If setsockopt with option name of TCP_REPAIR_OPTIONS and opt_code
of TCPOPT_SACK_PERM is called to enable sack after data is sent
and dupacks are received , it will trigger a warning in function
tcp_verify_left_out() as follows:
============================================
WARNING: CPU: 8 PID: 0 at net/ipv4/tcp_input.c:2132
tcp_timeout_mark_lost+0x154/0x160
tcp_enter_loss+0x2b/0x290
tcp_retransmit_timer+0x50b/0x640
tcp_write_timer_handler+0x1c8/0x340
tcp_write_timer+0xe5/0x140
call_timer_fn+0x3a/0x1b0
__run_timers.part.0+0x1bf/0x2d0
run_timer_softirq+0x43/0xb0
__do_softirq+0xfd/0x373
__irq_exit_rcu+0xf6/0x140
The warning is caused in the following steps:
1. a socket named socketA is created
2. socketA enters repair mode without build a connection
3. socketA calls connect() and its state is changed to TCP_ESTABLISHED
directly
4. socketA leaves repair mode
5. socketA calls sendmsg() to send data, packets_out and sack_outs(dup
ack receives) increase
6. socketA enters repair mode again
7. socketA calls setsockopt with TCPOPT_SACK_PERM to enable sack
8. retransmit timer expires, it calls tcp_timeout_mark_lost(), lost_out
increases
9. sack_outs + lost_out > packets_out triggers since lost_out and
sack_outs increase repeatly
In function tcp_timeout_mark_lost(), tp->sacked_out will be cleared if
Step7 not happen and the warning will not be triggered. As suggested by
Denis and Eric, TCP_REPAIR_OPTIONS should be prohibited if data was
already sent.
socket-tcp tests in CRIU has been tested as follows:
$ sudo ./test/zdtm.py run -t zdtm/static/socket-tcp* --keep-going \
--ignore-taint
socket-tcp* represent all socket-tcp tests in test/zdtm/static/.
Fixes: b139ba4e90 ("tcp: Repair connection-time negotiated parameters")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code logic of handling the quirk of FEC_QUIRK_HAS_RACC.
If a SoC has the RACC quirk, the driver will enable the 16bit shift
by default in the probe function for a better performance.
This patch handles the logic in one place to make the logic simple
and clean. The patch optimizes the fec_enet_xdp_get_tx_queue function
according to Paolo Abeni's comments, and it also exludes the SoCs that
require to do frame swap from XDP support.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/lcs.c:2090:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
drivers/s390/net/lcs.c:2097:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of lcs_start_xmit() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/netiucv.c:1854:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = netiucv_tx,
^~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of netiucv_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/ctcm_main.c:1064:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcm_tx,
^~~~~~~
drivers/s390/net/ctcm_main.c:1072:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcmpc_tx,
^~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of ctc{mp,}m_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A problem about modprobe vc4 failed is triggered with the following log
given:
[ 420.327987] Error: Driver 'vc4_hvs' is already registered, aborting...
[ 420.333904] failed to register platform driver vc4_hvs_driver [vc4]: -16
modprobe: ERROR: could not insert 'vc4': Device or resource busy
The reason is that vc4_drm_register() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
fails, it returns without unregistering all the vc4 drivers, resulting the
vc4 can never be installed later.
A simple call graph is shown as below:
vc4_drm_register()
platform_register_drivers() # all vc4 drivers are registered
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without unregister drivers
Fixing this problem by checking the return value of
platform_driver_register() and do platform_unregister_drivers() if
error happened.
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103014705.109322-1-yuancan@huawei.com
The 1.4 GHz OPP requires supported silicon variant (T speed grade) and
also VDD_CORE to be at 0.85V. All production revisions of the AM625-SK
have both so we can enable the 1.4 GHz OPP for it. Any other boards
based on this design should verify that they have the right silicon
variant and the right power tree before adding 1.4 GHz support in their
board dts file.
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make ti-cpufreq driver depend on ARCH_K3 and set it to `default y` so it
is always enabled for platforms that it depends on.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Introduce an operating-points table for the A53 cores, containing only
frequency values as this platform operates on a fixed voltage for the
CPUs. Also provide opp-supported-hw values to ensure appropriate OPPs
are enabled based on which type of silicon is in use.
The latency between pre and post frequency transition was measured in
CPUFreq driver for all combinations of OPP changes. The average value
was selected as overall clock-latency-ns.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add ti,am625 SoC to the blacklist as the ti-cpufreq driver will handle
creating the cpufreq-dt platform device after it completes so it is not
created twice.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add support for TI K3 AM625 SoC to read speed and revision values from
hardware and pass to OPP layer.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vibhore Vardhan <vibhore@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
These WWAN network interface operations (create/delete/open/close)
are already protected by RTNL lock, i.e., wwan_ops.newlink(),
wwan_ops.dellink(), net_device_ops.ndo_open() and
net_device.ndo_stop() are called with RTNL lock held.
