commit e0547c81bf upstream.
On ThinkPad P50 SKUs with an Nvidia Quadro M1000M instead of the M2000M
variant, the BIOS does not always reset the secondary Nvidia GPU during
reboot if the laptop is configured in Hybrid Graphics mode. The reason is
unknown, but the following steps and possibly a good bit of patience will
reproduce the issue:
1. Boot up the laptop normally in Hybrid Graphics mode
2. Make sure nouveau is loaded and that the GPU is awake
3. Allow the Nvidia GPU to runtime suspend itself after being idle
4. Reboot the machine, the more sudden the better (e.g. sysrq-b may help)
5. If nouveau loads up properly, reboot the machine again and go back to
step 2 until you reproduce the issue
This results in some very strange behavior: the GPU will be left in exactly
the same state it was in when the previously booted kernel started the
reboot. This has all sorts of bad side effects: for starters, this
completely breaks nouveau starting with a mysterious EVO channel failure
that happens well before we've actually used the EVO channel for anything:
nouveau 0000:01:00.0: disp: chid 0 mthd 0000 data 00000400 00001000 00000002
This causes a timeout trying to bring up the GR ctx:
nouveau 0000:01:00.0: timeout
WARNING: CPU: 0 PID: 12 at drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.c:1547 gf100_grctx_generate+0x7b2/0x850 [nouveau]
Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET82W (1.55 ) 12/18/2018
Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
...
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: fifo: fault 01 [WRITE] at 0000000000008000 engine 00 [GR] client 15 [HUB/SCC_NB] reason c4 [] on channel -1 [0000000000 unknown]
The GPU never manages to recover. Booting without loading nouveau causes
issues as well, since the GPU starts sending spurious interrupts that cause
other device's IRQs to get disabled by the kernel:
irq 16: nobody cared (try booting with the "irqpoll" option)
...
handlers:
[<000000007faa9e99>] i801_isr [i2c_i801]
Disabling IRQ #16
...
serio: RMI4 PS/2 pass-through port at rmi4-00.fn03
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-110).
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
This causes the touchpad and sometimes other things to get disabled.
Since this happens without nouveau, we can't fix this problem from nouveau
itself.
Add a PCI quirk for the specific P50 variant of this GPU. Make sure the
GPU is advertising NoReset- so we don't reset the GPU when the machine is
in Dedicated graphics mode (where the GPU being initialized by the BIOS is
normal and expected). Map the GPU MMIO space and read the magic 0x2240c
register, which will have bit 1 set if the device was POSTed during a
previous boot. Once we've confirmed all of this, reset the GPU and
re-disable it - bringing it back to a healthy state.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203003
Link: https://lore.kernel.org/lkml/20190212220230.1568-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: nouveau@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
[bwh: Backported to 3.16:
- Use dev_{err,info}() instead of pci_{err,info}()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4cdd17ba1d upstream.
We need to compute the uart state only on the first open. This is
usually what is done in the ->install hook. serial_core used to do this
in ->open on every open. So move it to ->install.
As a side effect, it ensures the state is set properly in the window
after tty_init_dev is called, but before uart_open. This fixes a bunch
of races between tty_open and flush_to_ldisc we were dealing with
recently.
One of such bugs was attempted to fix in commit fedb576064 (serial:
fix race between flush_to_ldisc and tty_open), but it only took care of
a couple of functions (uart_start and uart_unthrottle). I was able to
reproduce the crash on a SLE system, but in uart_write_room which is
also called from flush_to_ldisc via process_echoes. I was *unable* to
reproduce the bug locally. It is due to having this patch in my queue
since 2012!
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 1 PID: 5 Comm: kworker/u4:0 Tainted: G L 4.12.14-396-default #1 SLE15-SP1 (unreleased)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c89-prebuilt.qemu.org 04/01/2014
Workqueue: events_unbound flush_to_ldisc
task: ffff8800427d8040 task.stack: ffff8800427f0000
RIP: 0010:uart_write_room+0xc4/0x590
RSP: 0018:ffff8800427f7088 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 000000000000002f RSI: 00000000000000ee RDI: ffff88003888bd90
RBP: ffffffffb9545850 R08: 0000000000000001 R09: 0000000000000400
R10: ffff8800427d825c R11: 000000000000006e R12: 1ffff100084fee12
R13: ffffc900004c5000 R14: ffff88003888bb28 R15: 0000000000000178
FS: 0000000000000000(0000) GS:ffff880043300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000561da0794148 CR3: 000000000ebf4000 CR4: 00000000000006e0
Call Trace:
tty_write_room+0x6d/0xc0
__process_echoes+0x55/0x870
n_tty_receive_buf_common+0x105e/0x26d0
tty_ldisc_receive_buf+0xb7/0x1c0
tty_port_default_receive_buf+0x107/0x180
flush_to_ldisc+0x35d/0x5c0
...
