We already depend on runtime PM to get the power domains and clocks for
most of the devices supported by the vc4 driver, so let's just select it
to make sure it's there.
Link: https://lore.kernel.org/r/20220629123510.1915022-38-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
(cherry picked from commit f1bc386b31)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Make sure that only the valid combinations of FCS/CRC stripping and
VLAN stripping offloads are allowed.
You cannot have FCS/CRC stripping disabled while VLAN stripping is
enabled - this breaks the correctness of the FCS/CRC.
If administrator tries to enable VLAN stripping when FCS/CRC stripping is
disabled, the request should be rejected.
If administrator tries to disable FCS/CRC stripping when VLAN stripping
is enabled, the request should be rejected if VLANs are configured. If
there is no VLAN configured, then both FCS/CRC and VLAN stripping should
be disabled.
Testing Hints:
The default settings after driver load are:
- VLAN C-Tag offloads are enabled
- VLAN S-Tag offloads are disabled
- FCS/CRC stripping is enabled
Restore the default settings before each test with the command:
ethtool -K eth0 rx-fcs off rxvlan on txvlan on rx-vlan-stag-hw-parse off
tx-vlan-stag-hw-insert off
Test 1:
Disable FCS/CRC and VLAN stripping:
ethtool -K eth0 rx-fcs on rxvlan off
Try to enable VLAN stripping:
ethtool -K eth0 rxvlan on
Expected: VLAN stripping request is rejected
Test 2:
Try to disable FCS/CRC stripping:
ethtool -K eth0 rx-fcs on
Expected: VLAN stripping is also disabled, as there are no VLAN
configured
Test 3:
Add a VLAN:
ip link add link eth0 eth0.42 type vlan id 42
ip link set eth0 up
Try to disable FCS/CRC stripping:
ethtool -K eth0 rx-fcs on
Expected: FCS/CRC stripping request is rejected
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver can allow the user to configure whether the CRC aka the FCS
(Frame Check Sequence) is DMA'd to the host as part of the receive
buffer. The driver usually wants this feature disabled so that the
hardware checks the FCS and strips it in order to save PCI bandwidth.
Control the reception of FCS to the host using the command:
ethtool -K eth0 rx-fcs <on|off>
The default shown in ethtool -k eth0 | grep fcs; should be "off", as the
hardware will drop any frame with a bad checksum, and DMA of the
checksum is useless overhead especially for small packets.
Testing Hints:
test the FCS/CRC arrives with received packets using
tcpdump -nnpi eth0 -xxxx
and it should show crc data as the last 4 bytes of the packet. Can also
use wireshark to turn on CRC checking and check the data is correct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Co-developed-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the port does not support USB PD, prevent transition to PD
only states when power supply property is written. In this case,
TCPM transitions to SNK_NEGOTIATE_CAPABILITIES
which should not be the case given that the port is not pd_capable.
[ 84.308251] state change SNK_READY -> SNK_NEGOTIATE_CAPABILITIES [rev3 NONE_AMS]
[ 84.308335] Setting usb_comm capable false
[ 84.323367] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:5000 ret:0
[ 84.323376] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]
Fixes: e9e6e164ed ("usb: typec: tcpm: Support non-PD mode")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220817215410.1807477-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The top-level platform selection is mostly meaningless these days after
almost everything is sorted below the CONFIG_ARCH_MULTIPLATFORM, with
the only exception being the 20+ year old StrongARM based machines.
Make this more consistent by removing the entire choice statement and
moving the StrongARM specific options into regular platform specific
Kconfig files.
The three platforms (footbridge, rpc and sa1100) are still mutually
exclusive and cannot coexist with other ARMv4/v5 machines, but since
there are only three of them and we will not add more, this can be
expressed using Kconfig 'depends on' statements.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is only one plat-* directory left, and the MACHINE variable is
only used for the mach/*.h header path.
Simplify this by removing the checks for ARCH_MULTIPLATFORM and
ARM_SINGLE_ARMV7M, and just adding the include directories for the
remaining three platforms manually.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are a number of old Makefile.boot files that remain from the
multiplatform conversion, and three that are still in use.
These provide the "ZRELADDR", "PARAMS_PHYS" and "INITRD_PHYS" values
that are platform specific. It turns out that we can generally just
derive this from information that is available elsewhere:
- ZRELADDR is normally detected at runtime with the
CONFIG_AUTO_ZRELADDR flag, but also needed to be passed to
for 'make uImage'. In a multiplatform kernel, one always has
to pass this as the $(LOADADDR) variable, but in the StrongARM
kernels we can derive it from the sum of $(CONFIG_PHYS_OFFSET)
and $(TEXT_OFFSET) that are already known.
