This commit introduces new class of standard controls
V4L2_CTRL_CLASS_FM_RX. This class is intended to all controls
pertaining to FM receiver chips. Also, two controls belonging to said
class are added as a part of this commit: V4L2_CID_TUNE_DEEMPHASIS and
V4L2_CID_RDS_RECEPTION.
This patch is based on the code found in the patch by Manjunatha Halli [1]
[1] http://lists-archives.com/linux-kernel/27641307-new-control-class-and-features-for-fm-rx.html
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the type of V4L2_CID_TUNE_PREEMPHASIS from 'integer' to 'enum
v4l2_preemphasis'
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds all necessary header files and Kbuild plumbing for the
core driver for Silicon Laboratories Si476x series of AM/FM tuner
chips.
The driver as a whole is implemented as an MFD device and this patch
adds a core portion of it that provides all the necessary
functionality to the two other drivers that represent radio and audio
codec subsystems of the chip.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds code related to manipulation of the properties of
SI476X chips.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds main part(out of three) of the I2C driver for the
"core" of MFD device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds all the functions used for exchanging commands with
the chip.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On powerpc the maximum size for the ioctl argument is 8191, and it was
8192. However, the 64x64 array of threshold values is more than is actually
needed in practice for PAL and NTSC formats. A 45x45 array will do just fine.
So change the size accordingly to fix this problem.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If i run verbose v4l2-compliance with my radio-mr800 device few times
then i get warning about frequency out of range:
root@machine:~# v4l2-compliance -r /dev/radio0 -v 2
is radio
Driver Info:
Driver name : radio-mr800
Card type : AverMedia MR 800 USB FM Radio
Bus info : usb-0000:00:1a.0-1.2
Driver version: 3.9.0
Capabilities : 0x80050400
Tuner
Radio
Device Capabilities
Device Caps : 0x00050400
Tuner
Radio
Compliance test for device /dev/radio0 (not using libv4l2):
Required ioctls:
test VIDIOC_QUERYCAP: OK
Allow for multiple opens:
test second radio open: OK
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
Debug ioctls:
test VIDIOC_DBG_G_CHIP_IDENT: OK (Not Supported)
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
test VIDIOC_LOG_STATUS: OK
Input ioctls:
test VIDIOC_G/S_TUNER: OK
warn: v4l2-test-input-output.cpp(234): returned tuner 0 frequency out
of range (6550200 not in [1400000...1728000])
test VIDIOC_G/S_FREQUENCY: OK
test VIDIOC_S_HW_FREQ_SEEK: OK
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 0 Audio Inputs: 0 Tuners: 1
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0
Control ioctls:
info: checking v4l2_queryctrl of control 'User Controls' (0x00980001)
info: checking v4l2_queryctrl of control 'Mute' (0x00980909)
info: checking v4l2_queryctrl of control 'Mute' (0x00980909)
test VIDIOC_QUERYCTRL/MENU: OK
info: checking control 'User Controls' (0x00980001)
info: checking control 'Mute' (0x00980909)
test VIDIOC_G/S_CTRL: OK
info: checking extended control 'User Controls' (0x00980001)
info: checking extended control 'Mute' (0x00980909)
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
info: checking control event 'User Controls' (0x00980001)
info: checking control event 'Mute' (0x00980909)
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 2 Private Controls: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_PRESETS: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
Format ioctls:
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported)
test VIDIOC_G/S_PARM: OK (Not Supported)
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK (Not Supported)
test VIDIOC_TRY_FMT: OK (Not Supported)
test VIDIOC_S_FMT: OK (Not Supported)
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
Codec ioctls:
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls:
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported)
Total: 38, Succeeded: 38, Failed: 0, Warnings: 1
Some printk() debugging showed that vidioc_s_hw_freq_seek() setups
radio->curfreq to out of range value (lines 395-396) and calls
amradio_set_freq() to set this frequency on device without any
out-of-range checks.
Patch protects from setting up frequency on device to incorrect value
moving clamp_t check inside amradio_set_freq. With this patch we can
call amradio_set_freq() with out of range frequency from any place.
Also put comment that sometimes radio->curfreq is set to out of range
value in vidioc_s_hw_freq_seek().
