Each GSI execution environment (EE) is able to access many of the
GSI registers associated with the other EEs. A block of GSI
registers is contained within a region of memory, and an EE's
register offset can be determined by adding the register's base
offset to the product of the EE ID and a fixed constant.
Despite this possibility, the AP IPA code *never* accesses any GSI
registers other than its own. So there's no need to define the
macros that compute register offsets for other EEs.
Redefine the AP access macros to compute the offset the way the more
general "any EE" macro would, and get rid of the unneeded macros.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In of_mdiobus_register(), we should call of_node_put() for 'child'
escaped out of for_each_available_child_of_node().
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Co-developed-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220913125659.3331969-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PSI accounting is now done by the VM code, where it should have been
since the beginning.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: https://lore.kernel.org/r/20220915094200.139713-6-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
erofs uses an additional address space for compressed data read from disk
in addition to the one directly associated with the inode. Reading into
the lower address space is open coded using add_to_page_cache_lru instead
of using the filemap.c helper for page allocation micro-optimizations,
which means it is not covered by the MM PSI annotations for ->read_folio
and ->readahead, so add manual ones instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220915094200.139713-5-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
btrfs compressed reads try to always read the entire compressed chunk,
even if only a subset is requested. Currently this is covered by the
magic PSI accounting underneath submit_bio, but that is about to go
away. Instead add manual psi_memstall_{enter,leave} annotations.
Note that for readahead this really should be using readahead_expand,
but the additionals reads are also done for plain ->read_folio where
readahead_expand can't work, so this overall logic is left as-is for
now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: https://lore.kernel.org/r/20220915094200.139713-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To properly account for all refaults from file system logic, file systems
need to call psi_memstall_enter directly, so export it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: https://lore.kernel.org/r/20220915094200.139713-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
PSI tries to account for the cost of bringing back in pages discarded by
the MM LRU management. Currently the prime place for that is hooked into
the bio submission path, which is a rather bad place:
- it does not actually account I/O for non-block file systems, of which
we have many
- it adds overhead and a layering violation to the block layer
Add the accounting into the two places in the core MM code that read
pages into an address space by calling into ->read_folio and ->readahead
so that the entire file system operations are covered, to broaden
the coverage and allow removing the accounting in the block layer going
forward.
As psi_memstall_enter can deal with nested calls this will not lead to
double accounting even while the bio annotations are still present.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: https://lore.kernel.org/r/20220915094200.139713-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Due to i915_perf assuming that it can use the i915_gem_context reference
to protect its i915->gem.contexts.list iteration, we need to defer removal
of the context from the list until last reference to the context is put.
However, there is a risk of triggering kernel warning on contexts list not
empty at driver release time if we deleagate that task to a worker for
i915_gem_context_release_work(), unless that work is flushed first.
Unfortunately, it is not flushed on driver release. Fix it.
Instead of additionally calling flush_workqueue(), either directly or via
a new dedicated wrapper around it, replace last call to
i915_gem_drain_freed_objects() with existing i915_gem_drain_workqueue()
that performs both tasks.
Fixes: 75eefd8258 ("drm/i915: Release i915_gem_context from a worker")
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: stable@kernel.org # v5.16+
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916092403.201355-2-janusz.krzysztofik@linux.intel.com
(cherry picked from commit 1cec344424)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This reverts commit a09b314005.
Dusty Mabe reported consistent hang during CoreOS shutdown with a MD
RAID1 setup. Although apparently similar hangs happened before,
and this patch most likely is not the root cause it made it much
more severe. Revert it until we can figure out what is going on
with the md driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220919144049.978907-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit
238c91115c ("x86/dumpstack: Fix misleading instruction pointer error message")
changed the "Code:" line in bug reports when RIP is an invalid pointer.
In particular, the report currently says (for example):
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
RIP: 0010:0x0
Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6.
That
Unable to access opcode bytes at RIP 0xffffffffffffffd6.
is quite confusing as RIP value is 0, not -42. That -42 comes from
"regs->ip - PROLOGUE_SIZE", because Code is dumped with some prologue
(and epilogue).