- PARAMS_PHYS and INITRD_PHYS are only used for bootpImage, which
in turn is only used for the pre-ATAGS 'param_struct' based boot
interface on StrongARM based machines with old boot loaders.
They can both be derived from CONFIG_PHYS_OFFSET and a machine
specific offset for the initrd, so all of the logic for these
can be part of arch/arm/boot/bootp/Makefile.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Turning on NOP_USB_XCEIV as builtin broke the TUSB6010 driver because
of an older issue with the depencency.
It is not necessary to forbid NOP_USB_XCEIV=y in combination with
USB_MUSB_HDRC=m, but only the reverse, which causes the link failure
from the original Kconfig change.
Use the correct dependency to still allow NOP_USB_XCEIV=n or
NOP_USB_XCEIV=y but forbid NOP_USB_XCEIV=m when USB_MUSB_HDRC=m
to fix the multi_v7_defconfig for tusb.
Fixes: ab37a7a890 ("ARM: multi_v7_defconfig: Make NOP_USB_XCEIV driver built-in")
Fixes: c044247965 ("usb: musb: Fix randconfig build issues for Kconfig options")
Cc: stable <stable@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220818135737.3143895-10-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take the mmap_read_lock() when using the VMA in
binder_alloc_print_pages() and when checking for a VMA in
binder_alloc_new_buf_locked().
It is worth noting binder_alloc_new_buf_locked() drops the VMA read lock
after it verifies a VMA exists, but may be taken again deeper in the
call stack, if necessary.
Fixes: a43cfc87ca (android: binder: stop saving a pointer to the VMA)
Cc: stable <stable@kernel.org>
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Reported-by: syzbot+a7b60a176ec13cafb793@syzkaller.appspotmail.com
Tested-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Link: https://lore.kernel.org/r/20220810160209.1630707-1-Liam.Howlett@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A transaction of type BINDER_TYPE_WEAK_HANDLE can fail to increment the
reference for a node. In this case, the target proc normally releases
the failed reference upon close as expected. However, if the target is
dying in parallel the call will race with binder_deferred_release(), so
the target could have released all of its references by now leaving the
cleanup of the new failed reference unhandled.
The transaction then ends and the target proc gets released making the
ref->proc now a dangling pointer. Later on, ref->node is closed and we
attempt to take spin_lock(&ref->proc->inner_lock), which leads to the
use-after-free bug reported below. Let's fix this by cleaning up the
failed reference on the spot instead of relying on the target to do so.
==================================================================
BUG: KASAN: use-after-free in _raw_spin_lock+0xa8/0x150
Write of size 4 at addr ffff5ca207094238 by task kworker/1:0/590
CPU: 1 PID: 590 Comm: kworker/1:0 Not tainted 5.19.0-rc8 #10
Hardware name: linux,dummy-virt (DT)
Workqueue: events binder_deferred_func
Call trace:
dump_backtrace.part.0+0x1d0/0x1e0
show_stack+0x18/0x70
dump_stack_lvl+0x68/0x84
print_report+0x2e4/0x61c
kasan_report+0xa4/0x110
kasan_check_range+0xfc/0x1a4
__kasan_check_write+0x3c/0x50
_raw_spin_lock+0xa8/0x150
binder_deferred_func+0x5e0/0x9b0
process_one_work+0x38c/0x5f0
worker_thread+0x9c/0x694
kthread+0x188/0x190
ret_from_fork+0x10/0x20
Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Cc: stable <stable@kernel.org> # 4.14+
Link: https://lore.kernel.org/r/20220801182511.3371447-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD SPI controller hardware seems to expect the FIFO buffer to be
fully setup with the details of all transfers in the SPI message before
it is able to start processing the data in a reliable way.
Furthermore, it imposes a strict ordering restriction, in the sense that
all TX transfers must be handled prior any RX transfer.
Hence, let's ensure amd_spi_execute_opcode() is called only once, after
all TX transfers have been setup, and process any remaining RX transfers
afterwards, in a second iteration.
Additionally, get rid of the unnecessary AMD_SPI_XFER_TX/RX defines and
improve error handling.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20220818010059.403776-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, an unresolved regulator supply reference upon calling
regulator_register on an always-on or boot-on regulator caused
set_machine_constraints to be called twice.
