The previously added modes 3264x2448 & 1632x1224 are actually
configuring the sensor for BGGR mode, this is an issue since
the mode that is exposed through V4L incorrectly is set as GRBG.
This patch fixes the issue by moving the output crop window of
internal sensor ISP uses by one row, which means that the Bayer
pattern of the output is changed.
row 1: B G B G B G ...
row 2: G R G R G R ...
row 3: B G B G B G ...
...
row 2: G R G R G R ...
row 3: B G B G B G ...
...
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Suggested-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This control is needed for imx219 driver, as the link frequency
is independent from the pixel rate in this case, and can't be
calculated from the pixel rate.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Set/clear the bits to configure the register to expected value
to assume the v/hflip state.
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ipu3-cio2-bridge uses several features of the ACPI framework that have no
meaningful replacement when ACPI is disabled. Instead of adding #ifdefs to
the affected places, only build the bridge code if CONFIG_ACPI is enabled.
Fixes: 803abec64e ("media: ipu3-cio2: Add cio2-bridge to ipu3-cio2 driver")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2 temporary clock helper API, was introduced
in late 2012 and, as mentioned in the documentation,
meant to be replaced by the generic clock API,
once the generic clock framework became available
on all relevant architectures.
The generic clock API is a well-established API (since a few
years now). The last few media capture drivers and sensors
using v4l2-clk have been converted to the generic clock framework.
We can now remove the v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit ce548396a4 ("media: mach-omap1: board-ams-delta.c: remove soc_camera dependencies")
removed the last in-tree user of this sensor. New users
will be required to use the generic clock framework,
so it's possible to convert the driver to use it.
Convert the driver to use the CCF, and drop the legacy
v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This sensor driver has a proper device-tree binding, and also
all its platform-data based in-tree users have been converted to use
the generic clock framework.
Convert the driver to use the CCF, and drop the legacy
v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 63839882c5 ("media: mach-pxa: palmz72/pcm990: remove soc_camera dependencies")
removed the last in-tree user of this sensor. New users
will be required to use the generic clock framework,
so it's possible to convert the driver to use it.
Convert the driver to use the CCF, and drop the legacy
v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that mach-based PXA platforms are registering proper
fixed-rate clocks through the CCF, the v4l2-clk clock
is no longer required.
Drop this clock, so the driver no longer depends on the
legacy v4l2-clk API.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pxa-camera capture driver currently registers a v4l2-clk
clock, named "mclk", to represent the mt9m111 sensor clock.
Register a proper fixed-rate clock using the generic clock framework,
which will allow to remove the v4l2-clk clock in the pxa-camera
driver in a follow-up commit.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Arnd Bergmann <arnd@arndb.de> (for arch/arm/mach-*/)
Acked-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX258 sensor driver checked in device properties for a
clock-frequency property which actually does not mean that the clock is
really running such frequency or is it even enabled.
Get the provided clock and check it frequency. If none is provided,
fall back to old property.
Enable the clock when accessing the IMX258 registers and when streaming
starts with runtime PM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX258 can be used also on embedded designs using device tree so
allow the sensor to bind to a device tree node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add bindings for the IMX258 camera sensor. The bindings, just like the
driver, are quite limited, e.g. do not support regulator supplies.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only usage of rdacm20_video_ops is to assign it to the video field
in the v4l2_subdev_ops struct which is a pointer to const, and the only
usage of rdacm20_subdev_ops is to pass its address to
v4l2_i2c_subdev_init() which accepts a pointer to const. Make them const
to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adjust the initial reverse channel amplitude parsing from
firmware interface the 'maxim,reverse-channel-microvolt'
property.
This change is required for both rdacm20 and rdacm21 camera
modules to be correctly probed when used in combination with
the max9286 deserializer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instrument the function that configures the reverse channel with a
programmable amplitude value.
This change serves to prepare to adjust the reverse channel amplitude
depending on the remote end high-threshold configuration.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Break out the reverse channel setup configuration procedure to its own
function.
This change prepares for configuring the reverse channel conditionally
to the remote side high threshold configuration.
