Use dma-direct unconditionally on arm. It has already been used for
some time for LPAE and nommu configurations.
This mostly changes the streaming mapping implementation and the (simple)
coherent allocator for device that are DMA coherent. The existing
complex allocator for uncached mappings for non-coherent devices is still
used as is using the arch_dma_alloc/arch_dma_free hooks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andre Przywara <andre.przywara@arm.com> [highbank]
Tested-by: Marc Zyngier <maz@kernel.org>
Only the footbridge platforms provide their own DMA address translation
helpers, so switch to the generic version for all other platforms, and
consolidate the footbridge implementation to remove two levels of
indirection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Use the helpers as expected by the dma-direct code in the old arm
dma-mapping code to ease a gradual switch to the common DMA code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marc Zyngier <maz@kernel.org>
virt_to_dma was only used by the now removed dmabounce code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marc Zyngier <maz@kernel.org>
With the dmabounce removal these aren't used outside of dma-mapping.c,
so mark them static. Move the dma_map_ops declarations down a bit
to avoid lots of forward declarations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marc Zyngier <maz@kernel.org>
The sa1111 platform is one of the two remaining users of the old Arm
specific "dmabounce" code, which is an earlier implementation of the
generic swiotlb.
Linus Walleij submitted a patch that removes dmabounce support from
the ixp4xx, and I had a look at the other user, which is the sa1111
companion chip.
Looking at how dmabounce is used, I could narrow it down to one driver
one three machines:
- dmabounce is only initialized on assabet/neponset, jornada720 and
badge4, which are the platforms that have an sa1111 and support
DMA on it.
- All three of these suffer from "erratum #7" that requires only
doing DMA to half the memory sections based on one of the address
lines, in addition, the neponset also can't DMA to the RAM that
is connected to sa1111 itself.
- the pxa lubbock machine also has sa1111, but does not support DMA
on it and does not set dmabounce.
- only the OHCI and audio devices on sa1111 support DMA, but as
there is no audio driver for this hardware, only OHCI remains.
In the OHCI code, I noticed that two other platforms already have
a local bounce buffer support in the form of the "local_mem"
allocator. Specifically, TMIO and SM501 use this on a few other ARM
boards with 16KB or 128KB of local SRAM that can be accessed from the
OHCI and from the CPU.
While this is not the same problem as on sa1111, I could not find a
reason why we can't re-use the existing implementation but replace the
physical SRAM address mapping with a locally allocated DMA buffer.
There are two main downsides:
- rather than using a dynamically sized pool, this buffer needs
to be allocated at probe time using a fixed size. Without
having any idea of what it should be, I picked a size of
64KB, which is between what the other two OHCI front-ends use
in their SRAM. If anyone has a better idea what that size
is reasonable, this can be trivially changed.
- Previously, only USB transfers to unaddressable memory needed
to go through the bounce buffer, now all of them do, which may
impact runtime performance for USB endpoints that do a lot of
transfers.
On the upside, the local_mem support uses write-combining buffers,
which should be a bit faster for transfers to the device compared to
normal uncached coherent memory as used in dmabounce.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The struct nhlt_format's fmt_config is a flexible array, it must not be
used as normal array.
When moving to the next nhlt_fmt_cfg we need to take into account the data
behind the ->config.caps (indicated by ->config.size).
The logic of the code also changed: it is no longer saves the _last_
fmt_cfg for all found rates.
Fixes: bc2bd45b1f ("ASoC: Intel: Skylake: Parse nhlt and register clock device")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220630065638.11183-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The present flag is only set once when one rate has been found to be saved.
This will effectively going to ignore any rate discovered at later time and
based on the code, this is not the intention.
Fixes: bc2bd45b1f ("ASoC: Intel: Skylake: Parse nhlt and register clock device")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220630065638.11183-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch fixes the wrong state of JD1 and JD2 while the bst1 or bst2 is
power on in the HDA JD using.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Reported-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/20220705101134.16792-1-oder_chiou@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Starting from ADL platform we have four HDMI PCM devices which exceeds
the size of sof_hdmi array. Since each sof_hdmi_pcm structure
represents one HDMI PCM device, we remove the sof_hdmi array and add a
new member hdmi_jack to the sof_hdmi_pcm structure to fix the
out-of-bounds problem.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220701141517.264070-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
q6apm_get_audioreach_graph() allocates a memory chunk for graph->graph
with audioreach_alloc_graph_pkt(). When idr_alloc() fails, graph->graph
is not released, which will lead to a memory leak.
