Some boards set the direct_irq_en flag in the conf0 register without
setting the correct trigger bits. The direct_irq_en flag just means that
the GPIO will send IRQs directly to the APIC instead of going through
the shared interrupt for the GPIO controller, in order for the pin to be
able to actually generate IRQs the trigger flags must configure the IRQ
as a level-high or level-low active IRQ.
Note testing shows that using edge trigger add the conf0 register level
does NOT work, instead edge triggering should be set at the IO-APIC level.
I believe that the direct_irq_en flag connects the output of the GPIO's IRQ
trigger block, which normally sets the status flag in the IRQ status reg at
0x800 to one of the IO-APIC pins according to the direct IRQ mux.
This means that the TRIG_LVL bit *must* be set, so that the GPIO's input
value is directly passed (1:1 or inverted) to the IO-APIC pin, if TRIG_LVL
is not set, selecting edge mode operation then on the first edge the
selected IO-APIC pin goes high, but since no write-to-clear write will be
done to the IRQ status reg at 0x800, the detected edge condition will never
get cleared.
This APIC pin stuck high condition can be observed with the pin configured
as level-high active, in the form of an interrupt storm. Clearing the
TRIG_MASK bits of conf0 stops the storm, reconfiguring them as edge again
results in a storm again as soon as the edge is triggered once.
Detect invalid trigger flags, log a FW_BUG warning when encountering this
and clear the direct_irq_en flag so that a driver can actually use the pin
as IRQ through gpiod_to_irq().
Specifically this allows the edt-ft5x06 touchscreen driver to use
INT33FC:02 pin 3 as touchscreen IRQ on the Nextbook Ares 8 tablet,
accompanied by the following new log message
byt_gpio INT33FC:02: [Firmware Bug]: pin 3: direct_irq_en set without trigger, clearing
The new byt_direct_irq_sanity_check() function also checks that the
pin is actually appointed to one of the 16 direct-IRQs which the GPIO
controller supports and on success prints debug messages like these:
byt_gpio INT33FC:02: Pin 0: uses direct IRQ 0 (IO-APIC 67)
byt_gpio INT33FC:02: Pin 15: uses direct IRQ 2 (IO-APIC 69)
This is useful to figure out the GPIO pin belonging to ACPI
resources like this one: "Interrupt () { 0x00000043 }" or
the other way around.
The strict checking of valid trigger flags this introduces does result in
FW_BUG messages on quite a few devices. E.g. on the Yoga Tablet 2 1051L:
byt_gpio INT33FC:00: [Firmware Bug]: pin 92: direct_irq_en set but no IRQ assigned, clearing
byt_gpio INT33FC:00: [Firmware Bug]: pin 93: direct_irq_en set but no IRQ assigned, clearing
These 2 also have mux set to 7 and fall + rise + level trigger bits set,
presumably something has written 0xffffffff to their conf0 registers
byt_gpio INT33FC:02: Pin 3: uses direct IRQ 1 (IO-APIC 68)
byt_gpio INT33FC:02: [Firmware Bug]: pin 3: direct_irq_en set without trigger (conf0: 2803cc00h), clearing
Most tablets seem to have this, looking at DSDTs this seems intended for
use with an I2C HID sensor-hub and is still set on devices without one.
To make sure this does not cause any regressions this has been tested,
including checking disabled direct-IRQs are not used in the DSDT,
on the following devices:
Asus ME176C
Asus TF103C
Chuwi Vi10 (with its Windows BIOS)
HP x2 10-n000nd
Lenovo Yoga Tablet 2 1050L (Android version, without EC, with buggy DSDT)
Lenovo Yoga Tablet 2 1051L (Windows version, with EC)
Suggested-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The commit af7e3eeb84 ("pinctrl: intel: Disable input and output buffer
when switching to GPIO") hadn't taken into account an update of the IRQ
flags scenario.
