Assign GPIO chip owner field to chip->dev->driver->owner if it was not
configured by GPIO driver.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now nothing prevents GPIO driver from being unloaded if its gpios
were requested as GPIO IRQs only (without calling gpio_request()).
Hence, add calls of try_module_get()/module_put() into
gpiochip_irq_reqres/relres() to track such scenario properly.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We've been moving all omap2+ based systems to boot in device tree only
mode for a few years now. Only omap3 has legacy booting support
remaining. Most omap3 boards already have related arch/arm/boot/*.dts*
files for booting with device tree.
This board has support for device tree based booting, and we've been
printing warnings about the legacy booting being deprecated for a
few merge cycles now. Let's attempt to remove the legacy booting
for it.
The reason for removing the legacy booting support now rather than
later is we can simply revert this patch if necessary if we run
into some unexpected issues that are not trivial to fix for the
device tree based booting.
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This laptop needs GPIO4 pulled high to enable the headphone amplifier,
and has a mute LED on GPIO3. I modelled the patch on the existing
GPIO4 code which pulls the line low for the same purpose; this time,
the HP amp line is pulled high.
v2: Disable the headphone amplifier when no headphone is connected.
Don't disable power savings to preserve the LED state.
v3: Remove headset-specific hooks and code; this is just a headphone.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the removal of the r8a7740 legacy SoC code in commit
44d88c754e ("ARM: shmobile: Remove legacy SoC code for R-Mobile
A1"), r8a7740 is only supported in generic DT-only ARM multi-platform
builds. The driver doesn't need to match platform devices by name
anymore, hence remove the corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the removal of the r8a7740 legacy SoC code in commit
44d88c754e ("ARM: shmobile: Remove legacy SoC code for R-Mobile
A1"), r8a7740 is only supported in generic ARM multi-platform builds.
Hence CONFIG_ARCH_MULTIPLATFORM is always set, and the check can be
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the removal of the sh73a0 legacy SoC code in commit
9a9863987b ("ARM: shmobile: Remove legacy SoC code for SH-Mobile
AG5"), sh73a0 is only supported in generic DT-only ARM multi-platform
builds. The driver doesn't need to match platform devices by name
anymore, hence remove the corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the removal of the sh73a0 legacy SoC code in commit
9a9863987b ("ARM: shmobile: Remove legacy SoC code for SH-Mobile
AG5"), sh73a0 is only supported in generic ARM multi-platform builds.
Hence CONFIG_ARCH_MULTIPLATFORM is always set, and the check can be
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pin function controller (which can be a GPIO controller) is
instantiated before the interrupt controllers, due to the ordering in
the DTS, the irq domains for the interrupt controllers referenced by its
"interrupts-extended" property cannot be found yet:
irq: no irq domain found for /interrupt-controller@e61c0000 !
As the sh-pfc driver accesses the platform device's resources directly,
it cannot find the (optional) IRQ resources, and thinks no interrupts
are available. This may lead to failures later, when GPIOs are used as
interupts:
gpio-keys keyboard: Unable to claim irq 0; error -22
gpio-keys: probe of keyboard failed with error -22
To fix this, add support for deferred probing to sh-pfc, by converting
the driver from direct platform device resource access to using the
platform_get_resource() and platform_get_irq() helpers.
Note that while this fixes the root cause worked around by commit
e4ba0a9bdd ("ARM: shmobile: r8a73a4: Move pfc node to work around
probe ordering bug"), I strongly recommend against reverting the
workaround now, as this would lead to lots of probe deferrals in drivers
relying on pinctrl. This may be reconsidered once the DT code starts
taking into account phandle dependencies during device instantation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The "function", "pins" and "groups" pinmux and pinctrl properties have
been standardized. Support them in addition to the custom "renesas,*"
properties. New-style and old-style properties can't be mixed in DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This really doesn't seem to have much chance of working anymore,
esp for irq context, qxl at least tries to talk to the hw,
and waits for irqs, and fails.
with runtime pm and other stuff I think we should just
bail on this for now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's add a minimal clocks for dm814x to get it booted. This is
mostly a placeholder and relies on the PLLs being on from the
bootloader.
Note that the divider clocks work the same way as on dm816x and
am335x.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looking at the TI kernel tree I noticed that dm81xx need custom
ti81xx_pwrdm_operations. Let's also change dm816x over to use them
as the registers are different for dm81xx compared to others.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For now, let's just add the ones shared with dm816x.
