPD3NQUKsRVo1wdWeUqI
 6SI1YsBYEDPiViiohsFyn1Zl3BHgIvypWMW/ChhKtYsmEJapTnJ3SR3a+eafFZ99
 HgCMCF1i0KN1tvMDrLRn
 =qL29
 -----END PGP SIGNATURE-----

Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4

Pull ext4 fixes from Ted Ts'o:
 "Various bug fixes for ext4.  The most serious of them fixes a security
  bug (CVE-2012-4508) which leads to stale data exposure when we have
  fallocate racing against writes to files undergoing delayed
  allocation.  We also have two fixes for the metadata checksum feature,
  the most serious of which can cause the superblock to have a invalid
  checksum after a power failure."

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: Avoid underflow in ext4_trim_fs()
  ext4: Checksum the block bitmap properly with bigalloc enabled
  ext4: fix undefined bit shift result in ext4_fill_flex_info
  ext4: fix metadata checksum calculation for the superblock
  ext4: race-condition protection for ext4_convert_unwritten_extents_endio
  ext4: serialize fallocate with ext4_convert_unwritten_extents
2012-10-23 08:48:26 +03:00
Linus Torvalds
344ba37bdc NFS client bugfixes for Linux 3.7
- Do not call pnfs_return_layout() from an rpciod context
 - nfs4_ds_disconnect can cause Oopses. Kill it...
 - Fix the return value for nfs_callback_start_svc
 - Fix a number of compile warnings
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQhYQSAAoJEGcL54qWCgDyX7UP/0u2lexD08QtE+rMO4+9PHeI
 6vpTqd6LURhbjZ5JGkThBHU3H8LwGb588SBMzeU6ULk5WituoBki6WCBTEw9TxCN
 4nBr9/7FEyzM/6JKSICeTs/x4ZGS+lHE2M6Q77auUj8nclykNs+oVmYCAyc1k/2J
 bL7Hz+MDLvpPLqcVthMpaSEfuPHOaawkHOD3Iqh7ZqtqcePm6K+GadD9s/pSY8RA
 8sslffyw4oEfSThaHyCuX3kcq3IL1rCez4QL986f/c1Owi8zud1c/63sSBFHpX3h
 cmQSR3R1tWNllIrwU8XD2ypVHM8RK3DFgO+KWyv9c55CCIAMeaviou9YNeWZ40d3
 iptigAjQNNzx9pMCEKtC0G/B4XLkByF9iL0/xEQzCFeX4z34mLYGpw9CpEv6bpKl
 RABPRzvJGyuodZEMxfzFKEr13M4LBV7XG6HjRt+r0ytlHOlkMil6q4sY5OhX62lG
 EwpiWx/52Lf2P7YPgkjEZeaPRq92uIX9oEGUYL1cEmXb7pVNRuPfXYtxyKy1FHXr
 xyBtbCOg/HwhYZdsHeT0C56Id0rFRP5Z+fQKdKNxyLQ9CPhpSZwAgdk/QLVeWedt
 IE5IDQpehq2v8rKyhLu08ny4YHSrUwopw6s9mZLDDFxOW9R1p23u28t50PjRSMao
 tWq7F03fspqbKeNXeB9I
 =bDBm
 -----END PGP SIGNATURE-----

Merge tag 'nfs-for-3.7-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs

Pull NFS client bugfixes from Trond Myklebust:
 - Do not call pnfs_return_layout() from an rpciod context
 - nfs4_ds_disconnect can cause Oopses.  Kill it...
 - Fix the return value for nfs_callback_start_svc
 - Fix a number of compile warnings