When updating the IRQ flags on the preconfigured line the ->irq_set_type()
is called again. In such case the sequential Rx buffer configuration
changes may trigger a falling or rising edge interrupt that may lead,
on some platforms, to an undesired event.
This may happen because each of intel_gpio_set_gpio_mode() and
__intel_gpio_set_direction() updates the pad configuration with a different
value of the GPIORXDIS bit. Notable, that the intel_gpio_set_gpio_mode() is
called only for the pads that are configured as an input. Due to this fact,
integrate the logic of __intel_gpio_set_direction() call into the
intel_gpio_set_gpio_mode() so that the Rx buffer won't be disabled and
immediately re-enabled.
Fixes: af7e3eeb84 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
Reported-by: Kane Chen <kane.chen@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Grace Kao <grace.kao@intel.com>
ASUS Chromebook C223 with Celeron N3350 crashes sometimes during
cold booot. Inspection of the kernel log showed that it gets into
an inifite loop logging the following message:
->handle_irq(): 000000009cdb51e8, handle_bad_irq+0x0/0x251
->irq_data.chip(): 000000005ec212a7, 0xffffa043009d8e7
->action(): 00000
IRQ_NOPROBE set
unexpected IRQ trap at vector 7c
The issue happens during cold boot but only if cold boot happens
at most several dozen seconds after Chromebook is powered off. For
longer intervals between power off and power on (cold boot) the issue
does not reproduce. The unexpected interrupt is sourced from INT3452
GPIO pin which is used for SD card detect. Investigation relevealed
that when the interval between power off and power on (cold boot)
is less than several dozen seconds then values of INT3452 GPIO interrupt
enable and interrupt pending registers survive power off and power
on sequence and interrupt for SD card detect pin is enabled and pending
during probe of SD controller which causes the unexpected IRQ message.
"Intel Pentium and Celeron Processor N- and J- Series" volume 3 doc
mentions that GPIO interrupt enable and status registers default
value is 0x0.
The fix clears INT3452 GPIO interrupt enabled and interrupt pending
registers in its probe function.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Keep Makefile entries ordered in the same way as Kconfig ones.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Mark the start_backtrace() as notrace and NOKPROBE_SYMBOL
because this function is called from ftrace and lockdep to
get the caller address via return_address(). The lockdep
is used in kprobes, it should also be NOKPROBE_SYMBOL.
Fixes: b07f349966 ("arm64: stacktrace: Move start_backtrace() out of the header")
Cc: <stable@vger.kernel.org> # 5.13.x
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/164301227374.1433152.12808232644267107415.stgit@devnote2
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In the WIN10 version of the Synthetic Video protocol with Hyper-V,
Hyper-V reports a list of supported resolutions as part of the protocol
negotiation. The driver calculates the maximum width and height from
the list of resolutions, and uses those maximums to validate any screen
resolution specified in the video= option on the kernel boot line.
This method of validation is incorrect. For example, the list of
supported resolutions could contain 1600x1200 and 1920x1080, both of
which fit in an 8 Mbyte frame buffer. But calculating the max width
and height yields 1920 and 1200, and 1920x1200 resolution does not fit
in an 8 Mbyte frame buffer. Unfortunately, this resolution is accepted,
causing a kernel fault when the driver accesses memory outside the
frame buffer.
Instead, validate the specified screen resolution by calculating
its size, and comparing against the frame buffer size. Delete the
code for calculating the max width and height from the list of
resolutions, since these max values have no use. Also add the
frame buffer size to the info message to aid in understanding why
a resolution might be rejected.
Fixes: 67e7cdb482 ("video: hyperv: hyperv_fb: Obtain screen resolution from Hyper-V host")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://lore.kernel.org/r/1642360711-2335-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
While at it, include directly <linux/dma-mapping.h> instead on relying on
indirect inclusion.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The async parameter of hva_to_pfn_remapped() is not used, so remove it.
