Disabling all event calls is already handled by the core right before
starting the DAA process. Do not do it again when the DAA process
completes, it is redundant.
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201228105501.6104-1-miquel.raynal@bootlin.com
Add support for Silvaco I3C dual-role IP. The master role is supported
in SDR mode only. I2C transfers have not been tested but are shared
because they are very close to the I3C transfers in terms of register
configuration.
The IBI processing follows this logic:
- When a slave advertizes an interrupt (SDA pulled low) an interrupt
gets generated by the master. This time is unbounded and may be
deferred.
- The IRQ handler itself does not process anything: it only queues a
work that will be run in non-atomic context. This is needed because
short wait periods must be experienced.
- The IBI job is divided in two parts: the first one is "critical" in
the sense that it may not support getting interrupted. If this
happens, after this first section the driver checks the master error
register and depending on its content either flushes everything and
errors out, or ends the processing (this second section may be
interrupted).
- If the critical section got interrupted, the slave will
automatically respin it's IBI request when it will be allowed to.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-6-miquel.raynal@bootlin.com
Silvaco provide a dual-role I3C master.
Description is rather simple: it needs a register mapping, three
clocks and an interrupt.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-5-miquel.raynal@bootlin.com
Update a little bit the content to match the bus binding, including:
- the node title should have been named after the description done
in the historical i3c.txt file, ie: i3c-master@<address>
- child nodes should be accepted even though the drivers do not currently
support it
- #address-cells and #size-cells are also mandatory and have specific
values
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-3-miquel.raynal@bootlin.com
Attempting a conversion of the i3c.txt file to yaml schema with
minimal content changes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210121101808.14654-2-miquel.raynal@bootlin.com
Michael Kerrisk suggested that, from an API perspective, it is a bad
idea to share the PR_SYS_DISPATCH_ defines between the prctl operation
and the selector variable.
Therefore, define two new constants to be used by SUD's selector variable
and update the corresponding documentation and test cases.
While this changes the API syscall user dispatch has never been part of a
Linux release, it will show up for the first time in 5.11.
Suggested-by: Michael Kerrisk (man-pages) <mtk.manpages@gmail.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210205184321.2062251-1-krisman@collabora.com
Commit 2991552447 ("entry: Drop usage of TIF flags in the generic syscall
code") introduced a bug on architectures using the generic syscall entry
code, in which processes stopped by PTRACE_SYSCALL do not trap on syscall
return after receiving a TIF_SINGLESTEP.
The reason is that the meaning of TIF_SINGLESTEP flag is overloaded to
cause the trap after a system call is executed, but since the above commit,
the syscall call handler only checks for the SYSCALL_WORK flags on the exit
work.
Split the meaning of TIF_SINGLESTEP such that it only means single-step
mode, and create a new type of SYSCALL_WORK to request a trap immediately
after a syscall in single-step mode. In the current implementation, the
SYSCALL_WORK flag shadows the TIF_SINGLESTEP flag for simplicity.
Update x86 to flip this bit when a tracer enables single stepping.
Fixes: 2991552447 ("entry: Drop usage of TIF flags in the generic syscall code")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kyle Huey <me@kylehuey.com>
Link: https://lore.kernel.org/r/87h7mtc9pr.fsf_-_@collabora.com
The ftrace event subsystem is only created for showing the format files of
events created by the ftrace tracers, and are not trace events. The ftrace
subsystem currently has both the "enable" and "filter" files that in other
subsystems are used to enable/disable all events within the subsystem or set
a filter for all the subsystem events.
As ftrace subsystem events do not use enable or filter operations, these
files are useless in the ftrace subsystem. Remove them.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The use of strncpy is discouraged, use strscpy instead.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The media device has to be initialized and assigned to adapter->mdev
before the dvb devices are created, since that will trigger the
automatic creation of the topology.
Rework this code to achieve this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
YUV 4:4:4 is not subsampled, fix this in the docs.
