The PicoITX has only one ethernet routed out, so the KS8851 is not used
at all. Disable the KS8851 and the entire FMC controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
CHECK arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml: led-rgb: 'led-blue', 'led-green', 'led-red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The new >8k CEA modes have dotclocks reaching 5.94 GHz, which
means our clock*1000 will now overflow the 32bit unsigned
integer. Switch to 64bit maths to avoid it.
Cc: stable@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201022194256.30978-1-ville.syrjala@linux.intel.com
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
We can get the following in the logs every few minutes or so:
wlcore: ERROR exceeded max RX BA sessions
Let's downgrade the message to a debug message as suggested by the TI
support folks at:
https://e2e.ti.com/support/wireless-connectivity/wifi/f/968/p/352435/1244754
"The WL127x firmware supports max of 3 BA sessions. It cannot be increased.
I think the problem here is the peer trying to initiate a 4th BA session
(ADDBA request)."
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210101065955.63386-1-tony@atomide.com
This ensure that previous association attempts do not leave stale statuses
on subsequent attempts.
This fixes the WARN_ON(!cr->bss)) from __cfg80211_connect_result() when
connecting to an AP after a previous connection failure (e.g. where EAP fails
due to incorrect psk but association succeeded). In some scenarios, indeed,
brcmf_is_linkup() was reporting a link up event too early due to stale
BRCMF_VIF_STATUS_ASSOC_SUCCESS bit, thus reporting to cfg80211 a connection
result with a zeroed bssid (vif->profile.bssid is still empty), causing the
WARN_ON due to the call to cfg80211_get_bss() with the empty bssid.
Signed-off-by: Luca Pesce <luca.pesce@vimar.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608807119-21785-1-git-send-email-luca.pesce@vimar.com
A null pointer will be passed to a kfree() call after a kzalloc() call failed.
This code is useless. Thus delete the extra function call.
A goto statement is also no longer needed. Thus adjust an if branch.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201222135113.20680-1-zhengyongjun3@huawei.com
When the usb device being plugged out, before ieee80211 gets to know the
hw being removed, it gets to know that the association status changed,
and thus ask for the device to do the calibration. This causes error as
the hw is absent.
This can be avoid by checking the status of the device before sending
the calibration request to the device.
Signed-off-by: Zhi Han <z.han@gmx.net>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201217161657.GB12562@E480
When the usb device being plugged out, before the usb_driver:disconnect
called by e.g workqueue, it is possible that some URBs are still in
processing, and being marked as EPROTO in host controller.
Those URBs should not be scheduled in complete_rx callback function to
get further processing.
Signed-off-by: Zhi Han <z.han@gmx.net>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201217161302.GA12562@E480
This adds support for the BCM43666/4 which seems to be using the same
firmware as BCM4366 (4366c0). I found it in the Netgear R8000P router.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201214101553.32097-1-zajec5@gmail.com
As the Marvell PCIE WiFi-Ex driver does not have any code or data
located in initmem, there is no need to annotate the mwifiex_pcie
structure with __refdata. Drop the annotation, to avoid suppressing
future section warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201211133835.2970384-1-geert+renesas@glider.be
Fix the following coccicheck warning:
./drivers/net/wireless/realtek/rtw88/debug.c:800:17-23: WARNING:
Comparison of 0/1 to bool variable
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1610445040-23599-1-git-send-email-abaci-bugfix@linux.alibaba.com
To protect both of WL/BT performance while BT is under re-link state.
4-slot mode TDMA can make the re-link more sensitive and mitigate the WL
throughput drop.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210112021135.3823-1-pkshih@realtek.com
Hal function must follow the value that calculates from dynamic mechanism.
Force to set new_lvl to 4 damages receiving ability. System will not able
to reconnect to the AP if wifi unexpected disconnecting at this moment.
Signed-off-by: Vincent Fann <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201228082516.16488-1-pkshih@realtek.com
Sometimes driver does not get tx report from firmware because wifi
environment is too noisy to get ack from AP about a TX frame,
or firmware is too busy to report driver in a estimated time.
But the condition will not affect wifi function or throughput.
