When older variants of the HREF (earlier than v22) development
platform enter suspend mode, power down EXT_SUPPLY1.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If particular platforms require non-standard initialisation values,
they can use this function to adapt them as required.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass constraint information for recently supported external AB8500
controlled regulators. Also change the start-up initialisation settings
for each of the 3 supported external supplies to low-power, off and
high-power for supply 1, 2 and 3 respectively.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ABx500 is capable of controlling three external regulator supplies.
Most commonly on and off are supported, but if an external regulator
chipset or power supply supports high-power and low-power mode settings,
we can control those too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't treat it as an error if a partition is already in the same power
state when a user wants to power it on or off. This allows code to
proceed if no state change is required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This function can be used by drivers to enable power to the hardware
blocks that they drive. Most of the drivers can be built as a module
and therefore require this function to be exported.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This properly sets the modes of the sysfs files.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Clark Williams <williams@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9214d1d8 set the USB persist flag as a default for all devices.
This might be desirable for some distributions, but it certainly has its
trade-offs... most importantly, it can significantly increase system
resume time, because the kernel blocks on resuming (and sometimes
resetting) USB devices before it unfreezes userspace.
This patch introduces a new config option CONFIG_USB_DEFAULT_PERSIST,
which allows distributions to make this decision on their own without
the need to carry a custom patch or revert the kernel's setting in
userspace.
[edited the Kconfig help text a bit - gregkh]
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DMA support, The received data is not pushed to tty until the DMA buffer
is filled. But some megabyte rate chips such as BT expect fast response and
data should be pushed immediately. In order to fix this issue, We suggest
the use of the timer for polling DMA buffer.
In our test, no data loss occurred at high-baudrate as compared with interrupt-
driven (We tested with 3Mbps).
We changes:
- We add timer for polling. If we set poll_timer to 10, every 10ms,
timer handler checks the residue in the dma buffer and transfer data
to the tty. Also, last_residue is updated for the next polling.
- poll_timeout is used to prevent the timer's system cost.
If poll_timeout is set to 3000 and no data is received in 3 seconds,
we inactivate poll timer and driver falls back to interrupt-driven.
When data is received again in FIFO and UART irq is occurred, we switch
back to DMA mode and start polling.
- We use consistent DMA mappings to avoid from the frequent cache operation
of the timer function for default.
- pl011_dma_rx_chars is modified. the pending size is recalculated because
data can be taken by polling.
- the polling time is adjusted if dma rx poll is enabled but no rate is
specified. Ideal polling interval to push 1 character at every interval
is the reciprocal of 'baud rate / 10 line bits per character / 1000 ms
per sec'. But It is very aggressive to system. Experimentally,
'10000000 / baud' is suitable to receive dozens of characters. the poll rate
can be specified statically by dma_rx_poll_rate of the platform data as well.
Changes compared to v1:
- Use of consistent DMA mappings.
- Added dma_rx_poll_rate in platform data to specify the polling interval.
- Added dma_rx_poll_timeout in platform data to specify the polling timeout.
Changes compared to v2:
- Use of consistent DMA mappings for default.
- Added dma_rx_poll_enable in platform data to adjust the polling time
according to the baud rate.
- remove unnecessary lock from the polling function.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For percpu notes, we are exporting only address and not size. So
the userspace tool kexec-tools is putting an upper limit of 1024
and putting the value in p_memsz and p_filesz fields. So the patch
add the new sysfile crash_notes_size to export the exact percpu
note size and let the kexec-tools parse it intead of using 1024.
The idea came from Vivek Goyal. And a later patch will be sent to
kexec-tools to let it parse the size.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 21d8a15a (lookup_one_len: don't accept . and ..) reiserfs
started failing to delete xattrs from inode. This was due to a buggy
test for '.' and '..' in fill_with_dentries() which resulted in passing
'.' and '..' entries to lookup_one_len() in some cases. That returned
error and so we failed to iterate over all xattrs of and inode.
Fix the test in fill_with_dentries() along the lines of the one in
lookup_one_len().
Reported-by: Pawel Zawora <pzawora@gmail.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Until recently uio_get_minor() returned 0 for success and
a negative value on failure. This became non-negative for suceess and
negative for failure. Restore the original return value spec so that we can
successfully initialize UIO devices with a non-zero minor device
number.
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If memory hot-add fails with the error -EEXIST, then this is a permanent
failure. Notify the host of this information, so the host will not attempt
hot-add again. If the failure were a transient failure, host will attempt
a hot-add after some delay.
In this version of the patch, I have added some additional comments
to clarify how the host treats different failure conditions.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Hyper-V it will be very efficient to use 2M allocations in the guest as this
makes the ballooning protocol with the host that much more efficient. Hyper-V
uses page ranges (start pfn : number of pages) to specify memory being moved
around and with 2M pages this encoding can be very efficient. However, when
memory is returned to the guest, the host does not guarantee any granularity.
To deal with this issue, split the page soon after a successful 2M allocation
so that this memory can potentially be freed as 4K pages.
If 2M allocations fail, we revert to 4K allocations.
In this version of the patch, based on the feedback from Michal Hocko
<mhocko@suse.cz>, I have added some additional commentary to the patch
description.
