Enable PCIe controllers and PHYs nodes on SM8550 MTP board.
Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118230526.1499328-3-abel.vesa@linaro.org
This adds support for the aDSP, cDSP and MPSS Subsystems found in
the SM8550 SoC.
The aDSP, cDSP and MPSS needs:
- smp2p nodes to get event back from the subsystems
- remoteproc nodes with glink-edge subnodes providing all needed
resources to start and run the subsystems
In addition, the MPSS Subsystem needs a rmtfs_mem dedicated
memory zone.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115-topic-sm8550-upstream-dts-remoteproc-v3-2-815a1753de34@linaro.org
Add nodes for the Visionox VTDR6130 found on the SM8550-MTP
device.
TLMM states are also added for the Panel reset GPIO and
Tearing Effect signal for when the panel is running in
DSI Command mode.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104-topic-sm8550-upstream-dts-display-v4-3-1729cfc0e5db@linaro.org
Add devices tree nodes describing display hardware on SM8550:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs
This does not provide support for DP controllers present on the SM8550.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104-topic-sm8550-upstream-dts-display-v4-1-1729cfc0e5db@linaro.org
UFS controllers may be cache coherent and must be marked as such in the
devicetree to avoid data corruption.
This is specifically needed on recent Qualcomm platforms like SC8280XP.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230116164236.18958-1-johan+linaro@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch reports:
drivers/scsi/qla2xxx/qla_mid.c:1189:6: warning: symbol 'qla_trim_buf' was not declared. Should it be static?
drivers/scsi/qla2xxx/qla_mid.c:1221:6: warning: symbol '__qla_adjust_buf' was not declared. Should it be static?
These functions are only used in qla_mid.c, so they should be static.
Fixes: 1f8f9c3412 ("scsi: qla2xxx: edif: Reduce memory usage during low I/O")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230114013724.3943580-1-trix@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The use of kmap() is deprecated in favor of kmap_local_page().
There are two main problems with kmap(): (1) It comes with an overhead as
the mapping space is restricted and protected by a global lock for
synchronization and (2) it also requires global TLB invalidation when the
kmap’s pool wraps and it might block when the mapping space is fully
utilized until a slot becomes available.
With kmap_local_page() the mappings are per thread, CPU local, can take
page faults, and can be called from any context (including interrupts). It
is faster than kmap() in kernels with HIGHMEM enabled. Furthermore, the
tasks can be preempted and, when they are scheduled to run again, the
kernel virtual addresses are restored and still valid.
Therefore, replace kmap() with kmap_local_page() in ipr_copy_ucode_buffer()
and, instead of open-coding local mappings + memcpy() + local un-mappings,
use the better suited memcpy_to_page() helper.
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20230103182556.29080-1-fmdefrancesco@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kmap_atomic() is deprecated in favor of kmap_local_page(). Therefore,
replace kmap_atomic() with kmap_local_page() in ips_is_passthru(). In the
meantime remove an unnecessary comment, align code, and remove spaces.
kmap_atomic() is implemented like a kmap_local_page() which also disables
page-faults and preemption (the latter only for !PREEMPT_RT kernels). The
code within the mapping/unmapping in ips_is_passthru() is already in atomic
context because of a call to local_irq_save() and kmap_local_page() can be
called in atomic context too (including interrupts).
Therefore, a mere replacement of the old API with the new one is all it is
required (i.e., there is no need to explicitly add any calls to
pagefault_disable() and/or preempt_disable()).
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://lore.kernel.org/r/20230103173131.21259-1-fmdefrancesco@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux logs the error below:
$ dmesg --level=err | grep mpt
[ 7.647675] mpt3sas_cm0: Trace buffer memory 2048 KB allocated
This state does not denote an error condition (and also no warning), so
demote the level from error to info.
Cc: it+linux-scsi@molgen.mpg.de
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20230103150438.45922-1-pmenzel@molgen.mpg.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Printing a size_t value that is the result of the sizeof() operator
requires using the %z format string modifier to avoid a warning on 32-bit
architectures:
drivers/scsi/qla2xxx/qla_mid.c: In function 'qla_create_buf_pool':
drivers/scsi/qla2xxx/qla_mid.c:1094:51: error: format '%ld' expects argument of type 'long int', but argument 5 has type 'unsigned int' [-Werror=format=]
1094 | "Failed to allocate buf_map(%ld).\n", sz * sizeof(unsigned long));
| ~~^ ~~~~~~~~~~~~~~~~~~~~~~~~~~
| | |
| long int unsigned int
| %d
Fixes: 82d8dfd2a2 ("scsi: qla2xxx: edif: Fix performance dip due to lock contention")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Himanshu Madhani <himansnhu.madhani@oracle.com <mailto:himansnhu.madhani@oracle.com>>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20230117170029.2387516-1-arnd@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, available frequencies for all CPUs are appearing as 2x
of the actual frequencies. Use xo clock source as bi_tcxo in the
cpufreq-hw node to fix this.
