Call of_node_put() to decrement the reference count of the child node
child_np when jumping out of the loop body of
for_each_available_child_of_node(), which is a macro that increments and
decrements the reference count of child node. If the loop is broken, the
reference of the child node should be dropped manually.
Fixes: 5a7c81547c ("memory: ti-aemif: introduce AEMIF driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210121090359.61763-1-bianpan2016@163.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for the following Xperias:
* Z3+ [aka Z4 in some regions] (Ivy)
* Z4 Tablet (Karin)
* Z4 Tablet Wi-Fi (Karin_windy) [APQ8094]
* Z5 Compact (Suzuran)
* Z5 Premium (Satsuki)
These devices are very similar in terms of hardware, with main
differences being display panels.
While at it, update comments describing hardware used:
SMB charger seems to not be used after all, PMI8994 charger
is in use instead.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210118162432.107275-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When an already remapped bio is resubmitted (e.g. by blk_queue_split),
bio_check_eod will compare the remapped bi_sector against the size
of the partition, leading to spurious I/O failures.
Skip the EOD check in this case.
Fixes: 309dca309f ("block: store a block_device pointer in struct bio")
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
MSM8994 uses similar to MSM8996, legacy-style voltage
control, but does not include a VDD_SC_CX line.
This setup is also correct for MSM8992.
Do note that there exist some boards that use a tertiary PMIC
(most likely pm8004), where SMPB on VDDGFX becomes SMPC. I
cannot test this configuration though.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210118161943.105733-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bluetooth Core Specification v5.2, Vol. 3, Part A, section 1.4, table
1.1:
'Start Fragments always either begin with the first octet of the Basic
L2CAP header of a PDU or they have a length of zero (see [Vol 2] Part
B, Section 6.6.2).'
Apparently this was changed by the following errata:
https://www.bluetooth.org/tse/errata_view.cfm?errata_id=10216
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The standard DT property name is "interrupt-names".
Fixes: fd913ef7ce ("Bluetooth: btusb: Add out-of-band wakeup support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-----BEGIN PGP SIGNATURE-----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=pBad
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.11-urgent-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk fix from Petr Mladek:
"The fix of a potential buffer overflow in 5.11-rc5 introduced another
one. The trailing '\0' might be written up to the message "len" past
the buffer. Fortunately, it is not that easy to hit.
Most readers use 1kB buffers for a single message. Typical messages
fit into the temporary buffer with enough reserve.
Also readers do not rely on the '\0'. It is related to the previous
fix. Some readers required the space for the trailing '\0'. We decided
to write it there to avoid such regressions in the future.
The most realistic victims are dumpers using kmsg_dump_get_buffer().
They are filling the entire buffer with as many messages as possible.
They are typically used when handling panic()"
* tag 'printk-for-5.11-urgent-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: fix string termination for record_print_text()
Switch the platform code to use x86_id_table and accompanying API
instead of custom comparison against x86 CPU model.
This is one of the last users of custom API for that and following
changes will remove it for the good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Since SCU code along with the Intel MID watchdog driver has been refactored
in a way that latter will be probed only after the former has been come
to live, the notification code is bogus and not needed. Remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The ACPI-enabled Intel MID platforms neither have WDAT table nor proper IDs
to instantiate watchdog device. In order to keep them working move the board
code from arch/x86 to drivers/platform/x86.
Note, the complete SFI support is going to be removed, that's why PDx86
has been chosen as a new home for it. This is the only device which needs
additional code so far.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
When SCU is not ready and CONFIG_DEBUG_SHIRQ=y we got deferred probe followed
by fired test IRQ which immediately makes kernel panic. Fix this by delaying
IRQ handler registration till SCU is ready.
