Even though our HW supports PSR + VRR, the available panels
do not work reliably with PSR and VRR together. So if user
requested VRR and is supported by HW enable that and do not
enable PSR in that case.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-7-manasi.d.navare@intel.com
This forces a complete modeset if vrr drm crtc state goes
from enabled to disabled and vice versa.
This patch also computes vrr state variables from the mode timings
and based on the vrr property set by userspace as well as hardware's
vrr capability.
v2:
*Rebase
v3:
* Vmin = max (vtotal, vmin) (Manasi)
v4:
* set crtc_state->vrr.enable = 0 for disable request
v5:
* drm_dbg_kms, squash crtc states def patch (Jani N)
v6:
* Move vrr modeset check to separate function (Jani N)
v7:
* Ville's fixes - vmin, vmax rename, fix rounding dir
* Add pipeline full, flipline to crtc state
* Pass conn state to vrr_compute_config (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-6-manasi.d.navare@intel.com
We want to calculate the vblank_start for vblank evasion
differently for vrr. To make that nicer lets first extract
the current non-vrr case to a helper.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-4-manasi.d.navare@intel.com
The vrr calculations will need to know the framestart delay value
we use. Currently we program it always to zero, but should that change
we probably want to stash it somewhere.
Could stick it into the crtc_state I suppose, but since we never
change it let's just stuff it into dev_priv for now.
v2:
* Rebase on drm-tip (Manasi)
v3:
* Framestart_delay as 1 - 4 to align with HW
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-3-manasi.d.navare@intel.com
This function sets the VRR property for connector based
on the platform support, EDID monitor range and DP sink
DPCD capability of outputing video without msa
timing information.
v8:
* Use HAS_VRR, remove drm_conn declaration (Jani N)
* Fix typos in Comment (Jani N)
v7:
* Move the helper to separate file (Manasi)
v6:
* Remove unset of prop
v5:
* Fix the vrr prop not being set in kernel (Manasi)
* Unset the prop on connector disconnect (Manasi)
v4:
* Rebase (Mansi)
v3:
* intel_dp_is_vrr_capable can be used for debugfs, make it
non static (Manasi)
v2:
* Just set this in intel_dp_get_modes instead of new hook (Jani)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-2-manasi.d.navare@intel.com
There exists many build warnings when make M=samples/bpf on the Loongson
platform, this issue is MIPS related, x86 compiles just fine.
Here are some warnings:
CC samples/bpf/ibumad_user.o
samples/bpf/ibumad_user.c: In function ‘dump_counts’:
samples/bpf/ibumad_user.c:46:24: warning: format ‘%llu’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
printf("0x%02x : %llu\n", key, value);
~~~^ ~~~~~
%lu
CC samples/bpf/offwaketime_user.o
samples/bpf/offwaketime_user.c: In function ‘print_ksym’:
samples/bpf/offwaketime_user.c:34:17: warning: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
printf("%s/%llx;", sym->name, addr);
~~~^ ~~~~
%lx
samples/bpf/offwaketime_user.c: In function ‘print_stack’:
samples/bpf/offwaketime_user.c:68:17: warning: format ‘%lld’ expects argument of type ‘long long int’, but argument 3 has type ‘__u64’ {aka ‘long unsigned int’} [-Wformat=]
printf(";%s %lld\n", key->waker, count);
~~~^ ~~~~~
%ld
MIPS needs __SANE_USERSPACE_TYPES__ before <linux/types.h> to select
'int-ll64.h' in arch/mips/include/uapi/asm/types.h, then it can avoid
build warnings when printing __u64 with %llu, %llx or %lld.
The header tools/include/linux/types.h defines __SANE_USERSPACE_TYPES__,
it seems that we can include <linux/types.h> in the source files which
have build warnings, but it has no effect due to actually it includes
usr/include/linux/types.h instead of tools/include/linux/types.h, the
problem is that "usr/include" is preferred first than "tools/include"
in samples/bpf/Makefile, that sounds like a ugly hack to -Itools/include
before -Iusr/include.
So define __SANE_USERSPACE_TYPES__ for MIPS in samples/bpf/Makefile
is proper, if add "TPROGS_CFLAGS += -D__SANE_USERSPACE_TYPES__" in
samples/bpf/Makefile, it appears the following error:
Auto-detecting system features:
... libelf: [ on ]
... zlib: [ on ]
... bpf: [ OFF ]
BPF API too old
make[3]: *** [Makefile:293: bpfdep] Error 1
make[2]: *** [Makefile:156: all] Error 2
With #ifndef __SANE_USERSPACE_TYPES__ in tools/include/linux/types.h,
the above error has gone and this ifndef change does not hurt other
compilations.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/1611551146-14052-1-git-send-email-yangtiezhu@loongson.cn
The "amba" bus nodes wrapping all the DMA-330 nodes serve no useful
purpose, and certainly bear no relation at all to the actual underlying
interconnect topology. They appear to be cargo-cult copying from a
design misstep in the very early days of FDT adoption on ARM, which was
righted with the "arm,primecell" compatible, and the last trace of the
idea finally purged by commit 2ef7d5f342 ("ARM, ARM64: dts: drop
"arm,amba-bus" in favor of "simple-bus"").