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117093533.3710000-1-quic_pkondeti@quicinc.com
The MUIC installed is a part of SM5703 MFD, and it seems to work
the same as the SM5502 MUIC unit.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
[Apply for msm8916-samsung-j5x]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143051.547302-1-linmengbo0689@protonmail.com
Samsung Galaxy J5 2015 and 2016 have a Hall sensor on GPIO pin 52.
Add GPIO Hall sensor for them.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143037.547248-1-linmengbo0689@protonmail.com
After moving msm8916-samsung-j5.dts to msm8916-samsung-j5-common.dtsi,
Add new J5 2016 device tree.
[Add j5x device tree]
Co-developed-by: Josef W Menad <JosefWMenad@protonmail.ch>
Signed-off-by: Josef W Menad <JosefWMenad@protonmail.ch>
[Use &pm8916_usbin as USB extcon and add chassis-type for j5x]
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[Use common init device tree]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143024.547194-1-linmengbo0689@protonmail.com
The smartphones below are using the MSM8916 SoC,
which are released in 2015-2016:
Samsung Galaxy J5 2015 (SM-J500*)
Samsung Galaxy J5 2016 (SM-J510*)
Move msm8916-samsung-j5.dts to msm8916-samsung-j5-common.dtsi, and add
a common device tree for with initial support for:
- GPIO keys
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5703 MUIC)
- WCNSS (WiFi/BT)
- Regulators
The two devices (all other variants of J5 released in 2015 and J5X
released in 2016) are very similar, with some differences in display and
GPIO pins. The common parts are shared in msm8916-samsung-j5-common.dtsi
to reduce duplication.
This patch rewrites J5 2015 devices, later patches will add support for
other models.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143010.547140-1-linmengbo0689@protonmail.com
IPA is used for mobile data. Add a node describing it.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104193759.3286014-2-elder@linaro.org
Add the CPU OPP tables including core frequency and L3 bus frequency.
The L3 throughput values were chosen by studying the frequencies
available in HW LUT and picking the highest one that's less than the
CPU frequency. DDR clock rates come from the vendor kernel.
Available values from the HW LUT:
300000000
556800000
652800000
806400000
844800000
940800000
1132800000
1209600000
1286400000
1401600000
1459200000
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104171643.1004054-3-konrad.dybcio@linaro.org
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-19-dmitry.baryshkov@linaro.org
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-18-dmitry.baryshkov@linaro.org
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-17-dmitry.baryshkov@linaro.org
The slope values used during tsens calibration differ between msm8976
and msm8956 SoCs. Use SoC-specific compat value for the msm8956 SoC.
Fixes: 0484d3ce09 ("arm64: dts: qcom: Add DTS for MSM8976 and MSM8956 SoCs")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-16-dmitry.baryshkov@linaro.org
Depending on the platform, either the modem or the AP must load GSI
firmware for IPA before it can be used. To date, this has been
indicated by the presence or absence of a "modem-init" property.
That mechanism has been deprecated. Instead, we indicate how GSI
firmware should be loaded by the value of the "qcom,gsi-loader"
property.
Update all arm64 platforms that use IPA to use the "qcom,gsi-loader"
property to specify how the GSI firmware is loaded.
Update the affected nodes so the status property is last.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[bjorn: Moved sc7280 change herobrine-lte-sku]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221231002716.2367375-3-elder@linaro.org
PA_GRANULARITY is duplicated, delete one of the entries.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230114022010.27088-1-alim.akhtar@samsung.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
struct MPI2_RAID_SCSI_IO_REQUEST ends with a single SGL, but expects to
copy multiple. Add a flexible array member so the compiler can reason about
the size of the memcpy(). This will avoid the run-time false positive
warning:
memcpy: detected field-spanning write (size 128) of single field "&r1_cmd->io_request->SGL" at drivers/scsi/megaraid/megaraid_sas_fusion.c:3326 (size 16)
This change results in no binary output differences.