Fixes: 80ae679b8f ("watchdog: intel-mid_wdt: Convert to use new SCU IPC API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Moreover this code duplicates gpio-pxa since the IP has been derived
from XScale implementation. If anybody wants to resurrect this
it has to be part of gpio-pxa.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Since GPIOs are optional we don't need to repeat checks that are done
in the GPIO API. Remove them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Convert the GMA500 driver to use the new SCU IPC API. This allows us
to get rid of the duplicate PMC IPC implementation which is now covered
in SCU IPC driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
When setting up a device, we can krealloc the config->socks array to add
new sockets to the configuration. However if we happen to get a IO
request in at this point even though we aren't setup we could hit a UAF,
as we deref config->socks without any locking, assuming that the
configuration was setup already and that ->socks is safe to access it as
we have a reference on the configuration.
But there's nothing really preventing IO from occurring at this point of
the device setup, we don't want to incur the overhead of a lock to
access ->socks when it will never change while the device is running.
To fix this UAF scenario simply freeze the queue if we are adding
sockets. This will protect us from this particular case without adding
any additional overhead for the normal running case.
Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are two callers of acpi_get_device_data(), acpi_bus_get_device()
and acpi_bus_get_acpi_device(), but only one of them takes the int
return value into account. Moreover, the latter knows that it passes
a valid return pointer to acpi_get_device_data() and it properly
clears that pointer upfront, so it doesn't need acpi_get_device_data()
to do that.
For this reason, rearrange acpi_get_device_data() to return a strct
acpi_device pointer instead of an int and adapt its callers to that.
While at it, rename acpi_get_device_data() to handle_to_device(),
because the old name does not really reflect the functionality
provided by that function.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Add empty lines in some places in acpi_device_add() to help
readability and drop leading spaces before the labels in there.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The upfront allocation of new_bus_id is done to avoid allocating
memory under acpi_device_lock, but it doesn't really help,
because (1) it leads to many unnecessary memory allocations for
_ADR devices, (2) kstrdup_const() is run under that lock anyway and
(3) it complicates the code.
Rearrange acpi_device_add() to allocate memory for a new struct
acpi_device_bus_id instance only when necessary, eliminate a redundant
local variable from it and reduce the number of labels in there.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Flush the swap writer after, not before, marking the files, to ensure the
signature is properly written.
Fixes: 6f612af578 ("PM / Hibernate: Group swap ops")
Signed-off-by: Laurent Badel <laurentbadel@eaton.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The vendor kernel uses the following thermal-zone settings:
<= 70°C:
- CPU frequency limited to 1.488GHz
- GPU limited to 511MHz and 2 cores (pixel processors)
<= 80°C:
- CPU frequency limited to 1.2GHz
- GPU limited to 435MHz and 2 cores (pixel processors)
<= 90°C:
- CPU frequency limited to 0.804GHz
- GPU limited to 328MHz and 1 core (pixel processor)
Add simplified thermal configuration which is taken from the
GXBB/GXL/GXM SoC family (which uses the same manufacturing process and
has the same maximum junction temperature of 125°C). With this the
thermal framework will try to keep the SoC temperature at or below 80°C
which is identical to the vendor kernel (with the exception of one CPU
frequency step from 1.488GHz to 1.536GHz).
The number of GPU cores are not taken into account as this is not
supported.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-5-martin.blumenstingl@googlemail.com
The vendor kernel uses the following thermal-zone settings:
<= 70°C:
- CPU frequency limited to 1.608GHz
- GPU limited to 511MHz and 5 cores (pixel processors)
<= 80°C:
- CPU frequency limited to 1.2GHz
- GPU limited to 435MHz and 4 cores (pixel processors)
<= 90°C:
- CPU frequency limited to 0.804GHz
- GPU limited to 328MHz and 3 cores (pixel processors)
Add simplified thermal configuration which is taken from the
GXBB/GXL/GXM SoC family (which uses the same manufacturing process and
has the same maximum junction temperature of 125°C). With this the
thermal framework will try to keep the SoC temperature at or below 80°C
which is identical to the vendor kernel (with the exception of one GPU
pixel processor).