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Message-Id: <20220124020456.156386-1-xianting.tian@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Zero vmcs.HOST_IA32_SYSENTER_ESP when initializing *constant* host state
if and only if SYSENTER cannot be used, i.e. the kernel is a 64-bit
kernel and is not emulating 32-bit syscalls. As the name suggests,
vmx_set_constant_host_state() is intended for state that is *constant*.
When SYSENTER is used, SYSENTER_ESP isn't constant because stacks are
per-CPU, and the VMCS must be updated whenever the vCPU is migrated to a
new CPU. The logic in vmx_vcpu_load_vmcs() doesn't differentiate between
"never loaded" and "loaded on a different CPU", i.e. setting SYSENTER_ESP
on VMCS load also handles setting correct host state when the VMCS is
first loaded.
Because a VMCS must be loaded before it is initialized during vCPU RESET,
zeroing the field in vmx_set_constant_host_state() obliterates the value
that was written when the VMCS was loaded. If the vCPU is run before it
is migrated, the subsequent VM-Exit will zero out MSR_IA32_SYSENTER_ESP,
leading to a #DF on the next 32-bit syscall.
double fault: 0000 [#1] SMP
CPU: 0 PID: 990 Comm: stable Not tainted 5.16.0+ #97
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
EIP: entry_SYSENTER_32+0x0/0xe7
Code: <9c> 50 eb 17 0f 20 d8 a9 00 10 00 00 74 0d 25 ff ef ff ff 0f 22 d8
EAX: 000000a2 EBX: a8d1300c ECX: a8d13014 EDX: 00000000
ESI: a8f87000 EDI: a8d13014 EBP: a8d12fc0 ESP: 00000000
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068 EFLAGS: 00210093
CR0: 80050033 CR2: fffffffc CR3: 02c3b000 CR4: 00152e90
Fixes: 6ab8a4053f ("KVM: VMX: Avoid to rdmsrl(MSR_IA32_SYSENTER_ESP)")
Cc: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220122015211.1468758-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the CRC PMIC we end up with multiple irq-domains with the same fwnode.
One for the irqchip which demultiplexes the actual PMIC interrupt into
interrupts for the various cells (known as the level 1 interrupts);
And 2 more for the irqchips which are part of the crystal_cove_gpio
and crystal_cove_charger cells.
This leads to the following error being printed when
CONFIG_GENERIC_IRQ_DEBUGFS is enabled:
debugfs: File '\_SB.I2C7.PMIC' in directory 'domains' already present!
Set the bus token of the main IRQ domain to DOMAIN_BUS_WIRED to avoid
this error, this also allows irq_find_matching_fwspec() to find the
right domain if necessary.
Note all 3 domain registering drivers need to set the IRQ domain bus token.
This is necessary because the IRQ domain code defaults to creating
the debugfs dir with just the fwnode name and then renames it when
the bus token is set. So each one starts with the same default name and
all 3 must be given a different name to avoid problems when one of the
other drivers loads and starts with the same default name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When we fail to expand inode from inline format to a normal format, we
restore inode to contain the original inline formatting but we forgot to
set i_lenAlloc back. The mismatch between i_lenAlloc and i_size was then
causing further problems such as warnings and lost data down the line.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 7e49b6f248 ("udf: Convert UDF to new truncate calling sequence")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
udf_expand_file_adinicb() calls directly ->writepage to write data
expanded into a page. This however misses to setup inode for writeback
properly and so we can crash on inode->i_wb dereference when submitting
page for IO like:
BUG: kernel NULL pointer dereference, address: 0000000000000158
#PF: supervisor read access in kernel mode
...
<TASK>
__folio_start_writeback+0x2ac/0x350
__block_write_full_page+0x37d/0x490
udf_expand_file_adinicb+0x255/0x400 [udf]
udf_file_write_iter+0xbe/0x1b0 [udf]
new_sync_write+0x125/0x1c0
vfs_write+0x28e/0x400
Fix the problem by marking the page dirty and going through the standard
writeback path to write the page. Strictly speaking we would not even
have to write the page but we want to catch e.g. ENOSPC errors early.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 52ebea749a ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
This driver has a bunch of custom oldstyle GPIO number-passing
fields and a custom set-up callback.