0 in rbx means tty->driver_data is NULL in uart_write_room. 0x178 is
tried to be dereferenced (0x178 >> 3 is 0x2f in rdx) at
uart_write_room+0xc4. 0x178 is exactly (struct uart_state *)NULL->refcount
used in uart_port_lock from uart_write_room.
So revert the upstream commit here as my local patch should fix the
whole family.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Li RongQing <lirongqing@baidu.com>
Cc: Wang Li <wangli39@baidu.com>
Cc: Zhang Yu <zhangyu31@baidu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: The previous fix didn't apply, so we don't need
to revert it here.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1bee2addc0 upstream.
In journal_reclaim() ja->cur_idx of each cache will be update to
reclaim available journal buckets. Variable 'int n' is used to count how
many cache is successfully reclaimed, then n is set to c->journal.key
by SET_KEY_PTRS(). Later in journal_write_unlocked(), a for_each_cache()
loop will write the jset data onto each cache.
The problem is, if all jouranl buckets on each cache is full, the
following code in journal_reclaim(),
529 for_each_cache(ca, c, iter) {
530 struct journal_device *ja = &ca->journal;
531 unsigned int next = (ja->cur_idx + 1) % ca->sb.njournal_buckets;
532
533 /* No space available on this device */
534 if (next == ja->discard_idx)
535 continue;
536
537 ja->cur_idx = next;
538 k->ptr[n++] = MAKE_PTR(0,
539 bucket_to_sector(c, ca->sb.d[ja->cur_idx]),
540 ca->sb.nr_this_dev);
541 }
542
543 bkey_init(k);
544 SET_KEY_PTRS(k, n);
If there is no available bucket to reclaim, the if() condition at line
534 will always true, and n remains 0. Then at line 544, SET_KEY_PTRS()
will set KEY_PTRS field of c->journal.key to 0.
Setting KEY_PTRS field of c->journal.key to 0 is wrong. Because in
journal_write_unlocked() the journal data is written in following loop,
649 for (i = 0; i < KEY_PTRS(k); i++) {
650-671 submit journal data to cache device
672 }
If KEY_PTRS field is set to 0 in jouranl_reclaim(), the journal data
won't be written to cache device here. If system crahed or rebooted
before bkeys of the lost journal entries written into btree nodes, data
corruption will be reported during bcache reload after rebooting the
system.
Indeed there is only one cache in a cache set, there is no need to set
KEY_PTRS field in journal_reclaim() at all. But in order to keep the
for_each_cache() logic consistent for now, this patch fixes the above
problem by not setting 0 KEY_PTRS of journal key, if there is no bucket
available to reclaim.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c9a78332b4 upstream.
If register_cache_set() failed, we would touch ca->set after
it had already been freed. Also, fix an assertion to catch
this.
Change-Id: I748e5f5b223e2d9b2602075dec2f997cced2394d
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 35d6fcbb7c upstream.
Do the proper cleanup in case the size check fails.
Tested with xfstests:generic/228
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 0cbade024b ("fuse: honor RLIMIT_FSIZE in fuse_file_fallocate")
Cc: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0cbade024b upstream.
fstests generic/228 reported this failure that fuse fallocate does not
honor what 'ulimit -f' has set.
This adds the necessary inode_newsize_ok() check.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Fixes: 05ba1f0823 ("fuse: add FALLOCATE operation")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9de5be06d0 upstream.
Writepage requests were cropped to i_size & 0xffffffff, which meant that
mmaped writes to any file larger than 4G might be silently discarded.
Fix by storing the file size in a properly sized variable (loff_t instead
of size_t).
Reported-by: Antonio SJ Musumeci <trapexit@spawn.link>
Fixes: 6eaf4782eb ("fuse: writepages: crop secondary requests")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 328e9f6973 upstream.
The error from snd_usb_mixer_apply_create_quirk() is ignored in the
current usb-audio driver code, which will continue the probing even
after the error. Let's take it more serious.
Fixes: 7b1eda223d ("ALSA: usb-mixer: factor out quirks")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6ae865615f upstream.
