Enable sun6i DMA engine, sun6i P2WI, PWM, and crypto engine (Security
System) drivers by default. EXTCON is needed by the updated sun4i USB
PHY driver.
While at it, enable FHANDLE, which is needed by systemd and newer
versions of udev. Also enable CGROUPS for systemd.
And get rid of POWER_RESET, as the sun6i power reset driver has been
removed in favor of proper sun6i watchdog support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This tablet has proper USB OTG support, using 3 GPIO pins for
ID and VBUS detection, and also VBUS control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The tablet has volume up/down buttons on the side, connected to the LRADC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the Ippo Q8H-A33 tablet, for now it
is enabled in host-only mode, because true OTG support requires support
for detecting and enabling Vbus through the axp221 pmic.
For this to work the Vbus on the port must be enabled by u-boot,
or a powered hub must be used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the A13 OLinuxIno.
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the A10s OLinuxIno Micro.
Note the A10s OlinuxIno Micro always has some voltage on its otg power
pin, even if the usb-vbus0-regulator is disabled, the leaked voltage is
enough to make vbus-det always report 1, so we do not use vbus-det on
this board.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 4b3dc9679c ("arm64: force CONFIG_SMP=y and remove redundant #ifdefs")
accidentally retained code for !CONFIG_SMP in cpu_resume function. This
resulted in the hash index being zeroed in x7 after proper computation,
which is then used to get the cpu context pointer while resuming.
This patch removes the remanant code and restores back the cpu suspend/
resume functionality.
Fixes: 4b3dc9679c ("arm64: force CONFIG_SMP=y and remove redundant #ifdefs")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This reverts commit b9855f03d5.
The patch break existing DMA usage case. For example, audio SOC
dmaengine never release channel and cause virt-dma to cache too
much memory in descriptor to exhaust system memory.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 6f166312c6 ("dmaengine: mv_xor: add support for a38x command
in descriptor mode") introduced the support for a feature that
appeared in Armada 38x: specifying the operation to be performed in a
per-descriptor basis rather than globally per channel.
However, when doing so, it changed the function mv_chan_set_mode() to
use:
if (IS_ENABLED(__BIG_ENDIAN))
instead of:
#if defined(__BIG_ENDIAN)
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler. Consequently, the commit broke support for big-endian,
as the XOR_DESCRIPTOR_SWAP flag was not set in the XOR channel
configuration register.
The primarily visible effect was some nasty warnings and failures
appearing during the self-test of the XOR unit:
[ 1.197368] mv_xor d0060900.xor: error on chan 0. intr cause 0x00000082
[ 1.197393] mv_xor d0060900.xor: config 0x00008440
[ 1.197410] mv_xor d0060900.xor: activation 0x00000000
[ 1.197427] mv_xor d0060900.xor: intr cause 0x00000082
[ 1.197443] mv_xor d0060900.xor: intr mask 0x000003f7
[ 1.197460] mv_xor d0060900.xor: error cause 0x00000000
[ 1.197477] mv_xor d0060900.xor: error addr 0x00000000
[ 1.197491] ------------[ cut here ]------------
[ 1.197513] WARNING: CPU: 0 PID: 1 at ../drivers/dma/mv_xor.c:664 mv_xor_interrupt_handler+0x14c/0x170()
See also:
http://storage.kernelci.org/next/next-20150617/arm-mvebu_v7_defconfig+CONFIG_CPU_BIG_ENDIAN=y/lab-khilman/boot-armada-xp-openblocks-ax3-4.txt
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 6f166312c6 ("dmaengine: mv_xor: add support for a38x command in descriptor mode")
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is an overlap in dma ring cmd csr region due to sharing of ethernet
ring cmd csr region. This patch fix the resource overlapping by mapping
the entire dma ring cmd csr region.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the missing update of the transfer data width in
at_xdmac_prep_slave_sg().
Indeed, for each item in the scatter-gather list, we check whether the
transfer length is aligned with the data width provided by
dmaengine_slave_config(). If so, we directly use this data width for the
current part of the transfer we are preparing. Otherwise, the data width
is reduced to 8 bits (1 byte). Of course, the actual number of register
accesses must also be updated to match the new data width.
So one chunk was missing in the original patch (see Fixes tag below): the
number of register accesses was correctly set to (len >> fixed_dwidth) in
mbr_ubc but the real data width was not updated in mbr_cfg. Since mbr_cfg
may change for each part of the scatter-gather transfer this also explains
why the original patch used the Descriptor View 2 instead of the
Descriptor View 1.