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This symbol will be used in the Hyper-V balloon driver to support 2M
allocations.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Windows hosts permit the guest to specify memory hot-add alignment
requirements (if any). Linux currently requires a 128MB alignment on memory
segments that can be hot-added. Specify this alignment requirement to the
host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/misc/apds990x.c:1205:12: warning: 'apds990x_suspend' defined but not used [-Wunused-function]
drivers/misc/apds990x.c:1214:12: warning: 'apds990x_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/misc/bh1770glc.c:1314:12: warning: 'bh1770_suspend' defined but not used [-Wunused-function]
drivers/misc/bh1770glc.c:1324:12: warning: 'bh1770_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/misc/bh1780gli.c:200:12: warning: 'bh1780_suspend' defined but not used [-Wunused-function]
drivers/misc/bh1780gli.c:222:12: warning: 'bh1780_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MEI drivers should be able to carry their private data around.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define a truly synchronous API for the bus Tx path by putting all pending
request to the write list and wait for the interrupt tx handler to wake
us up.
The ___mei_cl_send() out path is also slightly reworked to make it look more
like main.c:mei_write().
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register the MEI bus type against the kernel core bus APIs and
call the bus Rx handler from interrupt.c
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We keep track of all MEI devices on the bus through a specific linked list.
We also have a mei_device instance in the mei_cl structure.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mapping as follows:
E_RANGE -> ERANGE
E_UNDEF -> ENODATA
E_TOOLONG -> E2BIG
SET_DEFAULT -> ERESTART
As a side effect it fixes a bug in spk_var_store() where return code was
mistakenly compared to negative value instead of positive.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have simple_strtoul and simple_strtol. Don't repeat their functionality
here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) A nice little removal of the unwanted private pointer from
struct iio_trigger.
2) Some clean up of the ad799x driver.
3) Couple of cleanups for the exynos_adc driver and some documentation.
4) Move the mxs-lradc initialization a little earlier in the driver to avoid
wiping out the configuration just after setting it.
A nice small set of worthy bits and bobs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=20Ps
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.10b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second round of IIO cleanups for the 3.10 cycle
1) A nice little removal of the unwanted private pointer from
struct iio_trigger.
2) Some clean up of the ad799x driver.
3) Couple of cleanups for the exynos_adc driver and some documentation.
4) Move the mxs-lradc initialization a little earlier in the driver to avoid
wiping out the configuration just after setting it.
A nice small set of worthy bits and bobs.
mei client bus will present some of the mei clients
as devices for other standard subsystems
Implement the probe, remove, match, device addtion routines, along with
the sysfs and uevent ones. mei_cl_device_id is also added to
mod_devicetable.h
A mei-cleint-bus.txt document describing the rationale and the API usage
is also added while ABI/testing/sysfs-bus-mei describeis the modalias ABI.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei layer provides host bus message layer, client management,
and os interface
mei-me - provides access to ME hardware through
the pci bus
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hw initialization is now done as part of
hw specific code this makes the name mei_hw_init little misleading.
We rename it to mei_start in spirit of already existing
functions mei_stop and mei_reset.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mei_timer and mei_host_client_init belongs to mei framework
and are not ME hw specific.
AMTHIF and WD are available only for ME but are above the hardware layer
so move the initialization back from mei_me_dev_init to mei_device_init.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
we need to unregister watchdog device both in suspend and remove
as the registration is recreated on reset
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ECOVERING_FROM_RESET device state is never set
we can remove it
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pci/shuah-defines:
iommu/amd: Remove calc_devid() and use PCI_DEVID() from PCI
iommu/amd: Remove local PCI_BUS() define and use PCI_BUS_NUM() from PCI
PCI/AER: Remove local PCI_BUS() define and use PCI_BUS_NUM() from PCI
PCI: Add PCI_BUS_NUM() and PCI_DEVID() interfaces
Loading the cypress firmware is not dvb specific and should be common
functionality. Move the source to media/common and make it a standalone
module.
As a result we can remove the dependency on dvb-usb in go7007, which has
nothing to do with dvb.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user reported a panic where we were panicing somewhere in
tree_backref_for_extent from scrub_print_warning. He only captured the trace
but looking at scrub_print_warning we drop the path right before we mess with
the extent buffer to print out a bunch of stuff, which isn't right. So fix this
by dropping the path after we use the eb if we need to. Thanks,
Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Masterkit MA901 usb radio device shares USB ID with Atmel V-USB devices.
This patch adds additional checks in usb_ma901radio_probe() and if
product or manufacturer doesn't match we return -ENODEV and don't
continue. This allows hid drivers to handle not MA901 device.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch reverts commit 0322bd3980 ("usb hid quirks for Masterkit MA901 usb
radio") and adds checks in hid_ignore() for Masterkit MA901 usb radio device.
This usb radio device shares USB ID with many Atmel V-USB (and probably other)
devices so patch sorts things out by checking name, vendor, product of hid device.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
vidioc_s_tuner, vidioc_s_frequency and vidioc_s_register now
uses a constant argument. So, the driver reports warnings:
drivers/media/radio/radio-si476x.c:1196:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/media/radio/radio-si476x.c:1196:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_tuner') [enabled by default]
drivers/media/radio/radio-si476x.c:1199:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/media/radio/radio-si476x.c:1199:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_frequency') [enabled by default]
drivers/media/radio/radio-si476x.c:1209:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/media/radio/radio-si476x.c:1209:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_register') [enabled by default]
This is due to a (soft) merge conflict, as both this driver and the
const patches were applied for the same Kernel version.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds a driver that exposes all the radio related
functionality of the Si476x series of chips via the V4L2 subsystem.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a base to be used for allocation of all the SI476X specific
controls in the corresponding driver.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>