No functional changes intended.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesasa@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Document the 'maxim,reverse-channel-microvolt' vendor property in the
bindings document of the max9286 driver.
The newly introduced property allows to specify the initial
configuration of the GMSL reverse control channel to accommodate
remote serializers pre-programmed with the high threshold power
supply noise immunity enabled.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The RDACM21 is a GMSL camera supporting 1280x1080 resolution images
developed by IMI based on an Omnivision OV10640 sensor, an Omnivision
OV490 ISP and a Maxim MAX9271 GMSL serializer.
The driver uses the max9271 library module, to maximize code reuse with
other camera module drivers using the same serializer, such as rdacm20.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Writing to REG_CLKCTRL with the power off causes a hang. Enable the
device first.
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Recently ov5647.yaml got renamed as ovti,ov5647.yaml. As part of the
video-interfaces DT schema conversion that was unintentionally brought
back. Fix this by applying the schema changes to the new file and removing
the old one.
Fixes: 066a94e28a ("media: dt-bindings: media: Use graph and video-interfaces schemas")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that most users of v4l2_async_notifier_add_subdev have been converted,
let's fix the documentation so it's more clear how the v4l2-async API
should be used.
Document functions that drivers should use, and their purpose.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
kernel-doc can only correctly identify the documented function or struct
when the name in the first kernel-doc line references it. But some of the
kernel-doc blocks referenced a different function/struct then it actually
documented.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_dhcp_packet is used to read in parts of the DHCP packet and
extract relevant information for the distributed arp table. But the
structure contained the flexible member "options" which is no where used in
the code.
A sizeof on this kind of type would return the size of everything except
the flexible member. But sparse will detect this kind of sizeof and warn
with
warning: using sizeof on a flexible structure
This can be avoided by dropping the unused flexible member.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv source code was using the year of publication (to net-next)
as "last" year for the copyright statement. The whole source code mentioned
in the MAINTAINERS "BATMAN ADVANCED" section was handled as a single entity
regarding the publishing year.
This avoided having outdated (in sense of year information - not copyright
holder) publishing information inside several files. But since the simple
"update copyright year" commit (without other changes) in the file was not
well received in the upstream kernel, the option to not have a copyright
year (for initial and last publication) in the files are chosen instead.
More detailed information about the years can still be retrieved from the
SCM system.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Most -if not all- use-cases are expected to be covered by one of:
v4l2_async_notifier_add_fwnode_subdev,
v4l2_async_notifier_add_fwnode_remote_subdev or
v4l2_async_notifier_add_i2c_subdev.
We'd like to discourage drivers from using v4l2_async_notifier_add_subdev,
so rename it as __v4l2_async_notifier_add_subdev. This is
typically a good hint for drivers to avoid using the function.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are no users for vpif_display_config.asd_sizes
and vpif_display_config.asd members, which means the v4l2-async
subdevices aren't being defined anywhere.
Remove the v4l2-async, leaving only the synchronous setup.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev.
Use the appropriate helper: v4l2_async_notifier_add_i2c_subdev
or v4l2_async_notifier_add_fwnode_remote_subdev, which handles
the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_i2c_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper: v4l2_async_notifier_add_i2c_subdev
or v4l2_async_notifier_add_fwnode_remote_subdev, which handles
the needed setup, instead of open-coding it.
Using v4l2-async to allocate the driver-specific structs,
requires to change struct ceu_subdev so the embedded
struct v4l2_async_subdev is now the first element.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper: v4l2_async_notifier_add_i2c_subdev
or v4l2_async_notifier_add_fwnode_remote_subdev, which handles
the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Patch removes some useless trace events that can
be replaced by ftrace.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Use the appropriate helper v4l2_async_notifier_add_fwnode_remote_subdev,
which handles the needed setup, instead of open-coding it.
This results in removal of the now unneeded driver-specific state
struct dcmi_graph_entity, keeping track of just the source
subdevice.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The use of v4l2_async_notifier_add_subdev will be discouraged.
Drivers are instead encouraged to use a helper such as
v4l2_async_notifier_add_fwnode_remote_subdev.
