delete useless 'break' after 'return'.
let 'return 0' instead of 'return (0)'
also give a comment for 'break' to let readers notice it.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to make sure sprites are disabled before shutting off a pipe.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The full dynticks feature only shows up when all its
Kconfig dependencies are met (RCU nocbs, RCU user mode, ...)
This is far from being user friendly as those who want to
activate this feature need to look into the Kconfig files
and iterate through each dependency then activate these
by hand in order to show and select the full dynticks
Kconfig option.
So process the other way around: show up the Kconfig option
if the minimal low level dependencies are met and activate
the high level ones when we enable the feature.
Note there is one exception in the picture:
CONFIG_VIRT_CPU_ACCOUNTING_GEN is part of a Kconfig choice
menu and it appears we can't select it from another Kconfig
selection when it's under such layout. So for now this
particular item stays as a passive dependency.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
currently cbq works incorrectly for limits > 10% real link bandwidth,
and practically does not work for limits > 50% real link bandwidth.
Below are results of experiments taken on 1 Gbit link
In shaper | Actual Result
-----------+---------------
100M | 108 Mbps
200M | 244 Mbps
300M | 412 Mbps
500M | 893 Mbps
This happen because of q->now changes incorrectly in cbq_dequeue():
when it is called before real end of packet transmitting,
L2T is greater than real time delay, q_now gets an extra boost
but never compensate it.
To fix this problem we prevent change of q->now until its synchronization
with real time.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Reviewed-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No constant alpha yet though, that needs a new ioctl and/or property to
get/set.
v2: use drm_plane_format_cpp (Ville)
fix up vlv_disable_plane, remove IVB bits (Ville)
remove error path rework (Ville)
fix component order confusion (Ville)
clean up platform init (Ville)
use compute_offset_xtiled (Ville)
v3: fix up more format confusion (Ville)
update to new page offset function (Ville)
v4: remove incorrect formats from framebuffer_init (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
warning: 'pf_info.max_tx_ques' may be used uninitialized in this function
[-Wmaybe-uninitialized]
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix for smatch tool reported error
drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c:2029
qlcnic_probe() error: potential NULL dereference 'adapter'.
o While returning from an error path in probe, adapter is not
initialized. So do not access adapter in cleanup path.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[net-next:master 301/302] drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.c:563
qlcnic_set_multi() error: potential null dereference 'cur'. (kzalloc returns null)
o Break out of the loop after memory allocation failure. Program all the
MAC addresses that were cached in the return path.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a declaration left over from the TCPCT-ectomy. This sysctl is
no longer referenced anywhere since 1a2c6181c4 ("tcp: Remove TCPCT").
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we couldn't find a pipe we shouldn't return true. This might be even
better as a WARN though, since it should be impossible to have the port
enabled without a pipe selected.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we couldn't find a pipe we shouldn't return true. This might be even
better as a WARN though, since it should be impossible to have the port
enabled without a pipe selected.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Modifying the clock sources (via the DREF control on the PCH) is a slow
multi-stage process as we need to let the clocks stabilise between each
stage. If we are not actually changing the clock sources, then we can
return early.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Appease checkpatch by deleting a space after a ~]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On the at91_adc a minimal Sample and Hold Time is necessary for the ADC to
guarantee the best converted final value between two channels selection.
This time has to be programmed through the bitfield SHTIM in the
Mode Register ADC_MR.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The sleep mode will allow to put the adc in sleep between conversion.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
at91 adc offers the choice between two resolutions: low and high.
The low and high resolution values depends on adc IP version, as many IP
properties have been exposed through device tree, these settings have also
been added to the dt bindings.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
More and more sub-architectures are using only the irqchip_init
function. Make the core code call this function if no init_irq field is
provided in the machine description to remove some boilerplate code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Occassionaly on a DL380 G4 the guest would crash quite early with this:
(XEN) d244:v0: unhandled page fault (ec=0003)
(XEN) Pagetable walk from ffffffff84dc7000:
(XEN) L4[0x1ff] = 00000000c3f18067 0000000000001789
(XEN) L3[0x1fe] = 00000000c3f14067 000000000000178d
(XEN) L2[0x026] = 00000000dc8b2067 0000000000004def
(XEN) L1[0x1c7] = 00100000dc8da067 0000000000004dc7
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 244 (vcpu#0) crashed on cpu#3:
(XEN) ----[ Xen-4.1.3OVM x86_64 debug=n Not tainted ]----
(XEN) CPU: 3
(XEN) RIP: e033:[<ffffffff81263f22>]
(XEN) RFLAGS: 0000000000000216 EM: 1 CONTEXT: pv guest
(XEN) rax: 0000000000000000 rbx: ffffffff81785f88 rcx: 000000000000003f
(XEN) rdx: 0000000000000000 rsi: 00000000dc8da063 rdi: ffffffff84dc7000
The offending code shows it to be a loop writting the value zero
(%rax) in the %rdi (the L4 provided by Xen) register:
0: 44 00 00 add %r8b,(%rax)
3: 31 c0 xor %eax,%eax
5: b9 40 00 00 00 mov $0x40,%ecx
a: 66 0f 1f 84 00 00 00 nopw 0x0(%rax,%rax,1)
11: 00 00
13: ff c9 dec %ecx
15:* 48 89 07 mov %rax,(%rdi) <-- trapping instruction
18: 48 89 47 08 mov %rax,0x8(%rdi)
1c: 48 89 47 10 mov %rax,0x10(%rdi)
which fails. xen_setup_kernel_pagetable recycles some of the Xen's
page-table entries when it has switched over to its Linux page-tables.
