On MT8365, the SET/CLR of the mode is broken and some pin modes won't
be set correctly.
Use the mt8365_set_clr_mode() callback to fix the issue.
Co-developed-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Link: https://lore.kernel.org/r/20221021084708.1109986-3-bchihi@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On MT8365, the SET/CLR of the mode is broken and some pin modes won't
be set correctly.
Add mt8365_set_clr_mode() callback for such SoCs, so that instead of
using the SET/CLR register, use the main R/W register to
read/update/write the modes.
Co-developed-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Link: https://lore.kernel.org/r/20221021084708.1109986-2-bchihi@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mux routes are incomplete for the PX30. This was discovered because
we had a HW design using cif-clkoutm1 with the correct pinmux in the
Device Tree but the clock would still not work.
There are actually two muxing required: the pin muxing (performed by the
usual Device Tree pinctrl nodes) and the "function" muxing (m0 vs m1;
performed by the mux routing inside the driver). The pin muxing was
correct but the function muxing was not.
This adds the missing pins and their configuration for the mux routes
that are already specified in the driver.
Note that there are some "conflicts": it is possible *in Device Tree* to
(attempt to) mux the pins for e.g. clkoutm1 and clkinm0 at the same time
but this is actually not possible in hardware (because both share the
same bit for the function muxing). Since it is an impossible hardware
design, it is not deemed necessary to prevent the user from attempting
to "misconfigure" the pins/functions.
Fixes: 87065ca9b8 ("pinctrl: rockchip: Add pinctrl support for PX30")
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20221017-upstream-px30-cif-clkoutm1-v1-0-4ea1389237f7@theobroma-systems.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix reference to CMU_FSYS1 mmc card clock to gout clock instead of dout.
"gout" is output of a gate clock. Unlike any other clocks, the fsys1
mmc top clock does not have a divider, so it should be "mout -> gout"
instead of "mout -> gout -> dout".
This fixes make dtbs_check warning as shown below:
arch/arm64/boot/dts/exynos/exynosautov9-sadk.dtb: clock-controller@17040000:
clock-names:2: 'dout_clkcmu_fsys1_mmc_card' was expected
Fixes: 4b6ec8d886 ("dt-bindings: clock: exynosautov9: add schema for cmu_fsys0/1")
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Inbaraj E <inbaraj.e@samsung.com>
Link: https://lore.kernel.org/r/20221107124337.114135-1-inbaraj.e@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Remove the description of @required_features in elevator_match()
to clear the below warning:
block/elevator.c:103: warning: Excess function parameter 'required_features' description in 'elevator_match'
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2734
Fixes: ffb86425ee ("block: don't check for required features in elevator_match")
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221107062255.2685-1-yang.lee@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
arch-y and tune-y used lazy evaluation since they used to contain
cc-option checks. They don't any longer, so just eagerly evaluate these
command line flags.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
If the system PM callbacks haven't been assigned, the PM core falls back to
invoke the corresponding the pm_generic_* helpers for the device. Let's
rely on this behaviour and drop the redundant assignments.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Currently the regular CPU shutdown path for ARM disables IRQs/FIQs
in the secondary CPUs - smp_send_stop() calls ipi_cpu_stop(), which
is responsible for that. IRQs are architecturally masked when we
take an interrupt, but FIQs are high priority than IRQs, hence they
aren't masked. With that said, it makes sense to disable FIQs here,
but there's no need for (re-)disabling IRQs.
More than that: there is an alternative path for disabling CPUs,
in the form of function crash_smp_send_stop(), which is used for
kexec/panic path. This function relies on a SMP call that also
triggers a busy-wait loop [at machine_crash_nonpanic_core()], but
without disabling FIQs. This might lead to odd scenarios, like
early interrupts in the boot of kexec'd kernel or even interrupts
in secondary "disabled" CPUs while the main one still works in the
panic path and assumes all secondary CPUs are (really!) off.