Let's take the example of a DMA transfer to write 8bit data into an Atmel
USART with FIFOs. When FIFOs are enabled in the USART, its Transmit
Holding Register (THR) works in multidata mode, that is to say that up to
4 8bit data can be written into the THR in a single 32bit access and it is
still possible to write only one data with a 8bit access. To take
advantage of this new feature, the DMA driver was modified to allow
multiple dwidths when doing slave transfers.
For instance, when the total length is 22 bytes, the USART driver splits
the transfer into 2 parts:
First part: 20 bytes transferred through 5 32bit writes into THR
Second part: 2 bytes transferred though 2 8bit writes into THR
For the second part, the data width was first set to 4_BYTES by the USART
driver thanks to dmaengine_slave_config() then at_xdmac_prep_slave_sg()
reduces this data width to 1_BYTE because the 2 byte length is not aligned
with the original 4_BYTES data width. Since the data width is modified,
the actual number of writes into THR must be set accordingly.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 6d3a7d9e3a ("dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers")
Cc: stable@vger.kernel.org #4.0 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As claimed by the programmer datasheet and confirmed by the IP designer,
the Block Transfer Size (BTSIZE) bitfield of the Channel x Control A
Register (CTRLAx) always refers to a number of Source Width (SRC_WIDTH)
transfers.
Both the SRC_WIDTH and BTSIZE bitfields can be extacted from the CTRLAx
register to compute the DMA residue. So the 'tx_width' field is useless
and can be removed from the struct at_desc.
Before this patch, atc_prep_slave_sg() was not consistent: BTSIZE was
correctly initialized according to the SRC_WIDTH but 'tx_width' was always
set to reg_width, which was incorrect for MEM_TO_DEV transfers. It led to
bad DMA residue when 'tx_width' != SRC_WIDTH.
Also the 'tx_width' field was mostly set only in the first and last
descriptors. Depending on the kind of DMA transfer, this field remained
uninitialized for intermediate descriptors. The accurate DMA residue was
computed only when the currently processed descriptor was the first or the
last of the chain. This algorithm was a little bit odd. An accurate DMA
residue can always be computed using the SRC_WIDTH and BTSIZE bitfields
in the CTRLAx register.
Finally, the test to check whether the currently processed descriptor is
the last of the chain was wrong: for cyclic transfer, last_desc->lli.dscr
is NOT equal to zero, since set_desc_eol() is never called, but logically
equal to first_desc->txd.phys. This bug has a side effect on the
drivers/tty/serial/atmel_serial.c driver, which uses cyclic DMA transfer
to receive data. Since the DMA residue was wrong each time the DMA
transfer reaches the second (and last) period of the transfer, no more
data were received by the USART driver till the cyclic DMA transfer loops
back to the first period.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Torsten Fleischer <torfl6749@gmail.com>
Tested-by: Jirí Prchal <jiri.prchal@aksignal.cz>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using descriptor view 2 or higher, we don't write the configuration
into AT_XDMAC_CC register because this configuration will be fetch from
the descriptor. Unfortunately, the PROT bit is not updated with this
method, we have to do it manually before enabling the channel.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
testusb.c at http://www.linux-usb.org/usbtest/ is out of date,
using the one at the kernel source folder.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch replace dynamicly allocated luns array with static one.
This simplifies the code of mass storage function and modules.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
To enable sharing of the arm_pmu code with arm64, this patch factors it
out to drivers/perf/. A new drivers/perf directory is added for
performance monitor drivers to live under.
MAINTAINERS is updated accordingly. Files added previously without a
corresponsing MAINTAINERS update (perf_regs.c, perf_callchain.c, and
perf_event.h) are also added.
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: augmented Kconfig help slightly]
Signed-off-by: Will Deacon <will.deacon@arm.com>
arch_find_n_match_cpu_physical_id parses the device tree to get the
device node for a given logical cpu index. However, since ARM PMUs get
probed after the CPU device nodes are stashed while registering the
cpus, we can use of_cpu_device_node_get to avoid another DT parse.