Right before try to clear the page, we make a hypercall to change
it from _RO to _RW and that works (otherwise we would hit an BUG()).
And the _RW flag is set for that page:
(XEN) L1[0x1c7] = 001000004885f067 0000000000004dc7
The error code is 3, so PFEC_page_present and PFEC_write_access, so page is
present (correct), and we tried to write to the page, but a violation
occurred. The one theory is that the the page entries in hardware
(which are cached) are not up to date with what we just set. Especially
as we have just done an CR3 write and flushed the multicalls.
This patch does solve the problem by flusing out the TLB page
entry after changing it from _RO to _RW and we don't hit this
issue anymore.
Fixed-Oracle-Bug: 16243091 [ON OCCASIONS VM START GOES INTO
'CRASH' STATE: CLEAR_PAGE+0X12 ON HP DL380 G4]
Reported-and-Tested-by: Saar Maoz <Saar.Maoz@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This avoids any other hardirq handler seeing a very stale jiffies
value immediately after wakeup from a long idle period. The one
observable symptom of this was a USB keyboard, with software keyboard
repeat, which would always repeat a key immediately that it was
pressed. This is due to the key press waking the guest, the key
handler immediately runs, sees an old jiffies value, and then that
jiffies value significantly updated, before the key is unpressed.
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Keir Fraser <keir.fraser@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'gic' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
irqchip: gic: Call handle_bad_irq() directly
arm: Move chained_irq_(enter|exit) to a generic file
arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
+ Linux 3.9-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch register the dma controller with generic dma helpers only
in DT case. This also adds some extra error handling in the driver.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reported-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Issues raised in last series to propose this have now been resolved
so there should be no reason this driver cannot graduate from staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Now the mysterious NOSTART flag is gone from the read, we can use the
i2c_smbus_read_byte/word/i2c_block_data functions instead of the
local reimplementation of these standard functions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
This flag makes no sense whatsoever where it is.
Documentation/i2c/i2c-protocol states:
If you set the I2C_M_NOSTART variable for the first partial message,
we do not generate Addr, but we do generate the startbit S. This will
probably confuse all other clients on your bus, so don't try this.
This is exactly what is going on here. Likelihood given that the
driver never checked for this protocol mangling being available is that
it wasn't present on the test boards and hence this flag was simply
ignored. No indication of why it would be necessary has been found in
the datasheets.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reentrancy into the clock framework is necessary for clock operations
that result in nested calls to the clk api. A common example is a clock
that is prepared via an i2c transaction, such as a clock inside of a
discrete audio chip or a power management IC. The i2c subsystem itself
will use the clk api resulting in a deadlock:
clk_prepare(audio_clk)
i2c_transfer(..)
clk_prepare(i2c_controller_clk)
The ability to reenter the clock framework prevents this deadlock.
Other use cases exist such as allowing .set_rate callbacks to call
clk_set_parent to achieve the best rate, or to save power in certain
configurations. Yet another example is performing pinctrl operations
from a clk_ops callback. Calls into the pinctrl subsystem may call
clk_{un}prepare on an unrelated clock. Allowing for nested calls to
reenter the clock framework enables both of these use cases.
Reentrancy is implemented by two global pointers that track the owner
currently holding a global lock. One pointer tracks the owner during
sleepable, mutex-protected operations and the other one tracks the owner
during non-interruptible, spinlock-protected operations.
When the clk framework is entered we try to hold the global lock. If it
is held we compare the current task against the current owner; a match
implies a nested call and we reenter. If the values do not match then
we block on the lock until it is released.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Cc: David Brown <davidb@codeaurora.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Create locking helpers for the global mutex and global spinlock. The
definitions of these helpers will be expanded upon in the next patch
which introduces reentrancy into the locking scheme.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Rajagopal Venkat <rajagopal.venkat@linaro.org>
Cc: David Brown <davidb@codeaurora.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch finally adds the WM8850 SoC to the multi_v7_defconfig.
We don't have a seperate defconfig for this SoC as it is only
available as a multiplatform option.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Convert AMD erratum 400 to the bug infrastructure. Then, retract all
exports for modules since they're not needed now and make the AMD
erratum checking machinery local to amd.c. Use forward declarations to
avoid shuffling too much code around needlessly.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1363788448-31325-7-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Convert the AMD erratum 383 testing code to the bug infrastructure. This
allows keeping the AMD-specific erratum testing machinery private to
amd.c and not export symbols to modules needlessly.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1363788448-31325-6-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We add another 32-bit vector at the end of the ->x86_capability
bitvector which collects bugs present in CPUs. After all, a CPU bug is a
kind of a capability, albeit a strange one.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1363788448-31325-2-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make sure that msg pointer is set back to error value in case of
MSG_COPY flag is set and desired message to copy wasn't found. This
garantees that msg is either a error pointer or a copy address.
Otherwise the last message in queue will be freed without unlinking from
the queue (which leads to memory corruption) and the dummy allocated
copy won't be released.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for USB host
pins.
CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY device.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>