So, let's disable FIQs in both paths and *not* disable IRQs a second
time, since they are already masked in both paths by the architecture.
This way, we keep both CPU quiesce paths consistent and safe.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
clang-15's ability to elide loops completely became more aggressive when
it can deduce how a variable is being updated in a loop. Counting down
one variable by an increment of another can be replaced by a modulo
operation.
For 64b variables on 32b ARM EABI targets, this can result in the
compiler generating calls to __aeabi_uldivmod, which it does for a do
while loop in float64_rem().
For the kernel, we'd generally prefer that developers not open code 64b
division via binary / operators and instead use the more explicit
helpers from div64.h. On arm-linux-gnuabi targets, failure to do so can
result in linkage failures due to undefined references to
__aeabi_uldivmod().
While developers can avoid open coding divisions on 64b variables, the
compiler doesn't know that the Linux kernel has a partial implementation
of a compiler runtime (--rtlib) to enforce this convention.
It's also undecidable for the compiler whether the code in question
would be faster to execute the loop vs elide it and do the 64b division.
While I actively avoid using the internal -mllvm command line flags, I
think we get better code than using barrier() here, which will force
reloads+spills in the loop for all toolchains.
Link: https://github.com/ClangBuiltLinux/linux/issues/1666
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
UEFI runtime page tables dump only for ARM64 at present,
but ARM support EFI and ARM_PTDUMP_DEBUGFS now. Since
ARM could potentially execute with a 1G/3G user/kernel
split, choosing 1G as the upper limit for UEFI runtime
end, with this, we could enable UEFI runtime page tables
on ARM.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
If there is a kernel fault, see do_kernel_fault(), we only print
the generic "paging request" or "NULL pointer dereference" message
which don't show read, write or excute information, let's provide
better fault message for them.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
To enable UBSAN on ARM, this patch enables ARCH_HAS_UBSAN_SANITIZE_ALL
from arm confiuration. Basic kernel bootup test is passed on arm with
CONFIG_UBSAN_SANITIZE_ALL enabled.
[florian: rebased against v6.0-rc7]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
"unwind: Index not found eef26358" warnings keep popping up on
CONFIG_ARM_MODULE_PLTS-enabled systems if the PC points to a PLT veneer.
Teach the unwinder how to deal with them, taking into account they don't
change state of the stack or register file except loading PC.
Link: https://lore.kernel.org/linux-arm-kernel/20200402153845.30985-1-kursad.oney@broadcom.com/
Tested-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Actually in no-MMU SoCs(i.e. i.MXRT) ZERO_PAGE(vaddr) expands to
```
virt_to_page(0)
```
that in order expands to:
```
pfn_to_page(virt_to_pfn(0))
```
and then virt_to_pfn(0) to:
```
((((unsigned long)(0) - PAGE_OFFSET) >> PAGE_SHIFT) +
PHYS_PFN_OFFSET)
```
where PAGE_OFFSET and PHYS_PFN_OFFSET are the DRAM offset(0x80000000) and
PAGE_SHIFT is 12. This way we obtain 16MB(0x01000000) summed to the base of
DRAM(0x80000000).
When ZERO_PAGE(0) is then used, for example in bio_add_page(), the page
gets an address that is out of DRAM bounds.
So instead of using fake virtual page 0 let's allocate a dedicated
zero_page during paging_init() and assign it to a global 'struct page *
empty_zero_page' the same way mmu.c does and it's the same approach used
in m68k with commit dc068f4621 as discussed here[0]. Then let's move
ZERO_PAGE() definition to the top of pgtable.h to be in common between
mmu.c and nommu.c.