So we reduce the log level to rtw_debug instead of scary backtrace.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201228082433.16431-1-pkshih@realtek.com
The parameter of kfree function is NULL, so kfree code is useless, delete it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201216130442.13869-1-zhengyongjun3@huawei.com
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Fixes: fde180f06d ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Fixes: ac68793f49 ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
Fixes: ac68793f49 ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
We can't be setting the display_id register to an invalid value
because that makes our device reset the fb which causes nasty
flicker (due to destruction and creation of a new fb).
Also we can't be using the BITS_PER_PIXEL register if the
8BIT_EMULATION is not supported.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Link: https://patchwork.freedesktop.org/patch/414041/?series=85516&rev=2
Lets try to cleanup the usage of the term FIFO which we used for
both our MMIO based cmd queue processing and for general
command processing which could have been using command buffers
interface. We're going to rename the functions which are processing
commands (and work either via MMIO or command buffers) as _cmd_
and functions which operate on the MMIO based commands as FIFO
to match the SVGA device naming.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/414044/?series=85516&rev=2
Throttling was used before fencing to implement early vsync
support in the xorg state tracker a long time ago. The xorg
state tracker has been removed years ago and no one else
has ever used throttling. It's time to remove this code,
it hasn't been used or tested in years.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Link: https://patchwork.freedesktop.org/patch/414042/?series=85516&rev=2
Instead of doing it in multiple spots lets centralize the code
to handle pci resources. This also cleans up the error
handling a bit and will make it a lot easier to add additional
svga versions to the driver.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Link: https://patchwork.freedesktop.org/patch/414040/?series=85516&rev=2
Going forward the svga device might reuse mmio for general
register accesses, in order to prepare for that we need to
cleanup our naming and handling of fifo specific mmio reads
and writes. As part of this work lets switch to managed
mapping of the fifo mmio to make the error handling cleaner.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Link: https://patchwork.freedesktop.org/patch/414045/?series=85516&rev=2
To cleanup some of the error handling and prepare for some
other work lets switch to a managed drm device. It will
let us get a better handle on some of the error paths.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Link: https://patchwork.freedesktop.org/patch/414039/?series=85516&rev=2
Before drm got helpers for removing conflicting pci framebuffer devices
we implemented something known as "stealth" mode which allowed vmwgfx
to run even if it couldn't reserve pci resources. We can just switch
to regular drm helpers instead of keeping the stealth mode alive as
it makes our code a lot cleaner.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Link: https://patchwork.freedesktop.org/patch/414043/?series=85516&rev=2
Commit fa41d10589 ("fpga: dfl-pci: locate DFLs by PCIe vendor specific
capability") provides documentation to the FPGA Device Feature List (DFL)
Framework Overview, but introduced new documentation warnings:
./Documentation/fpga/dfl.rst:
505: WARNING: Title underline too short.
523: WARNING: Unexpected indentation.
523: WARNING: Blank line required after table.
524: WARNING: Block quote ends without a blank line; unexpected unindent.
Rectify ReST formatting in ./Documentation/fpga/dfl.rst.
Tested-by: Tom Rix <trix@redhat.com>
Acked-by: Moritz Fischer <mdf@kernel.org>
Acked-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210111112113.27242-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In default_roce_mode_store(), we took a reference to cma_dev, but didn't
return it with cma_dev_put in the error flow.
Fixes: 1c15b4f2a4 ("RDMA/core: Modify enum ib_gid_type and enum rdma_network_type")
Link: https://lore.kernel.org/r/20210113130214.562108-1-leon@kernel.org
Signed-off-by: Neta Ostrovsky <netao@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
If the allocation of the fast path blue flame register fails, the driver
should free the regular blue flame register allocated a statement above,
not the one that it just failed to allocate.
Fixes: 16c1975f10 ("IB/mlx5: Create profile infrastructure to add and remove stages")
Link: https://lore.kernel.org/r/20210113121703.559778-6-leon@kernel.org
Reported-by: Hans Petter Selasky <hanss@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
rounddown_pow_of_two() is undefined when the input is 0. Therefore we need
to avoid it in ib_umem_find_best_pgsz and return 0. Otherwise, it could
result in not rejecting an invalid page size which eventually causes a
kernel oops due to the logical inconsistency.