Fixes: da785536e0 ("media: doc: pixfmt-yuv: Move all semi-planar YUV formats to common file")
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the first IR message, interrupts are no longer received. In addition,
the code generates a timeout IR message of 10ms but sets the timeout value
to 100ms, so no timeout was ever generated.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204317
Fixes: a49a7a4635 ("media: smipcie: add universal ir capability")
Tested-by: Laz Lev <lazlev@web.de>
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hauppauge USB QuadHD contains two two-tuner em28xx
devices behind a usb hub. Each of the four dvb adapters
contains a MaxLinear 692 combo ATSC demod/tuner.
Bus 003 Device 006: ID 2040:846d Hauppauge
Bus 003 Device 005: ID 2040:846d Hauppauge
Bus 003 Device 004: ID 04e2:0404 Exar Corp.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read errors are currently reported as write errors.
An incorrectly received read operation is never reported at all.
Add a debug statement indicating the request mismatch.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
TS2 active led is completely igored, fix that.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MaxLinear 692 is a combo demod/tuner which has ATSC and QAM
capabilities. Only ATSC is currently advertised via DVB
properties. QAM still has issues.
Confirmed working on both big and little endian. Big
endian verified on PowerPC Mac mini.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This reverts commit 1abdfe706a.
This change is broken and not solving any problem it claims to solve.
Robin reported that cpumask_local_spread() now returns any cpu out of
cpu_possible_mask in case that NOHZ_FULL is disabled (runtime or compile
time). It can also return any offline or not-present CPU in the
housekeeping mask. Before that it was returning a CPU out of
online_cpu_mask.
While the function is racy against CPU hotplug if the caller does not
protect against it, the actual use cases are not caring much about it as
they use it mostly as hint for:
- the user space affinity hint which is unused by the kernel
- memory node selection which is just suboptimal
- network queue affinity which might fail but is handled gracefully
But the occasional fail vs. hotplug is very different from returning
anything from possible_cpu_mask which can have a large amount of offline
CPUs obviously.
The changelog of the commit claims:
"The current implementation of cpumask_local_spread() does not respect
the isolated CPUs, i.e., even if a CPU has been isolated for Real-Time
task, it will return it to the caller for pinning of its IRQ
threads. Having these unwanted IRQ threads on an isolated CPU adds up
to a latency overhead."
The only correct part of this changelog is:
"The current implementation of cpumask_local_spread() does not respect
the isolated CPUs."
Everything else is just disjunct from reality.
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Nitesh Narayan Lal <nitesh@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: abelits@marvell.com
Cc: davem@davemloft.net
Link: https://lore.kernel.org/r/87y2g26tnt.fsf@nanos.tec.linutronix.de
This commit adds mixer quirks for the Pioneer DJM-900NXS2 mixer. This
device has 6 capture channels, 5 of them allow setting the signal
source. This adds controls for these, similar to the DJM-250Mk2.
However, playpack channels are not controllable via software like on the
250Mk2, as they can only be set manually on the mixing console.
Read-only controls showing the currently selected playback channels are
omitted.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Link: https://lore.kernel.org/r/20210205215116.258724-2-fabian@lesniak-it.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows for N different devices to use the pioneer mixer quirk for
setting capture/record type and recording level. The impementation has
not changed much with the exception of an additional mask on
private_value to allow storing of a device index:
DEVICE MASK 0xff000000
GROUP_MASK 0x00ff0000
VALUE_MASK 0x0000ffff
This could be improved by changing the arrays of wValues for each
channel to contain named definitions (e.g. SND_DJM_CAP_LINE). It would
improve readability and perhaps would allow using the same array for
multiple channels. The channel number can be specified on the control
next to the wIndex.
Feedback is very much appreciated as I'm not the most proficient C
programmer but am learning as I go.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210205184256.10201-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge misc fixes from Andrew Morton:
"18 patches.