The number of GPU cores are not taken into account as this is not
supported.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-4-martin.blumenstingl@googlemail.com
The SoC temperature can be retrieved from ADC channel 8 on all 32-bit
SoCs (Meson6, Meson8, Meson8b and Meson8m2). Add a "generic-adc-thermal"
instance to meson.dtsi so the thermal sensor is available for all SoCs.
If the temperature sensor calibration data is missing for a board then
the "generic-adc-thermal" will not probe and not register a thermal
sensor.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-3-martin.blumenstingl@googlemail.com
The SoC temperature can be retrieved from ADC channel 8 on all 32-bit
SoCs (Meson6, Meson8, Meson8b and Meson8m2). Move the iio-hwmon instance
to meson.dtsi instead of duplicating it in all board.dts.
If the temperature sensor calibration data is missing for a board then
iio-hwmon will simply not probe.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-2-martin.blumenstingl@googlemail.com
32-bit Amlogic Meson platforms are using a special ADC channel to read
the SoC temperature. Enable the "generic ADC thermal" driver so this
data can be used to cool the SoC for example by reduing the maximum CPU
and GPU frequencies temporarily.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201221181306.904272-6-martin.blumenstingl@googlemail.com
After a sudden power failure we may end up with a space cache on disk that
is not valid and needs to be rebuilt from scratch.
If that happens, during log replay when we attempt to pin an extent buffer
from a log tree, at btrfs_pin_extent_for_log_replay(), we do not wait for
the space cache to be rebuilt through the call to:
btrfs_cache_block_group(cache, 1);
That is because that only waits for the task (work queue job) that loads
the space cache to change the cache state from BTRFS_CACHE_FAST to any
other value. That is ok when the space cache on disk exists and is valid,
but when the cache is not valid and needs to be rebuilt, it ends up
returning as soon as the cache state changes to BTRFS_CACHE_STARTED (done
at caching_thread()).
So this means that we can end up trying to unpin a range which is not yet
marked as free in the block group. This results in the call to
btrfs_remove_free_space() to return -EINVAL to
btrfs_pin_extent_for_log_replay(), which in turn makes the log replay fail
as well as mounting the filesystem. More specifically the -EINVAL comes
from free_space_cache.c:remove_from_bitmap(), because the requested range
is not marked as free space (ones in the bitmap), we have the following
condition triggered:
static noinline int remove_from_bitmap(struct btrfs_free_space_ctl *ctl,
(...)
if (ret < 0 || search_start != *offset)
return -EINVAL;
(...)
It's the "search_start != *offset" that results in the condition being
evaluated to true.
When this happens we got the following in dmesg/syslog:
[72383.415114] BTRFS: device fsid 32b95b69-0ea9-496a-9f02-3f5a56dc9322 devid 1 transid 1432 /dev/sdb scanned by mount (3816007)
[72383.417837] BTRFS info (device sdb): disk space caching is enabled
[72383.418536] BTRFS info (device sdb): has skinny extents
[72383.423846] BTRFS info (device sdb): start tree-log replay
[72383.426416] BTRFS warning (device sdb): block group 30408704 has wrong amount of free space
[72383.427686] BTRFS warning (device sdb): failed to load free space cache for block group 30408704, rebuilding it now
[72383.454291] BTRFS: error (device sdb) in btrfs_recover_log_trees:6203: errno=-22 unknown (Failed to pin buffers while recovering log root tree.)
[72383.456725] BTRFS: error (device sdb) in btrfs_replay_log:2253: errno=-22 unknown (Failed to recover log tree)
[72383.460241] BTRFS error (device sdb): open_ctree failed
We also mark the range for the extent buffer in the excluded extents io
tree. That is fine when the space cache is valid on disk and we can load
it, in which case it causes no problems.
