Add a new system-clock-fixed flag, which can be used to specify that the
driver cannot or should not allow the clock frequency of the mapped clock
to be modified. This behavior is also implied if the system-clock-frequency
parameter is set explicitly - the flag is meant for cases where a clock is
mapped to the DAI but which is, or should be treated as, fixed.
When mclk-fs is also specified, this causes a PCM constraint to be added
which enforces that only the corresponding valid sample rate can be used.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-7-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the new system-clock-fixed flag, which can be used to specify
that the driver cannot or should not allow the clock frequency of the
mapped clock to be modified.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-6-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If an mclk-fs value was provided in the device tree configuration, the
calculated MCLK was fed into the downstream codec DAI and CPU DAI,
however set_sysclk was not being called on the platform device. Some
platform devices such as the Xilinx Audio Formatter need to know the MCLK
as well.
Call snd_soc_component_set_sysclk on each component in the stream to set
the proper sysclk value in addition to the existing call of
snd_soc_dai_set_sysclk on the codec DAI and CPU DAI. This may end up
resulting in redundant calls if one of the snd_soc_dai_set_sysclk calls
ends up calling snd_soc_component_set_sysclk itself, but that isn't
expected to cause any significant harm.
Fixes: f48dcbb6d4 ("ASoC: simple-card-utils: share asoc_simple_hw_param()")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-5-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver previously only handled the set_clkdiv divider callback when
setting the SCLK Out Divider field in the I2S Timing Control register.
However, when using the simple-audio-card driver, the set_sysclk function
is called but not set_clkdiv. This caused the divider not to be set,
leaving it at an invalid value of 0 and resulting in a very low SCLK
output rate.
Handle set_clkdiv and store the sysclk (MCLK) value for later use in
hw_params to set the SCLK Out Divider such that:
MCLK/SCLK = divider * 2
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-4-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An upcoming change will require storing additional driver data other
than the memory base address. Create a drvdata structure and use that
rather than storing the raw base address pointer.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-3-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver did not set the MM2S Fs Multiplier Register to the proper
value for playback streams. This needs to be set to the sample rate to
MCLK multiplier, or random stream underflows can occur on the downstream
I2S transmitter.
Store the sysclk value provided via the set_sysclk callback and use that
in conjunction with the sample rate in the hw_params callback to calculate
the proper value to set for this register.
Fixes: 6f6c3c36f0 ("ASoC: xlnx: add pcm formatter platform driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220120195832.1742271-2-robert.hancock@calian.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On J721s2 Linux console is on main_uart8 but to be consistent with other
J7 family of devices, alias it to ttyS2 (serial2). This also eliminates
need to have higher number of 8250 runtime UARTs.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20211223121650.26868-3-vigneshr@ti.com
Aliases are board specific and should be in board dts files.
So, move aliases to board dts and trim the list to interfaces that are
actually enabled.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20211223121650.26868-2-vigneshr@ti.com
When onlining a CPU, switch to swapper_pg_dir as soon as possible so
that it is guaranteed that the vmap'ed stack is mapped before it is
used.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
While using a plain (constant) address works, its use needlessly invokes
a SIB addressing mode, making every call site one byte larger than
necessary:
ff 14 25 98 89 42 82 call *0xffffffff82428998
Instead of using an "i" constraint with address-of operator and a 'c'
operand modifier, simply use an ordinary "m" constraint, which the
64-bit compiler will translate to %rip-relative addressing:
ff 15 62 fb d2 00 call *0xd2fb62(%rip) # ffffffff82428998 <pv_ops+0x18>
This way the compiler is also told the truth about operand usage - the
memory location gets actually read, after all.
32-bit code generation is unaffected by the change.
[ bp: Remove "we", add examples. ]
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/b8192e8a-13ef-6ac6-6364-8ba58992cd1d@suse.com
On GCC 12, the build fails due to a possible truncated string:
check.c: In function 'validate_call':
check.c:2865:58: error: '%d' directive output may be truncated writing between 1 and 10 bytes into a region of size 9 [-Werror=format-truncation=]
2865 | snprintf(pvname, sizeof(pvname), "pv_ops[%d]", idx);
| ^~
In theory it's a valid bug:
static char pvname[16];
int idx;
...
idx = (rel->addend / sizeof(void *));
snprintf(pvname, sizeof(pvname), "pv_ops[%d]", idx);
There are only 7 chars for %d while it could take up to 9, so the
printed "pv_ops[%d]" string could get truncated.
In reality the bug should never happen, because pv_ops only has ~80
entries, so 7 chars for the integer is more than enough. Still, it's
worth fixing. Bump the buffer size by 2 bytes to silence the warning.