Therefore, this patch removes the unnecessary if_mutex.
Signed-off-by: Zhaoping Shu <zhaoping.shu@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MHI driver registers network device without setting the
needs_free_netdev flag, and does NOT call free_netdev() when
unregisters network device, which causes a memory leak.
This patch sets needs_free_netdev to true when registers
network device, which makes netdev subsystem call free_netdev()
automatically after unregister_netdevice().
Fixes: aa730a9905 ("net: wwan: Add MHI MBIM network driver")
Signed-off-by: HW He <hw.he@mediatek.com>
Signed-off-by: Zhaoping Shu <zhaoping.shu@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IOSM driver registers network device without setting the
needs_free_netdev flag, and does NOT call free_netdev() when
unregisters network device, which causes a memory leak.
This patch sets needs_free_netdev to true when registers
network device, which makes netdev subsystem call free_netdev()
automatically after unregister_netdevice().
Fixes: 2a54f2c779 ("net: iosm: net driver")
Signed-off-by: HW He <hw.he@mediatek.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Zhaoping Shu <zhaoping.shu@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the work queue based RX flow with a NAPI implementation
Remove rx_thread and dpmaif_rxq_work.
Enable GRO on RX path.
Introduce dummy network device. its responsibility is
- Binds one NAPI object for each DL HW queue and acts as
the agent of all those network devices.
- Use NAPI object to poll DL packets.
- Helps to dispatch each packet to the network interface.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Co-developed-by: Sreehari Kancharla <sreehari.kancharla@linux.intel.com>
Signed-off-by: Sreehari Kancharla <sreehari.kancharla@linux.intel.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Acked-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Acked-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hard_header_len is used by gro_list_prepare() but on Rx, there
is no header so use needed_headroom instead.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sreehari Kancharla <sreehari.kancharla@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, bpq_device_event() receives the message
and creates a new bpq device. In this case, the reference count value of
dev is hold once. But after "ifenslave -f bond2 rose1" command is
executed, the type of the bond device is changed to rose. When the bond
device is unregistered, bpq_device_event() will not put the dev reference
count.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, lapbeth_device_event() receives the
message and creates a new lapbeth device. In this case, the reference
count value of dev is hold once. But after "ifenslave -f bond2 rose1"
command is executed, the type of the bond device is changed to rose. When
the bond device is unregistered, lapbeth_device_event() will not put the
dev reference count.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For squashfs all needed functionality for idmapped mounts is already
implemented by the generic handlers in the VFS. Thus, it is sufficient
to just enable the corresponding FS_ALLOW_IDMAP flag to support
idmapped mounts.
We use this for unprivileged (user namespaced) containers based on
squashfs images as rootfs in GyroidOS.
A simple test using the mount-idmapped tool executed as user with
uid=1000 looks as follows:
$ mkdir test
$ echo "test" > test/test_file
$ mksquashfs test/ fs.img
$ sudo mkdir /mnt/test
$ sudo mkdir /mnt/mapped
$ sudo mount fs.img -o loop /mnt/test/
$ sudo ./mount-idmapped --map-mount b:1000:2000:1 /mnt/test/ /mnt/mapped/
$ mount | tail -n2
fs.img on /mnt/test type squashfs (ro,relatime,errors=continue)
fs.img on /mnt/mapped type squashfs (ro,relatime,idmapped,errors=continue)
$ ls -lan /mnt/test/
total 5
drwxr-xr-x 2 1000 1000 32 Okt 24 13:36 .
drwxr-xr-x 6 0 0 4096 Okt 24 13:38 ..
-rw-r--r-- 1 1000 1000 5 Okt 24 13:36 test_file
$ ls -lan /mnt/mapped/
total 5
drwxr-xr-x 2 2000 2000 32 Okt 24 13:36 .
drwxr-xr-x 6 0 0 4096 Okt 24 13:38 ..
-rw-r--r-- 1 2000 2000 5 Okt 24 13:36 test_file
Signed-off-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Phillip Lougher <phillip@squashfs.org.uk>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
The 'kzdev' field of struct 'zpci_aift' is an array of pointers to
'kvm_zdev' structs. Allocate the proper size accordingly.
Reported by Coccinelle:
WARNING: Use correct pointer type argument for sizeof
Fixes: 98b1d33dac ("KVM: s390: pci: do initial setup for AEN interpretation")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Link: https://lore.kernel.org/r/20221026013234.960859-1-rafaelmendsr@gmail.com
Message-Id: <20221026013234.960859-1-rafaelmendsr@gmail.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
When running under PV, the guest's TOD clock is under control of the
ultravisor and the hypervisor isn't allowed to change it. Hence, don't
allow userspace to change the guest's TOD clock by returning
-EOPNOTSUPP.