The dm814x specific ones can be added as they are tested.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes for compilation warnings and errors reported by Kbuild test robot
for x86_64 and i386.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the removal of the r8a7740 legacy board code in commit
1fa59bda21 ("ARM: shmobile: Remove legacy board code for
Armadillo-800 EVA"), all former users of the "sh_fsi2" platform device
name are only supported in generic DT-only ARM multi-platform builds.
The driver doesn't need to match platform devices by name anymore, hence
remove the corresponding platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spinlock 'slock' is used now to protect pcf857x_irq() from itself
which is unnecessary (especially after switching to use threaded
IRQs). Hence, remove it and use mutex to protect device data in IRQ
handler.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio registercannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DFLL clocksource was missing from the list of possible parents for
the fast CPU cluster. Add it to the list.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Save and restore this register since the LP1 restore assembly routines
fiddle with it. Otherwise the CPU would keep running on PLLX after
resume from suspend even when DFLL was the original clocksource.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add basic platform driver support for the fast CPU cluster DFLL
clocksource found on Tegra124 SoCs. This small driver selects the
appropriate Tegra124-specific characterization data and integration
code. It relies on the DFLL common code to do most of the work.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
[treding@nvidia.com: move setup code into ->probe()]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The offset of the first spare bit register on Tegra210 is 0x380, but
account for the fixed offset of 0x100 in the fuse accessor.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The offset of the first spare bit register on Tegra124 is 0x300, but
account for the fixed offset of 0x100 in the fuse accessor.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The offset of the first spare bit register on Tegra114 is 0x280, but
account for the fixed offset of 0x100 in the fuse accessor.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There's a mixture of core_* and soc_* prefixes for variables storing
information related to the VDD_CORE rail. Choose one (soc_*) and use it
more consistently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unifying the drivers makes it easier to restrict the legacy probing
paths to 32-bit ARM. This in turn will come in handy as support for
new 64-bit ARM SoCs is added.
Signed-off-by: Thierry Reding <treding@nvidia.com>
For backwards-compatibility with old device trees, if no APBMISC node
exists this driver hard-codes the I/O memory region. All 64-bit ARM
device tree files are recent enough that they can be required to have
this node, and therefore the legacy code path is not required.
Based on work done by Paul Walmsley <pwalmsley@nvidia.com>.
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 uses a power management controller that is compatible with
earlier SoC generations but adds a couple of power partitions for new
hardware blocks.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For backwards-compatibility with old device trees, if no PMC node exists
this driver hard-codes the I/O memory region. All 64-bit ARM device tree
files are recent enough that they can be required to have this node, and
therefore the legacy code path is not required on 64-bit ARM.
Based on work done by Paul Walmsley <pwalmsley@nvidia.com>.
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make sure to only drop the reference to the OF node after it's been
successfully obtained.
Fixes: 3568df3d31 ("soc: tegra: Add thermal reset (thermtrip) support to PMC")
Cc: <stable@vger.kernel.org> # v4.0+
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since commit 59032702ea ("ARM: shmobile: Remove legacy platform
devices from EMEV2 SoC code"), EMMA Mobile SoCs are only supported in
generic DT-only ARM multi-platform builds. The driver doesn't need to
use platform data anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Niklas Söderlund <niso@kth.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Checkpatch.pl complains about these:
WARNING: Possible unnecessary 'out of memory' message
The messages use a little extra RAM and they add a few extra lines of
code. We're probably never going to hit these out of memory situations
but if we did then kmalloc() has pretty good error messages built-in.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We were allocating enough space because sizeof("-grp") and
sizeof("-mux") are both equal to 5 but in the snprintf() we only allowed
for 4 characters so the last 'p' and 'x' characters were truncated.
The allocate and sprintf can be done in one step with the kasprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
M25P80 driver provides support for most common SPI NOR devices.
These devices are commonly found on TI EVMs for AM437x and DRA7x
SoCs.
Enable support for this driver in defconfig for omap2plus devices.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CPTS module of CPSW IP enables timestamp synchronization
using PTP. Enable CPTS feature of CPSW driver.
Available on AM335x, AM437x and DRA7x SoCs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for on-chip resistive touchscreen m found on AM335x and
AM437x devices.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for on-chip ADC found on AM335x and
AM437x devices.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to ease testing, expose the list of supported EMC frequencies
via debugfs.
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The example in the device tree binding documentation and the driver code
list hda2codec_2x as the last entry in the clock-names and reset-names
properties. Update the description of the properties to use the same
order.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix hda2codec_2x clock and reset names in Tegra30 HDA controller device
tree node documentation. While at it also fix coma vs. semicolon issue.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