[ jpoimboe: changed size to 19; massaged changelog ]
Fixes: db2b0c5d7b ("objtool: Support pv_opsindirect calls for noinstr")
Reported-by: Adam Borowski <kilobyte@angband.pl>
Reported-by: Martin Liška <mliska@suse.cz>
Signed-off-by: Sergei Trofimovich <slyich@gmail.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220120233748.2062559-1-slyich@gmail.com
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The flexcan IP core on the MCF5441X cannot receive CAN RTR messages
via mailboxes. However the mailbox mode is more performant. The commit
| 1c45f5778a ("can: flexcan: add ethtool support to change rx-rtr setting during runtime")
added support to switch from FIFO to mailbox mode on these cores.
After testing the mailbox mode on the MCF5441X by Angelo Dureghello,
this patch marks it (without RTR capability) as supported. Further the
IP core overview table is updated, that RTR reception via mailboxes is
not supported.
Link: https://lore.kernel.org/all/20220121084425.3141218-1-mkl@pengutronix.de
Tested-by: Angelo Dureghello <angelo@kernel-space.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The MRAM of the tcan4x5x has a size of 2K and starts at 0x8000. There
are no further registers in the tcan4x5x making 0x87fc the biggest
addressable register.
This patch fixes the max register value of the regmap config from
0x8ffc to 0x87fc.
Fixes: 6e1caaf8ed ("can: tcan4x5x: fix max register value")
Link: https://lore.kernel.org/all/20220119064011.2943292-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to optimize FIFO access, especially on m_can cores attached
to slow busses like SPI, in patch
| e39381770e ("can: m_can: Disable IRQs on FIFO bus errors")
bulk read/write support has been added to the m_can_fifo_{read,write}
functions.
That change leads to the tcan driver to call
regmap_bulk_{read,write}() with a length of 0 (for CAN frames with 0
data length). regmap treats this as an error:
| tcan4x5x spi1.0 tcan4x5x0: FIFO write returned -22
This patch fixes the problem by not calling the
cdev->ops->{read,write)_fifo() in case of a 0 length read/write.
Fixes: e39381770e ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20220114155751.2651888-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Reported-by: Michael Anochin <anochin@photo-meter.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This tcan4x5x only comes with 2K of MRAM, a RX FIFO with a dept of 32
doesn't fit into the MRAM. Use a depth of 16 instead.
Fixes: 4edd396a19 ("dt-bindings: can: tcan4x5x: Add DT bindings for TCAN4x5X driver")
Link: https://lore.kernel.org/all/20220119062951.2939851-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Brian Silverman's address at bluerivertech.com is not valid anymore,
use Brian's private email address instead.
Link: https://lore.kernel.org/all/20220110082359.2019735-1-mkl@pengutronix.de
Cc: Brian Silverman <bsilver16384@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When starting a defrag, we should update the writeback index of the
inode's mapping in case it currently has a value beyond the start of the
range we are defragging. This can help performance and often result in
getting less extents after writeback - for e.g., if the current value
of the writeback index sits somewhere in the middle of a range that
gets dirty by the defrag, then after writeback we can get two smaller
extents instead of a single, larger extent.
We used to have this before the refactoring in 5.16, but it was removed
without any reason to do so. Originally it was added in kernel 3.1, by
commit 2a0f7f5769 ("Btrfs: fix recursive auto-defrag"), in order to
fix a loop with autodefrag resulting in dirtying and writing pages over
and over, but some testing on current code did not show that happening,
at least with the test described in that commit.
So add back the behaviour, as at the very least it is a nice to have
optimization.
Fixes: 7b508037d4 ("btrfs: defrag: use defrag_one_cluster() to implement btrfs_defrag_file()")
CC: stable@vger.kernel.org # 5.16
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the systimer clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-6-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the I2C clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-5-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the Nor Flash clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-4-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the SPI clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-3-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the initial devicetree for mt8192 was added in 48489980e2 ("arm64:
dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile"), the
clock driver for mt8192 was not yet upstream, so the clock property nodes
were set to the clk26m clock as a placeholder.
Given that the clock driver has since been added through 710573dee3 ("clk:
mediatek: Add MT8192 basic clocks support"), as well as its dt-bindings
through f35f1a23e0 ("clk: mediatek: Add dt-bindings of MT8192 clocks") and
devicetree nodes through 5d2b897bc6 ("arm64: dts: mediatek: Add mt8192
clock controllers"), fix the uart clock property to point to the actual
clock.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220113065822.11809-2-allen-kh.cheng@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
A defrag operation can dirty a lot of pages, specially if operating on
the entire file or a large file range. Any task dirtying pages should
periodically call balance_dirty_pages_ratelimited(), as stated in that
function's comments, otherwise they can leave too many dirty pages in
the system. This is what we did before the refactoring in 5.16, and
it should have remained, just like in the buffered write path and
relocation. So restore that behaviour.