As such, they can simply be removed and the DMA-330 nodes fitted into
the normal sort order.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/e682edd25133bde2ed8198138febc90071530a51.1611186142.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Update struct bpf_perf_event_data with the addr field to match the
tools headers with the kernel headers.
Signed-off-by: Florian Lehner <dev@der-flo.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210123185221.23946-1-dev@der-flo.net
Following RFC 6554 [1], the current order of fields is wrong for big
endian definition. Indeed, here is how the header looks like:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Next Header | Hdr Ext Len | Routing Type | Segments Left |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CmprI | CmprE | Pad | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This patch reorders fields so that big endian definition is now correct.
[1] https://tools.ietf.org/html/rfc6554#section-3
Fixes: cfa933d938 ("include: uapi: linux: add rpl sr header definition")
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missed 'ranges' and 'dma-coherent' properties as cdns-usb DT nodes has
child node and DMA IO is coherent on TI K3 J721E/J7200 SoCs.
This also fixes dtbs_check warning:
cdns-usb@4104000: 'dma-coherent', 'ranges' do not match any of the regexes: '^usb@', 'pinctrl-[0-9]+'
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210115193124.5706-1-grygorii.strashko@ti.com
Signed-off-by: Rob Herring <robh@kernel.org>
NanoPi R2S is headless, so rightly does not enable any of the display
interface hardware, which currently provokes an obnoxious error in the
boot log from the fake DRM device failing to find anything to bind to.
It probably isn't *too* hard to obviate the fake device shenanigans
entirely with a bit of driver reshuffling, but for now let's just
disable it here to shut up the spurious error.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/c4553dfad1ad6792c4f22454c135ff55de77e2d6.1611186099.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Let us use a local variable in nsswitchthread(), so we can remove a
lot of casting for better readability.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210122154725.22140-7-bjorn.topel@gmail.com
Instead of passing void * all over the place, let us pass the actual
type (ifobject) and remove the void-ptr-to-type-ptr casting.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210122154725.22140-2-bjorn.topel@gmail.com
We create a new file for all VRR related helpers.
Also add a function to check vrr capability based on
platform support, DPCD bits and EDID monitor range.
v2:
* Remove author (Jani N)
* Define HAS_VRR (Jani N)
* Ensure intel_dp can be obtained from conn (Jani N)
v3:
* Fix the header indent (Manasi)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125200818.2015-1-manasi.d.navare@intel.com
The NanoPi M4B is a minor revision of the original M4.
The differences against the original Nanopi M4 that are common with the
other M4V2 revision include:
- microphone header removed
- power button added
- recovery button added
Additional changes specific to the M4B:
- USB 3.0 hub removed; board now has 2x USB 3.0 type-A ports and 2x
USB 2.0 ports
- ADB toggle switch added; this changes the top USB 3.0 host port to
a peripheral port
- Type-C port no longer supports data or PD
- WiFi/Bluetooth combo chip switched to AP6256, which supports BT 5.0
but only 1T1R (down from 2T2R) for WiFi
Add a new dts file for the new board revision that shows the difference
against the original.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210121162321.4538-5-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Only the NanoPC T4 hs the PCIe reset pin routed to the SoC. For the
NanoPi M4 family, no such signal is routed to the expansion header on
the base board.
As the schematics for the expansion board were not released, it is
unclear how this is handled, but the likely answer is that the signal
is always pulled high.
Move the ep-gpios property from the common nanopi4.dtsi file to the
board level nanopc-t4.dts file. This makes the nanopi-m4 lack ep-gpios,
matching the board design.
A companion patch "PCI: rockchip: make ep_gpio optional" for the Linux
driver is required, as the driver currently requires the property to be
present.