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The et61x251 driver was removed in v3.5. Remove the last references to
its Kconfig macro now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the code to use devm_* API so that driver core will manage
resources.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since we have generic i2c bus recover routines now, these custom ones
need to be renamed to fix the namespace clash. Proper conversion needs
to be done by someone who has access to the hardware.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and
others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for
resolutions higher than 640x480, further driver changes will be necessary,
such as sensor output resolution switching (including further configuration
changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats
at high resolutions. Image quality should also needs to be improved.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver also probes at least two further i2c addresses (0x22 >> 1
and 0x66 >> 1). I've got some hints that they are very likely used by Samsung
and Kodak sensors, which are known to be used in Empia devices, too.
We havn't seen any devices using these sensors yet and don't know how to probe
them properly, so leave a comment.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OmniVision sensors are used as well in Empiatech based cameras such as the
"SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640).
With this patch applied, OminiVision sensors with 8 bit address and register
width are detected (recent models have a 16 bit address width and use different
client addresses).
The most commonly used sensors (including the ones listed by Empiatech) are
detected properly, although there is no support for them yet.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Other sensors like the ones from OmniVision need a different probing procedure,
so it makes sense have separate functions for each manufacturer/sensor type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add further Micron chip IDs to be able to identify all Micron sensors listed
by Empiatech.
Also probe the two alternate i2c addresses used by Micron sensors with 8 bit
address and 16 bit register width.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx-cards.c is very large and the sensor/camera related code is growing,
so move this code to a separate source code file em28xx-camera.c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the board hints and the sensor initialization/configuration have been
separated, em28xx_detect_sensor() is the better name for this function.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sensor detection and initialization/configuration are currently mixed together.
This works as long as all devices with a particular sensor are working with the
same board configuration. In the long run, this will be not sufficient, so
separate these both steps to make the code more flexible and future proof.
This also makes the code more consistent, because the initialization of the
MT9V011 sensor subdevice is already separated.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exynos ADC won't work without a regulator called "vdd" and a clock
called "adc". Document this fact in the device tree bindings.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current board hint code is mixed together with the sensor detection and
initialization code. It actually selects a board depending on the detected
sensor type only, with the result that 3 of the 6 webcam boards are currently
dead.
Separate it and move it to em28xx_hint_board() which already contains the board
hints for analog capturing+TV and DVB devices.
This way, we have all board hints at a common place which makes it easier
to extend the code and reduces the risk of regressions.
It also makes it possible again to use the boards EM2750_BOARD_DLCW_130,
EM2820_BOARD_VIDEOLOGY_20K14XUSB and EM2860_BOARD_NETGMBH_CAM (using the module
parameter "card").
NOTE: the current board hint logic for webcams is preserved. Not more not less.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to initialize hardware before registering the touchscreen. Else,
we end up setting registers in mxs_lradc_ts_open(), getting called just
after registering the touchscreen with input_register_device() and by
the end of mxs_lradc_probe(), we reset the LRADC block hence losing the
correct configuration.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Fixes some typos in the documentation of exynos-adc.txt.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
exynos_adc is a DT only driver and exynos_adc_match table is always
compiled in. Hence remove the macro.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Avoid allocating and freeing the sample buffer for each transfer. Instead
allocate it once when we start sampling. Also pre-compute the number of bytes we
need to transfer in the same way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver has support for reporting a channels scale, but none of the channels
set the IIO_CHAN_INFO_SCALE mask. Add the IIO_CHAN_INFO_SCALE to all channels to
indicate that the drivers supports reporting the scale.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ad779x channels all follow the same pattern. Add a helper macro to
initialize the channel spec, this allows us to drop quite a few lines.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use i2c_smbus_{read,write}_word_data_swapped instead of open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
None of the devices supported by this driver have an internal voltage reference,
so remove support for it from the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove fields from the ad799x_state struct which are not used.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We previously relied on the bootloader to do the muxing of the UART for
the Cubieboard. Don't rely on it anymore and use pinctrl.
