mac_txen time is to inform TMAC tx after rx air end.
Modify 8852c value to meet TB SIFS time.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-7-pkshih@realtek.com
Prebkf time is to inform generating tx command if remaining backoff
time less than this setting value.
It might cause SER if generating tx command early in security mode.
Signed-off-by: Chia-Yuan Li <leo.li@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-6-pkshih@realtek.com
Calling rtw89_leave_lps() should hold rtwdev::mutex.
So, fix it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-5-pkshih@realtek.com
Sometimes, BB might encounter RX problem on OFDM 6M. It's not quite
easy to happen, but if it happens, we will keep getting stuck on RX.
And, since we cannot properly receive layer 2 ACK, it also casues TX
problem, e.g. constantly retrying TX. Eventually, after some time, we
would get disconnected due to abnormal behavior.
Update break setting and phy status parsing time to make BB get out
of stuck state faster.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-3-pkshih@realtek.com
Without this patch, our hardware attempts to perform dma while device
cpu restarts, and leads to iommu page faults caused by invalid requests.
Some platforms show warning messages as below:
rtw89_8852ce 0000:01:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT
domain=0x000a address=0x10000000004 flags=0x0030]
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220704023453.19935-2-pkshih@realtek.com
In current flow, FW is asynchronously loaded after alloc_hw(). It defers
the decision on FW feature map. It makes things difficult for us to decide
whether to hook chanctx ops, which should be decided while alloc_hw() is
calling. Still, asynchronous gets its advantages. So, we want to resolve
this without dropping them.
Based on multi-FW flag, RTW89_MFW_SIG, we can determine runtime FW is
multi-FW (MFW) or single FW (SFW). Both of them have a quite small chunk
for header at the head. The difference is that MFW doesn't describe version
code in its header while SFW does. So, we plan to extend MFW header for
version code. After that, in both cases, we can determine FW feature map by
just FW header. And, according to the map, we can decide chanctx.
So, we call request_partial_firmware_into_buf() to request a quite small
chunk before alloc_hw() to get a early FW feature map without affecting
things much and only use early map to decide whether to hook chanctx ops.
It means that if non-extended MFW is used at runtime, driver just acts
without chanctx as before. If extended MFW or SFW, which supports required
FW features, is used at runtime, driver can hook chanctx ops to mac80211 if
chip has configured support_chanctx_num > 0.
Besides, key point for now to support single one chanctx is whether HW scan
is supported at runtime. So, we configure all chip's support_chanctx_num to
1, and check if HW scan is supported at runtime via early FW feature map.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-14-pkshih@realtek.com
Some HW features are required if we hook chanctx ops to mac80211. With it,
mac80211 would expect the HW-supported variant ops exists on some behavior,
e.g. HW scan. But, HW features may depend on chip's FW or its development.
Besides, how many chanctx can be supported also depends on chip design.
We can neither decide whether to generally support chanctx ops nor how many
chanctx can be supported.
So, support_chanctx_num is added under chip info to deal with this by chip.
For now, all chip configure support_chanctx_num as 0. We haven't really
hook chanctx ops yet. So, chip can run without mac80211 chanctx as before.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-13-pkshih@realtek.com
Support mac80211 chanctx series ops. Still, currently support
single channel. Based on this premise, things should be similar
to before. So, we haven't dealt with relationship between vif
and chanctx in depth. Instead, we leave both ::assign_vif()
and ::unassign_vif() as noops for now.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-12-pkshih@realtek.com
After supporting more than one channel, we need entity mode to decide
how to set current channel(s) on the sub-entities. This decision may
happen on set_channel() and rtw89_core_set_chip_txpwr().
For now, we support single one channel and use only first HW entry,
i.e. RTW89_SUB_ENTITY_0, RTW89_MAC_0, RTW89_PHY_0. Without something
unexpected, the entity mode should always be RTW89_ENT_MODE_SCC after
recalcated, where SCC means single channel concurrency. So, an assert
is added in set_channel() and rtw89_core_set_chip_txpwr().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-11-pkshih@realtek.com
While idle, we need a default chandef to set channel for things,
such as scan. Before support of mac80211 chanctx, mac80211 would
configure a default one on ieee80211_hw::conf::chandef. And we
just queried it whenever we did set channel. However, after support
of mac80211 chanctx, the flow won't work like before.
Besides, we don't now query chandef from ieee80211_hw::conf::chandef
either. So, similar to mac80211 without using chanctx, we configure
the default chandef with ieee80211_channel of index 0 in 2GHz.
Although we have not added the support of mac80211 chanctx here,
this configuration should be compatible before that. So, we commit
this ahead.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-10-pkshih@realtek.com
Originally, we didn't support mac80211 chanctx, so it's expected that
ieee80211_hw::conf::chandef would be filled by mac80211. And then, we
could just query it whenever we need the current chandef.