This in turn may initialize the regulator twice, leading to voltage
glitches that are timing-dependent. A simple, unrelated configuration
change may be enough to hide this problem, only to be surfaced by
chance.
One such example is the SD-Card voltage regulator in a NanoPI R4S that
would not initialize reliably unless the registration flow was just
complex enough to allow the regulator to properly reset between calls.
Fix this by re-arranging regulator_register, trying resolve the
regulator's supply early enough that set_machine_constraints does not
need to be called twice.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Link: https://lore.kernel.org/r/20220818124646.6005-1-christian@kohlschutter.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the max_raw_read and max_raw_write limits in regmap_spi struct
do not take into account the additional size of the transmitted register
address and padding. This may result in exceeding the maximum permitted
SPI message size, which could cause undefined behaviour, e.g. data
corruption.
Fix regmap_get_spi_bus() to properly adjust the above mentioned limits
by reserving space for the register address/padding as set in the regmap
configuration.
Fixes: f231ff38b7 ("regmap: spi: Set regmap max raw r/w from max_transfer_size")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220818104851.429479-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It should be size of the struct sof_ipc4_src, not data pointer pass to
sof_update_ipc_object().
Fixes: b85f4fc40d ("ASoC: SOF: add ipc4 SRC module support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220818081751.2407066-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Matti Vaittinen <mazziesaccount@gmail.com>:
A few* drivers seem to use pattern demonstrated by pseudocode:
- devm_regulator_get()
- regulator_enable()
- devm_add_action_or_reset(regulator_disable())
Introducing devm helpers for this pattern would remove bunch of code from
drivers. Typically following:
- replace 3 calls (devm_regulator_get[_optional](), regulator_enable(),
devm_add_action_or_reset()) with just one
(devm_regulator_get_enable[_optional]()).
- drop disable callback.
- remove stored pointer to struct regulator - which can lead to problem
when an devm action for regulator_disable is used.
I believe this simplifies things by removing some dublicated code.
The suggested managed 'get_enable' APIs do not return the pointer to
regulators for user because any call to regulator_disable()
(or regulator_enable()) may easily lead to regulator enable count imbalance
upon device detach. (Eg, if someone calls regulator_disable() and the
device is then detached before user has re-enabled the regulator). Not
returning the pointer to obtained regulator to caller is a good hint that
the enable/disable should not be manually handled when these APIs are used.
OTOH, not returning the pointer reduces the use-cases by not allowing
the consumers to perform other regulator actions. For example request the
voltages. A few drivers which used the "get, enable,
devm_action_to_disable" did also query the voltages. The API does not suit
needs of such users.
Commit
d23d33ea0f ("x86/microcode: Taint and warn on late loading")
started tainting the kernel after microcode late loading.
There is some history behind why x86 microcode started doing the late
loading stop_machine() rendezvous. Document the whole situation.
No functional changes.
[ bp: Fix typos, heavily massage. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220813223825.3164861-2-ashok.raj@intel.com
We do test on a virtio scsi device (/dev/sda) and the default mq
scheduler is 'none'. We found a IO hung as following:
blk_finish_plug
blk_mq_plug_issue_direct
scsi_mq_get_budget
//get budget_token fail and sdev->restarts=1
scsi_end_request
scsi_run_queue_async
//sdev->restart=0 and run queue
blk_mq_request_bypass_insert
//add request to hctx->dispatch list
//continue to dispath plug list
blk_mq_dispatch_plug_list
blk_mq_try_issue_list_directly
//success issue all requests from plug list
After .get_budget fail, scsi_mq_get_budget will increase 'restarts'.
Normally, it will run hw queue when io complete and set 'restarts'
as 0. But if we run queue before adding request to the dispatch list
and blk_mq_dispatch_plug_list also success issue all requests, then
on one will run queue, and the request will be stall in the dispatch
list and cannot complete forever.
It is wrong to use last request of plug list to decide if run queue is
needed since all the remained requests in plug list may be from other
hctxs. To fix the bug, pass run_queue as true always to
blk_mq_request_bypass_insert().
Fix-suggested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Fixes: dc5fc361d8 ("block: attempt direct issue of plug list")
Link: https://lore.kernel.org/r/20220803023355.3687360-1-yuyufen@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Older Intel CPUs that are not in the affected processor list for MMIO
Stale Data vulnerabilities currently report "Not affected" in sysfs,
which may not be correct. Vulnerability status for these older CPUs is
unknown.