[0]: https://lore.kernel.org/linux-m68k/2a462b23-5b8e-bbf4-ec7d-778434a3b9d7@google.com/T/#m1266ceb63
ad140743174d6b3070364d3c9a5179b
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
ARM Performance Monitoring Unit Table describes the properties of PMU
support in ARM-based system. The APMT table contains a list of nodes,
each represents a PMU in the system that conforms to ARM CoreSight PMU
architecture. The properties of each node include information required
to access the PMU (e.g. MMIO base address, interrupt number) and also
identification. For more detailed information, please refer to the
specification below:
* APMT: https://developer.arm.com/documentation/den0117/latest
* ARM Coresight PMU:
https://developer.arm.com/documentation/ihi0091/latest
The initial support adds the detection of APMT table and generic
infrastructure to create platform devices for ARM CoreSight PMUs.
Similar to IORT the root pointer of APMT is preserved during runtime
and each PMU platform device is given a pointer to the corresponding
APMT node.
Signed-off-by: Besar Wicaksono <bwicaksono@nvidia.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20220929002834.32664-1-bwicaksono@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
The data received via iccmax stream is not used anywhere, so no need to
allocate a big DMA buffer for it. This is especially important as the
allocation is done even in cases where reload of the firmware is skipped
and execution happens directly from the firmware stored in IMR.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221107072621.28904-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During system suspend there is a chance that the running stream undergo
an xrun and instead of the expected SNDRV_PCM_TRIGGER_SUSPEND trigger
we will receive SNDRV_PCM_TRIGGER_STOP.
The handling of SUSPEND and STOP triggers differ that case of the later
the sof_pcm_stream_free() will be called with free_widget_list = false.
But we must make sure that all active widgets and streams are free before
entering suspend in order to be able to resume without error.
We can utilize the tear_down_all_pipelines to put the system to an expected
state and to fix the suspend/resume error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221107084158.26629-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221104212409.603970-2-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221104212409.603970-1-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With all users utilizing component->set_jack(), there is no need to
export da7219_aad_jack_det() function.
While at it, remove exports from all other functions as well.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221031160227.2352630-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec driver for da7219 implements jack detect functionality, but does
not integrate it with the framework. Platform component drivers are
accessing the functionality through internal da7219_aad_jack_det()
instead.
Address this by implementing set_jack() for the codec.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221031160227.2352630-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add get/put queue id helper to manage queue id in route
setup and route free.
The queue allocation rules are:
- If widget only has one sink/source pin, zero will be
returned as the queue ID directly.
- If widget has more than one sink/source pins, and pin
binding array is defined in topology, queue ID will be
allocated according to the pin binding array.
- If widget has more than one sink/sink pins, and pin
binding array is not defined, Linux ID allocation will be
used to allocate queue ID dynamically.
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Suggested-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221107085706.2550-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for parsing sink/source pin binding array
per widget from topology. The pin binding arrays will
be used to determine the source and sink queue IDs during
widget binding for widget that requires special pin binding.
An example of widget that requires special pin binding is
the smart amplifier widget, its feedback sink pin has to be
connected to a capture DAI copier for codec feedback, while
the other sink pin has to be connected to a host DAI copier.
Pin ID is required during widget binding for correct route setup.
Conversely, the pin ID for 'generic' pins is not defined in the
topology and will be allocated by the kernel dynamically. When
only one pin is supported, the pin ID shall always be zero. When
more than one pin is supported, the pin ID is determined with the
ID allocation mechanism in the kernel.
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Suggested-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221107085706.2550-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for parsing the number of sink/source pins
per widget from topology. They will be used to determine
the sink/source queue IDs during widget binding.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Suggested-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221107085706.2550-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM connection on Card2, its DT looks like below.
Current Card2 is checking (a)/(b) part only for convert-xxx settings.
But it is not useful. This patch enables its settings at (A)/(B) part
too. (A)/(B) settings will be overwritten (a)/(b) settings if it has.