Fixes: 3361c29e92 ("RDMA/umem: Use simpler logic for ib_umem_find_best_pgsz()")
Link: https://lore.kernel.org/r/20210113121703.559778-2-leon@kernel.org
Signed-off-by: Aharon Landau <aharonl@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Clang warns in both mt7615 and mt7915:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:271:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_FWDL;
~ ^~~~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:278:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_WA;
~ ^~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:282:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
txq = MT_MCUQ_WM;
~ ^~~~~~~~~~
3 warnings generated.
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:238:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
qid = MT_MCUQ_WM;
~ ^~~~~~~~~~
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:240:9: warning: implicit
conversion from enumeration type 'enum mt76_mcuq_id' to different
enumeration type 'enum mt76_txq_id' [-Wenum-conversion]
qid = MT_MCUQ_FWDL;
~ ^~~~~~~~~~~~
2 warnings generated.
Use the proper type for the queue ID variables to fix these warnings.
Additionally, rename the txq variable in mt7915_mcu_send_message to be
more neutral like mt7615_mcu_send_message.
Fixes: e637763b60 ("mt76: move mcu queues to mt76_dev q_mcu array")
Link: https://github.com/ClangBuiltLinux/linux/issues/1229
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201229211548.1348077-1-natechancellor@gmail.com
DYNAMIC_FTRACE_WITH_REGS uses -fpatchable-function-entry, which makes
running recordmcount unnecessary as there are no mcount calls in object
files, and __mcount_loc doesn't need to be generated.
While there's normally no harm in running recordmcount even when it's
not strictly needed, this won't work with LTO as we have LLVM bitcode
instead of ELF objects.
This change selects FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY, which
disables recordmcount when patchable function entries are used instead.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-16-samitolvanen@google.com
Disable LTO for the vDSO by filtering out CC_FLAGS_LTO, as there's no
point in using link-time optimization for the small amount of C code.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-15-samitolvanen@google.com
Disable LTO for rodata.o to allow objcopy to be used to
manipulate sections.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-14-samitolvanen@google.com
With CONFIG_LTO_CLANG, we produce LLVM bitcode instead of ELF object
files. Since LTO is not really needed here and the Makefile assumes we
produce an object file, disable LTO for libstub.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-13-samitolvanen@google.com
With CONFIG_LTO_CLANG, clang generates LLVM IR instead of ELF object
files. As empty.o is used for probing target properties, disable LTO
for it to produce an object file instead.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-12-samitolvanen@google.com
With LTO, everything is compiled into LLVM bitcode, so we have to link
each module into native code before modpost. Kbuild uses the .lto.o
suffix for these files, which also ends up in module information. This
change strips the unnecessary .lto suffix from the module name.
Suggested-by: Bill Wendling <morbo@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-11-samitolvanen@google.com
With Clang's Link Time Optimization (LTO), the compiler can rename
static functions to avoid global naming collisions. As PCI fixup
functions are typically static, renaming can break references
to them in inline assembly. This change adds a global stub to
DECLARE_PCI_FIXUP_SECTION to fix the issue when PREL32 relocations
are used.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-10-samitolvanen@google.com
With LTO, the compiler can rename static functions to avoid global
naming collisions. As initcall functions are typically static,
renaming can break references to them in inline assembly. This
change adds a global stub with a stable name for each initcall to
fix the issue when PREL32 relocations are used.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-9-samitolvanen@google.com
With LTO, the compiler doesn't necessarily obey the link order for
initcalls, and initcall variables need globally unique names to avoid
collisions at link time.
This change exports __KBUILD_MODNAME and adds the initcall_id() macro,
which uses it together with __COUNTER__ and __LINE__ to help ensure
these variables have unique names, and moves each variable to its own
section when LTO is enabled, so the correct order can be specified using
a linker script.
The generate_initcall_ordering.pl script uses nm to find initcalls from
the object files passed to the linker, and generates a linker script
that specifies the same order for initcalls that we would have without
LTO. With LTO enabled, the script is called in link-vmlinux.sh through
jobserver-exec to limit the number of jobs spawned.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-8-samitolvanen@google.com