However, for the case where we need to rebuild the space cache, because it
is either invalid or it is missing, having the extent buffer range marked
in the excluded extents io tree leads to a -EINVAL failure from the call
to btrfs_remove_free_space(), resulting in the log replay and mount to
fail. This is because by having the range marked in the excluded extents
io tree, the caching thread ends up never adding the range of the extent
buffer as free space in the block group since the calls to
add_new_free_space(), called from load_extent_tree_free(), filter out any
ranges that are marked as excluded extents.
So fix this by making sure that during log replay we wait for the caching
task to finish completely when we need to rebuild a space cache, and also
drop the need to mark the extent buffer range in the excluded extents io
tree, as well as clearing ranges from that tree at
btrfs_finish_extent_commit().
This started to happen with some frequency on large filesystems having
block groups with a lot of fragmentation since the recent commit
e747853cae ("btrfs: load free space cache asynchronously"), but in
fact the issue has been there for years, it was just much less likely
to happen.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This effectively reverts commit d5c8238849 ("btrfs: convert
data_seqcount to seqcount_mutex_t").
While running fstests on 32 bits test box, many tests failed because of
warnings in dmesg. One of those warnings (btrfs/003):
[66.441317] WARNING: CPU: 6 PID: 9251 at include/linux/seqlock.h:279 btrfs_remove_chunk+0x58b/0x7b0 [btrfs]
[66.441446] CPU: 6 PID: 9251 Comm: btrfs Tainted: G O 5.11.0-rc4-custom+ #5
[66.441449] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ArchLinux 1.14.0-1 04/01/2014
[66.441451] EIP: btrfs_remove_chunk+0x58b/0x7b0 [btrfs]
[66.441472] EAX: 00000000 EBX: 00000001 ECX: c576070c EDX: c6b15803
[66.441475] ESI: 10000000 EDI: 00000000 EBP: c56fbcfc ESP: c56fbc70
[66.441477] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010246
[66.441481] CR0: 80050033 CR2: 05c8da20 CR3: 04b20000 CR4: 00350ed0
[66.441485] Call Trace:
[66.441510] btrfs_relocate_chunk+0xb1/0x100 [btrfs]
[66.441529] ? btrfs_lookup_block_group+0x17/0x20 [btrfs]
[66.441562] btrfs_balance+0x8ed/0x13b0 [btrfs]
[66.441586] ? btrfs_ioctl_balance+0x333/0x3c0 [btrfs]
[66.441619] ? __this_cpu_preempt_check+0xf/0x11
[66.441643] btrfs_ioctl_balance+0x333/0x3c0 [btrfs]
[66.441664] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[66.441683] btrfs_ioctl+0x414/0x2ae0 [btrfs]
[66.441700] ? __lock_acquire+0x35f/0x2650
[66.441717] ? lockdep_hardirqs_on+0x87/0x120
[66.441720] ? lockdep_hardirqs_on_prepare+0xd0/0x1e0
[66.441724] ? call_rcu+0x2d3/0x530
[66.441731] ? __might_fault+0x41/0x90
[66.441736] ? kvm_sched_clock_read+0x15/0x50
[66.441740] ? sched_clock+0x8/0x10
[66.441745] ? sched_clock_cpu+0x13/0x180
[66.441750] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[66.441750] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[66.441768] __ia32_sys_ioctl+0x165/0x8a0
[66.441773] ? __this_cpu_preempt_check+0xf/0x11
[66.441785] ? __might_fault+0x89/0x90
[66.441791] __do_fast_syscall_32+0x54/0x80
[66.441796] do_fast_syscall_32+0x32/0x70
[66.441801] do_SYSENTER_32+0x15/0x20
[66.441805] entry_SYSENTER_32+0x9f/0xf2
[66.441808] EIP: 0xab7b5549
[66.441814] EAX: ffffffda EBX: 00000003 ECX: c4009420 EDX: bfa91f5c
[66.441816] ESI: 00000003 EDI: 00000001 EBP: 00000000 ESP: bfa91e98
[66.441818] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b EFLAGS: 00000292
[66.441833] irq event stamp: 42579
[66.441835] hardirqs last enabled at (42585): [<c60eb065>] console_unlock+0x495/0x590
[66.441838] hardirqs last disabled at (42590): [<c60eafd5>] console_unlock+0x405/0x590
[66.441840] softirqs last enabled at (41698): [<c601b76c>] call_on_stack+0x1c/0x60
[66.441843] softirqs last disabled at (41681): [<c601b76c>] call_on_stack+0x1c/0x60
========================================================================
btrfs_remove_chunk+0x58b/0x7b0:
__seqprop_mutex_assert at linux/./include/linux/seqlock.h:279
(inlined by) btrfs_device_set_bytes_used at linux/fs/btrfs/volumes.h:212
(inlined by) btrfs_remove_chunk at linux/fs/btrfs/volumes.c:2994
========================================================================
The warning is produced by lockdep_assert_held() in
__seqprop_mutex_assert() if CONFIG_LOCKDEP is enabled.
And "olumes.c:2994 is btrfs_device_set_bytes_used() with mutex lock
fs_info->chunk_mutex held already.
After adding some debug prints, the cause was found that many
__alloc_device() are called with NULL @fs_info (during scanning ioctl).
Inside the function, btrfs_device_data_ordered_init() is expanded to
seqcount_mutex_init(). In this scenario, its second
parameter info->chunk_mutex is &NULL->chunk_mutex which equals
to offsetof(struct btrfs_fs_info, chunk_mutex) unexpectedly. Thus,
seqcount_mutex_init() is called in wrong way. And later
btrfs_device_get/set helpers trigger lockdep warnings.
The device and filesystem object lifetimes are different and we'd have
to synchronize initialization of the btrfs_device::data_seqcount with
the fs_info, possibly using some additional synchronization. It would
still not prevent concurrent access to the seqcount lock when it's used
for read and initialization.
Commit d5c8238849 ("btrfs: convert data_seqcount to seqcount_mutex_t")
does not mention a particular problem being fixed so revert should not
cause any harm and we'll get the lockdep warning fixed.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=210139
Reported-by: Erhard F <erhard_f@mailbox.org>
Fixes: d5c8238849 ("btrfs: convert data_seqcount to seqcount_mutex_t")
CC: stable@vger.kernel.org # 5.10
CC: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Su Yue <l@damenly.su>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add ttyVK support to driver to allow console access to VK card from host.
Device node will be in the follow form /dev/bcm-vk.x_ttyVKy where:
x is the instance of the VK card
y is the tty device number on the VK card
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20210120175827.14820-14-scott.branden@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mmap function that allows host application to open up BAR2 memory
for remote spooling out messages from the VK logger.
Co-developed-by: Desmond Yan <desmond.yan@broadcom.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Desmond Yan <desmond.yan@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20210120175827.14820-12-scott.branden@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add reset support via ioctl.
Kill user processes that are open when VK card is reset.
If a particular PID has issued the reset request do not kill that process
as it issued the ioctl.
Co-developed-by: Desmond Yan <desmond.yan@broadcom.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Desmond Yan <desmond.yan@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20210120175827.14820-11-scott.branden@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add message support in order to be able to communicate
to VK card via message queues.
This info is used for debug purposes via collection of logs via direct
read of BAR space and by sysfs access (in a follow on commit).
Co-developed-by: Desmond Yan <desmond.yan@broadcom.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Desmond Yan <desmond.yan@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20210120175827.14820-10-scott.branden@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to get card_info (details about card),
peerlog_info (to get details of peerlog on card),
and proc_mon_info (process monitoring on card).
This info is used for collection of logs via direct
read of BAR space and by sysfs access (in a follow on commit).
Co-developed-by: Desmond Yan <desmond.yan@broadcom.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Desmond Yan <desmond.yan@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20210120175827.14820-9-scott.branden@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>