Subsystems affected by this patch series: mm (hugetlb, compaction,
vmalloc, shmem, memblock, pagecache, kasan, and hugetlb), mailmap,
gcov, ubsan, and MAINTAINERS"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS/.mailmap: use my @kernel.org address
mm: hugetlb: fix missing put_page in gather_surplus_pages()
ubsan: implement __ubsan_handle_alignment_assumption
kasan: make addr_has_metadata() return true for valid addresses
kasan: add explicit preconditions to kasan_report()
mm/filemap: add missing mem_cgroup_uncharge() to __add_to_page_cache_locked()
mailmap: add entries for Manivannan Sadhasivam
mailmap: fix name/email for Viresh Kumar
memblock: do not start bottom-up allocations with kernel_end
mm: thp: fix MADV_REMOVE deadlock on shmem THP
init/gcov: allow CONFIG_CONSTRUCTORS on UML to fix module gcov
mm/vmalloc: separate put pages and flush VM flags
mm, compaction: move high_pfn to the for loop scope
mm: migrate: do not migrate HugeTLB page whose refcount is one
mm: hugetlb: remove VM_BUG_ON_PAGE from page_huge_active
mm: hugetlb: fix a race between isolating and freeing page
mm: hugetlb: fix a race between freeing and dissolving the page
mm: hugetlbfs: fix cannot migrate the fallocated HugeTLB page
Since commit 9ed5af268e ("SUNRPC: Clean up the handling of page
padding in rpc_prepare_reply_pages()") [Dec 2020] the NFS client
passes payload data to the transport with the padding in xdr->pages
instead of in the send buffer's tail kvec. There's no need for the
extra logic to advance the base of the tail kvec because the upper
layer no longer places XDR padding there.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The file /sys/kernel/tracing/events/enable is used to enable all events by
echoing in "1", or disabling all events when echoing in "0". To know if all
events are enabled, disabled, or some are enabled but not all of them,
cating the file should show either "1" (all enabled), "0" (all disabled), or
"X" (some enabled but not all of them). This works the same as the "enable"
files in the individule system directories (like tracing/events/sched/enable).
But when all events are enabled, the top level "enable" file shows "X". The
reason is that its checking the "ftrace" events, which are special events
that only exist for their format files. These include the format for the
function tracer events, that are enabled when the function tracer is
enabled, but not by the "enable" file. The check includes these events,
which will always be disabled, and even though all true events are enabled,
the top level "enable" file will show "X" instead of "1".
To fix this, have the check test the event's flags to see if it has the
"IGNORE_ENABLE" flag set, and if so, not test it.
Cc: stable@vger.kernel.org
Fixes: 553552ce17 ("tracing: Combine event filter_active and enable into single flags field")
Reported-by: "Yordan Karadzhov (VMware)" <y.karadz@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Since commit a85a6c86c2 ("driver core: platform: Clarify that IRQ 0
is invalid"), having a linux-irq with number 0 will trigger a WARN()
when calling platform_get_irq*() to retrieve that linux-irq.
Since [devm_]irq_alloc_desc allocs a single irq and since irq 0 is not used
on some systems, it can return 0, triggering that WARN(). This happens
e.g. on Intel Bay Trail and Cherry Trail devices using the LPE audio engine
for HDMI audio:
0 is an invalid IRQ number
WARNING: CPU: 3 PID: 472 at drivers/base/platform.c:238 platform_get_irq_optional+0x108/0x180
Modules linked in: snd_hdmi_lpe_audio(+) ...
Call Trace:
platform_get_irq+0x17/0x30
hdmi_lpe_audio_probe+0x4a/0x6c0 [snd_hdmi_lpe_audio]
---[ end trace ceece38854223a0b ]---
Change the 'from' parameter passed to __[devm_]irq_alloc_descs() by the
[devm_]irq_alloc_desc macros from 0 to 1, so that these macros will no
longer return 0.