When userspace changes the guest's TOD clock, KVM updates its
kvm.arch.epoch field and, in addition, the epoch field in all state
descriptions of all VCPUs.
But, under PV, the ultravisor will ignore the epoch field in the state
description and simply overwrite it on next SIE exit with the actual
guest epoch. This leads to KVM having an incorrect view of the guest's
TOD clock: it has updated its internal kvm.arch.epoch field, but the
ultravisor ignores the field in the state description.
Whenever a guest is now waiting for a clock comparator, KVM will
incorrectly calculate the time when the guest should wake up, possibly
causing the guest to sleep for much longer than expected.
With this change, kvm_s390_set_tod() will now take the kvm->lock to be
able to call kvm_s390_pv_is_protected(). Since kvm_s390_set_tod_clock()
also takes kvm->lock, use __kvm_s390_set_tod_clock() instead.
The function kvm_s390_set_tod_clock is now unused, hence remove it.
Update the documentation to indicate the TOD clock attr calls can now
return -EOPNOTSUPP.
Fixes: 0f30350471 ("KVM: s390: protvirt: Do only reset registers that are accessible")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Nico Boehr <nrb@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/r/20221011160712.928239-2-nrb@linux.ibm.com
Message-Id: <20221011160712.928239-2-nrb@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
When ethtool config rx-vlan-filter, the driver will send
control command to firmware, then set to hardware in this patch.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
HINIC has a mailbox for PF-VF communication and the VF driver
could send port control command to PF driver via mailbox.
The control command only can be set to register in PF,
so add support in PF driver for VF PMD driver control
command when VF PMD driver work with linux PF driver.
Then, no need to add handlers to nic_vf_cmd_msg_handler[],
because the host driver just forwards it to the firmware.
Actually the firmware works on a coprocessor MGMT_CPU(inside the NIC)
which will recv and deal with these commands.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
The print cmd code is in hex, so using hex cmd code intead of
decimal is easy to check the value with print info.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
'reg' without any constraints allows multiple items which is not the
intention in DSA port schema (as physical port is expected to have only
one address).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'reg' without any constraints allows multiple items which is not the
intention for Ethernet controller's port number.
Constrain the 'reg' on AX88178 and LAN95xx USB Ethernet Controllers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support basic system-wide suspend and resume functions
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's actually preferable to use Generic regmap GPIO over other
simple approaches. Add a TODO item for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Support mode switch properly, which is not available before.
If SoC has two Ethernet controllers, by setting both of them into MII
mode, the first controller enters GMII mode, while the second
controller is effectively disabled. This requires configuring (and
maybe enabling) the second controller in the device tree, even though
it cannot be used.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2 improvements for the Chromebook handling in
acpi_video_get_backlight_type():
1. Also check for the "GOOG000C" ACPI HID used on some models
2. Move the Chromebook check to above the ACPI-video check normally
Chromebooks don't have ACPI video backlight support, but when
flashed with upstream coreboot builds they may have ACPI video
backlight support, but native should still be used/preferred then.
Suggested-by: Mr. Chromebox <mrchromebox@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add atomic operations support in post_send and poll_cq implementation.
Also, rename 'laddr' and 'lkey' in struct erdma_sge to 'addr' and 'key',
because this structure is used for both local and remote SGEs.
Signed-off-by: Cheng Xu <chengyou@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221107021845.44598-4-chengyou@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Introduce "capacity flags" field at where hardware put all zeros originally
in "query device" response. Using this field, hardware can report atomic
feature if supports.
Signed-off-by: Cheng Xu <chengyou@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221107021845.44598-3-chengyou@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
To support atomic operations, IB_ACCESS_REMOTE_ATOMIC right should be
passed to hardware for permission check. Since "access mode" field in FRMR
SQE and RegMr command is never used by hw, we remove the "access mode"
field, so that we can then have enough space to extend access fields.
Signed-off-by: Cheng Xu <chengyou@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221107021845.44598-2-chengyou@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The active link speed is currently hard-coded in irdma_query_port due
to which the port rate in ibstatus does reflect the active link speed.
Call ib_get_eth_speed in irdma_query_port to get the active link speed.
Fixes: b48c24c2d7 ("RDMA/irdma: Implement device supported verb APIs")
Reported-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Link: https://lore.kernel.org/r/20221104234957.1135-1-shiraz.saleem@intel.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The examples' cache nodes are incomplete as 'cache-unified' and
'cache-level' are required cache properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Document the typical order of API calls to used by new drivers and
controllers. Many existing controllers follow this order, but some do
not. This is especially true for controllers designed to work with one
particular PHY driver, which may not need a call to (for example)
phy_init.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20221018175841.1906611-1-sean.anderson@seco.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove redundant codes for getting the vbus supply of usb3 ports because
we get and control the vbus supply by the companion usb2 ports
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20221005084031.2154251-1-haotienh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The wake-up interrupt lines are entirely optional, avoid printing
messages that interrupts were not found by switching to the _optional
variant.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/20221026224450.2958762-1-f.fainelli@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Each of the CPSW9G ports in J721e support additional modes like QSGMII.