<Image> (A) (a)
Card2 <--+--> FE <---> CPU
|
+--> BE <---> Codec
(B) (b)
<DT>
card2-sound {
...
links = <fe, be>; /* (A) (B) */
};
dpcm {
/* FE */
ports@0 {
/* (A) */
fe: port { fe_ep: endpoint { remote-endpoint = <&cpu_ep>; } };
};
/* BE */
ports@1 {
/* (B) */
be: port {
convert-rate = <44100>; /* This patch enables this */
be_ep: endpoint { remote-endpoint = <&codec_ep>; }
};
};
};
cpu {
/* CPU (a) */
port { cpu_ep: endpoint { remote-endpoint = <&fe_ep>; } };
};
codec {
/* Codec (b) */
port {
convert-rate = <48000>; /* (B) settings will be over written here */
codec_ep: endpoint { remote-endpoint = <&be_ep>; }
};
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871qqn8fst.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card2-custom-sample.dtsi is assuming that
DPCM sample is MIXer connection.
FE BE
****
CPU3 -- * * -- Codec3
CPU4 -- * *
****
CPU3/CPU4 need to convert rate in this case.
This patch adds missing "convert-rate" setting sample for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8735b38fta.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No one is using asoc_simple_convert_fixup(), we don't need to
export its symbol. This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874jvj8ftp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Speaker GPIO needs to be turned on slightly behind the codec turned on.
It also need to be turned off slightly before the codec turned down.
Current code uses delay in DAPM_EVENT to do it but the mdelay delays the
DAPM itself and thus has no effect. A delayed_work is added to turn on the
speaker.
The Speaker is turned off in .trigger since trigger is called slightly
before the DAPM events.
Signed-off-by: Zhu Ning <zhuning@everest-semi.com>
------------
v1: cancel delayed work while disabling speaker.
Link: https://lore.kernel.org/r/20221028020456.90286-1-zhuning0077@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the return value check before attempting to assign the core ID to the
swidget since we are going to fail the sof_widget_ready() and free up
swidget anyways.
Fixes: 909dadf21a ("ASoC: SOF: topology: Make DAI widget parsing IPC agnostic")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221107090433.5146-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Foxconn T99W175 modem has an HP variant, which has
the following output from lspci:
01:00.0 Wireless controller [0d40]: Device 03f0:0a6c
It also has some HP-specific serial numbers on the
metal case. It works well with this driver, so add
support for this to the pci_generic driver.
Signed-off-by: Song Fuchang <song.fc@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
[mani: manually applied the patch]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
snd_soc_util_exit() is called in __init snd_soc_init() for cleanup.
Remove the __exit annotation for it to fix the build warning:
WARNING: modpost: sound/soc/snd-soc-core.o: section mismatch in reference: init_module (section: .init.text) -> snd_soc_util_exit (section: .exit.text)
Fixes: 6ec27c5388 ("ASoC: core: Fix use-after-free in snd_soc_exit()")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221031134031.256511-1-chenzhongjin@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If we're doing device replace on a zoned filesystem and discover in
scrub_enumerate_chunks() that we don't have to copy the block group it is
unlocked before it gets skipped.
But as the block group hasn't yet been locked before it leads to a locking
imbalance. To fix this simply remove the unlock.
This was uncovered by fstests' testcase btrfs/163.
Fixes: 9283b9e09a ("btrfs: remove lock protection for BLOCK_GROUP_FLAG_TO_COPY")
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When performing seeding on a zoned filesystem it is necessary to
initialize each zoned device's btrfs_zoned_device_info structure,
otherwise mounting the filesystem will cause a NULL pointer dereference.
This was uncovered by fstests' testcase btrfs/163.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When cloning a btrfs_device, we're not cloning the associated
btrfs_zoned_device_info structure of the device in case of a zoned
filesystem.
Later on this leads to a NULL pointer dereference when accessing the
device's zone_info for instance when setting a zone as active.
This was uncovered by fstests' testcase btrfs/161.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This reverts commit 786672e9e1.
[BUG]
Since commit 786672e9e1 ("btrfs: scrub: use larger block size for data
extent scrub"), btrfs scrub no longer reports errors if the corruption
is not in the first sector of a STRIPE_LEN.