Fixes: 7b508037d4 ("btrfs: defrag: use defrag_one_cluster() to implement btrfs_defrag_file()")
CC: stable@vger.kernel.org # 5.16
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When defragging we can end up collecting a range for defrag that has
already pages under delalloc (dirty), as long as the respective extent
map for their range is not mapped to a hole, a prealloc extent or
the extent map is from an old generation.
Most of the time that is harmless from a functional perspective at
least, however it can result in a deadlock:
1) At defrag_collect_targets() we find an extent map that meets all
requirements but there's delalloc for the range it covers, and we add
its range to list of ranges to defrag;
2) The defrag_collect_targets() function is called at defrag_one_range(),
after it locked a range that overlaps the range of the extent map;
3) At defrag_one_range(), while the range is still locked, we call
defrag_one_locked_target() for the range associated to the extent
map we collected at step 1);
4) Then finally at defrag_one_locked_target() we do a call to
btrfs_delalloc_reserve_space(), which will reserve data and metadata
space. If the space reservations can not be satisfied right away, the
flusher might be kicked in and start flushing delalloc and wait for
the respective ordered extents to complete. If this happens we will
deadlock, because both flushing delalloc and finishing an ordered
extent, requires locking the range in the inode's io tree, which was
already locked at defrag_collect_targets().
So fix this by skipping extent maps for which there's already delalloc.
Fixes: eb793cf857 ("btrfs: defrag: introduce helper to collect target file extents")
CC: stable@vger.kernel.org # 5.16
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This adds a DT binding documentation for the MT6582 SoC.
Signed-off-by: Maxim Kutnij <gtk3@inbox.ru>
Link: https://lore.kernel.org/r/20211219183134.3849-3-gtk3@inbox.ru
[mb: fix commit subject line and compatible order]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MediaTek CPUFreq driver provides control of CPU frequency/voltage
on MediaTek SoCs. Since there's no device-tree node to bind it to, the
driver needs to be enabled built-in. Enable it so.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20211217154452.868419-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The MT6397 RTC is part of the Mediatek MT6397 PMIC, which is present in
the mt8173-elm base board.
The driver for the PMIC is already enabled through CONFIG_MFD_MT6397, so
enable just the driver for the RTC.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20211217162445.876034-1-nfraprado@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix the rx_full stats test so that it correctly reports pass even when
the fill ring is not full of buffers.
Fixes: 872a1184db ("selftests: xsk: Put the same buffer only once in the fill ring")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20220121123508.12759-1-magnus.karlsson@gmail.com
Zero-length and one-element arrays are deprecated, see:
Documentation/process/deprecated.rst
Flexible-array members should be used instead.
Generated by: scripts/coccinelle/misc/flexible_array.cocci
Fixes: c1ff181ffa ("selftests/bpf: Extend kfunc selftests")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/bpf/alpine.DEB.2.22.394.2201221206320.12220@hadrien
Renamed the to-do file to 'TODO' instead of 'ToDo' to
comply with the naming standard.
Signed-off-by: ozkanonur <onurozkan.dev@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The tools name was wrong in the SYNTAX section of the manpage it should
read "idle-set" instead of "idle-info".
Signed-off-by: Andreas Rammhold <andreas@rammhold.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
kmap() is being deprecated and these instances are easy to convert to
kmap_local_page().
Furthermore, in gma_crtc_cursor_set() use the memcpy_from_page() helper
instead of an open coded use of kmap_local_page().
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124015409.807587-4-ira.weiny@intel.com
Commit 749439bfac ("ipv6: fix udpv6
sendmsg crash caused by too small MTU") breaks PMTU for xfrm.
A Packet Too Big ICMPv6 message received in response to an ESP
packet will prevent all further communication through the tunnel
if the reported MTU minus the ESP overhead is smaller than 1280.
E.g. in a case of a tunnel-mode ESP with sha256/aes the overhead
is 92 bytes. Receiving a PTB with MTU of 1371 or less will result
in all further packets in the tunnel dropped. A ping through the
tunnel fails with "ping: sendmsg: Invalid argument".
Apparently the MTU on the xfrm route is smaller than 1280 and
fails the check inside ip6_setup_cork() added by 749439bf.