Add known-not-affected CPUs to the whitelist. Report "unknown"
mitigation status for CPUs that are not in blacklist, whitelist and also
don't enumerate MSR ARCH_CAPABILITIES bits that reflect hardware
immunity to MMIO Stale Data vulnerabilities.
Mitigation is not deployed when the status is unknown.
[ bp: Massage, fixup. ]
Fixes: 8d50cdf8b8 ("x86/speculation/mmio: Add sysfs reporting for Processor MMIO Stale Data")
Suggested-by: Andrew Cooper <andrew.cooper3@citrix.com>
Suggested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/a932c154772f2121794a5f2eded1a11013114711.1657846269.git.pawan.kumar.gupta@linux.intel.com
A few regulator consumer drivers seem to be just getting a regulator,
enabling it and registering a devm-action to disable the regulator at
the driver detach and then forget about it.
We can simplify this a bit by adding a devm-helper for this pattern.
Add devm_regulator_get_enable() and devm_regulator_get_enable_optional()
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/ed7b8841193bb9749d426f3cb3b199c9460794cd.1660292316.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on a patch by Mark Hemment <markhemm@googlemail.com> and
incorporating very sane suggestions from Linus.
The point here is to have the default case with FSRM - which is supposed
to be the majority of x86 hw out there - if not now then soon - be
directly inlined into the instruction stream so that no function call
overhead is taking place.
Drop the early clobbers from the @size and @addr operands as those are
not needed anymore since we have single instruction alternatives.
The benchmarks I ran would show very small improvements and a PF
benchmark would even show weird things like slowdowns with higher core
counts.
So for a ~6m running the git test suite, the function gets called under
700K times, all from padzero():
<...>-2536 [006] ..... 261.208801: padzero: to: 0x55b0663ed214, size: 3564, cycles: 21900
<...>-2536 [006] ..... 261.208819: padzero: to: 0x7f061adca078, size: 3976, cycles: 17160
<...>-2537 [008] ..... 261.211027: padzero: to: 0x5572d019e240, size: 3520, cycles: 23850
<...>-2537 [008] ..... 261.211049: padzero: to: 0x7f1288dc9078, size: 3976, cycles: 15900
...
which is around 1%-ish of the total time and which is consistent with
the benchmark numbers.
So Mel gave me the idea to simply measure how fast the function becomes.
I.e.:
start = rdtsc_ordered();
ret = __clear_user(to, n);
end = rdtsc_ordered();
Computing the mean average of all the samples collected during the test
suite run then shows some improvement:
clear_user_original:
Amean: 9219.71 (Sum: 6340154910, samples: 687674)
fsrm:
Amean: 8030.63 (Sum: 5522277720, samples: 687652)
That's on Zen3.
The situation looks a lot more confusing on Intel:
Icelake:
clear_user_original:
Amean: 19679.4 (Sum: 13652560764, samples: 693750)
Amean: 19743.7 (Sum: 13693470604, samples: 693562)
(I ran it twice just to be sure.)
ERMS:
Amean: 20374.3 (Sum: 13910601024, samples: 682752)
Amean: 20453.7 (Sum: 14186223606, samples: 693576)
FSRM:
Amean: 20458.2 (Sum: 13918381386, sample s: 680331)
The original microbenchmark which people were complaining about:
for i in $(seq 1 10); do dd if=/dev/zero of=/dev/null bs=1M status=progress count=65536; done 2>&1 | grep copied
32207011840 bytes (32 GB, 30 GiB) copied, 1 s, 32.2 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.93069 s, 35.6 GB/s
37597741056 bytes (38 GB, 35 GiB) copied, 1 s, 37.6 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.78017 s, 38.6 GB/s
62020124672 bytes (62 GB, 58 GiB) copied, 2 s, 31.0 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 2.13716 s, 32.2 GB/s
60010004480 bytes (60 GB, 56 GiB) copied, 1 s, 60.0 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.14129 s, 60.2 GB/s
53212086272 bytes (53 GB, 50 GiB) copied, 1 s, 53.2 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.28398 s, 53.5 GB/s
55698259968 bytes (56 GB, 52 GiB) copied, 1 s, 55.7 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.22507 s, 56.1 GB/s
55306092544 bytes (55 GB, 52 GiB) copied, 1 s, 55.3 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.23647 s, 55.6 GB/s
54387539968 bytes (54 GB, 51 GiB) copied, 1 s, 54.4 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.25693 s, 54.7 GB/s
50566529024 bytes (51 GB, 47 GiB) copied, 1 s, 50.6 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.35096 s, 50.9 GB/s
58308165632 bytes (58 GB, 54 GiB) copied, 1 s, 58.3 GB/s
68719476736 bytes (69 GB, 64 GiB) copied, 1.17394 s, 58.5 GB/s
Now the same thing with smaller buffers:
for i in $(seq 1 10); do dd if=/dev/zero of=/dev/null bs=1M status=progress count=8192; done 2>&1 | grep copied
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.28485 s, 30.2 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.276112 s, 31.1 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.29136 s, 29.5 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.283803 s, 30.3 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.306503 s, 28.0 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.349169 s, 24.6 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.276912 s, 31.0 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.265356 s, 32.4 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.28464 s, 30.2 GB/s
8589934592 bytes (8.6 GB, 8.0 GiB) copied, 0.242998 s, 35.3 GB/s
is also not conclusive because it all depends on the buffer sizes,
their alignments and when the microcode detects that cachelines can be
aggregated properly and copied in bigger sizes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/CAHk-=wh=Mu_EYhtOmPn6AxoQZyEh-4fo2Zx3G7rBv1g7vwoKiw@mail.gmail.com
Only Thunderbolt 3 routers need the xHCI connection flow. This also
ensures the router actually has both lane adapters (1 and 3). While
there move declaration of the boolean variables inside the block where
they are being used.