This patch replaces arch_find_n_match_cpu_physical_id with
of_cpu_device_node_get to reuse the stashed value directly instead.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On systems containing multiple, heterogeneous clusters we need a way to
associate a PMU "device" with the CPU(s) on which it exists. For PMUs
that signal overflow with SPIs, this relationship is determined via the
"interrupt-affinity" property, which contains a list of phandles to CPU
nodes for the PMU. For PMUs using PPIs, the per-cpu nature of the
interrupt isn't enough to determine the set of CPUs which actually
contain the device.
This patch allows the interrupt-affinity property to be specified on a
PMU node irrespective of the interrupt type. For PPIs, it identifies
the set of CPUs signalling the PPI in question.
Tested-by: Stephen Boyd <sboyd@codeaurora.org> # Krait PMU
Signed-off-by: Will Deacon <will.deacon@arm.com>
For PPI based PMUs, we bail out early in of_pmu_irq_cfg() without
setting the PMU's supported_cpus bitmap. This causes the
smp_call_function_any() in armv7_probe_num_events() to fail. Set
the bitmap to be all CPUs so that we properly probe PMUs that use
PPIs.
Fixes: cc88116da0 ("arm: perf: treat PMUs as CPU affine")
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add missing return value check. In case of error print debug message
and return error code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since maxpacket_limit was introduced all UDC drivers should use
usb_ep_set_maxpacket_limit() function instead of setting maxpacket value
manually. ep.maxpacket_limit contains actual maximum maxpacket value
supported by hardware which is needed by epautoconf.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since maxpacket_limit was introduced all UDC drivers should use
usb_ep_set_maxpacket_limit() function instead of setting maxpacket value
manually. ep.maxpacket_limit contains actual maximum maxpacket value
supported by hardware which is needed by epautoconf.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function midi registers two interfaces with single set_alt() function
which means that f_midi_set_alt() is called twice when configuration
is set. That means that endpoint initialization and ep request allocation
is done two times. To avoid this problem we do such things only once,
for interface number 1 (MIDI Streaming interface).
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Function ffs_do_functionfs_bind() calls functionfs_bind() which allocates
usb request and increments refcounts. These things needs to be cleaned
up by if further steps of initialization fail by calling functionfs_unbind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With the grouping of multi-function devices a non-ATS
capable device might also end up in the same domain as an
IOMMUv2 capable device.
So handle this situation gracefully and don't consider it a
bug anymore.
Tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch fix some typos found in a printk message and
MODULE_DESCRIPTION.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least on the AM335x, enabling OMAP_I2C_SYSTEST_ST_EN is not enough to
allow direct access to the SCL and SDA pins. In addition to ST_EN, we
need to set the TMODE to 0b11 (Loop back & SDA/SCL IO mode select).
Also, as the reset values of SCL_O and SDA_O are 0 (which means "drive
low level"), we need to set them to 1 (which means "high-impedance") to
avoid unwanted changes on the pins.
As a precaution, reset all these bits to their default values after
recovery is complete.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using set_scl may be ineffective before calling the driver specific
prepare_recovery callback, which might change into a test mode. So
instead of setting SCL in i2c_generic_scl_recovery, move it to
i2c_generic_recovery (after the optional prepare_recovery).
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The change removes redundant sysfs binary file boundary check, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The change removes redundant sysfs binary file boundary checks,
since this task is already done on caller side in fs/sysfs/file.c
Note, on file size overflow read() now returns 0, and this is a
correct and expected EOF notification according to POSIX.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it clearer that this is the pointer to the userspace vm86
state area.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438148483-11932-8-git-send-email-brgerst@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
vm86.h was being implicitly included in alot of places via
processor.h, which in turn got it from math_emu.h. Break that
chain and explicitly include vm86.h in all files that need it.
Also remove unused vm86 field from math_emu_info.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438148483-11932-7-git-send-email-brgerst@gmail.com
[ Fixed build failure. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move vm86 specific definitions from irq_vectors.h to vm86.h.
Based on patch from Brian Gerst.
