Add intel_rapl support for the RaptorLake platform.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4516d50aab ("serial: 8250: Use canary to restart console after suspend")
Cc: stable@vger.kernel.org # v4.0+
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23 ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 states that the Modem Status
Command (MSC) shall only be used if the basic option was chosen.
The current implementation uses MSC frames even if advanced option was
chosen to inform the peer about modem line state updates. A standard
conform peer may choose to discard these frames in advanced option mode.
Furthermore, gsmtty_modem_update() is not part of the 'tty_operations'
functions despite its name.
Rename gsmtty_modem_update() to gsm_modem_update() to clarify this. Split
its function into gsm_modem_upd_via_data() and gsm_modem_upd_via_msc()
depending on the encoding and adaption. Introduce gsm_dlci_modem_output()
as adaption of gsm_dlci_data_output() to encode and queue empty frames in
advanced option mode. Use it in gsm_modem_upd_via_data().
gsm_modem_upd_via_msc() is based on the initial gsmtty_modem_update()
function which used only MSC frames to update modem states.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dynamic virtual tty registration was introduced to allow the user to handle
these cases with uevent rules. The following commits relate to this:
Commit 5b87686e32 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Commit 0b91b53323 ("tty: n_gsm: Save dlci address open status when config requester")
Commit 46292622ad ("tty: n_gsm: clean up indenting in gsm_queue()")
However, the following behavior can be seen with this implementation:
- n_gsm ldisc is activated via ioctl
- all configuration parameters are set to their default value (initiator=0)
- the mux gets activated and attached and gsmtty0 is being registered in
in gsm_dlci_open() after DLCI 0 was established (DLCI 0 is the control
channel)
- the user configures n_gsm via ioctl GSMIOC_SETCONF as initiator
- this re-attaches the n_gsm mux
- no new gsmtty devices are registered in gsmld_attach_gsm() because the
mux is already active
- the initiator side registered only the control channel as gsmtty0
(which should never happen) and no user channel tty
The commits above make it impossible to operate the initiator side as no
user channel tty is or will be available.
On the other hand, this behavior will make it also impossible to allow DLCI
parameter negotiation on responder side in the future. The responder side
first needs to provide a device for the application before the application
can set its parameters of the associated DLCI via ioctl.
Note that the user application is still able to detect a link establishment
without relaying to uevent by waiting for DTR open on responder side. This
is the same behavior as on a physical serial interface. And on initiator
side a tty hangup can be detected if a link establishment request failed.
Revert the commits above completely to always register all user channels
and no control channel after mux attachment. No other changes are made.
Fixes: 5b87686e32 ("tty: n_gsm: Modify gsmtty driver register method when config requester")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 927728a34f.
Once the uart_port->rs485->flag is set to SER_RS485_ENABLED, the port
should always work in RS485 mode. If users want the port to leave
RS485 mode, they need to call ioctl() to clear SER_RS485_ENABLED.
So here we shouldn't clear the RS485 bits in the shutdown().
Fixes: 927728a34f ("serial: sc16is7xx: Clear RS485 bits in the shutdown")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20220418094339.678144-1-hui.wang@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for KGDB in stm32 serial driver by implementing characters
polling callbacks (poll_init, poll_get_char and poll_put_char).
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Jean Philippe Romain <jean-philippe.romain@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework stm32_usart_console_putchar() function in order to anticipate
the case where the character can never be sent.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220419085330.1178925-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For historical reasons, the naming of parameters and their types in the
arm64 stacktrace code differs from that used in generic code and other
architectures, even though the types are equivalent.
For consistency and clarity, use the generic names.
There should be no functional change as a result of this patch.
Signed-off-by: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Kalesh Singh <kaleshsingh@google.com> for the series.
Link: https://lore.kernel.org/r/20220413145910.3060139-7-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Rename "struct stackframe" to "struct unwind_state" for consistency and
better naming. Accordingly, rename variable/argument "frame" to "state".
There should be no functional change as a result of this patch.
Signed-off-by: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Kalesh Singh <kaleshsingh@google.com> for the series.
Link: https://lore.kernel.org/r/20220413145910.3060139-6-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Rename unwinder functions for consistency and better naming.
- Rename start_backtrace() to unwind_init().
- Rename unwind_frame() to unwind_next().
- Rename walk_stackframe() to unwind().
There should be no functional change as a result of this patch.