However, we are planing to support mac80211 chanctx. After that, the
above assumption would be broken. So, we adjust a bit ahead to reduce
future works about mac80211 chanctx.
After this, we don't query ieee80211_hw::conf::chandef directly, and
we add a map, entity_map, to HAL to indicate which chandef came from
stack. And it will later be used to recalcate entity mode.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-9-pkshih@realtek.com
For future support on multiple channels by multiple sub-entities,
we need to manage parameters of each channel instance like rtw89_chan,
rtw89_mac_idx, rtw89_phy_idx. So, we adjust related channel callback
functions and centrally conrtol these parameters in set_channel().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-8-pkshih@realtek.com
For future support on multiple channels, there will be settings of
multiple sub-entities that we need to control. We don't want such
settings to be scattered all over the place. So, we centrally manage
controls of rtw89_phy_idx for RFK in set_channel().
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-7-pkshih@realtek.com
For future support on multiple channels, it would be disturbing if we
still allow scattered leaf functions of TX power to query and manage
channel related control by themselves.
So, query rtw89_chan only on top functions. Then, pass it via functions
to make sure that the values coming from the same struct rtw89_chan.
Besides, fix rtw8852a_set_txpwr_offset() from rtw8852a_set_txpwr_ctrl()
to rtw8852a_set_txpwr(). TX power offset should consider current band,
so move it to chip_ops::set_txpwr() which will be called every time that
channel is set.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-6-pkshih@realtek.com
Sometimes we need to write current rtw89_chan outside set_channel(),
e.g. during HW scan, we adjust it to align FW process through C2H.
However, we don't have full parameters to fill entire rtw89_chan.
And it will breakage if we update only part of current rtw89_chan.
That is what we don't want to see because most flows throughout
driver treat rtw89_chan as a whole.
So, we divide struct rtw89_chan to basic part and derived part. The
basic part contains the parameters which we are always able to know.
And the derived part will be calculated by the basic part. Then, a
central function, rtw89_chan_create(), is added to deal with this.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-5-pkshih@realtek.com
We are planning to support mac80211 chanctx. To reduce future works,
the driver architecture is adjusted first to isolate related things.
According to chip, our HW may have multiple sub-entities to support
multiple mac80211 chanctx. Struct rtw89_chan has been introduced for
things about channel/band/subband/... Now introduce struct rtw89_chan_rcd
to record difference after assigning new one of struct rtw89_chan.
We will implement and support chanctx with single channel first, i.e.
only use entry in RTW89_SUB_ENTITY_0, before handling dual channels.
Our hierarchy in planning will become as the following.
DEV
-> HAL
---> entity (manage status across sub-entities)
-----> sub-entity[*] (support mac80211 chanctx)
where each sub-entity contains one struct rtw89_chan.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-4-pkshih@realtek.com
Introduce struct rtw89_chan ahead to encapsulate stuffs from struct
rtw89_channel_params. These stuffs have a clone in HAL and are used
throughout driver. After multiple channels support, it's expected that
each channel instance has a configuration of them. So, we refine them
with struct rtw89_chan by precise type first, and will re-arrange HAL
by struct rtw89_chan in the following as well.
(No logic has changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-3-pkshih@realtek.com
We need to invoke the callback of the changed band at the first
set_channel() after every power-off. Originally, we forced the
channel to be 0 when doing power-off, and then determined things
by comparing channel with 0.
However, deciding on such things by channel might be confusing.
It's also confusing to use this kind of decision when we consider
multiple channels in the follow-up patches. So, another flag,
entity_active, is added ahead to HAL to deal with this.
Besides, we also need to check if entity is active when we set
TX power.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-2-pkshih@realtek.com
Remove the code to unregister acpi_video backlight devices when
a native backlight device gets registered later.
Now that the acpi_video backlight device registration is a separate step
which runs later, after the drm/kms driver is done setting up its own
native backlight device, it is no longer necessary to monitor for a
native (BACKLIGHT_RAW) device showing up later and to then unregister
the acpi_video backlight device(s).
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On x86/ACPI boards the acpi_video driver will usually initialize before
the kms driver (except i915). This causes /sys/class/backlight/acpi_video0
to show up and then the kms driver registers its own native backlight
device after which the drivers/acpi/video_detect.c code unregisters
the acpi_video0 device (when acpi_video_get_backlight_type()==native).