Fixes: e7a0959082 ("arm64: dts: rockchip: Add devicetree for NanoPC-T4")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210121162321.4538-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add detection for kernel version, and adapt the BPF program based on
kernel support. This way, users will get the best possible performance
from the BPF program.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20210122105351.11751-4-bjorn.topel@gmail.com
TPS65910 is a PMIC MFD device and RTC is one of its functions. The
wakeup-source DT property is specified for the parent MFD device and we
need to use this property for the RTC in order to allow to use RTC alarm
for waking up system from suspend by default, instead of requiring user
to enable wakeup manually via sysfs.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210120211603.18555-1-digetx@gmail.com
Fold xp_assign_dev and __xp_assign_dev. The former directly calls the
latter.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20210122105351.11751-3-bjorn.topel@gmail.com
The explicit_free parameter of the __xsk_rcv() function was used to
mark whether the call was via the generic XDP or the native XDP
path. Instead of clutter the code with if-statements and "true/false"
parameters which are hard to understand, simply move the explicit free
to the __xsk_map_redirect() which is always called from the native XDP
path.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20210122105351.11751-2-bjorn.topel@gmail.com
This fixes corrupted display output in HDMI deep color
10/12 bpc mode at least as observed on AMD Mullins, DCE-8.3.
It will hopefully also provide fixes for other DCE's up to
DCE-11, assuming those will need similar fixes, but i could
not test that for HDMI due to lack of suitable hw, so viewer
discretion is advised.
dce110_stream_encoder_hdmi_set_stream_attribute() is used for
HDMI setup on all DCE's and is missing color_depth assignment.
dce110_program_pix_clk() is used for pixel clock setup on HDMI
for DCE 6-11, and is missing color_depth assignment.
Additionally some of the underlying Atombios specific encoder
and pixelclock setup functions are missing code which is in
the classic amdgpu kms modesetting path and the in the radeon
kms driver for DCE6/DCE8.
encoder_control_digx_v3() - Was missing setup code wrt. amdgpu
and radeon kms classic drivers. Added here, but untested due to
lack of suitable test hw.
encoder_control_digx_v4() - Added missing setup code.
Successfully tested on AMD mullins / DCE-8.3 with HDMI deep color
output at 10 bpc and 12 bpc.
Note that encoder_control_digx_v5() has proper setup code in place
and is used, e.g., by DCE-11.2, but this code wasn't used for deep
color setup due to the missing cntl.color_depth setup in the calling
function for HDMI.
set_pixel_clock_v5() - Missing setup code wrt. classic amdgpu/radeon
kms. Added here, but untested due to lack of hw.
set_pixel_clock_v6() - Missing setup code added. Successfully tested
on AMD mullins DCE-8.3. This fixes corrupted display output at HDMI
deep color output with 10 bpc or 12 bpc.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In set_clamp(), the comments and definitions for the COLOR_DEPTH_101010
and COLOR_DEPTH_121212 cases directly contradict the code comment which
explains how this should work, whereas the COLOR_DEPTH_888 case
is consistent with the code comments. Comment says the bitmask should
be chosen to align to the top-most 10 or 12 MSB's on a 14 bit bus, but
the implementation contradicts that: 10 bit case sets a mask for 12 bpc
clamping, whereas 12 bit case sets a mask for 14 bpc clamping.
Note that during my limited testing on DCE-8.3 (HDMI deep color)
and DCE-11.2 (DP deep color), this didn't have any obvious ill
effects, neither did fixing it change anything obvious for the
better, so this fix may be inconsequential on DCE, and just
reduce the confusion of innocent bystanders when reading the code
and trying to investigate problems with 10 bpc+ output.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang warns about the -mhard-float command line arguments
on architectures that do not support this:
clang: error: argument unused during compilation: '-mhard-float' [-Werror,-Wunused-command-line-argument]
Move this into the gcc-specific arguments.
Fixes: e77165bf7b ("drm/amd/display: Add DCN3 blocks to Makefile")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The debug printk dereferences "link->link_enc" before we have ensured
that it is non-NULL. Fix this potential NULL derefence by moving the
printk after the check.
Fixes: 64ff088242 ("drm/amd/display: Log link/connector info provided in BIOS object table")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change the license of color_table.c to match color_table.h granting
permission to modify and distribute.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the ! operator is incorrectly being used to flip bits on
mask values. Fix this by using the bit-wise ~ operator instead.
Addresses-Coverity: ("Logical vs. bitwise operator")
Fixes: 3c9a7b7d6e ("drm/amdgpu: update mmhub mgcg&ls for mmhub_v2_3")
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
store swsmu user power configurations which include
power limit, clock frequencies, fan speed and fan mode
on suspend and reinstate on resume.
V2: Addressed Lijo's review comments
added a function to set clock interdependencies
add check on fan control mode to reapply fan speed
V3: Addressed review comments from Alex
moved store logic and reinstate function call into swSMU
V4: added a logic to keep off storing configurations in suspend
V5: Addressed review comments from Lijo
add a restore flag
give restore priority to mclk comparing fclk and socclk
Signed-off-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
when vram lost happened in guest, try to write vram can lead to
kernel stuck.
[How]
When the readback data is invalid, don't do write work, directly
reschedule a new work.
Signed-off-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Reviewed-by: Monk Liu<monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>