We found this by debugging USGv6/ipv6ready failures. Failing
tests are: "Phase-2 Interoperability Test Scenario IPsec" /
5.3.11 and 5.4.11 (Tunnel Mode: Fragmentation).
Commit b515d26372 ("xfrm:
xfrm_state_mtu should return at least 1280 for ipv6") attempted
to fix this but caused another regression in TCP MSS calculations
and had to be reverted.
The patch below fixes the situation by dropping the MTU
check and instead checking for the underflows described in the
749439bf commit message.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Fixes: 749439bfac ("ipv6: fix udpv6 sendmsg crash caused by too small MTU")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The gpio-tps68470 driver binds to a tps68470-gpio platform-device which
itself gets instantiated by a special MFD driver from
drivers/platform/x86/intel/int3472/tps68470.c
This MFD driver itself can be built as a module, so it makes no sense to
force the gpio-tps68470 driver to always be built-in.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove these assignment all at once.
For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
GPIO library now accepts fwnode as a firmware node, so
switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
devm_kstrdup() returns pointer to allocated string on success, NULL on
failure. So it is better to check the return value of it.
Before, if devm_kstrdup() fails, pinctrl_dev_name will be NULL, then the
retval below will be a negative error-code (inside gpiochip_add_pin_range(),
pinctrl_find_and_add_gpio_range()->get_pinctrl_dev_from_devname() will
finally check pinctrl_dev_name and return an error), so the failure of
devm_kstrdup() can be only implicitly caught after a long call chain.
While this patch is to explicitly catch the failure in time.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
SD card is allowed to signal busy on DAT0 up to 1s after the
CMD49. According to SD spec (version 6.0 section 5.8.1.3) first host
waits until busy of CMD49 is released and only then polls Power
Management Status register up to 1s until the card indicates ready to
power off.
Without waiting for busy before polling status register sometimes card
becomes unresponsive and system fails to suspend:
[ 205.907459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 206.421274] sunxi-mmc 1c0f000.mmc: data error, sending stop command
[ 206.421321] sunxi-mmc 1c0f000.mmc: send stop command failed
[ 206.421347] mmc0: error -110 reading status reg of PM func
[ 206.421366] PM: dpm_run_callback(): mmc_bus_suspend+0x0/0x74 returns -110
[ 206.421402] mmcblk mmc0:aaaa: PM: failed to suspend async: error -110
[ 206.437064] PM: Some devices failed to suspend, or early wake event detected
Tested with Sandisk Extreme PRO A2 64GB on Allwinner A64 system.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Fixes: 2c5d427690 ("mmc: core: Add support for Power Off Notification for SD cards")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220115121447.641524-1-andrej.skvortzov@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is no suitable resource, platform_get_resource() will return
NULL.
Therefore in order to avoid the dereference of the NULL pointer, it
should be better to check the 'res'.
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Cc: stable@vger.kernel.org # v5.16+
Link: https://lore.kernel.org/r/20220119120006.1426964-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
And since the sdhci_setup_host() has already checked the return value of
the enable_dma, we need not check it in sdhci_resume_host() again.
Fixes: 5552d7ad59 ("mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220112083156.1124782-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Improve non-desktop quirk logging if the EDID indicates non-desktop. If
both are set, note about redundant quirk. If there's no quirk but the
EDID indicates non-desktop, don't log non-desktop is set to 0.
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Philipp Zabel <philipp.zabel@gmail.com>
Tested-by: Philipp Zabel <philipp.zabel@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211228101051.317989-1-jani.nikula@intel.com
Now that there is support for the Microsoft VSDB for HMDs, remove the
non-desktop quirk for two devices that are verified to contain it in
their EDID: HPN-3515 and LEN-B800.
Presumably most of the other Windows Mixed Reality headsets contain it
as well, but there are ACR-7FCE and SEC-5194 devices without it.
Tested with LEN-B800.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220123101653.147333-2-philipp.zabel@gmail.com
After seeking time on testing today upstream fsdax, I found it
actually doesn't work well as below:
[ 186.492983] ------------[ cut here ]------------
[ 186.493629] WARNING: CPU: 1 PID: 205 at fs/iomap/iter.c:33 iomap_iter+0x2f6/0x310
The problem is that m_dax_part_off should be applied to physical
addresses and very sorry about that I didn't catch this eariler.
Anyway, let's fix it up now. Also, I need to find a way to set up
a standalone testcase to look after this later.
Link: https://lore.kernel.org/r/20220113051845.244461-1-hsiangkao@linux.alibaba.com
Fixes: de20511477 ("fsdax: shift partition offset handling into the file systems")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