This means that userspace briefly sees 2 devices and the disappearing of
acpi_video0 after a brief time confuses the systemd backlight level
save/restore code, see e.g.:
https://bbs.archlinux.org/viewtopic.php?id=269920
To fix this make backlight class device registration a separate step
done by a new acpi_video_register_backlight() function. The intend is for
this to be called by the drm/kms driver *after* it is done setting up its
own native backlight device. So that acpi_video_get_backlight_type() knows
if a native backlight will be available or not at acpi_video backlight
registration time, avoiding the add + remove dance.
Note the new acpi_video_register_backlight() function is also called from
a delayed work to ensure that the acpi_video backlight devices does get
registered if necessary even if there is no drm/kms driver or when it is
disabled.
Changes in v2:
- Make register_backlight_delay a module parameter, mainly so that it can
be disabled by Nvidia binary driver users
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When acpi_video_register() has not run yet the video_bus_head will be
empty, so there is no need to check the register_count flag first.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the list_del removing an acpi_video_bus from video_bus_head
on teardown to before the teardown is done, to avoid code iterating
over the video_bus_head list seeing acpi_video_bus objects on there
which are (partly) torn down already.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
All x86/ACPI kms drivers which register native/BACKLIGHT_RAW type
backlight devices call acpi_video_backlight_use_native() now. This sets
__acpi_video_get_backlight_type()'s internal static native_available flag.
This makes the backlight_device_get_by_type(BACKLIGHT_RAW) check
unnecessary.
Relying on the cached native_available value not only is simpler, it will
also work correctly in cases where then native backlight registration was
skipped because of acpi_video_backlight_use_native() returning false.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Before this commit when we want userspace to use the acpi_video backlight
device we register both the GPU's native backlight device and acpi_video's
firmware acpi_video# backlight device. This relies on userspace preferring
firmware type backlight devices over native ones.
Registering 2 backlight devices for a single display really is
undesirable, don't register the GPU's native backlight device when
another backlight device should be used.
Changes in v2:
- Add nouveau_acpi_video_backlight_use_native() wrapper to avoid unresolved
symbol errors on non X86
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add led configuration for pcb8291 and pcb8309. Both pcbs have 4 leds which
are connected to the sgpio controller.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220902062447.443846-1-horatiu.vultur@microchip.com
This reverts commit 8cb339f1c1 as it
throws up a bunch of sparse warnings as reported by the kernel test
robot.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202209020044.CX2PfZzM-lkp@intel.com
Fixes: 8cb339f1c1 ("usb: gadget: udc-xilinx: replace memcpy with memcpy_toio")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This contains two fixes to qcom sdw driver which resolve duplicate reset
control get and second one fixes device array indices.
-----BEGIN PGP SIGNATURE-----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=dJt1
-----END PGP SIGNATURE-----
Merge tag 'soundwire-6.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus
Vinod writes:
"soundwire fixes for v6.0
This contains two fixes to qcom sdw driver which resolve duplicate reset
control get and second one fixes device array indices."
* tag 'soundwire-6.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: qcom: fix device status array range
soundwire: qcom: remove duplicate reset control get
In loopback_jiffies_timer_pos_update(), we are getting jiffies twice.
First time for playback, second time for capture. Jiffies can be updated
between these two calls and if the capture jiffies is larger, extra zeros
will be filled in the capture buffer.
Change to get jiffies once and use it for both playback and capture.
Signed-off-by: Pattara Teerapong <pteerapong@chromium.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220901144036.4049060-1-pteerapong@chromium.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Print both old and new versions of microcode after a reload is complete
because knowing the previous microcode version is sometimes important
from a debugging perspective.
[ bp: Massage commit message. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20220829181030.722891-1-ashok.raj@intel.com
This is a followup of commit c67b85558f ("ipv6: tcp: send consistent
autoflowlabel in TIME_WAIT state"), but for SYN_RECV state.
In some cases, TCP sends a challenge ACK on behalf of a SYN_RECV request.
WHen this happens, we want to use the flow label that was used when
the prior SYNACK packet was sent, instead of another one.
After his patch, following packetdrill passes:
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+.2 < S 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
+0 > (flowlabel 0x11) S. 0:0(0) ack 1 <...>
// Test if a challenge ack is properly sent (same flowlabel than prior SYNACK)
+.01 < . 4000000000:4000000000(0) ack 1 win 320
+0 > (flowlabel 0x11) . 1:1(0) ack 1
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220831203729.458000-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 2c87c6f9fb.
Meanwhile it turned out that the following commit is the proper
workaround for the issue that 2c87c6f9fb tries to address.
a3a57bf07d ("net: stmmac: work around sporadic tx issue on link-up")
It's nor clear why the to be reverted commit helped for one user,
for others it didn't make a difference.
Fixes: 2c87c6f9fb ("net: phy: meson-gxl: improve link-up behavior")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8deeeddc-6b71-129b-1918-495a12dc11e3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This has been validated on the Ocelot/Felix switch family (NXP LS1028A)
and should be relevant to any switch driver that offloads the tc-flower
and/or tc-matchall actions trap, drop, accept, mirred, for which DSA has
operations.