Fixes: 30a4eca69b ("thunderbolt: Add internal xHCI connect flows for Thunderbolt 3 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The received notification packet is held in pkg->buffer and not in pkg
itself. Fix this by using the correct buffer.
Fixes: 81a54b5e19 ("thunderbolt: Let the connection manager handle all notifications")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If early probe of HDAudio bus driver fails e.g.: due to missing
firmware file, snd_hda_codec_shutdown() ends in manipulating
uninitialized codec->pcm_list_head causing page fault.
Initialization of HDAudio codec in ASoC is split in two:
- snd_hda_codec_device_init()
- snd_hda_codec_device_new()
snd_hda_codec_device_init() is called during probe_codecs() by HDAudio
bus driver while snd_hda_codec_device_new() is called by
codec-component's ->probe(). The second call will not happen until all
components required by related sound card are present within the ASoC
framework. With firmware failing to load during the PCI's deferred
initialization i.e.: probe_work(), no platform components are ever
registered. HDAudio codec enumeration is done at that point though, so
the codec components became registered to ASoC framework, calling
snd_hda_codec_device_init() in the process.
Now, during platform reboot snd_hda_codec_shutdown() is called for every
codec found on the HDAudio bus causing oops if any of them has not
completed both of their initialization steps. Relocating field
initialization fixes the issue.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220816111727.3218543-7-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are no users for snd_hdac_ext_bus_device_init() and
snd_hdac_ext_bus_device_exit().
While at it, remove hdac_to_hda_priv() too for the exact same reason.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220816111727.3218543-6-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With all HDAudio drivers aligned to make use of the same constructor,
have codec freed on the device release regardless of its type.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220816111727.3218543-5-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To make snd_hda_codec_device_init() the only constructor for struct
hda_codec instances remaining tasks are:
1) no struct may wrap struct hda_codec as its base type
2) bus drivers (skylake and sof) which are the current hdac_ext users
need to be adjusted to make use of newly added codec init and exit
routines instead
3) as bus drivers (skylake and sof) are to be responsible for creating
codec device and assigning it to hdac_hda_priv->codec,
hdac_hda_dev_probe() has to be freed of that job
To keep git bisect happy, all of these in made in one-go.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220816111727.3218543-4-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Preliminary step in making snd_hda_codec_device_init() the only
constructor for struct hda_codec instances. To do that, existing usage
of hdac_ext equivalents has to be dropped.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220816111727.3218543-3-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Preliminary step in making snd_hda_codec_device_init() the only
constructor for struct hda_codec instances. To do that, existing usage
of hdac_ext equivalents has to be dropped.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220816111727.3218543-2-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This restores the call to inode_has_no_xattr() in the function
__file_remove_privs(). In case the dentry_meeds_remove_privs() returned
0, the function inode_has_no_xattr() was not called.
Signed-off-by: Stefan Roesch <shr@fb.com>
Fixes: faf99b5635 ("fs: add __remove_file_privs() with flags parameter")
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Link: https://lore.kernel.org/r/20220816153158.1925040-1-shr@fb.com
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Because of incompatible 2nd source si7021, removing hdc1080 node from
device tree, and move node probe to user-space layer.