The __put_user() macro evaluates it's @ptr argument inside the
__uaccess_begin() / __uaccess_end() region. While this would normally
not be expected to be an issue, an UBSAN bug (it ignored -fwrapv,
fixed in GCC 8+) would transform the @ptr evaluation for:
drivers/gpu/drm/i915/i915_gem_execbuffer.c: if (unlikely(__put_user(offset, &urelocs[r-stack].presumed_offset))) {
into a signed-overflow-UB check and trigger the objtool AC validation.
Finish this commit:
2a418cf3f5 ("x86/uaccess: Don't leak the AC flag into __put_user() value evaluation")
and explicitly evaluate all 3 arguments early.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: luto@kernel.org
Fixes: 2a418cf3f5 ("x86/uaccess: Don't leak the AC flag into __put_user() value evaluation")
Link: http://lkml.kernel.org/r/20190424072208.695962771@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d4645d30b5 upstream.
The test robot reported a wrong assignment of a per-CPU variable which
it detected by using sparse and sent a report. The assignment itself is
correct. The annotation for sparse was wrong and hence the report.
The first pointer is a "normal" pointer and points to the per-CPU memory
area. That means that the __percpu annotation has to be moved.
Move the __percpu annotation to pointer which points to the per-CPU
area. This change affects only the sparse tool (and is ignored by the
compiler).
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: f97f8f06a4 ("smpboot: Provide infrastructure for percpu hotplug threads")
Link: http://lkml.kernel.org/r/20190424085253.12178-1-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6afb7e2697 upstream.
When using PCI passthrough with this device, the host machine locks up
completely when starting the VM, requiring a hard reboot. Add a quirk to
avoid bus resets on this device.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Link: https://lore.kernel.org/linux-pci/20190107213248.3034-1-james.prestwood@linux.intel.com
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c1ced46c7b upstream.
The ctrl_check_input() function is called from pvr2_ctrl_range_check().
It's supposed to validate user supplied input and return true or false
depending on whether the input is valid or not. The problem is that
negative shifts or shifts greater than 31 are undefined in C. In
practice with GCC they result in shift wrapping so this function returns
true for some inputs which are not valid and this could result in a
buffer overflow:
drivers/media/usb/pvrusb2/pvrusb2-ctrl.c:205 pvr2_ctrl_get_valname()
warn: uncapped user index 'names[val]'
The cptr->hdw->input_allowed_mask mask is configured in pvr2_hdw_create()
and the highest valid bit is BIT(4).
Fixes: 7fb20fa38c ("V4L/DVB (7299): pvrusb2: Improve logic which handles input choice availability")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 933c132084 upstream.
After removal of clock_start() from before soc_camera_init_i2c() in
soc_camera_probe() by commit 9aea470b39 ("[media] soc-camera: switch
I2C subdevice drivers to use v4l2-clk") introduced in v3.11, the ov6650
driver could no longer probe the sensor successfully because its clock
was no longer turned on in advance. The issue was initially worked
around by adding that missing clock_start() equivalent to OMAP1 camera
interface driver - the only user of this sensor - but a propoer fix
should be rather implemented in the sensor driver code itself.
Fix the issue by inserting a delay between the clock is turned on and
the sensor I2C registers are read for the first time.
Tested on Amstrad Delta with now out of tree but still locally
maintained omap1_camera host driver.
Fixes: 9aea470b39 ("[media] soc-camera: switch I2C subdevice drivers to use v4l2-clk")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4df2cb633b upstream.
Add an of_node_put() when a tested device node is not available.
Fixes: c026c98739 ("powerpc/83xx: Do not configure or probe disabled FSL DR USB controllers")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a147faa96f upstream.
This fixes the various compiler warnings when building the msgque
selftest. The primary change is using sys/msg.h instead of linux/msg.h
directly to gain the API declarations.
Fixes: 3a665531a3 ("selftests: IPC message queue copy feature test")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 767f015ea0 upstream.
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
arm32 xts-aes-neonbs doesn't set an alignmask, so currently it isn't
affected by this despite unconditionally accessing walk.iv. However
this is more subtle than desired, and it was actually broken prior to
the alignmask being removed by commit cc477bf645 ("crypto: arm/aes -
replace bit-sliced OpenSSL NEON code"). Thus, update xts-aes-neonbs to
start checking the return value of skcipher_walk_virt().
Fixes: e4e7f10bfc ("ARM: add support for bit sliced AES using NEON instructions")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit edaf28e996 upstream.