Signed-off-by: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Kalesh Singh <kaleshsingh@google.com> for the series.
Link: https://lore.kernel.org/r/20220413145910.3060139-5-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that arm64 uses arch_stack_walk() consistently, struct stackframe is
only used within stacktrace.c. To make it easier to read and maintain
this code, it would be nicer if the definition were there too.
Move the definition into stacktrace.c.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Reviwed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Kalesh Singh <kaleshsingh@google.com> for the series.
Link: https://lore.kernel.org/r/20220413145910.3060139-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The comment at the top of stacktrace.c isn't all that helpful, as it's
not associated with the code which inspects the frame record, and the
code example isn't representative of common code generation today.
Delete it.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Kalesh Singh <kaleshsingh@google.com> for the series.
Link: https://lore.kernel.org/r/20220413145910.3060139-3-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, there is a check for a NULL task in unwind_frame(). It is not
needed since all current callers pass a non-NULL task.
There should be no functional change as a result of this patch.
Signed-off-by: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Kalesh Singh <kaleshsingh@google.com> for the series.
Link: https://lore.kernel.org/r/20220413145910.3060139-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Do not set timeout to twice the approximate amount of time to send the
entire FIFO if CTS is enabled. If the caller requested no timeout, e.g.
when userspace program called tcdrain(), then wait without any timeout.
Premature return from tcdrain() was observed on imx based system which
has 32 character long transmitter FIFO with hardware CTS handling.
Simple userspace application that reproduces problem has to:
* Open tty device, enable hardware flow control (CRTSCTS)
* Write data, e.g. 26 bytes
* Call tcdrain() to wait for the transmitter
* Close tty device
The other side of serial connection has to:
* Receive some data, e.g. 10 bytes
* Set RTS output (CTS input from sender perspective) inactive for
at least twice the port timeout
* Try to receive remaining data
Without this patch, userspace application will finish without any error
while the other side of connection will never receive remaining data.
Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Link: https://lore.kernel.org/r/20220228054911.1420221-1-tomasz.mon@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register a console in the ttyprintk driver so that it can be selected
for /dev/console with console=ttyprintk on the kernel command line,
similar to other console drivers.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220215141750.92808-1-vincent.whitchurch@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note: I am using a small test app + driver located at [0] for the
problem description. serco is a driver whose write function dispatches
to the serial controller. sertest is a user-mode app that writes n bytes
to the serial console using the serco driver.
While investigating a bug in the RHEL kernel, I noticed that the serial
console throughput is way below the configured speed of 115200 bps in
a HP Proliant DL380 Gen9. I was expecting something above 10KB/s, but
I got 2.5KB/s.
$ time ./sertest -n 2500 /tmp/serco
real 0m0.997s
user 0m0.000s
sys 0m0.997s
With the help of the function tracer, I then noticed the serial
controller was taking around 410us seconds to dispatch one single byte:
$ trace-cmd record -p function_graph -g serial8250_console_write \
./sertest -n 1 /tmp/serco
$ trace-cmd report
| serial8250_console_write() {
0.384 us | _raw_spin_lock_irqsave();
1.836 us | io_serial_in();
1.667 us | io_serial_out();
| uart_console_write() {
| serial8250_console_putchar() {
| wait_for_xmitr() {
1.870 us | io_serial_in();
2.238 us | }
1.737 us | io_serial_out();
4.318 us | }
4.675 us | }
| wait_for_xmitr() {
1.635 us | io_serial_in();
| __const_udelay() {
1.125 us | delay_tsc();
1.429 us | }
...
...
...
1.683 us | io_serial_in();
| __const_udelay() {
1.248 us | delay_tsc();
1.486 us | }
1.671 us | io_serial_in();
411.342 us | }
In another machine, I measured a throughput of 11.5KB/s, with the serial
controller taking between 80-90us to send each byte. That matches the
expected throughput for a configuration of 115200 bps.
This patch changes the serial8250_console_write to use the 16550 fifo
if available. In my benchmarks I got around 25% improvement in the slow
machine, and no performance penalty in the fast machine.