Fixes: a85a6c86c2 ("driver core: platform: Clarify that IRQ 0 is invalid")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201221185647.226146-1-hdegoede@redhat.com
The check for a NULL pf pointer is moot since the earlier declaration and
assignment of struct device *dev already de-referenced the pointer. Also,
the only caller of ice_set_dflt_mib() already ensures pf is not NULL.
Cc: Dave Ertman <david.m.ertman@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the flex_array_size() helper with the recently added flexible array
members in structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in
struct ice_res_tracker, instead of a one-element array and use the
struct_size() helper to calculate the size for the allocations.
Also, notice that the code below suggests that, currently, two too many
bytes are being allocated with devm_kzalloc(), as the total number of
entries (pf->irq_tracker->num_entries) for pf->irq_tracker->list[] is
_vectors_ and sizeof(*pf->irq_tracker) also includes the size of the
one-element array _list_ in struct ice_res_tracker.
drivers/net/ethernet/intel/ice/ice_main.c:3511:
3511 /* populate SW interrupts pool with number of OS granted IRQs. */
3512 pf->num_avail_sw_msix = (u16)vectors;
3513 pf->irq_tracker->num_entries = (u16)vectors;
3514 pf->irq_tracker->end = pf->irq_tracker->num_entries;
With this change, the right amount of dynamic memory is now allocated
because, contrary to one-element arrays which occupy at least as much
space as a single object of the type, flexible-array members don't
occupy such space in the containing structure.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9-rc1/process/deprecated.html#zero-length-and-one-element-arrays
Built-tested-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Just as we recently added support for other stored firmware flash
versions, support display of the stored UNDI Option ROM version via
devlink info.
To do this, we need to introduce a new ice_get_inactive_orom_ver
function. This is a little trickier than with other flash versions. The
Option ROM version data was being read from a special "Boot
Configuration" block of the NVM Preserved Field Area. This block only
contains the *active* Option ROM version data. It is populated when the
device firmware finishes updating the Option ROM.
This method is ineffective at reading the stored Option ROM version
data. Instead of reading from this section of the flash, replace this
version extraction with one which locates the Combo Version information
from within the Option ROM binary.
This data is stored within the Option ROM at a 512 byte offset, in
a simple structured format. The structure uses a simple modulo 256
checksum for integrity verification. Scan through the Option ROM to
locate the CIVD data section, and extract the Combo Version.
Refactor ice_get_orom_ver_info so that it takes the bank select
enumeration parameter. Use this to implement ice_get_inactive_orom_ver.
Although all ice devices have a Boot Configuration block in the NVM PFA,
not all devices have a valid Option ROM. In this case, the old
ice_get_orom_ver_info would "succeed" but report a version of all
zeros. The new implementation would fail to locate the $CIV section in
the Option ROM and report an error. Thus, we must ensure that
ice_init_nvm does not fail if ice_get_orom_ver_info fails.
Use the new ice_get_inactive_orom_ver to allow reporting the Option ROM
versions for a pending update via devlink info.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The devlink info interface supports drivers reporting "stored" versions.
These versions indicate the version of an update that has been
downloaded to the device, but is not yet active.
The code for extracting the NVM version recently changed to enable
support for reading from either the active or the inactive bank. Use
this to implement ice_get_inactive_nvm_ver, which will read the NVM
version data from the inactive section of flash.
When reporting the versions via devlink info, first read the device
capabilities. Determine if there is a pending flash update, and if so,
extract relevant version information from the inactive flash. Store
these within the info context structure.
When reporting "stored" firmware versions, devlink documentation
indicates that we ought to always report a stored value, even if there
is no pending update. In this common case, the stored version should
match the running version. This means that each stored version should by
default fallback to the same value as reported by the running handler.
To support this, modify the version structure to have both a "getter"
and a "fallback". Modify the control loop so that it will use the
"fallback" function if the "getter" function does not report a version.