* tag 'nfs-for-3.7-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4: Fix the return value for nfs_callback_start_svc
  NFSv4.1: Declare osd_pri_2_pnfs_err(), objio_init_read/write to be static
  NFSv4: fs/nfs/nfs4getroot.c needs to include "internal.h"
  NFSv4.1: Use kcalloc() to allocate zeroed arrays instead of kzalloc()
  NFSv4.1: Do not call pnfs_return_layout() from an rpciod context
  NFSv4.1: Kill nfs4_ds_disconnect()
2012-10-23 08:47:38 +03:00
Linus Torvalds
c52f1dd529 regmap: Fix for dependencies for MMIO
Trivial dependency issue, not noticed before as the only user of MMIO
 also needs I2C.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQfq6dAAoJELSic+t+oim9KJMP/jp9p8GD6VDnZDXJ2BLLk1Kg
 RflVff/rwBlM8mTCK8CFbtpvEYHEMWjWP4i3cEAr8lsJmIe+fEl407SV8cW8CRpO
 iJ97JU/Vf0Juuh5ga03dRdiaaewr/uFWugU1YBKe/FWFRJD7e9L5s+P1s0axhe3N
 n5wDfYuIY6+bqxrkdrzrzSBqRf800jrR9hAsBrnlIi+f5YKvuo3QXi8zkYE/W9et
 U2uHI2ft49EIPJPNszfxn6mF193tbNABXJhn9xFluhEPl368PJCx7Q1zznrYK0va
 RyotNVIn+SLo/k9OeBVzDIX5sMoQMINCazpb3eDlJH+NMZ905KmxL/5J7ESBFSxa
 NKLAlWSNX6c9vfiGXG95P5DxoK1lY1POoDI6PI70Qf1O82e8U5qSZrE2TTcAUjdi
 3MyUDh8Mq2MEYRjjHkrtOJewY1Khz1QsA744o3Gvz9fEsSXOx8VkYdgZdUt+PHCj
 sn+2DWQA6zSK1gZqVWym6Y8nIN1e+ALYnZSGAmnfJcsHdGf3FrUbgUp1CqPmQ1Xz
 t+zscl/lQdypOk3wXkwq/lScRxRRgomeS9lHt3qpGbjuip+QKhJsJTGjcjvmnHFt
 qJOiBoPdK2Gp2hbKRRZlHx1fdt931d2ZHD2jzpZGyZz0wJE09vFhzm4V8NUH3EXu
 HX7i4ibN4DLCCoZ7Z1Im
 =DPiU
 -----END PGP SIGNATURE-----

Merge tag 'regmap-fix-mmio' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap

Pull regmap fix from Mark Brown:
 "regmap: Fix for dependencies for MMIO

  Trivial dependency issue, not noticed before as the only user of MMIO
  also needs I2C."

* tag 'regmap-fix-mmio' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: select REGMAP if REGMAP_MMIO and REGMAP_IRQ enabled
2012-10-23 08:39:38 +03:00
Alexander Duyck
1f4702aa25 ixgbe: Fix possible memory leak in ixgbe_set_ringparam
We were not correctly freeing the temporary rings on error in
ixgbe_set_ring_param.  In order to correct this I am unwinding a number of
changes that were made in order to get things back to the original working
form with modification for the current ring layouts.

This approach has multiple advantages including a smaller memory footprint,
and the fact that the interface is stopped while we are allocating the rings
meaning that there is less potential for some sort of memory corruption on the
ring.

The only disadvantage I see with this approach is that on a Rx allocation
failure we will report an error and only update the Tx rings.  However the
adapter should be fully functional in this state and the likelihood of such
an error is very low.  In addition it is not unreasonable to expect the
user to need to recheck the ring configuration should they experience an
error setting the ring sizes.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:17:19 -07:00
Don Skidmore
de52a12c29 ixgbe: Add function ixgbe_reset_pipeline_82599
This patch adds a function that forces a full pipeline reset.  This
function will be used in following patches to completely reset the PHY
during resets.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:17:05 -07:00
Alexander Duyck
505e371808 ixgbe: Drop unnecessary addition from ixgbe_set_rx_buffer_len
We still had some code floating around from the old single buffer receive
path.  As a result we were adding VLAN_HLEN to max_frame although the
resultant value was never used.  Since that is the case we can drop this from
the function.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:16:52 -07:00
Tushar Dave
71a49f777d ixgbe: Correcting small packet padding
Driver pad skb up to 17 bytes because of the HW requirement. However, that code
implementation mess up the skb tail pointer after padding. This patch sets
skb->tail correctly.

Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:16:39 -07:00
Wei Yongjun
51a1f721e2 ixgbe: using is_zero_ether_addr() to simplify the code
Using is_zero_ether_addr() to simplify the code.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:16:26 -07:00
Jacob Keller
1a71ab2491 ixgbe: (PTP) refactor init, cyclecounter and reset
This patch modifies when and where PTP registers and data are set. Previously
a work-around was used inside cyclecounter_start in order to reset some of the
time registers. This patch creates a new ixgbe_ptp_reset specifically for this
purpose. The cyclecounter configuration has trimmed down to only modify what
is necessary. Due to hardware conditions after probe and before open, PTP init
has now moved into the ixgbe_open call. This allows the ptp device name in the
sysfs to be the ethernet device name instead of the MAC address.

The cyclecounter check flag is renamed to PTP_ENABLED and is used to prevent
PTP init from happening when PTP has not been enabled.

CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:16:13 -07:00
Emil Tantilov
f8a06c2ceb ixgbe: add WOL support for new subdevice id
This patch adds a subdevice id for new 82599 device. The define is needed
to allow enabling WOL support.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:15:57 -07:00
Alexander Duyck
56e94095ef ixgbevf: Add VF DCB + SR-IOV support
This change adds support for DCB and SR-IOV from the VF.  With this change
in place the VF will correctly use a traffic class other than 0 in the case
that the PF is configured with the default user priority belonging to a
traffic class other than 0.

Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:15:35 -07:00
Alexander Duyck
bffb3bc958 ixgbe: Enable support for VF API version 1.1 in the PF.
This change switches on the last few bits for us enabling version 1.1 VF
support in the PF.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:15:17 -07:00
Alexander Duyck
f591cd9def ixgbe: Add support for GET_QUEUES message to get DCB configuration
This patch addresses several issues in regards to the combination of DCB
and SR-IOV. Specifically it allows us to send information to the VF on
which queues it should be using.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:14:54 -07:00
Alexander Duyck
107d3018ab ixgbe: Add support for tracking the default user priority to SR-IOV
It is necessary to track the default user priority in the PF so that we can
force it upon the VFs.  The motivation behind this is to keep the VFs from
getting access to user priorities meant for things like storage.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:14:32 -07:00
Alexander Duyck
a048b40e0f ixgbe: Add support for IPv6 and UDP to ixgbe_get_headlen
This change adds support for IPv6 and UDP to ixgbe_get_headlen. The
advantage to this is that we can now handle ipv4/UDP, ipv6/TCP, and
ipv6/UDP with a single memcpy instead of having to do them in multiple
pskb_may_pull calls.

A quick bit of testing shows that we increase throughput for a single
session of netperf from 8800Mpbs to about 9300Mpbs in the case of ipv6/TCP.
As such overall ipv6 performance should improve with this change.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko  <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-10-22 21:13:48 -07:00
Al Viro
80b249b71e sh: convert to generic sys_execve()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2012-10-22 22:31:12 -04:00
Al Viro
7147e21548 sh: switch to generic kernel_thread()/kernel_execve()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2012-10-22 22:31:01 -04:00
Jesper Dangaard Brouer
54d83efa44 ipvs: fix build errors related to config option combinations
Fix two build error introduced by commit 63dca2c0:
 "ipvs: Fix faulty IPv6 extension header handling in IPVS"

First build error was fairly trivial and can occur, when
CONFIG_IP_VS_IPV6 is disabled.

The second build error was tricky, and can occur when deselecting
both all Netfilter and IPVS, but selecting CONFIG_IPV6.  This is
caused by "kernel/sysctl_binary.c" including "net/ip_vs.h", which
includes "linux/netfilter_ipv6/ip6_tables.h" causing include
of "include/linux/netfilter/x_tables.h" which then cannot find
the typedef nf_hookfn.

Fix this by only including "linux/netfilter_ipv6/ip6_tables.h" in
case of CONFIG_IP_VS_IPV6 as its already used to guard the usage
of ipv6_find_hdr().