The following script can expose the problem:
mkfs.btrfs -f $dev
mount $dev $mnt
xfs_io -f -c "pwrite -S 0xff 0 8k" $mnt/foobar
umount $mnt
# 13631488 is the logical bytenr of above 8K extent
btrfs-map-logical -l 13631488 -b 4096 $dev
mirror 1 logical 13631488 physical 13631488 device /dev/test/scratch1
# Corrupt the 2nd sector of that extent
xfs_io -f -c "pwrite -S 0x00 13635584 4k" $dev
mount $dev $mnt
btrfs scrub start -B $mnt
scrub done for 54e63f9f-0c30-4c84-a33b-5c56014629b7
Scrub started: Mon Nov 7 07:18:27 2022
Status: finished
Duration: 0:00:00
Total to scrub: 536.00MiB
Rate: 0.00B/s
Error summary: no errors found <<<
[CAUSE]
That offending commit enlarges the data extent scrub size from sector
size to BTRFS_STRIPE_LEN, to avoid extra scrub_block to be allocated.
But unfortunately the data extent scrub is still heavily relying on the
fact that there is only one scrub_sector per scrub_block.
Thus it will only check the first sector, and ignoring the remaining
sectors.
Furthermore the error reporting is not able to handle multiple sectors
either.
[FIX]
For now just revert the offending commit.
The consequence is just extra memory usage during scrub.
We will need a proper change to make the remaining data scrub path to
handle multiple sectors before we enlarging the data scrub size.
Reported-by: Li Zhang <zhanglikernel@gmail.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add ENOMEM among the error codes that don't print stack trace on
transaction abort. We've got several reports from syzbot that detects
stacks as errors but caused by limiting memory. As this is an artificial
condition we don't need to know where exactly the error happens, the
abort and error cleanup will continue like e.g. for EIO.
As the transaction aborts code needs to be inline in a lot of code, the
implementation cases about minimal bloat. The error codes are in a
separate function and the WARN uses the condition directly. This
increases the code size by 571 bytes on release build.
Alternatives considered: add -ENOMEM among the errors, this increases
size by 2340 bytes, various attempts to combine the WARN and helper
calls, increase by 700 or more bytes.
Example syzbot reports (error -12):
- https://syzkaller.appspot.com/bug?extid=5244d35be7f589cf093e
- https://syzkaller.appspot.com/bug?extid=9c37714c07194d816417
Signed-off-by: David Sterba <dsterba@suse.com>
swiotlb passes virtual addresses to set_memory_encrypted() and
set_memory_decrypted(), but uv_remove_shared() and uv_set_shared()
expect physical addresses. This currently works, because virtual
and physical addresses are the same.
Add virt_to_phys() to resolve the virtual-physical confusion.
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Link: https://lore.kernel.org/r/20221107121221.156274-2-nrb@linux.ibm.com
Message-Id: <20221107121221.156274-2-nrb@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
The btrfs_alloc_dummy_root() uses ERR_PTR as the error return value
rather than NULL, if error happened, there will be a NULL pointer
dereference:
BUG: KASAN: null-ptr-deref in btrfs_free_dummy_root+0x21/0x50 [btrfs]
Read of size 8 at addr 000000000000002c by task insmod/258926
CPU: 2 PID: 258926 Comm: insmod Tainted: G W 6.1.0-rc2+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
kasan_report+0xb7/0x140
kasan_check_range+0x145/0x1a0
btrfs_free_dummy_root+0x21/0x50 [btrfs]
btrfs_test_free_space_cache+0x1a8c/0x1add [btrfs]
btrfs_run_sanity_tests+0x65/0x80 [btrfs]
init_btrfs_fs+0xec/0x154 [btrfs]
do_one_initcall+0x87/0x2a0
do_init_module+0xdf/0x320
load_module+0x3006/0x3390
__do_sys_finit_module+0x113/0x1b0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: aaedb55bc0 ("Btrfs: add tests for btrfs_get_extent")
CC: stable@vger.kernel.org # 4.9+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
syzkaller found a failed assertion:
assertion failed: (args->devid != (u64)-1) || args->missing, in fs/btrfs/volumes.c:6921
This can be triggered when we set devid to (u64)-1 by ioctl. In this
case, the match of devid will be skipped and the match of device may
succeed incorrectly.