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
salsa20-generic doesn't set an alignmask, so currently it isn't affected
by this despite unconditionally accessing walk.iv. However this is more
subtle than desired, and it was actually broken prior to the alignmask
being removed by commit b62b3db76f ("crypto: salsa20-generic - cleanup
and convert to skcipher API").
Since salsa20-generic does not update the IV and does not need any IV
alignment, update it to use req->iv instead of walk.iv.
Fixes: 2407d60872 ("[CRYPTO] salsa20: Salsa20 stream cipher")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 98e2630284 upstream.
Currently the kfree of output.pointer can be potentially freeing
an uninitalized pointer in the case where out_data is NULL. Fix this
by reworking the case where out_data is not-null to perform the
ACPI status check and also the kfree of outpoint.pointer in one block
and hence ensuring the pointer is only freed when it has been used.
Also replace the if (ptr != NULL) idiom with just if (ptr).
Fixes: ff0e9f2628 ("platform/x86: alienware-wmi: Correct a memory leak")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a6d2a5a92e upstream.
Currently if alloc_skb fails to allocate the skb a null skb is passed to
t4_set_arp_err_handler and this ends up dereferencing the null skb. Avoid
the NULL pointer dereference by checking for a NULL skb and returning
early.
Addresses-Coverity: ("Dereference null return")
Fixes: b38a0ad8ec ("RDMA/cxgb4: Set arp error handler for PASS_ACCEPT_RPL messages")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 14b97ba5c2 upstream.
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 2219cd81a6 ("hwmon/vt1211: Add probing of alternate config index port")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e95fd518d0 upstream.
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: b72656dbc4 ("hwmon: (w83627hf) Stop using globals for I/O port numbers")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d6410408ad upstream.
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb14 ("I2C: Move hwmon drivers (2/3)")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8c08267567 upstream.
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb14 ("I2C: Move hwmon drivers (2/3)")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 755a9b0f8a upstream.
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: ba224e2c4f ("hwmon: New PC87427 hardware monitoring driver")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 73e6ff71a7 upstream.
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Unable to handle kernel paging request at virtual address ffffffbffee0002e
pgd = ffffffc1d68d4000
[ffffffbffee0002e] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 94000046 [#1] PREEMPT SMP
Modules linked in: f71805f(+) hwmon
CPU: 3 PID: 1659 Comm: insmod Not tainted 4.5.0+ #88
Hardware name: linux,dummy-virt (DT)
task: ffffffc1f6665400 ti: ffffffc1d6418000 task.ti: ffffffc1d6418000
PC is at f71805f_find+0x6c/0x358 [f71805f]
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple
drivers is synchronized.
Fixes: e53004e20a ("hwmon: New f71805f driver")
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reported-by: John Garry <john.garry@huawei.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d263119387 upstream.
Currently, compat tasks running on arm64 can allocate memory up to
TASK_SIZE_32 (UL(0x100000000)).
This means that mmap() allocations, if we treat them as returning an
array, are not compliant with the sections 6.5.8 of the C standard
(C99) which states that: "If the expression P points to an element of
an array object and the expression Q points to the last element of the
same array object, the pointer expression Q+1 compares greater than P".
Redefine TASK_SIZE_32 to address the issue.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jann Horn <jannh@google.com>
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
[will: fixed typo in comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c794d24ec9 upstream.
If module initialization fails after the character device has been
registered, unregister the character device. Additionally, avoid
duplicating error path code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Fixes: 6a03b4cd78 ("[SCSI] qla2xxx: Add char device to increase driver use count") # v2.6.35.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit dec3d0b107 upstream.
The ->digest() method of crct10dif-pclmul reads the current CRC value
from the shash_desc context. But this value is uninitialized, causing
crypto_shash_digest() to compute the wrong result. Fix it.
Probably this wasn't noticed before because lib/crc-t10dif.c only uses
crypto_shash_update(), not crypto_shash_digest(). Likewise,
crypto_shash_digest() is not yet tested by the crypto self-tests because
those only test the ahash API which only uses shash init/update/final.
Fixes: 0b95a7f857 ("crypto: crct10dif - Glue code to cast accelerated CRCT10DIF assembly as a crypto transform")
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 307508d107 upstream.
The ->digest() method of crct10dif-generic reads the current CRC value
from the shash_desc context. But this value is uninitialized, causing
crypto_shash_digest() to compute the wrong result. Fix it.