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
2012-10-23 09:23:40 +09:00
Thomas Hellstrom
b8e902f24f drm/ttm: Fix a theoretical race in ttm_bo_cleanup_refs()
In theory, that function could release the lru lock between
checking for bo on ddestroy list and a successful reserve if the bo
was already reserved, and the function was called with waiting reserves
allowed.
However, all current reservers of a bo on the ddestroy list would
atomically take the bo off the list after a successful reserve so this
race should not have been hit, so no need to backport for stable.

This patch also fixes a case found by Maarten Lankhorst where
ttm_mem_evict_first called with no_wait_gpu would incorrectly
spin waiting for bo idle if trying to evict a busy buffer that
also sits on the ddestroy list.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-10-23 10:15:21 +10:00
Thomas Hellstrom
7bc17a7837 drm/ttm: Fix a theoretical race
The ttm_mem_evict_first function could theoretically drop the
lru lock without retrying if a reservation from off the LRU list
ended up waiting.
However, since currently there are no users that could cause a wait
in that situation so this is not suitable for stable

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-10-23 10:15:17 +10:00
Thierry Reding
a16d4f8601 drm: platform: Don't initialize driver-private data
Platform device drivers usually use the driver-private data for their
own purposes. Having it overwritten by drm_platform_init() is confusing
and error-prone.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-10-23 10:15:11 +10:00
Marcin Slusarz
08bce0ac3b drm/debugfs: remove redundant info from gem_names
It's a relic of "drm: Convert proc files to seq_file and introduce debugfs",
which wrongly converted DRM_INFO + sprintf to 2 seq_printfs.

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Gamari <bgamari@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-10-23 10:15:04 +10:00
Thierry Reding
0281324516 drm: fb: cma: Fail gracefully on allocation failure
The drm_gem_cma_create() function never returns NULL but rather an error
encoded in the return value using the ERR_PTR() macro. Callers therefore
need to check for errors using the IS_ERR() macro. This change allows
drivers to handle contiguous DMA allocation failures gracefully.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-10-23 10:14:58 +10:00
Thierry Reding
e0d78d08e3 drm: fb: cma: Fix typo in debug message
The debug message showing the resolution of a framebuffer to be
allocated is missing a closing parenthesis.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-10-23 10:14:54 +10:00
Jiri Slaby
ecbbfd44a0 TTY: move tty buffers to tty_port
So this is it. The big step why we did all the work over the past
kernel releases. Now everything is prepared, so nothing protects us
from doing that big step.

           |  |            \  \ nnnn/^l      |  |
           |  |             \  /     /       |  |
           |  '-,.__   =>    \/   ,-`    =>  |  '-,.__
           | O __.´´)        (  .`           | O __.´´)
            ~~~   ~~          ``              ~~~   ~~
The buffers are now in the tty_port structure and we can start
teaching the buffer helpers (insert char/string, flip etc.) to use
tty_port instead of tty_struct all around.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:58:28 -07:00
Jiri Slaby
967fab6916 TTY: add port -> tty link
For that purpose we have to temporarily introduce a second tty back
pointer into tty_port. It is because serial layer, and maybe others,
still do not use tty_port_tty_set/get. So that we cannot set the
tty_port->tty to NULL at will now.

Yes, the fix would be to convert whole serial layer and all its users
to tty_port_tty_set/get. However we are in the process of removing the
need of tty in most of the call sites, so this would lead to a
duplicated work.

Instead we have now tty_port->itty (internal tty) which will be used
only in flush_to_ldisc. For that one it is ensured that itty is valid
wherever the work is run. IOW, the work is synchronously cancelled
before we set itty to NULL and also before hangup is processed.

After we need only tty_port and not tty_struct in most code, this
shall be changed to tty_port_tty_set/get and itty removed completely.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:53:40 -07:00
Jiri Slaby
5cff39c69b TTY: tty_buffer, cache pointer to tty->buf
During the move of tty buffers from tty_struct to tty_port, we will
need to switch all users of buf to tty->port->buf. There are many
functions where this is accessed directly in their code many times.
Cache the tty->buf pointer in such functions now and change only
single lines in each function in the next patch.