We can release the graph->graph with kfree() when idr_alloc() fails to
fix the memory leak.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220629182520.2164409-1-niejianglei2021@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The register default is 0x28 per the datasheet, and the amp gain field
is supposed to be shifted left by one. With the wrong default, the ALSA
controls lie about the power-up state. With the wrong shift, we get only
half the gain we expect.
Signed-off-by: Hector Martin <marcan@marcan.st>
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-4-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC value 0xc8 is -100dB and 0xc9 is mute; this needs to map to
-100.5dB as far as the dB scale is concerned. Fix that and enable
the mute flag, so alsamixer correctly shows the control as
<0 dB .. -100 dB, mute>.
Signed-off-by: Hector Martin <marcan@marcan.st>
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix setting of FSYNC polarity in case of LEFT_J and DSP_A/B formats.
Do NOT set the SCFG field as was previously done, because that is not
correct and is also in conflict with the "ASI1 Source" control which
sets the same SCFG field!
Also add support for explicit polarity inversion.
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure there is at least 1 ms delay from reset to first command as
is specified in the datasheet. This is a fix similar to commit
307f314520 ("ASoC: tas2770: Insert post reset delay").
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For the existing msm8916 bindings the minimum reg/reg-names is 1 not 2.
Similarly the minimum interrupt/interrupt-names is 1 not 2.
Fixes: f3fc4fbfa2 ("ASoC: dt-bindings: Add SC7280 lpass cpu bindings")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220629114012.3282945-1-bryan.odonoghue@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure all AC97 interface lines are spelled in capitals,
to avoid confusing readers about where the 5th line is.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220628165840.152235-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the function arizona_aif_cfg_changed uses the TX_BCLK_RATE,
however this register is not used on wm8998. This was not noticed as
previously snd_soc_component_read did not print an error message.
However, now the log gets filled with error messages, further more the
test for if the LRCLK changed will return spurious results.
Update the code to use the RX_BCLK_RATE register, the LRCLK parameters
are written to both registers and the RX_BCLK_RATE register is used
across all Arizona devices.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220628153409.3266932-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cs47l92_put_demux returns the value of snd_soc_dapm_mux_update_power,
which returns a 1 if a path was found for the kcontrol. This is
obviously different to the expected return a 1 if the control
was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220628153409.3266932-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8998_inmux_put returns the value of snd_soc_dapm_mux_update_power,
which returns a 1 if a path was found for the kcontrol. This is
obviously different to the expected return a 1 if the control
was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220628153409.3266932-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The output compensation controls always returns zero regardless of if
the control value was updated. This results in missing notifications
to user-space of the control change. Update the handling to return 1
when the value is changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220628153409.3266932-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently slim_tx_mixer_get reports all TX mixers as enabled when
at least one is, due to it reading the entire tx_port_value bitmask
without testing the specific bit corresponding to a TX port.
Furthermore, using the same bitmask for all capture DAIs makes
setting one mixer affect them all. To prevent this, and since
the SLIM TX muxes effectively only connect to one of the mixers
at a time, turn tx_port_value into an int array storing the DAI
index each of the ports is connected to.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20220622061745.35399-1-y.oudjana@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tx_mask check doesn't reflect what the driver and the chip support.
The check currently checks for exactly two slots being enabled. The
tlv320adcx140 supports anything between one and eight channels, so relax
the check accordingly.
The tlv320adcx140 supports arbitrary tx_mask settings, but the driver
currently only supports adjacent slots beginning with the first slot,
so extend the check to check that the first slot is being used and that
there are no holes in the tx_mask.
Leave a comment to make it's the driver that limits the tx_mask
settings, not the chip itself.
While at it remove the set-but-unused struct adcx140p_priv::tdm_delay
field.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220624105716.2579539-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
max98396_dai_set_fmt() modifes register 2041 and touches bits in the mask
0x3a. Make sure to use the right mask for that operation.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-7-daniel@zonque.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to managed versions of sysfs and clk allocation to simplify
unbinding and error handling in probe. Managed sysfs node
creation specifically addresses the following error seen the second time
probe is attempted after sdma_pcm_platform_register() previously requsted
probe deferral:
sysfs: cannot create duplicate filename '/devices/platform/68000000.ocp/49022000.mcbsp/max_tx_thres'
Signed-off-by: David Owens <dowens@precisionplanting.com>
Link: https://lore.kernel.org/r/20220620183744.3176557-1-dowens@precisionplanting.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The example in audio-graph-card2.c has multiple nodes with the same name
in it. Change the port numbers to get different names.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220624092601.2445224-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Put the SGTL5000 in a silent/safe state on shutdown/remove, this is
required since the SGTL5000 produces a constant noise on its output
after it is configured and its clock is removed. Without this change
this is happening every time the module is unbound/removed or from
reboot till the clock is enabled again.