So do not mention "RIP" on this line in this context.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/b772c39f-c5ae-8f17-fe6e-6a2bc4d1f83b@kernel.org
MAX31760 is a precision fan speed controller with nonvolatile lookup table.
Device has one internal and one external temperature sensor support.
Controls two fans and measures their speeds. Generates hardware alerts when
programmable max and critical temperatures are exceeded.
Signed-off-by: Ibrahim Tilki <Ibrahim.Tilki@analog.com>
Reviewed-by: Nurettin Bolucu <Nurettin.Bolucu@analog.com>
Link: https://lore.kernel.org/r/20220910171945.48088-2-Ibrahim.Tilki@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This turns the FTGPIO010 irqchip immutable.
Tested on the D-Link DIR-685.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
If creation of software node fails, the locally allocated string
array is left unfreed. Free it on error path.
Fixes: 6fda593f30 ("gpio: mockup: Convert to use software nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
We now remove the device's debugfs entries when unbinding the driver.
This now causes a NULL-pointer dereference on module exit because the
platform devices are unregistered *after* the global debugfs directory
has been recursively removed. Fix it by unregistering the devices first.
Fixes: 303e6da994 ("gpio: mockup: remove gpio debugfs when remove device")
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
* Add a quirk for Asus UM325UAZ to make GPIO interrupts working
The following is an automated git shortlog grouped by driver:
gpiolib:
- acpi: Add a quirk for Asus UM325UAZ
- acpi: Add support to ignore programming an interrupt
-----BEGIN PGP SIGNATURE-----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=4yCI
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.1-1' of gitolite.kernel.org:pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.1-1
* Add a quirk for Asus UM325UAZ to make GPIO interrupts working
- handle number of queue changes in the TCP and RDMA drivers
(Daniel Wagner)
- allow changing the number of queues in nvmet (Daniel Wagner)
- also consider host_iface when checking ip options (Daniel Wagner)
- don't map pages which can't come from HIGHMEM (Fabio M. De Francesco)
- avoid unnecessary flush bios in nvmet (Guixin Liu)
- shrink and better pack the nvme_iod structure (Keith Busch)
- add comment for unaligned "fake" nqn (Linjun Bao)
- print actual source IP address through sysfs "address" attr
(Martin Belanger)
- various cleanups (Jackie Liu, Wolfram Sang, Genjian Zhang)
-----BEGIN PGP SIGNATURE-----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=WnST
-----END PGP SIGNATURE-----
Merge tag 'nvme-6.1-2022-09-20' of git://git.infradead.org/nvme into for-6.1/block
Pull NVMe updates from Christoph:
"nvme updates for Linux 6.1
- handle number of queue changes in the TCP and RDMA drivers
(Daniel Wagner)
- allow changing the number of queues in nvmet (Daniel Wagner)
- also consider host_iface when checking ip options (Daniel Wagner)
- don't map pages which can't come from HIGHMEM (Fabio M. De Francesco)
- avoid unnecessary flush bios in nvmet (Guixin Liu)
- shrink and better pack the nvme_iod structure (Keith Busch)
- add comment for unaligned "fake" nqn (Linjun Bao)
- print actual source IP address through sysfs "address" attr
(Martin Belanger)
- various cleanups (Jackie Liu, Wolfram Sang, Genjian Zhang)"
* tag 'nvme-6.1-2022-09-20' of git://git.infradead.org/nvme:
nvme-tcp: print actual source IP address through sysfs "address" attr
nvmet-tcp: don't map pages which can't come from HIGHMEM
nvme-pci: move iod dma_len fill gaps
nvme-pci: iod npages fits in s8
nvme-pci: iod's 'aborted' is a bool
nvme-pci: remove nvme_queue from nvme_iod
nvme: consider also host_iface when checking ip options
nvme-rdma: handle number of queue changes
nvme-tcp: handle number of queue changes
nvmet: expose max queues to configfs
nvmet: avoid unnecessary flush bio
nvmet-auth: remove redundant parameters req
nvmet-auth: clean up with done_kfree
nvme-auth: remove the redundant req->cqe->result.u16 assignment operation
nvme: move from strlcpy with unused retval to strscpy
nvme: add comment for unaligned "fake" nqn
If x is not 0, __ffs(x) is equivalent to:
(unsigned long)__builtin_ctzl(x)
And if x is not ~0UL, ffz(x) is equivalent to:
(unsigned long)__builtin_ctzl(~x)
Because __builting_ctzl() returns an int, a cast to (unsigned long) is
necessary to avoid potential warnings on implicit casts.