Patch 562d7b1512 introduced this function which is used to match device.
This function contains two matching scenarios, we can distinguish them by
checking the value of args->missing rather than check whether args->devid
and args->uuid is default value.
Reported-by: syzbot+031687116258450f9853@syzkaller.appspotmail.com
Fixes: 562d7b1512 ("btrfs: handle device lookup with btrfs_dev_lookup_args")
CC: stable@vger.kernel.org # 5.16+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The conversion looks harmless, however the addr value is updated inside
the loop with the previous vm_end, which then incorrectly leads to
for_each_vma_range() iterating over stuff outside the range we care
about. Fix this by storing the end value separately. Also fix the case
where the range doesn't intersect with any vma, or if the vma itself
doesn't extend the entire range, which must mean we have hole at the
end. Both should result in an error, as per the previous behaviour.
v2: Fix the cases where the range is empty, or if there's a hole at
the end of the range
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7247
Testcase: igt@gem_userptr_blits@probe
Fixes: f683b9d613 ("i915: use the VMA iterator")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Liam R. Howlett <Liam.Howlett@Oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yu Zhao <yuzhao@google.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221028130635.465839-1-matthew.auld@intel.com
(cherry picked from commit 6f7de35b50)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Currently on DG1, which does not have LLC, we hit the below
warning while rebinding an userptr invalidated object.
WARNING: CPU: 4 PID: 13008 at drivers/gpu/drm/i915/gem/i915_gem_pages.c:34 __i915_gem_object_set_pages+0x296/0x2d0 [i915]
...
RIP: 0010:__i915_gem_object_set_pages+0x296/0x2d0 [i915]
...
Call Trace:
<TASK>
i915_gem_userptr_get_pages+0x175/0x1a0 [i915]
____i915_gem_object_get_pages+0x32/0xb0 [i915]
i915_gem_object_userptr_submit_init+0x286/0x470 [i915]
eb_lookup_vmas+0x2ff/0xcf0 [i915]
? __intel_wakeref_get_first+0x55/0xb0 [i915]
i915_gem_do_execbuffer+0x785/0x21d0 [i915]
i915_gem_execbuffer2_ioctl+0xe7/0x3d0 [i915]
We shouldn't be setting the obj->cache_dirty for DGFX,
fix it.
Fixes: d70af57944 ("drm/i915/shmem: ensure flush during swap-in on non-LLC")
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Reported-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102051416.27327-1-niranjana.vishwanathapura@intel.com
(cherry picked from commit 0aeec60c76)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Currently we are observing mouse cursor stuttering when using
xrandr --scaling=1.2x1.2. X scaling/transformation seems to be
doing fronbuffer rendering. When moving mouse cursor X seems to
perform several invalidates and only one DirtyFB. I.e. it seems
to be assuming updates are sent to panel while drawing is done.
Earlier we were disabling PSR in frontbuffer invalidate call back
(when drawing in X started). PSR was re-enabled in frontbuffer
flush callback (dirtyfb ioctl). This was working fine with X
scaling/transformation. Now we are just enabling continuous full
frame (cff) in PSR invalidate callback. Enabling cff doesn't
trigger any updates. It just configures PSR to send full frame
when updates are sent. I.e. there are no updates on screen before
PSR flush callback is made. X seems to be doing several updates
in frontbuffer before doing dirtyfb ioctl.
Fix this by sending single update on every invalidate callback.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: 805f04d42a ("drm/i915/display/psr: Use continuos full frame to handle frontbuffer invalidations")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6679
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reported-by: Brian J. Tarricone <brian@tarricone.org>
Tested-by: Brian J. Tarricone <brian@tarricone.org>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221024054649.31299-1-jouni.hogander@intel.com
(cherry picked from commit d755f89220)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