Reported-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Link: https://lore.kernel.org/all/88de8faa-56c4-693d-2d3-67152ee72057@diagnostix.dwd.de/
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumit Saxena <sumit.saxena@broadcom.com>
Cc: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: megaraidlinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Link: https://lore.kernel.org/r/20230106053153.never.999-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Holger Kiehl <Holger.Kiehl@dwd.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Document the new samsung-j5x device tree bindings used in its device tree.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106142956.547081-1-linmengbo0689@protonmail.com
Mike Christie <michael.christie@oracle.com> says:
The following patches were made over Martin's scsi-staging/next
branch. They add a struct that contains optinal arguments to the
scsi_execute* functions. This will be needed for the patches that
allow the SCSI passthrough users to control retries because I'm adding
a new optional argument. I separated the 2 sets to make it easier to
review and post.
Link: https://lore.kernel.org/r/20221229190154.7467-1-michael.christie@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the new SoCs added in qcom,ids.h to the soc_id array so they show
up correctly in the socinfo sysfs.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104115348.25046-5-stephan@gerhold.net
Sync the SoC IDs in qcom,ids.h with relevant entries from Qualcomm's LK
bootloader [1] that is used for almost all older Qualcomm SoCs.
Several of these are already supported, e.g.:
- MSM8960 -> APQ8060, MSM8260, ...
- MSM8976 -> APQ8076
- MSM8956 -> APQ8056
Others are currently being worked on, e.g.:
- MSM8909(W) -> APQ8009(W), MSM8905, MSM8209, ...
- MSM8939 -> MSM8239, ...
And even all remaining ones added are close enough to what is already
supported so that future support is realistic (if someone steps up to
do the work).
Add all of them at once to avoid having to add them one by one in the
future. This will also benefit other projects making use of the same
dt-bindings, e.g. bootloaders where adding support for all these SoCs
is a bit easier than on Linux.
[1]: 9d563e4a1d/platform/msm_shared/smem.h (L286)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104115348.25046-4-stephan@gerhold.net
QRD (Qualcomm Reference Design) = 0xb = 11 is used on many devices that
were originally derived from some reference design provided by Qualcomm.
Examples of existing devices in Linux would be:
- msm8916-longcheer-l8150/l8910, msm8916-wingtech-wt88047
- msm8953-xiaomi-daisy/tissot/vince
- msm8998-fxtec-pro1
- sm4250-oneplus-billie2
Add it to qcom,ids.h so the qcom,board-id properties can be rewritten
more clearly using the macros in a future patch set, i.e.
qcom,board-id = <QCOM_BOARD_ID(QRD, 1, 0) 0> instead of
qcom,board-id = <0x1000b 0x00>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104115348.25046-3-stephan@gerhold.net
The soc_id array is mostly ordered by the numeric "msm-id" defined in
qcom,ids.h but some recent entries were added at the wrong place.
While it does not make a functional difference it does make it harder
to regenerate the entire array after adding a bunch of new IDs.
Fixes: de320c07da ("soc: qcom: socinfo: Add MSM8956/76 SoC IDs to the soc_id table")
Fixes: 147f6534b8 ("soc: qcom: socinfo: Add SM8550 ID")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104115348.25046-2-stephan@gerhold.net
Depending on the platform, either the modem or the AP must load GSI
firmware for IPA before it can be used. To date, this has been
indicated by the presence or absence of a "modem-init" property.
That mechanism has been deprecated. Instead, we indicate how GSI
firmware should be loaded by the value of the "qcom,gsi-loader"
property.
Update all ARM platforms that use IPA to use the "qcom,gsi-loader"
property to specify how the GSI firmware is loaded.
Update the affected nodes so the status property is last.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221231002716.2367375-2-elder@linaro.org
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-21-dmitry.baryshkov@linaro.org
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-20-dmitry.baryshkov@linaro.org
scsi_execute() and scsi_execute_req() are no longer used so remove them.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_execute() is going to be removed. Convert cxlflash to use
scsi_execute_cmd().
[mkp: roll in fix for issue reported by sfr]
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bindings expect each pin config to come with a "function" property:
sc7280-crd-r3.dtb: pinctrl@f100000: amp-en-state: 'oneOf' conditional failed, one must be fixed:
'function' is a required property
'bias-pull-down', 'drive-strength', 'pins' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230135645.56401-9-krzysztof.kozlowski@linaro.org
Correct typo in motor pinctrl node name:
msm8916-samsung-a5u-eur.dtb: pinctrl@1000000: 'motor-en-default-stae' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230135645.56401-8-krzysztof.kozlowski@linaro.org
This fixes a regression on Inforce 6540, as the sdhci nodes no longer
overrides the platform's mmc nodes.
-----BEGIN PGP SIGNATURE-----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=T96m
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-fixes-for-6.2' into dts-for-6.3
Qualcomm ARM32 DTS fix for 6.2
This fixes a regression on Inforce 6540, as the sdhci nodes no longer
overrides the platform's mmc nodes.