Concerning the edge cases, __builtin_ctzl(0) is always undefined,
whereas __ffs(0) and ffz(~0UL) may or may not be defined, depending on
the processor. Regardless, for both functions, developers are asked to
check against 0 or ~0UL so replacing __ffs() or ffz() by
__builting_ctzl() is safe.
For x86_64, the current __ffs() and ffz() implementations do not
produce optimized code when called with a constant expression. On the
contrary, the __builtin_ctzl() folds into a single instruction.
However, for non constant expressions, the __ffs() and ffz() asm
versions of the kernel remains slightly better than the code produced
by GCC (it produces a useless instruction to clear eax).
Use __builtin_constant_p() to select between the kernel's
__ffs()/ffz() and the __builtin_ctzl() depending on whether the
argument is constant or not.
** Statistics **
On a allyesconfig, before...:
$ objdump -d vmlinux.o | grep tzcnt | wc -l
3607
...and after:
$ objdump -d vmlinux.o | grep tzcnt | wc -l
2600
So, roughly 27.9% of the calls to either __ffs() or ffz() were using
constant expressions and could be optimized out.
(tests done on linux v5.18-rc5 x86_64 using GCC 11.2.1)
Note: on x86_64, the BSF instruction produces TZCNT when used with the
REP prefix (which explain the use of `grep tzcnt' instead of `grep bsf'
in above benchmark). c.f. [1]
[1] e26a44a2d6 ("x86: Use REP BSF unconditionally")
[ bp: Massage commit message. ]
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Link: https://lore.kernel.org/r/20220511160319.1045812-1-mailhol.vincent@wanadoo.fr
For x86_64, the current ffs() implementation does not produce optimized
code when called with a constant expression. On the contrary, the
__builtin_ffs() functions of both GCC and clang are able to fold the
expression into a single instruction.
** Example **
Consider two dummy functions foo() and bar() as below:
#include <linux/bitops.h>
#define CONST 0x01000000
unsigned int foo(void)
{
return ffs(CONST);
}
unsigned int bar(void)
{
return __builtin_ffs(CONST);
}
GCC would produce below assembly code:
0000000000000000 <foo>:
0: ba 00 00 00 01 mov $0x1000000,%edx
5: b8 ff ff ff ff mov $0xffffffff,%eax
a: 0f bc c2 bsf %edx,%eax
d: 83 c0 01 add $0x1,%eax
10: c3 ret
<Instructions after ret and before next function were redacted>
0000000000000020 <bar>:
20: b8 19 00 00 00 mov $0x19,%eax
25: c3 ret
And clang would produce:
0000000000000000 <foo>:
0: b8 ff ff ff ff mov $0xffffffff,%eax
5: 0f bc 05 00 00 00 00 bsf 0x0(%rip),%eax # c <foo+0xc>
c: 83 c0 01 add $0x1,%eax
f: c3 ret
0000000000000010 <bar>:
10: b8 19 00 00 00 mov $0x19,%eax
15: c3 ret
Both examples clearly demonstrate the benefit of using __builtin_ffs()
instead of the kernel's asm implementation for constant expressions.
However, for non constant expressions, the kernel's ffs() asm version
remains better for x86_64 because, contrary to GCC, it doesn't emit the
CMOV assembly instruction, c.f. [1] (noticeably, clang is able optimize
out the CMOV call).