Not that it is convenient for the next patch, but the code is now also
more readable.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:53:21 -07:00
Jiri Slaby
2fc20661e3 TTY: move TTY_FLUSH* flags to tty_port
They are only TTY buffers specific. And the buffers will go to
tty_port in the next patches. So to remove the need to have both
tty_port and tty_struct at some places, let us move the flags to
tty_port.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:53:21 -07:00
Jiri Slaby
57c941212d TTY: n_tty, propagate n_tty_data
In some funtions we need only n_tty_data, so pass it down directly in
case tty is not needed there.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:53:01 -07:00
Jiri Slaby
bddc7152f6 TTY: move ldisc data from tty_struct: locks
atomic_write_lock is not n_tty specific, so move it up in the
tty_struct.

And since these are the last ones to move, remove also the comment
saying there are some ldisc' members. There are none now.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:53:01 -07:00
Jiri Slaby
ba2e68ac61 TTY: move ldisc data from tty_struct: read_* and echo_* and canon_* stuff
All the ring-buffers...

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:53:01 -07:00
Jiri Slaby
3fe780b379 TTY: move ldisc data from tty_struct: bitmaps
Here we move bitmaps and use DECLARE_BITMAP to declare them in the new
structure. And instead of memset, we use bitmap_zero as it is more
appropriate.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:53:00 -07:00
Jiri Slaby
53c5ee2cfb TTY: move ldisc data from tty_struct: simple members
Here we start moving all the n_tty related bits from tty_struct to
the newly defined n_tty_data struct in n_tty proper.

In this patch primitive members and bits are moved. The rest will be
done per-partes in the next patches.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:53:00 -07:00
Jiri Slaby
70ece7a731 TTY: n_tty, add ldisc data to n_tty
All n_tty related members from tty_struct will be moved here.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:50:54 -07:00
Jiri Slaby
6c633f27cc TTY: audit, stop accessing tty->icount
This is a private member of n_tty. Stop accessing it. Instead, take is
as an argument.

This is needed to allow clean switch of the private members to a
separate private structure of n_tty.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:50:54 -07:00
Jiri Slaby
3383427a7b TTY: n_tty, remove bogus checks
* BUG_ON(!tty) in n_tty_set_termios -- it cannot be called with tty ==
  NULL. It is called from two call sites. First, from n_tty_open where
  we have a valid tty. Second, as ld->ops->set_termios from
  tty_set_termios. But there we have a valid tty too.
* if (!tty) in n_tty_open -- why would the TTY layer call ldisc's
  open with an invalid TTY? No it indeed does not. All call sites have
  a tty and dereference that.
* BUG_ON(!tty->read_buf) in n_tty_read -- this used to be a valid
  check. The ldisc handling was broken some time ago when I added the
  check to ensure everything is OK. It still can catch the case, but
  no later than we move the buffer to ldisc data. Then there will be
  no read_buf in tty_struct, i.e. nothing to check for.
* if (!tty->read_buf) in n_tty_receive_buf -- this should never
  happen. All callers of ldisc->ops->receive_ops should hold a
  reference to an ldisc and close (which frees read_buf) cannot be
  called until the reference is dropped.
* if (WARN_ON(!tty->read_buf)) in n_tty_read -- the same as in the
  previous case.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:50:53 -07:00
Jiri Slaby
b91939f528 TTY: n_tty, simplify read_buf+echo_buf allocation
ldisc->open and close are called only once and cannot cross. So the
tests in open and close are superfluous. Remove them. (But leave sets
to NULL to ensure there is not a bug somewhere.)

And when the tests are gone, handle properly failures in open. We
leaked read_buf if allocation of echo_buf failed before. Now this is
not the case anymore.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:50:53 -07:00
Jiri Slaby
f327b340e3 TTY: hci_ldisc, remove invalid check in open
hci_ldisc's open checks if tty_struct->disc_data is set. And if so it
returns with an error. But nothing ensures disc_data to be NULL. And
since ld->ops->open shall be called only once, we do not need the
check at all. So remove it.

Note that this is not an issue now, but n_tty will start using the
disc_data pointer and this invalid 'if' would trigger then rendering
TTYs over BT unusable.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-22 16:50:53 -07:00