Add a new compatible for J721e to support the additional modes.
In TI's J721e, each of the CPSW9G ethernet interfaces can act as a
QSGMII main or QSGMII-SUB port. The QSGMII main interface is responsible
for performing auto-negotiation between the MAC and the PHY while the rest
of the interfaces are designated as QSGMII-SUB interfaces, indicating that
they will not be taking part in the auto-negotiation process.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20221026074532.109220-4-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The number of QSGMII main ports are specific to the device. TI's J7200 for
which the QSGMII main port property is fetched from the device-tree has
only one QSGMII main port. However, devices like TI's J721e support up to
two QSGMII main ports. Thus, the existing methods for fetching and using
the QSGMII main port are not scalable.
Update the existing methods for handling the QSGMII main ports and its
associated requirements to make it scalable for future devices.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20221026074532.109220-3-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J721e SoC supports additional PHY modes like QSGMII and SGMII
that are not supported on earlier SoCs. Add a compatible for it.
Extend ti,qsgmii-main-ports property to support selection of upto
two main ports at once across the two QSGMII interfaces.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221026074532.109220-2-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The USB PHY used in the Allwinner H616 SoC inherits some traits from its
various predecessors: it has four full PHYs like the H3, needs some
extra bits to be set like the H6, and puts SIDDQ on a different bit like
the A100. Plus it needs this weird PHY2 quirk.
Name all those properties in a new config struct and assign a new
compatible name to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221031111358.3387297-5-andre.przywara@arm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
At least the Allwinner H616 SoC requires a weird quirk to make most
USB PHYs work: Only port2 works out of the box, but all other ports
need some help from this port2 to work correctly: The CLK_BUS_PHY2 and
RST_USB_PHY2 clock and reset need to be enabled, and the SIDDQ bit in
the PMU PHY control register needs to be cleared. For this register to
be accessible, CLK_BUS_ECHI2 needs to be ungated. Don't ask ....
Instead of disguising this as some generic feature, treat it more like
a quirk (what it really is):
If the quirk bit is set, and we initialise a PHY other than PHY2, ungate
this one special clock, and clear the SIDDQ bit. We also pick the clock
and reset from PHY2 and enable them as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20221031111358.3387297-4-andre.przywara@arm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The USB PHY IP in the Allwinner H616 SoC requires a quirk that involves
some resources from port 2's PHY and HCI IP. In particular the PMU clock
for port 2 must be surely ungated before accessing the REG_HCI_PHY_CTL
register of port 2. To allow each USB port to be controlled
independently of port 2, we need a handle to that particular PMU clock
in the *PHY* node, as the HCI and PHY part might be handled by separate
drivers.
Add that clock to the requirements of the H616 PHY binding, so that a
PHY driver can apply the quirk in isolation, without requiring help from
port 2's HCI driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221031111358.3387297-3-andre.przywara@arm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should be disabling clocks when wake from USB is not needed. Since
this wasn't done, we had a clock imbalance since clocks were always
being enabled on resume.
Fixes: ae532b2b7a ("phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers")
Fixes: b0c0b66c0b ("phy: usb: Add support for wake and USB low power mode for 7211 S2/S5")
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/1665005418-15807-7-git-send-email-justinpopo6@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The logic was incorrect when switching to slow clock. We want the slow
clock if wake_enabled is set.
Fixes: ae532b2b7a ("phy: usb: Add "wake on" functionality for newer Synopsis XHCI controllers")
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/1665005418-15807-6-git-send-email-justinpopo6@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The BDC block requires the PLL lock in order to grab the PLL clock.
The phy auto-suspend feature turns off the phy when nothing is attached
leading to the PLL to not lock. This leads the BDC block to grab the AUX
clock instead of the PLL clock. This is not ideal, so lets turn this
feature off.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/1665005418-15807-5-git-send-email-justinpopo6@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using BIT and BITMASK macros makes it much easier to read and make
modifications. Also reordered some constants to be in numerical order.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/1665005418-15807-4-git-send-email-justinpopo6@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PHY's "wakeup_count" is not incrementing when waking from
WoL. The wakeup count can be found in sysfs at:
/sys/bus/platform/devices/rdb/*.usb-phy/power/wakeup_count.
The problem is that the system wakup event handler was being passed
the wrong "device" by the PHY driver.
Fixes: f1c0db40a3 ("phy: usb: Add "wake on" functionality")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/1665005418-15807-3-git-send-email-justinpopo6@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