Use __builtin_constant_p() to select between the kernel's ffs() and
the __builtin_ffs() depending on whether the argument is constant or
not.
As a side benefit, replacing the ffs() function declaration by a macro
also removes below -Wshadow warning:
./arch/x86/include/asm/bitops.h:283:28: warning: declaration of 'ffs' shadows a built-in function [-Wshadow]
283 | static __always_inline int ffs(int x)
** Statistics **
On a allyesconfig, before...:
$ objdump -d vmlinux.o | grep bsf | wc -l
1081
...and after:
$ objdump -d vmlinux.o | grep bsf | wc -l
792
So, roughly 26.7% of the calls to ffs() were using constant
expressions and could be optimized out.
(tests done on linux v5.18-rc5 x86_64 using GCC 11.2.1)
[1] commit ca3d30cc02 ("x86_64, asm: Optimise fls(), ffs() and fls64()")
[ bp: Massage commit message. ]
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Link: https://lore.kernel.org/r/20220511160319.1045812-1-mailhol.vincent@wanadoo.fr
Alexandru Tachici says:
====================
net: ethernet: adi: Add ADIN1110 support
The ADIN1110 is a low power single port 10BASE-T1L MAC-PHY
designed for industrial Ethernet applications. It integrates
an Ethernet PHY core with a MAC and all the associated analog
circuitry, input and output clock buffering.
ADIN1110 MAC-PHY encapsulates the ADIN1100 PHY. The PHY registers
can be accessed through the MDIO MAC registers.
We are registering an MDIO bus with custom read/write in order
to let the PHY to be discovered by the PAL. This will let
the ADIN1100 Linux driver to probe and take control of
the PHY.
The ADIN2111 is a low power, low complexity, two-Ethernet ports
switch with integrated 10BASE-T1L PHYs and one serial peripheral
interface (SPI) port.
The device is designed for industrial Ethernet applications using
low power constrained nodes and is compliant with the IEEE 802.3cg-2019
Ethernet standard for long reach 10 Mbps single pair Ethernet (SPE).
The switch supports various routing configurations between
the two Ethernet ports and the SPI host port providing a flexible
solution for line, daisy-chain, or ring network topologies.
The ADIN2111 supports cable reach of up to 1700 meters with ultra
low power consumption of 77 mW. The two PHY cores support the
1.0 V p-p operating mode and the 2.4 V p-p operating mode defined
in the IEEE 802.3cg standard.
The device integrates the switch, two Ethernet physical layer (PHY)
cores with a media access control (MAC) interface and all the
associated analog circuitry, and input and output clock buffering.
The device also includes internal buffer queues, the SPI and
subsystem registers, as well as the control logic to manage the reset
and clock control and hardware pin configuration.
Access to the PHYs is exposed via an internal MDIO bus. Writes/reads
can be performed by reading/writing to the ADIN2111 MDIO registers
via SPI.
On probe, for each port, a struct net_device is allocated and
registered. When both ports are added to the same bridge, the driver
will enable offloading of frame forwarding at the hardware level.
Driver offers STP support. Normal operation on forwarding state.
Allows only frames with the 802.1d DA to be passed to the host
when in any of the other states.
When both ports of ADIN2111 belong to the same SW bridge a maximum
of 12 FDB entries will offloaded by the hardware and are marked as such.
====================
Link: https://lore.kernel.org/r/20220913122629.124546-1-andrei.tachici@stud.acs.upb.ro
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add bindings for the ADIN1110/2111 MAC-PHY/SWITCH.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ADIN1110 is a low power single port 10BASE-T1L MAC-PHY
designed for industrial Ethernet applications. It integrates
an Ethernet PHY core with a MAC and all the associated analog
circuitry, input and output clock buffering.
ADIN1110 MAC-PHY encapsulates the ADIN1100 PHY. The PHY registers
can be accessed through the MDIO MAC registers.