The issue was experienced on both a Toradex Colibri/Apalis iMX6, but can
be easily reproduced everywhere just playing something on the codec and
after that removing/unbinding the driver.
Fixes: 9b34e6cc3b ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220624101301.441314-1-francesco.dolcini@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the ima-modsig is enabled, the rc passed to evm_verifyxattr() may be
negative, which may cause the integer overflow problem.
Fixes: 39b0709636 ("ima: Implement support for module-style appended signatures")
Signed-off-by: Huaxin Lu <luhuaxin1@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Resolves: ERROR: else should follow close brace '}'
Signed-off-by: JeongHyeon Lee <jhs2.lee@samsung.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Rename from "tgt" to "ti" so that all of dm-table.c code uses the same
naming for dm_target variables.
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
All callers of dm_table_get_target() are expected to do proper bounds
checking on the index they pass.
Move dm_table_get_target() to dm-core.h to make it extra clear that only
DM core code should be using it. Switch it to be inlined while at it.
Standardize all DM core callers to use the same for loop pattern and
make associated variables as local as possible. Rename some variables
(e.g. s/table/t/ and s/tgt/ti/) along the way.
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
More efficient and readable to just access table->num_targets directly.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Commit 61b6e2e532 ("dm: fix BLK_STS_DM_REQUEUE handling when dm_io
represents split bio") reverted DM core's bio splitting back to using
bio_split()+bio_chain() because it was found that otherwise DM's
BLK_STS_DM_REQUEUE would trigger a live-lock waiting for bio
completion that would never occur.
Restore using bio_trim()+bio_inc_remaining(), like was done in commit
7dd76d1fee ("dm: improve bio splitting and associated IO
accounting"), but this time with proper handling for the above
scenario that is covered in more detail in the commit header for
61b6e2e532.
Solve this issue by adding a two staged dm_io requeue mechanism that
uses the new dm_bio_rewind() via dm_io_rewind():
1) requeue the dm_io into the requeue_list added to struct
mapped_device, and schedule it via new added requeue work. This
workqueue just clones the dm_io->orig_bio (which DM saves and
ensures its end sector isn't modified). dm_io_rewind() uses the
sectors and sectors_offset members of the dm_io that are recorded
relative to the end of orig_bio: dm_bio_rewind()+bio_trim() are
then used to make that cloned bio reflect the subset of the
original bio that is represented by the dm_io that is being
requeued.
2) the 2nd stage requeue is same with original requeue, but
io->orig_bio points to new cloned bio (which matches the requeued
dm_io as described above).
This allows DM core to shift the need for bio cloning from bio-split
time (during IO submission) to the less likely BLK_STS_DM_REQUEUE
handling (after IO completes with that error).
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Commit 7759eb23fd ("block: remove bio_rewind_iter()") removed
a similar API for the following reasons:
```
It is pointed that bio_rewind_iter() is one very bad API[1]:
1) bio size may not be restored after rewinding
2) it causes some bogus change, such as 5151842b9d (block: reset
bi_iter.bi_done after splitting bio)
3) rewinding really makes things complicated wrt. bio splitting
4) unnecessary updating of .bi_done in fast path
[1] https://marc.info/?t=153549924200005&r=1&w=2
So this patch takes Kent's suggestion to restore one bio into its original
state via saving bio iterator(struct bvec_iter) in bio_integrity_prep(),
given now bio_rewind_iter() is only used by bio integrity code.
```
However, saving off a copy of the 32 bytes bio->bi_iter in case rewind
needed isn't efficient because it bloats per-bio-data for what is an
unlikely case. That suggestion also ignores the need to restore
crypto and integrity info.
Add dm_bio_rewind() API for a specific use-case that is much more narrow
than the previous more generic rewind code that was reverted:
1) most bios have a fixed end sector since bio split is done from front
of the bio, if driver just records how many sectors between current
bio's start sector and the original bio's end sector, the original
position can be restored. Keeping the original bio's end sector
fixed is a _hard_ requirement for this interface!