Signed-off-by: Potin Lai <potin.lai.pt@gmail.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Link: https://lore.kernel.org/r/20220810004338.329832-3-potin.lai.pt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add an IPMB node for USB debug card (13-0010) to support IPMI
communication.
Signed-off-by: Potin Lai <potin.lai.pt@gmail.com>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Link: https://lore.kernel.org/r/20220810004338.329832-2-potin.lai.pt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600A3 EVB has the following I2C devices:
- ADT7490 at 0x2e
- EEPROM at 0xa0
- LM75 at 0x9a
The bus these devices appear on can be configured by jumpers. The device
tree is configured with the buses given by the default jumper settings.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Link: https://lore.kernel.org/r/20220623094717.3873328-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add support for configuring the Self Refresh Power Down (SRPD)
inactivity timeout on Broadcom STB chips. This is used to conserve power
when the DRAM activity is reduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220812222533.2428033-4-f.fainelli@gmail.com
Document the "srpd" and "frequency" sysfs attributes exposed by
the brcmstb_memc driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220812222533.2428033-3-f.fainelli@gmail.com
Document the Broadcom STB memory controller which is a trivial binding
for now with a set of compatible strings and single register.
Since we introduce this binding, the section in
Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt is removed
and this binding is referenced instead.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
[krzk: correct path in brcm,brcmstb.txt]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220812222533.2428033-2-f.fainelli@gmail.com
IPsec code relies on valid priv->fs pointer that is the case in NIC
flow, but not correct in uplink. Before commit that mentioned in the
Fixes line, that pointer was valid in all flows as it was allocated
together with priv struct.
In addition, the cleanup representors routine called to that
not-initialized priv->fs pointer and its internals which caused NULL
deference.
So, move FS allocation to be as early as possible.
Fixes: af8bbf7300 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/ae46fa5bed3c67f937bfdfc0370101278f5422f1.1660639564.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Fixes for Ocelot driver statistics
This series contains bug fixes for the ocelot drivers (both switchdev
and DSA). Some concern the counters exposed to ethtool -S, and others to
the counters exposed to ifconfig. I'm aware that the changes are fairly
large, but I wanted to prioritize on a proper approach to addressing the
issues rather than a quick hack.
Some of the noticed problems:
- bad register offsets for some counters
- unhandled concurrency leading to corrupted counters
- unhandled 32-bit wraparound of ifconfig counters
The issues on the ocelot switchdev driver were noticed through code
inspection, I do not have the hardware to test.
This patch set necessarily converts ocelot->stats_lock from a mutex to a
spinlock. I know this affects Colin Foster's development with the SPI
controlled VSC7512. I have other changes prepared for net-next that
convert this back into a mutex (along with other changes in this area).
====================
Link: https://lore.kernel.org/r/20220816135352.1431497-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than reading the stats64 counters directly from the 32-bit
hardware, it's better to rely on the output produced by the periodic
ocelot_port_update_stats().
It would be even better to call ocelot_port_update_stats() right from
ocelot_get_stats64() to make sure we report the current values rather
than the ones from 2 seconds ago. But we need to export
ocelot_port_update_stats() from the switch lib towards the switchdev
driver for that, and future work will largely undo that.
There are more ocelot-based drivers waiting to be introduced, an example
of which is the SPI-controlled VSC7512. In that driver's case, it will
be impossible to call ocelot_port_update_stats() from ndo_get_stats64
context, since the latter is atomic, and reading the stats over SPI is
sleepable. So the compromise taken here, which will also hold going
forward, is to report 64-bit counters to stats64, which are not 100% up
to date.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With so many counter addresses recently discovered as being wrong, it is
desirable to at least have a central database of information, rather
than two: one through the SYS_COUNT_* registers (used for
ndo_get_stats64), and the other through the offset field of struct
ocelot_stat_layout elements (used for ethtool -S).
The strategy will be to keep the SYS_COUNT_* definitions as the single
source of truth, but for that we need to expand our current definitions
to cover all registers. Then we need to convert the ocelot region
creation logic, and stats worker, to the read semantics imposed by going
through SYS_COUNT_* absolute register addresses, rather than offsets
of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been
SYS_CNT, by the way).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 2 methods can run concurrently, and one will change the window of
counters (SYS_STAT_CFG_STAT_VIEW) that the other sees. The fix is
similar to what commit 7fbf6795d1 ("net: mscc: ocelot: fix mutex lock
error during ethtool stats read") has done for ethtool -S.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