We are registering an MDIO bus with custom read/write in order
to let the PHY to be discovered by the PAL. This will let
the ADIN1100 Linux driver to probe and take control of
the PHY.
The ADIN2111 is a low power, low complexity, two-Ethernet ports
switch with integrated 10BASE-T1L PHYs and one serial peripheral
interface (SPI) port.
The device is designed for industrial Ethernet applications using
low power constrained nodes and is compliant with the IEEE 802.3cg-2019
Ethernet standard for long reach 10 Mbps single pair Ethernet (SPE).
The switch supports various routing configurations between
the two Ethernet ports and the SPI host port providing a flexible
solution for line, daisy-chain, or ring network topologies.
The ADIN2111 supports cable reach of up to 1700 meters with ultra
low power consumption of 77 mW. The two PHY cores support the
1.0 V p-p operating mode and the 2.4 V p-p operating mode defined
in the IEEE 802.3cg standard.
The device integrates the switch, two Ethernet physical layer (PHY)
cores with a media access control (MAC) interface and all the
associated analog circuitry, and input and output clock buffering.
The device also includes internal buffer queues, the SPI and
subsystem registers, as well as the control logic to manage the reset
and clock control and hardware pin configuration.
Access to the PHYs is exposed via an internal MDIO bus. Writes/reads
can be performed by reading/writing to the ADIN2111 MDIO registers
via SPI.
On probe, for each port, a struct net_device is allocated and
registered. When both ports are added to the same bridge, the driver
will enable offloading of frame forwarding at the hardware level.
Driver offers STP support. Normal operation on forwarding state.
Allows only frames with the 802.1d DA to be passed to the host
when in any of the other states.
When both ports of ADIN2111 belong to the same SW bridge a maximum
of 12 FDB entries will offloaded by the hardware and are marked as such.
Co-developed-by: Lennart Franzen <lennart@lfdomain.com>
Signed-off-by: Lennart Franzen <lennart@lfdomain.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add additional PHY IDs for the internal PHYs of adin1110 and adin2111.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Today remove callbacks of platform devices return an int. This is unfortunate
because the device core ignores the return value and so the platform code only
emits a warning (and still removes the device).
The longterm quest is to make these remove callbacks return void instead.
This series is a preparation for that, with the goal to make the remove
callbacks obviously always return 0. This way when the prototype of
these functions is changed to return void, the change is straight
forward and easy to review.
Link: https://lore.kernel.org/r/20220718121409.171773-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Make INTERCONNECT_QCOM tristate so that icc-common.c can be
compiled as a module.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914064122.16222-1-quic_hyiwei@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
When doing sizeof() and giving as argument a dereference of
a pointer-to-a-pointer object, clang will issue a warning.
Eliminate the warning by passing struct <name>*
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
I$ prefetch is enabled when sending a TPC kernel to initialize the TPC
memory, and it has a restriction that the base address will be aligned
to 8KB.
Currently the base address is 128 bytes from the start address of the
device SRAM, so prefetching will start 128 bytes before the actual
kernel memory.
Modify the kernel address to be 8KB aligned.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
roccat_report_event() is responsible for registering
roccat-related reports in struct roccat_device.
int roccat_report_event(int minor, u8 const *data)
{
struct roccat_device *device;
struct roccat_reader *reader;
struct roccat_report *report;
uint8_t *new_value;
device = devices[minor];
new_value = kmemdup(data, device->report_size, GFP_ATOMIC);
if (!new_value)
return -ENOMEM;
report = &device->cbuf[device->cbuf_end];
/* passing NULL is safe */
kfree(report->value);
...
The registered report is stored in the struct roccat_device member
"struct roccat_report cbuf[ROCCAT_CBUF_SIZE];".
If more reports are received than the "ROCCAT_CBUF_SIZE" value,
kfree() the saved report from cbuf[0] and allocates a new reprot.