To report versions for which we can read the stored value, use a new
"stored()" macro. This macro will insert two entries into the version
list. The first entry is the traditional running version. The second is
the stored version, implemented with a fallback to the active version.
This is a little tricky, but reduces the overall duplication of elements
in the entry list, and ensures that running and stored values remain
consistent.
To avoid some duplication, add a combined() macro that will insert both
the running and stored versions into the version entry list.
Using this new support, add pending version reporter functions for
"fw.psid.api" and "fw.bundle_id". This enables reporting the stored
values for some of versions in the NVM module of the flash.
Reporting management versions is not implemented by this patch. The
active management version is reported to the driver via the AdminQ
mailbox during load. Although the version must be in the firmware binary
somewhere, accessing this from the inactive firmware is not trivial and
has not been implemented in this change.
Future changes will introduce support for reading the UNDI Option ROM
version and the version associated with the Netlist module.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When reading from the flash memory of the device, the ice driver has two
interfaces available to it. First, it can use a mediated interface via
firmware that allows specifying a module ID. This allows reading from
specific modules of the active flash bank.
The second interface available is to perform flat reads. This allows
complete access to the entire flash. However, using it requires the
software to handle calculating module location and interpret pointer
addresses.
While most data required is accessible through the convenient first
interface, certain flash contents are not. This includes the CSS header
information associated with the Option ROM and NVM banks, as well as any
access to the "inactive" banks used as scratch space for performing
flash updates.
In order to access all of the relevant flash contents, software must use
the flat reads. Rather than forcing all flows to perform flat read
calculations, introduce a new abstraction for reading from the flash:
ice_read_flash_module. This function provides an abstraction for reading
from either the active or inactive flash bank at the requested module.
This interface is very similar to the abstraction provided via firmware,
but allows access to additional modules, as well as providing
a mechanism to request access to both flash banks.
At first glance, it might make sense for this abstraction to allow
specifying precisely which bank (1st or 2nd) the caller wishes to read.
This is simpler to implement but more difficult to use. In practice,
most callers only know whether they want the active bank, or the
inactive bank. Rather than force callers to determine for themselves
which bank to read from, implement ice_read_flash_module in terms of
"active" vs "inactive". This significantly simplifies the implementation
at the caller level and is a more useful abstraction over the flash
contents.
Make use of this new interface to refactor reading of the main NVM
version information. Instead of using the firmware's mediated ShadowRAM
function, use the ice_read_flash_module abstraction.
To do this, notice that most reads of the NVM are going to be in 2-byte
word chunks. To simplify using ice_read_flash_module for this case,
ice_read_nvm_module is introduced. This is a simple wrapper around
ice_read_flash_module which takes the correct pointer address for the
NVM bank, and forces the 2-byte word format onto the caller.
When reading the NVM versions, some fields are read from the Shadow RAM.
The Shadow RAM is the first 64KB of flash memory, and is populated
during device load. Most fields are copied from a section within the
active NVM bank. In order to read this data from both the active and
inactive NVM banks, we need to read not from the first 64KB of flash,
but instead from the correct offset into the NVM bank. Introduce
ice_read_nvm_sr_copy for this purpose. This function wraps around
ice_read_nvm_module and has the same interface as the ice_read_sr_word,
with the exception of allowing the caller to specify whether to read the
active or inactive flash bank.
With this change, it is now trivial to refactor ice_get_nvm_ver_info to
read using the software mediated ice_read_flash_module interface instead
of relying on the firmware mediated interface. This will be used in the
following change to implement support for stored versions in the devlink
info report.
Additionally, the overall ice_read_flash_module interface will be used
and extended to support all three major flash banks, and additionally to
support reading the flash image security revision information.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice flash contains two copies of each of the NVM, Option ROM, and
Netlist modules. Each bank has a pointer word and a size word. In order
to correctly read from the active flash bank, the driver must calculate
the offset manually.