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Link: https://lore.kernel.org/r/20220411174841.34936-2-wander@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in sa1100_set_termios(), which is shown
below:
(Thread 1) | (Thread 2)
| sa1100_enable_ms()
sa1100_set_termios() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | sa1100_timeout()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417111626.7802-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definition of sysrq_key_table's elements, like sysrq_thaw_op and
sysrq_showallcpus_op are not consistent with sysrq_ftrace_dump_op,
Consistency makes code more readable.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Junwen Wu <wudaemon@gmail.com>
Link: https://lore.kernel.org/r/20220418153703.97705-1-wudaemon@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to initialize the count variable in lpuart_copy_rx_to_tty(),
so let's remove it here.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220418021844.29591-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some more serial drivers can be compile-tested under certain
circumstances (when building a specific architecture). So allow for
that.
This reduces the need of zillion mach/subarch-specific configs. And
since the 0day bot has only allmodconfig's for some archs, this
increases build coverage there too.
Note that cpm needs a minor update in the header, so that it drags in
at least some defines (CPM2 ones).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pic32_uart contains this:
#ifdef CONFIG_SERIAL_PIC32_CONSOLE
...
console_initcall(pic32_console_init);
...
core_initcall(pic32_late_console_init);
...
#endif
...
arch_initcall(pic32_uart_init);
When the driver is built as module, all three above become
module_init(). So if SERIAL_PIC32_CONSOLE is set while SERIAL_PIC32=m,
it results in the following build error:
In file included from include/linux/device/driver.h:21,
from include/linux/device.h:32,
from include/linux/platform_device.h:13,
from drivers/tty/serial/pic32_uart.c:12:
include/linux/module.h:131:49: error: redefinition of '__inittest'
So make sure SERIAL_PIC32_CONSOLE can be set only when SERIAL_PIC32=y --
similar as for other drivers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code wants to know if the circ buffer is empty, so use the proper
macro.
No functional change intended, just saner function name used for that
use case.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct uart_port::membase is declared as a pointer. So it should be
initialized by NULL, not zero constant.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cache port->state->xmit into a local variable (xmit) in
cdns_uart_handle_tx(). This reduces length of some lines there
significantly. I.e. makes the code more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return from the true branch of the 'if'. This saves one indentation
level and makes the code more readable.
The two comments about what obvious code does are removed too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421101708.5640-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports this issue
sunplus-uart.c:501:26: warning: symbol 'sunplus_console_ports' was not declared. Should it be static?
sunplus_console_ports is only used in sunplus-uart.c so change
its storage-class specifier to static
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220421152505.1531507-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make UART driver compatible with S4 SOC UART. Meanwhile, the S4 SOC
UART uses 12MHz as the clock source for baud rate calculations.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220422111320.19234-3-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A /2 divider over XTAL was introduced since G12A, and is preferred
to be used over the still present /3 divider since it provides much
closer frequencies vs the request baudrate. Especially the BT module
uses 3Mhz baud rate. 8Mhz calculations can lead to baud rate bias,
causing some problems.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Link: https://lore.kernel.org/r/20220422111320.19234-2-yu.tu@amlogic.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some members of struct icom_port are completely unused or only set and
never read. Remove all those.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_ops::release_port() and uart_ops::request_port() are not required
by the serial layer. So no need to define empty ones.
Remove them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use list_for_each_entry() helper instead of explicit combo of
list_for_each() and list_entry().
Note that pos is used as a reference point in list_add_tail() in
icom_alloc_adapter(). This functionality remains as with an empty list,
cur_adapter_entry->icom_adapter_entry is still the list head.
This simplifies the code a bit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The baud rates are unsigned constants. So mark them as such.
Not only it makes sense, but they are passed also to
uart_get_baud_rate() and that expects unsigned int as baud rates on
input.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point keeping the header content separated. The header was
not even protected against double inclusion. So move the content to the
appropriate source file.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a lot of sparse warnings:
.../icom.c:228:30: warning: cast from restricted __le16
.../icom.c:232:66: warning: incorrect type in assignment (different base types)
.../icom.c:232:66: expected unsigned int [usertype] leBuffer
.../icom.c:232:66: got restricted __le32 [usertype]
.../icom.c:237:30: warning: cast from restricted __le16
...
.../icom.c:1228:22: warning: cast from restricted __le16
And they are correct. So sort them all out by using proper __leXX and
uXX types and the right direction of conversion: le16_to_cpu() instead
of cpu_to_le16(), where appropriate.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Integrate both the to_icom_adapter() macro and icom_kref_release()
wrapper into icom_remove_adapter(). (And keep it icom_kref_release()
name.)