Since there is no lock when this kfree() is performed,
kfree() can be performed even while reading the saved report.
static ssize_t roccat_read(struct file *file, char __user *buffer,
size_t count, loff_t *ppos)
{
struct roccat_reader *reader = file->private_data;
struct roccat_device *device = reader->device;
struct roccat_report *report;
ssize_t retval = 0, len;
DECLARE_WAITQUEUE(wait, current);
mutex_lock(&device->cbuf_lock);
...
report = &device->cbuf[reader->cbuf_start];
/*
* If report is larger than requested amount of data, rest of report
* is lost!
*/
len = device->report_size > count ? count : device->report_size;
if (copy_to_user(buffer, report->value, len)) {
retval = -EFAULT;
goto exit_unlock;
}
...
The roccat_read() function receives the device->cbuf report and
delivers it to the user through copy_to_user().
If the N+ROCCAT_CBUF_SIZE th report is received while copying of
the Nth report->value is in progress, the pointer that copy_to_user()
is working on is kfree()ed and UAF read may occur. (race condition)
Since the device node of this driver does not set separate permissions,
this is not a security vulnerability, but because it is used for
requesting screen display of profile or dpi settings,
a user using the roccat device can apply udev to this device node or
There is a possibility to use it by giving.
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before we switched to ->read_skb(), ->read_sock() was passed with
desc.count=1, which technically indicates we only read one skb per
->sk_data_ready() call. However, for TCP, this is not true.
TCP at least has sk_rcvlowat which intentionally holds skb's in
receive queue until this watermark is reached. This means when
->sk_data_ready() is invoked there could be multiple skb's in the
queue, therefore we have to read multiple skbs in tcp_read_skb()
instead of one.
Fixes: 965b57b469 ("net: Introduce a new proto_ops ->read_skb()")
Reported-by: Peilin Ye <peilin.ye@bytedance.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20220912173553.235838-1-xiyou.wangcong@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To be forward-backward compatible with the firmware in the initial
communication during preboot, we need to remove the validation of the
header size. This will allow us to add more fields to the
lkd_fw_comms_desc structure.
Instead of the validation of the header size, we just print warning
when some mismatch in descriptor has been revealed, and we calculate
the CRC base on descriptor size reported by the firmware instead of
calculating it ourselves.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Newer ASICs code changes more often, has more chance to fail
compilation. So, let's compile them first so errors in those files
will fail compilation sooner.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Return the value rtsx_usb_send_cmd() directly instead of storing it in
another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220920064648.215375-1-ye.xingchen@zte.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though it is unlikely to ever make a difference, let's use u32
consistently for the size of the load_options provided by the firmware
(aka the command line)
While at it, do some general cleanup too: use efi_char16_t, avoid using
options_chars in places where it really means options_size, etc.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Fuzzers like to scribble over sb_bsize_shift but in reality it's very
unlikely that this field would be corrupted on its own. Nevertheless it
should be checked to avoid the possibility of messy mount errors due to
bad calculations. It's always a fixed value based on the block size so
we can just check that it's the expected value.
Tested with:
mkfs.gfs2 -O -p lock_nolock /dev/vdb
for i in 0 -1 64 65 32 33; do
gfs2_edit -p sb field sb_bsize_shift $i /dev/vdb
mount /dev/vdb /mnt/test && umount /mnt/test
done
Before this patch we get a withdraw after
[ 76.413681] gfs2: fsid=loop0.0: fatal: invalid metadata block
[ 76.413681] bh = 19 (type: exp=5, found=4)
[ 76.413681] function = gfs2_meta_buffer, file = fs/gfs2/meta_io.c, line = 492
and with UBSAN configured we also get complaints like
[ 76.373395] UBSAN: shift-out-of-bounds in fs/gfs2/ops_fstype.c:295:19
[ 76.373815] shift exponent 4294967287 is too large for 64-bit type 'long unsigned int'
After the patch, these complaints don't appear, mount fails immediately
and we get an explanation in dmesg.
Reported-by: syzbot+dcf33a7aae997956fe06@syzkaller.appspotmail.com
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
In preparation for FORTIFY_SOURCE performing run-time destination buffer
bounds checking for memcpy(), specify the destination output buffer
explicitly, instead of asking memcpy() to write past the end of what looked
like a fixed-size object.