Probably this wasn't noticed before because lib/crc-t10dif.c only uses
crypto_shash_update(), not crypto_shash_digest(). Likewise,
crypto_shash_digest() is not yet tested by the crypto self-tests because
those only test the ahash API which only uses shash init/update/final.
This bug was detected by my patches that improve testmgr to fuzz
algorithms against their generic implementation.
Fixes: 2d31e518a4 ("crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework")
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 742b06b562 upstream.
We hit a BUG at fs/buffer.c:3057 if we detached the nbd device
before unmounting ext4 filesystem.
The typical chain of events leading to the BUG:
jbd2_write_superblock
submit_bh
submit_bh_wbc
BUG_ON(!buffer_mapped(bh));
The block device is removed and all the pages are invalidated. JBD2
was trying to write journal superblock to the block device which is
no longer present.
Fix this by checking the journal superblock's buffer head prior to
submitting.
Reported-by: Eric Ren <renzhen@linux.alibaba.com>
Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4ec73791a6 upstream.
Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode
(conventional PCI on primary side, PCIe on downstream side), the Retrain
Link bit needs to be cleared manually to allow the link training to
complete successfully.
If it is not cleared manually, the link training is continuously restarted
and no devices below the PCI-to-PCIe bridge can be accessed. That means
drivers for devices below the bridge will be loaded but won't work and may
even crash because the driver is only reading 0xffff.
See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for
details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL,
PI7C9X130.
Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected
devices set this bit.
Note that pcie_retrain_link() lives in aspm.c because that's currently the
only place we use it, but this erratum is not specific to ASPM, and we may
retrain links for other reasons in the future.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
[bhelgaas: apply regardless of CONFIG_PCIEASPM]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bwh: Backported to 3.16:
- Use dev_info() instead of pci_info()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 86fa6a3442 upstream.
Factor out pcie_retrain_link() to use for Pericom Retrain Link quirk. No
functional change intended.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c8f191282f upstream.
pr->tx_bytes should be assigned to tx_bytes other than
rx_bytes.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: ce45b87302 ("ehea: Fixing statistics")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c48cadf5bf upstream.
The mentioned function pointer is long gone since early 2011. Remove the
reference in the comment and reword it slightly.
Fixes: 51ba60c5bb ("RTC: Cleanup rtc_class_ops->update_irq_enable()")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5cbdae10bf upstream.
Commit e6f77540c0 ("scsi: qla2xxx: Fix an integer overflow in sysfs
code") incorrectly set 'optrom_region_size' to 'start+size', which can
overflow option-rom boundaries when 'start' is non-zero. Continue setting
optrom_region_size to the proper adjusted value of 'size'.
Fixes: e6f77540c0 ("scsi: qla2xxx: Fix an integer overflow in sysfs code")
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 65a102f680 upstream.
For each enabled crtc the functions sets dpms on all registered connectors.
Limit this to only doing it once and on the connectors actually in use.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Fixes: 023eb571a1 ("drm: correctly update connector DPMS status in drm_fb_helper")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326175546.18126-3-noralf@tronnes.org
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7649773293 upstream.
The use of zero-sized array causes undefined behaviour when it is not
the last member in a structure. As it happens to be in this case.
Also, the current code makes use of a language extension to the C90
standard, but the preferred mechanism to declare variable-length
types such as this one is a flexible array member, introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last. Which is beneficial
to cultivate a high-quality code.
Fixes: e48f129c2f ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c03a0fd0b6 upstream.
syzbot is hitting use-after-free bug in uinput module [1]. This is because
kobject_uevent(KOBJ_REMOVE) is called again due to commit 0f4dafc056
("Kobject: auto-cleanup on final unref") after memory allocation fault
injection made kobject_uevent(KOBJ_REMOVE) from device_del() from
input_unregister_device() fail, while uinput_destroy_device() is expecting
that kobject_uevent(KOBJ_REMOVE) is not called after device_del() from
input_unregister_device() completed.
That commit intended to catch cases where nobody even attempted to send
"remove" uevents. But there is no guarantee that an event will ultimately
be sent. We are at the point of no return as far as the rest of the kernel
is concerned; there are no repeats or do-overs.
Also, it is not clear whether some subsystem depends on that commit.
If no subsystem depends on that commit, it will be better to remove
the state_{add,remove}_uevent_sent logic. But we don't want to risk
a regression (in a patch which will be backported) by trying to remove
that logic. Therefore, as a first step, let's avoid the use-after-free bug
by making sure that kobject_uevent(KOBJ_REMOVE) won't be triggered twice.