TEST: gact drop and ok (skip_hw) [ OK ]
TEST: mirred egress flower redirect (skip_hw) [ OK ]
TEST: mirred egress flower mirror (skip_hw) [ OK ]
TEST: mirred egress matchall mirror (skip_hw) [ OK ]
TEST: mirred_egress_to_ingress (skip_hw) [ OK ]
TEST: gact drop and ok (skip_sw) [ OK ]
TEST: mirred egress flower redirect (skip_sw) [ OK ]
TEST: mirred egress flower mirror (skip_sw) [ OK ]
TEST: mirred egress matchall mirror (skip_sw) [ OK ]
TEST: trap (skip_sw) [ OK ]
TEST: mirred_egress_to_ingress (skip_sw) [ OK ]
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220831170839.931184-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Return value directly from nsim_dev_reload_create()
instead of getting value from redundant variable ret.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn>
Link: https://lore.kernel.org/r/20220831154329.305372-1-cui.jinpeng2@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The open code is defined as a new helper function(netif_oper_up) on netdev.h,
the code is dev->operstate == IF_OPER_UP || dev->operstate == IF_OPER_UNKNOWN.
Thus, replace the open code to netif_oper_up. This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Link: https://lore.kernel.org/r/20220831125845.1333-1-claudiajkang@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
etf_enable_offload() is only called when q->offload is false in
etf_init(). So remove true check in etf_enable_offload().
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Link: https://lore.kernel.org/r/20220831092919.146149-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_SECURITY_NETWORK is disabled, there will be build warnings
from resolve_btfids:
WARN: resolve_btfids: unresolved symbol bpf_lsm_socket_socketpair
......
WARN: resolve_btfids: unresolved symbol bpf_lsm_inet_conn_established
Fixing it by wrapping these BTF ID definitions by CONFIG_SECURITY_NETWORK.
Fixes: 69fd337a97 ("bpf: per-cgroup lsm flavor")
Fixes: 9113d7e48e ("bpf: expose bpf_{g,s}etsockopt to lsm cgroup")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20220901065126.3856297-1-houtao@huaweicloud.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
An invalid argument to KVM_SET_MP_STATE has no effect other than making the
vCPU fail to run at the next KVM_RUN. Since it is extremely unlikely that
any userspace is relying on it, fail with -EINVAL just like for other
architectures.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a guest PEBS counter is cross-mapped by a host counter, software
will remove the corresponding bit in the arr[global_ctrl].guest and
expect hardware to perform a change of state "from enable to disable"
via the msr_slot[] switch during the vmx transaction.
The real world is that if user adjust the counter overflow value small
enough, it still opens a tiny race window for the previously PEBS-enabled
counter to write cross-mapped PEBS records into the guest's PEBS buffer,
when arr[global_ctrl].guest has been prioritised (switch_msr_special stuff)
to switch into the enabled state, while the arr[pebs_enable].guest has not.
Close this window by clearing invalid bits in the arr[global_ctrl].guest.
Cc: linux-perf-users@vger.kernel.org
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sean Christopherson <seanjc@google.com>
Fixes: 854250329c ("KVM: x86/pmu: Disable guest PEBS temporarily in two rare situations")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20220831033524.58561-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When allocating memory for mci_ctl2_banks fails, KVM doesn't release
mce_banks leading to memoryleak. Fix this issue by calling kfree()
for it when kcalloc() fails.
Fixes: 281b52780b ("KVM: x86: Add emulation for MSR_IA32_MCx_CTL2 MSRs.")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Message-Id: <20220901122300.22298-1-linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM should not claim to virtualize unknown IA32_ARCH_CAPABILITIES
bits. When kvm_get_arch_capabilities() was originally written, there
were only a few bits defined in this MSR, and KVM could virtualize all
of them. However, over the years, several bits have been defined that
KVM cannot just blindly pass through to the guest without additional
work (such as virtualizing an MSR promised by the
IA32_ARCH_CAPABILITES feature bit).
Define a mask of supported IA32_ARCH_CAPABILITIES bits, and mask off
any other bits that are set in the hardware MSR.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Fixes: 5b76a3cff0 ("KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Vipin Sharma <vipinsh@google.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-Id: <20220830174947.2182144-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it
needs constantly polling control pipe until the host received the WMT
event, thus, we should require to specifically acquire PM counter on the
USB to prevent the interface from entering auto suspended while WMT
cmd/event in progress.
Fixes: a1c49c434e ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
... and don't check for impossible conditions - file_inode() is
never NULL in anything seen by ->release() and neither is its
->i_mapping.
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