Notice that srp_rsp[] is a pointer to a structure that contains
flexible-array member data[]:
struct srp_rsp {
...
__be32 sense_data_len;
__be32 resp_data_len;
u8 data[];
};
link: https://github.com/KSPP/linux/issues/201
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220909022943.8896-1-hbh25y@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
This reverts commit 32eeeed963.
As the fix for endpoint configuration split is reverted at next, do
another revert here for a clean patch application.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit ff878b408a.
Unfortunately the recent fix seems bringing another regressions with
PulseAudio / pipewire, at least for Steinberg and MOTU devices.
As a temporary solution, do a straight revert. The issue for Android
will be revisited again later by another different fix (if any).
Fixes: ff878b408a ("ALSA: usb-audio: Split endpoint setups for hw_params and prepare")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216500
Link: https://lore.kernel.org/r/20220920113929.25162-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Return the value inb() directly instead of storing it in another redundant
variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220920064605.215318-1-ye.xingchen@zte.com.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some opcodes are used in hardware internally, and driver does not care
about them. So, we change them to reserved opcodes in driver.
Signed-off-by: Cheng Xu <chengyou@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220909093822.33868-4-chengyou@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Many of erdma's includes are redundant, because they are already included
indirectly by kernel headers or custom headers. So we remove all the
unnecessary direct-includes. Besides, add linux/pci.h to erdma.h because
it's also used in the file.
Signed-off-by: Cheng Xu <chengyou@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220909093822.33868-3-chengyou@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
erdma_post_cmd_wait does not use the 'u64 *req' input parameter directly.
So it is better to define it to 'void *req', and by this we can eliminate
the casting when calling erdma_post_cmd_wait.
Signed-off-by: Cheng Xu <chengyou@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220909093822.33868-2-chengyou@linux.alibaba.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Merge series from Martin Povišer <povik+lin@cutebit.org>:
there's a CS42L83 headphone jack codec found in Apple computers (in the
recent 'Apple Silicon' ones as well as in earlier models, one example
[1]). The part isn't publicly documented, but it appears almost
identical to CS42L42, for which we have a driver in kernel. This series
adapts the CS42L42 driver to the new part, and makes one change in
anticipation of a machine driver for the Apple computers.
Patch 1 adds new compatible to the cs42l42 schema.
Patches 2 to 7 are taken from Richard's recent series [2] adding
soundwire support to cs42l42. They are useful refactorings to build on
in the later patches, and also this way our work doesn't diverge.
(I fixed missing free_irq path in cs42l42_init, did
s/Soundwire/SoundWire/ in changelogs, rebased.)
Patch 8 exports some regmap-related symbols from cs42l42.c so they can
be used to create cs42l83 regmap in cs42l83-i2c.c later.
Patch 9 is the cs42l83 support proper.
Patch 10 implements 'set_bclk_ratio' on the cs42l42 core. This will be
called by the upcoming ASoC machine driver for 'Apple Silicon' Macs.
(We have touched on this change to be made in earlier discussion, see
[3] and replies.)
Patch 11 brings cs42l42-i2c.c in sync with cs42l83-i2c.c on
dev_err_probe() usage.
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
This patchset solves a known issue with ES8336 platforms wrt MCLK
selection. Most of the devices use the MCLK0 signal, but some devices
do use the MCLK1 signal.
The MCLK is defined in the topology, it would be a nightmare to
generate more topology files just for one MCLK difference. With a
minor extension to the intel-nhlt library, the MCLK information can be
found by parsing the NHLT table, and we can override the mclk_id at
boot time.
The only known issues for this platform remain the detection of GPIO
and microphone connections, currently only possible with manual
quirks.
Thanks to Eugene J. Markow for testing this patchset.
The NHLT is already used to determine which SSP is connected to an
audio codec, we can parse the SSP blob to get the mclk_id from NHLT.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220919115350.43104-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