2) if a bio's end sector won't change (usually bio_trim() isn't
called, or in the case of DM it preserves original bio), user can
restore the original position by storing sector offset from the
current ->bi_iter.bi_sector to bio's end sector; together with
saving bio size, only 8 bytes is needed to restore to original
bio.
3) DM's requeue use case: when BLK_STS_DM_REQUEUE happens, DM core
needs to restore to an "original bio" which represents the current
dm_io to be requeued (which may be a subset of the original bio).
By storing the sector offset from the original bio's end sector and
dm_io's size, dm_bio_rewind() can restore such original bio. See
commit 7dd76d1fee ("dm: improve bio splitting and associated IO
accounting") for more details on how DM does this. Leveraging this,
allows DM core to shift the need for bio cloning from bio-split
time (during IO submission) to the less likely BLK_STS_DM_REQUEUE
handling (after IO completes with that error).
4) Unlike the original rewind API, dm_bio_rewind() doesn't add .bi_done
to bvec_iter and there is no effect on the fast path.
Implement dm_bio_rewind() by factoring out clear helpers that it calls:
dm_bio_integrity_rewind, dm_bio_crypt_rewind and dm_bio_rewind_iter.
DM is able to ensure that dm_bio_rewind() is used safely but, given
the constraint that the bio's end must never change, other
hypothetical future callers may not take the same care. So make
dm_bio_rewind() and all supporting code local to DM to avoid risk of
hypothetical abuse. A "dm_" prefix was added to all functions to avoid
any namespace collisions.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Fix sparse warning:
sound/soc/fsl/fsl_utils.c:125:31: sparse: warning: Using plain integer as NULL pointer
sound/soc/fsl/fsl_utils.c:125:42: sparse: warning: Using plain integer as NULL pointer
Fixes: 7bad812554 ("ASoC: fsl_utils: Add function to handle PLL clock source")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1657192806-10569-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The bananapi R64 (BPI-R64) experiences wrong WPS button signals.
In OpenWrt pushing the WPS button while powering on the device will set
it to recovery mode. Currently, this also happens without any user
interaction. In particular, the wrong signals appear while booting the
device or restarting it, e.g. after doing a system upgrade. If the
device is in recovery mode the user needs to manually power cycle or
restart it.
The official BPI-R64 sources set the WPS button to GPIO_ACTIVE_LOW in
the device tree. This setting seems to suppress the unwanted WPS button
press signals. So this commit changes the button from GPIO_ACTIVE_HIGH to
GPIO_ACTIVE_LOW.
The official BPI-R64 sources can be found on
https://github.com/BPI-SINOVOIP/BPI-R64-openwrt
Fixes: 0b6286dd96 ("arm64: dts: mt7622: add bananapi BPI-R64 board")
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://lore.kernel.org/r/20220630111746.4098-1-vincent@systemli.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add axi clock since the driver change to DMA mode which need
to enable axi clock. And change spi clock to 26MHz as default.
Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Link: https://lore.kernel.org/r/20220630090157.29486-2-xiangsheng.hou@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This platform carries a HID compatible I2C touchscreen on the i2c4 bus,
but it may be at a different address, depending on the board model.
Add the node for a touchscreen at 0x10, but enable it only in the
final board dts.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-12-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This platform has a SPI NOR: enable support for it, completing the
storage compartment enablement for the entire platform.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-11-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
All devices of the Cherry platform have a MT6360 sub-pmic,
providing two LDOs. Add the required node to enable the PMIC
but without regulators yet, as these will be added in a
later commit.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-10-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add USB functionality by enabling the required PHYs and the XHCI
controllers.
This enables all of the supported USB ports on the Cherry boards.
Please note that u3phy1 also enables u3port1, which is configured
to be a PCI-Express PHY for the second PCIe controller that is
found on the MT8195 SoC, which will be enabled in a later commit.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This platform uses eight I2C controllers and one SPI controller:
in preparation for enabling devices attached to these controllers,
add basic configuration to enable the busses.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-8-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add gpio-line-names to document GPIO names and add the default basic
pin configuration to allow lower power operation by setting appropriate
state on the unused pins.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add mtk-sd controller and pin configuration to enable the internal
eMMC storage: now it is possible to mount a rootfs located at the
internal storage.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220704101321.44835-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