The good thing is: nothing in the kernel is using it.
Convert the driver to use GPIO descriptors with a SPI_MASTER_GPIO_SS
flag so that the local CS callback also get invoked as the hardware
needs this.
New users of this driver can provide GPIO descriptor tables like
the other converted drivers.
Cc: linux-samsung-soc@vger.kernel.org
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220119000914.192553-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the S3C64xx SPI host to use GPIO descriptors.
Provide GPIO descriptor tables for the one user with CS
0 and 1.
Cc: linux-samsung-soc@vger.kernel.org
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220118230915.157797-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI0 platform population function was taking a custom
gpio setup callback but the only user pass NULL as
argument so drop this argument.
Cc: linux-samsung-soc@vger.kernel.org
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20220118230915.157797-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The helpers to use SPI host 1 and 2 are unused in the kernel
and taking up space and maintenance hours. New systems should
use device tree and not this, so delete the code.
Cc: linux-samsung-soc@vger.kernel.org
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220118230915.157797-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add MT8186 spi-nor controller support.
MT8186 needs a new clock name, axi_s, for spi nor axi slave bus clock.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Zhen Zhang <zhen.zhang@mediatek.com>
Link: https://lore.kernel.org/r/20220118142820.2729-2-guochun.mao@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MT8186 needs axi_s clock for DMA feature.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Zhen Zhang <zhen.zhang@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220118142820.2729-5-guochun.mao@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible mediatek,mt8186-nor implementation.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Zhen Zhang <zhen.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220118142820.2729-4-guochun.mao@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Define a structure for adding more capabilities.
Add a item extra_dummy_bit for new SoCs, due to design changed.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Zhen Zhang <zhen.zhang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220118142820.2729-3-guochun.mao@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The valid regulator names for the subnodes does not match the ones
mentioned in the description.
PFUZE3000 & PFUZE3001 uses 'v33', 'vccsd' and 'vldo[1-4]' as well, so
add them to the allowed node names.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220119103747.58305-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/regulator/qcom_smd-regulator.c:1318:1-33: WARNING: Function "for_each_available_child_of_node" should have of_node_put() before return around line 1321.
Semantic patch information:
False positives can be due to function calls within the for_each
loop that may encapsulate an of_node_put.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
Fixes: 14e2976fba ("regulator: qcom_smd: Align probe function with rpmh-regulator")
CC: Konrad Dybcio <konrad.dybcio@somainline.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2201151210170.3051@hadrien
Signed-off-by: Mark Brown <broonie@kernel.org>
This is not a resource manager, it is a "Resource managed version of
regmap_add_irq_chip()". Fix the comment.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20220113144259.355845-1-luca@lucaceresoli.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the potential failure of the devm_regmap_init_mmio(), it will
return error pointer and be assigned to the regmap.
Then the error pointer will be dereferenced.
For example rx->regmap will be used in rx_macro_mclk_enable().
Therefore, it should be better to check it.
Fixes: af3d54b997 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: 809bcbcece ("ASoC: codecs: lpass-wsa-macro: Add support to WSA Macro")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220121171031.2826198-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
codec system clock source support 512FS MCLK synchronous directly, so
no need to set PLL configuration when MCLK 24.576MHz.