During NVM initialization, read the Shadow RAM control word and
determine which bank is active for each NVM module. Additionally, cache
the size and pointer values for use in calculating the correct offset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver uses an array of structures which link an info name with
a function that formats the associated version data into a string.
All existing format functions simply format already captured static data
from the driver hw structure. Future changes will introduce format
functions for reporting the versions of flash sections stored but not
yet applied. This type of version data is not stored as a member of the
hw structure. This is because (a) it might not yet exist in the case
there is no pending flash update, and (b) even if it does, it might
change such as if an update is canceled or replaced by a new update
before finalizing.
We could simply have each format function gather its own data upon being
called. However, in some cases the raw binary version data is
a combination of multiple different reported fields. Additionally, the
current interface doesn't have a way for the function to indicate that
the version doesn't exist.
Refactor this function interface to take a new ice_info_ctx structure
instead of the buffer pointer and length. This context structure allows
for future extensions to pre-gather version data that is stored within
the context struct instead of the hw struct.
Allocate this context structure initially at the start of
ice_devlink_info_get. We use dynamic allocation instead of a local stack
variable in order to avoid using too much kernel stack once we extend it
with additional data structures.
Modify the main loop that drives the info reporting so that the version
buffer string is always cleared between each format. Explicitly check
that the format function actually filled in a version string of non-zero
length. If the string is not provided, simply skip this version without
reporting an error. This allows for introducing format functions of
versions which may or may not be present, such as the version of
a pending update that has not yet been activated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_nvm_info structure has become somewhat of a dumping ground for
all of the fields related to flash version. It holds the NVM version and
EETRACK id, the OptionROM info structure, the flash size, the ShadowRAM
size, and more.
A future change is going to add the ability to read the NVM version and
EETRACK ID from the inactive NVM bank. To make this simpler, it is
useful to have these NVM version info fields extracted to their own
structure.
Rename ice_nvm_info into ice_flash_info, and create a separate
ice_nvm_info structure that will contain the eetrack and NVM map
version. Move the netlist_ver structure into ice_flash_info and rename it
ice_netlist_info for consistency.
Modify the static ice_get_orom_ver_info to take the option rom structure
as a pointer. This makes it more obvious what portion of the hw struct
is being modified. Do the same for ice_get_netlist_ver_info.
Introduce a new ice_get_nvm_ver_info function, which will be similar to
ice_get_orom_ver_info and ice_get_netlist_ver_info, used to keep the NVM
version extraction code co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Assuming
- //HOST/a is mounted on /mnt
- //HOST/b is mounted on /mnt/b
On a slow connection, running 'df' and killing it while it's
processing /mnt/b can make cifs_get_inode_info() returns -ERESTARTSYS.
This triggers the following chain of events:
=> the dentry revalidation fail
=> dentry is put and released
=> superblock associated with the dentry is put
=> /mnt/b is unmounted
This patch makes cifs_d_revalidate() return the error instead of 0
(invalid) when cifs_revalidate_dentry() fails, except for ENOENT (file
deleted) and ESTALE (file recreated).
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Suggested-by: Shyam Prasad N <nspmangalore@gmail.com>
Reviewed-by: Shyam Prasad N <nspmangalore@gmail.com>
CC: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
We do not expect to receive spurious interrupts so rise a warning
if it happens.
RX overrun is an error condition that signals a corrupted RX
stream both in dma and in irq modes. Report the error and
abort the transfer in either cases.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-9-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace SPI_1HZ_NS private constant with NSEC_PER_SEC, which is easier
to read and understand.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-8-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Defer the probe operation when a reset controller device is expected
but have not yet been probed.
This change replaces use of devm_reset_control_get_exclusive() with
devm_reset_control_get_optional_exclusive() as reset controller is
optional which is now explicitly stated.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1612551572-495-7-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>