It makes the code easier to follow without complex indirections.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In icom, there is an ICOM_PORT macro to perform upcasts from struct
uart_port to struct icom_port. It's not completely safe and it works
only because the first member of icom_port is uart_port. Nowadays, we
use container_of for such an upcast instead.
So introduce a helper (to_icom_port()) with container_of in it and
convert all the ICOM_PORT users to the new helper. Apart from the code
and type safety, it's also clear what icom_port (the variable) is.
Unlike with the old ICOM_PORT (the macro with the cast).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220421085808.24152-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To move towards a more consistent behaviour between genpd and the runtime
PM core, let's start by converting genpd's time-accounting from ktime_get()
into ktime_get_mono_fast_ns().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ap_init_early function is defined a global but has no declaration,
so it produces a warning:
arch/arm/mach-versatile/integrator_ap.c:148:13: warning: no previous prototype for 'ap_init_early' [-Wmissing-prototypes
The function could be made 'static' but since it's empty, we can
just remove it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Christophe Leroy (1):
lkdtm/bugs: Don't expect thread termination without CONFIG_UBSAN_TRAP
Jiasheng Jiang (1):
lkdtm/bugs: Check for the NULL pointer after calling kmalloc
Kees Cook (4):
lkdtm/heap: Note conditions for SLAB_LINEAR_OVERFLOW
lkdtm/usercopy: Expand size of "out of frame" object
lkdtm: Move crashtype definitions into each category
lkdtm: Add CFI_BACKWARD to test ROP mitigations
-----BEGIN PGP SIGNATURE-----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=xzN7
-----END PGP SIGNATURE-----
Merge tag 'lkdtm-next' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into char-misc-next
Kees writes:
lkdtm updates for next
Christophe Leroy (1):
lkdtm/bugs: Don't expect thread termination without CONFIG_UBSAN_TRAP
Jiasheng Jiang (1):
lkdtm/bugs: Check for the NULL pointer after calling kmalloc
Kees Cook (4):
lkdtm/heap: Note conditions for SLAB_LINEAR_OVERFLOW
lkdtm/usercopy: Expand size of "out of frame" object
lkdtm: Move crashtype definitions into each category
lkdtm: Add CFI_BACKWARD to test ROP mitigations
* tag 'lkdtm-next' of https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lkdtm: Add CFI_BACKWARD to test ROP mitigations
lkdtm: Move crashtype definitions into each category
lkdtm/bugs: Don't expect thread termination without CONFIG_UBSAN_TRAP
lkdtm/usercopy: Expand size of "out of frame" object
lkdtm/heap: Note conditions for SLAB_LINEAR_OVERFLOW
lkdtm/bugs: Check for the NULL pointer after calling kmalloc
it6505 depends on DRM_DP_AUX_BUS, the kconfig for it6505 should
reflect this dependency using 'select'.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421131415.1289469-1-robert.foss@linaro.org
This contains a fix for a reported issue on sc7180 platforms, where
one of the resources has been incorrectly modelled as both clock and
interconnect, which is causing a crash when both frameworks try to
manage it. Fix the same issue also on another platform that appears
to be affected by the same.
- interconnect: qcom: sc7180: Drop IP0 interconnects
- interconnect: qcom: sdx55: Drop IP0 interconnects
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=1osk
-----END PGP SIGNATURE-----
Merge tag 'icc-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect fixes for v5.18
This contains a fix for a reported issue on sc7180 platforms, where
one of the resources has been incorrectly modelled as both clock and
interconnect, which is causing a crash when both frameworks try to
manage it. Fix the same issue also on another platform that appears
to be affected by the same.
- interconnect: qcom: sc7180: Drop IP0 interconnects
- interconnect: qcom: sdx55: Drop IP0 interconnects
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: sdx55: Drop IP0 interconnects
interconnect: qcom: sc7180: Drop IP0 interconnects
This patch fixes spurious EEXIST errors.
Extend d2df92e98a ("netfilter: nft_set_rbtree: handle element
re-addition after deletion") to deal with elements with same end flags
in the same transation.
Reset the overlap flag as described by 7c84d41416 ("netfilter:
nft_set_rbtree: Detect partial overlaps on insertion").
Fixes: 7c84d41416 ("netfilter: nft_set_rbtree: Detect partial overlaps on insertion")
Fixes: d2df92e98a ("netfilter: nft_set_rbtree: handle element re-addition after deletion")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