Suggested-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220120054012.15849-1-mac.chiang@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have new platform with rt5682s as a primary codec and rt1019 as an
amp codec. Add machine struct to register sof audio based sound card
on such Chrome machine.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: V sujith kumar Reddy <vsujithkumar.reddy@amd.com>
Link: https://lore.kernel.org/r/20220122194707.2661026-1-vsujithkumar.reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The config->pcm_hardware may be NULL when config->prealloc_buffer_size
is not zero, so it is better to move max_buffer_size assignment under
a separate condition.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1642646642-15908-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return value from io_remap_pfn_range() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Link: https://lore.kernel.org/r/20220117110357.863990-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Return value from devm_snd_soc_register_component() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220110012833.643994-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's use a more generic name, so other definitions for tlv320aic31xx
can be included.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220117132109.283365-2-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that fsl-asoc-card support setting mclk-id through the device-tree
mclk-id property, let's remove the default BCLK configuration for this
card.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Link: https://lore.kernel.org/r/20220117132109.283365-6-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sound cards may allow using different main clock inputs. In the generic
fsl-asoc-card driver, these values are hardcoded for each specific card
configuration.
Let's make it more flexible, allowing setting mclk-id from the
device-tree node. Otherwise, the default value for each card
configuration is used.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Link: https://lore.kernel.org/r/20220117132109.283365-5-ariel.dalessandro@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a board config adl_rt5682 to support alc5682 headset codec without
speaker amplifier. Follow Intel BT offload design by connecting
alc5682 to SSP0.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220120230226.175906-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to systems where iDisp HDMI/DP audio codec is disabled for some
reason, switch codecs to SoC dummy in the affected DAI links. This allows
to reuse existing topologies as hdmi_num is 3 by default.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220120230226.175906-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tx_coalesce and mii_irq are not used at all now, so remove them.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can exclude the sdw unique id and compare the sdw adr directly when
we are finding out identical parts.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220120232157.199919-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Codecs with the same part id, manufacturer id and part id, but different
sdw version should be treated as different codecs. For example, rt711 and
rt711-sdca are different. So, we should match sdw version as well.
Reported-by: Reddy Muralidhar <muralidhar.reddy@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220120232157.199919-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add system suspend functions to handle clean power-down on suspend and
restoring registers on resume.
The jack state could change during suspend. Plug->unplug and unplug->plug
are straightforward because this looks no different from any other plug
state change - there will be a plugged or unplugged interrupt pending.
The jack could be unplugged and a different type of jack plugged, and on
resume the plug state would not have changed. Setting plug_state back to
TS_TRANS (transitioning) will make the next plug interrupt after resume
run a type detection.
During system suspend any jack plug/unplug and button events will not be
reported or generate a system wakeup. If the plug state or headset type
has changed it will be reported after resume.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121120412.672284-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename jack_detect_mutex to irq_lock and make it lock the entire IRQ
handling.
The jack_detect_mutex was introduced to synchronize registering an
ALSA jack handler, via cs42l42_set_jack(), with the jack state
processing in the IRQ handler, and was taken only around the
relevant part of the IRQ handling code.
System suspend will need to synchronize with the IRQ handler thread
so will need a similar mutex that surrounds all of the IRQ handling.
Repurposing the existing jack_detect_mutex is the simplest option.
It does no harm for a call to cs42l42_set_jack() to additionally
block the first few lines of IRQ handling, and the only interrupts
used by the driver are all for jack handling.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121120412.672284-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When a plug event is detect report the full state of all status
bits, don't assume that there will have been a previous unplug
event to clear all the bits. Report the state of both HEADPHONE
and MICROPHONE bits according to detected type, and clear all the
button status bits. The current button status is already checked
and reported at the end of the function.
During a system suspend the jack could be unplugged and plugged,
possibly changing the jack type. On resume the interrupt status will
indicate a plug event - there will not be an unplug event to clear
the bits.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220121120412.672284-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
rz_ssi_stream_is_valid() never returns an int, it returns the result of
a condition which is either true or false.
While at it, drop "!!" as the expression is boolean.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220110094711.8574-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ssi parameter is unused in rz_ssi_stream_init() so just drop it.
While at it, change the return type of rz_ssi_stream_init() to void
instead of int.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220110094711.8574-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize the spinlock and make the data structures available before
registering the interrupt handlers.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220110094711.8574-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