[1] https://syzkaller.appspot.com/bug?id=8b17c134fe938bbddd75a45afaa9e68af43a362d
Reported-by: syzbot <syzbot+f648cfb7e0b52bf7ae32@syzkaller.appspotmail.com>
Analyzed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 0f4dafc056 ("Kobject: auto-cleanup on final unref")
Cc: Kay Sievers <kay@vrfy.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9c2ccc324b upstream.
Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen"
can copy up to 255 bytes and we only have room for two bytes. Even
if this comes from the firmware and we trust it, the new policy
generally is just to fix it as kernel hardenning.
I can't test this code so I tried to be very conservative. I considered
not allowing "evt_hdr->dlen == 1" because it doesn't initialize the
whole variable but in the end I decided to allow it and manually
initialized "asic_id" and "asic_ver" to zero.
Fixes: e8454ff7b9 ("[media] drivers:media:radio: wl128x: FM Driver Common sources")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0e633f9716 upstream.
clang warns about a possible variable use that gcc never
complained about:
drivers/media/platform/davinci/isif.c:982:32: error: variable 'frame_size' is uninitialized when used here
[-Werror,-Wuninitialized]
dm365_vpss_set_pg_frame_size(frame_size);
^~~~~~~~~~
drivers/media/platform/davinci/isif.c:887:2: note: variable 'frame_size' is declared here
struct vpss_pg_frame_size frame_size;
^
1 error generated.
There is no initialization for this variable at all, and there
has never been one in the mainline kernel, so we really should
not put that stack data into an mmio register.
On the other hand, I suspect that gcc checks the condition
more closely and notices that the global
isif_cfg.bayer.config_params.test_pat_gen flag is initialized
to zero and never written to from any code path, so anything
depending on it can be eliminated.
To shut up the clang warning, just remove the dead code manually,
it has probably never been used because any attempt to do so
would have resulted in undefined behavior.
Fixes: 63e3ab142f ("V4L/DVB: V4L - vpfe capture - source for ISIF driver on DM365")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7f0d078667 upstream.
Commit 747834ab83 ("ARM: OMAP2+: hwmod: revise hardreset behavior") made
the call to _enable() conditional based on no oh->rst_lines_cnt. This
caused the return value to be potentially uninitialized. Curiously we see
no compiler warnings for this, probably as this gets inlined.
We call _setup_reset() from _setup() and only _setup_postsetup() if the
return value is zero. Currently the return value can be uninitialized for
cases where oh->rst_lines_cnt is set and HWMOD_INIT_NO_RESET is not set.
Fixes: 747834ab83 ("ARM: OMAP2+: hwmod: revise hardreset behavior")
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 608f729c31 upstream.
Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA
memory in get_fw_boot_info() but attempt to free it anyway:
drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (!(val & 0x07)) {
^~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here
dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma);
^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true
if (!(val & 0x07)) {
^~~~~~~~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning
dma_addr_t buf_dma;
^
= 0
Skip the call to dma_free_coherent() here.
Fixes: 2a991c2159 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b00ef53053 upstream.
It must be made sure that immediate mode is not already set, when
modifying shadow register value in ehrpwm_pwm_disable(). Otherwise
modifications to the action-qualifier continuous S/W force
register(AQSFRC) will be done in the active register.
This may happen when both channels are being disabled. In this case,
only the first channel state will be recorded as disabled in the shadow
register. Later, when enabling the first channel again, the second
channel would be enabled as well. Setting RLDCSF to zero, first, ensures
that the shadow register is updated as desired.
Fixes: 38dabd91ff ("pwm: tiehrpwm: Fix disabling of output of PWMs")
Signed-off-by: Christoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
[vigneshr@ti.com: Improve commit message]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ef4bb63dc1 upstream.
We forgot to set "ret" on this error path.
Fixes: e8454ff7b9 ("[media] drivers:media:radio: wl128x: FM Driver Common sources")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b7ed69d67f upstream.
Fix the interrupt information for the GPIO lines with a shared EINT
interrupt.
Fixes: 16d7ff2642 ("ARM: dts: add dts files for exynos5260 SoC")
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7afb0df554 upstream.
We should be updating *pos. The current code is a no-op.
Fixes: 1c1e45d17b ("V4L/DVB (7786): cx18: new driver for the Conexant CX23418 MPEG encoder chip")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