This fixes a misuse of the API, as v4l2_async_notifier_add_subdev
should get a kmalloc'ed struct v4l2_async_subdev,
removing some boilerplate code while at it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change v4l2_async_notifier_add_fwnode_remote_subdev semantics
so it allocates the struct v4l2_async_subdev pointer.
This makes the API consistent: the v4l2-async subdevice addition
functions have now a unified usage model. This model is simpler,
as it makes v4l2-async responsible for the allocation and release
of the subdevice descriptor, and no longer something the driver
has to worry about.
On the user side, the change makes the API simpler for the drivers
to use and less error-prone.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The "mode_index == ARRAY_SIZE(ov5648_modes)" check ensures that we
exited the loop via a break statement so we know that "mode" must
be valid. Delete this unnecessary NULL check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The last user for this type of match was the soc-camera/sh_mobile_csi2
driver, which was removed in v4.9. If the support is ever needed,
it can always be restored.
[Sakari Ailus: Also drop DEVNAME from debug prints recently added.]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are two spelling mistakes in dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Process FIB route update events to dynamically update the stack device
rules when tunnel routing changes. Use rtnl lock to prevent FIB event
handler from running concurrently with neigh update and neigh stats
workqueue tasks. Use encap_tbl_lock mutex to synchronize with TC rule
update path that doesn't use rtnl lock.
FIB event workflow for encap flows:
- Unoffload all flows attached to route encaps from slow or fast path
depending on encap destination endpoint neigh state.
- Update encap IP header according to new route dev.
- Update flows mod_hdr action that is responsible for overwriting reg_c0
source port bits to source port of new underlying VF of new route dev. This
step requires changing flow create/delete code to save flow parse attribute
mod_hdr_acts structure for whole flow lifetime instead of deallocating it
after flow creation. Refactor mod_hdr code to allow saving id of individual
mod_hdr actions and updating them with dedicated helper.
- Offload all flows to either slow or fast path depending on encap
destination endpoint neigh state.
FIB event workflow for decap flows:
- Unoffload all route flows from hardware. When last route flow is deleted
all indirect table rules for the route dev will also be deleted.
- Update flow attr decap_vport and destination MAC according to underlying
VF of new rote dev.
- Offload all route flows back to hardware creating new indirect table
rules according to updated flow attribute data.
Extract some neigh update code to helper functions to be used by both neigh
update and route update infrastructure.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Some of the encap-specific functions and fields will also be used by route
update infrastructure in following patches. Rename them to generic names.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patch in series implement routing update event which requires
ability to modify rule match_to_reg modify header actions dynamically
during rule lifetime. In order to accommodate such behavior, refactor and
extend TC infrastructure in following ways:
- Modify mod_hdr infrastructure to preserve its parse attribute for whole
rule lifetime, instead of deallocating it after rule creation.
- Extend match_to_reg infrastructure with new function
mlx5e_tc_match_to_reg_set_and_get_id() that returns mod_hdr action id that
can be used afterwards to update the action, and
mlx5e_tc_match_to_reg_mod_hdr_change() that can modify existing actions by
its id.
- Extend tun API with new functions mlx5e_tc_tun_update_header_ipv{4|6}()
that are used to updated existing encap entry tunnel header.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in series implements route update which can cause encap
entries to migrate between routing devices. Consecutively, their parent
nhe's need to be also transferable between devices instead of having neigh
device as a part of their immutable key. Move neigh device from struct
mlx5_neigh to struct mlx5e_neigh_hash_entry and check that nhe and neigh
devices are the same in workqueue neigh update handler.
Save neigh net_device that can change dynamically in dedicated nhe->dev
field. With FIB event handler that is implemented in following patches
changing nhe->dev, NETEVENT_DELAY_PROBE_TIME_UPDATE handler can
concurrently access the nhe entry when traversing neigh list under rcu read
lock. Processing stale values in that handler doesn't change the handler
logic, so just wrap all accesses to the dev pointer in {WRITE|READ}_ONCE()
helpers.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>