Originally-from: Brian Gerst <brgerst@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438148483-11932-6-git-send-email-brgerst@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Change to use the normal pt_regs area to enter and exit vm86
mode. This is done by increasing the padding at the top of the
stack to make room for the extra vm86 segment slots in the IRET
frame. It then saves the 32-bit regs in the off-stack vm86
data, and copies in the vm86 regs. Exiting back to 32-bit mode
does the reverse. This allows removing the hacks to jump
directly into the exit asm code due to having to change the
stack pointer. Returning normally from the vm86 syscall and the
exception handlers allows things like ptrace and auditing to work properly.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438148483-11932-5-git-send-email-brgerst@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now there is no vm86-specific data left on the kernel stack
while in userspace, except for the 32-bit regs.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438148483-11932-4-git-send-email-brgerst@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Allocate a separate structure for the vm86 fields.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1438148483-11932-2-git-send-email-brgerst@gmail.com
[ Build fixes. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The test failed due to an oversight on my part when run on a
64-bit kernel. vm86 isn't expected to work at all, and I
mistakenly failed one part of the test because no signal was
delivered.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/502c8bef877b33fe4943885ded6125dfcc7892db.1438205722.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The modify_ldt syscall exposes a large attack surface and is
unnecessary for modern userspace. Make it optional.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: security@kernel.org <security@kernel.org>
Cc: xen-devel <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/a605166a771c343fd64802dece77a903507333bd.1438291540.git.luto@kernel.org
[ Made MATH_EMULATION dependent on MODIFY_LDT_SYSCALL. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, we detect whether the SMMU has coherent page table walk
capability from the IDR0.CTTW field, and base our cache maintenance
decisions on that. In preparation for fixing the bogus DMA API usage,
however, we need to ensure that the DMA API agrees about this, which
necessitates deferring to the dma-coherent property in the device tree
for the final say.
As an added bonus, since systems exist where an external CTTW signal
has been tied off incorrectly at integration, allowing DT to override
it offers a neat workaround for coherency issues with such SMMUs.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If the StreamIDs in a system can all be resolved by a single level-2
stream table (i.e. SIDSIZE < SPLIT), then we currently get our maths
wrong and allocate the largest strtab we support, thanks to unsigned
overflow in our calculation.
This patch fixes the issue by checking the SIDSIZE explicitly when
calculating the size of our first-level stream table.
Reported-by: Matt Evans <matt.evans@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The MSI memory attributes in the SMMUv3 driver are from an older
revision of the spec, which doesn't match the current implementations.
Out with the old, in with the new.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When an ARM SMMUv3 instance supports PRI, the driver registers
an interrupt handler, but fails to enable the generation of
such interrupt at the SMMU level.
This patches simply moves the enable flags to a variable that
gets updated by the PRI handling code before being written to the
SMMU register.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When using Edgeport/416 models with newer firmware (sometime after
firmware version 4.80.0), idle ports are automatically bounced
(disconnected and then reconnected) approximately every 60 seconds.
This breaks programs (e.g: minicom) where idle periods are common,
normal and expected.
I confirmed with the manufacturer (Digi International) that Edgeport/416
models now ship from the factory with firmware that expects periodic
"heartbeat" queries from the driver to keep idle ports alive. This
patch implements heartbeat support using the mechanism Digi suggested
(periodically requesting an I2C descriptor address) that appears effective
on Edgeports running the newer firmware (that require it) and benign on
Edgeport devices running older firmware. Since we know that Edgeport
firmware version 4.80 (the version distributed in /lib/firmware/down3.bin
and used for Edgeports that are either running still older versions or
have no onboard non-volatile firmware image) does not require heartbeat
support, this patch schedules heartbeats only on Edgeport/416 devices,
and only if they are running firmware versions newer than 4.80.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
[johan: minor style changes ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Do what we can to verify that the driver's firmware image is valid
(before attempting to download it to the Edgeport) by adding a new
function, check_fw_sanity(), and a call to it in in download_fw().
Note: It looks like some Edgeports (models like the EP/416 with on-board
E2PROM) may be able to function even if the on-disk firmware image is
bad or missing, iff their local E2PROM versions are valid. But most
Edgeport models (I've tried EP/1 and EP/8) do not appear to have this
capability and they always rely on the on-disk firmware image.
I tested an implementation that calls the new check_fw_sanity()
function at the top of download_fw() and, rather than simply returning
an error if the firmware image is bad or missing, it saves the result
and defers the decision until later when it may find that it is running
on a E2PROM-equipped device with a valid image. But I think this is
messier than it is worth (adding still more messiness to the already
very messy download_fw()) for such a marginal possible benefit. So, at
least for now, I have chosen the much simpler approach of returning an
error whenever edge_startup() fails to load an on-disk firmware image, or
check_fw_sanity() indicates that it is unusable.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
[johan: drop redundant checksum mask ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Enable the otg/drc usb controller on the A10 OLinuxIno Lime.
Signed-off-by: Remy van Elst <relst@relst.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