Also remove uart1, as it is not enabled by default and it's not exposed
on the board headers.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We previously relied on the bootloader to do the muxing of the UART for
the Hackberry. Don't rely on it anymore and use pinctrl.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
The Allwinner A10 SoC has 8 available UARTs, which is 6 more than on the
A13, so add the missing UARTs to the sun4i-a10 dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Both A10 and A13 Allwinner SoCs have a Synopsys APB uart3 device
available, so add it to the sunxi.dtsi file
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
The UART0 is only available on the Allwinner A10 SoCs, and not on the
A13, so move the uart0 node to sun4i-a10.dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Tested-by: Emilio López <emilio@elopez.com.ar>
The other architecture use serial@address for their uart nodes, so
rename our uart dt nodes to be consistent
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It will be especially useful when we will have the clock definitions in
the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Tested-by: Emilio López <emilio@elopez.com.ar>
This patch fixes a regression introduced in v3.8-rc1 code where a failed
target_check_reservation() check in target_setup_cmd_from_cdb() was causing
an incorrect SAM_STAT_GOOD status to be returned during a WRITE operation
performed by an unregistered / unreserved iscsi initiator port.
This regression is only effecting iscsi-target due to a special case check
for TCM_RESERVATION_CONFLICT within iscsi_target_erl1.c:iscsit_execute_cmd(),
and was still correctly disallowing WRITE commands from backend submission
for unregistered / unreserved initiator ports, while returning the incorrect
SAM_STAT_GOOD status due to the missing SAM_STAT_RESERVATION_CONFLICT
assignment.
This regression was first introduced with:
commit de103c93af
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
Go ahead and re-add the missing SAM_STAT_RESERVATION_CONFLICT assignment
during a target_check_reservation() failure, so that iscsi-target code
sends the correct SCSI status.
All other fabrics using target_submit_cmd_*() with a RESERVATION_CONFLICT
call to transport_generic_request_failure() are not effected by this bug.
Reported-by: Jeff Leung <jleung@curriegrad2004.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a VHOST_SCSI_FEATURES mask minus VIRTIO_RING_F_EVENT_IDX
so that vhost-scsi-pci userspace will strip this feature bit once
GET_FEATURES reports it as being unsupported on the host.
This is to avoid a bug where ->handle_kicks() are missed when EVENT_IDX
is enabled by default in userspace code.
(mst: Rename to VHOST_SCSI_FEATURES + add comment)
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Op 23-03-13 12:47, Peter Hurley schreef:
> On Tue, 2013-03-19 at 11:13 -0400, Peter Hurley wrote:
>> On vanilla 3.9.0-rc3, I get this 100% repeatable oops after login when
>> the user X session is coming up:
> Perhaps I wasn't clear that this happens on every boot and is a
> regression from 3.8
>
> I'd be happy to help resolve this but time is of the essence; it would
> be a shame to have to revert all of this for 3.9
Well it broke on my system too, so it was easy to fix.
I didn't even need gdm to trigger it!
>8----
This fixes regression caused by 1d7c71a3e2 (drm/nouveau/disp: port vblank handling to event interface),
which causes a oops in the following way:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
IP: [<0000000000000001>] 0x0
PGD 0
Oops: 0010 [#1] PREEMPT SMP
Modules linked in: ip6table_filter ip6_tables ebtable_nat ebtables ...<snip>...
CPU 3
Pid: 0, comm: swapper/3 Not tainted 3.9.0-rc3-xeon #rc3 Dell Inc. Precision WorkStation T5400 /0RW203
RIP: 0010:[<0000000000000001>] [<0000000000000001>] 0x0
RSP: 0018:ffff8802afcc3d80 EFLAGS: 00010087
RAX: ffff88029f6e5808 RBX: 0000000000000001 RCX: 0000000000000000
RDX: 0000000000000096 RSI: 0000000000000001 RDI: ffff88029f6e5808
RBP: ffff8802afcc3dc8 R08: 0000000000000000 R09: 0000000000000004
R10: 000000000000002c R11: ffff88029e559a98 R12: ffff8802a376cb78
R13: ffff88029f6e57e0 R14: ffff88029f6e57f8 R15: ffff88029f6e5808
FS: 0000000000000000(0000) GS:ffff8802afcc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000001 CR3: 000000029fa67000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper/3 (pid: 0, threadinfo ffff8802a355e000, task ffff8802a3535c40)
Stack:
ffffffffa0159d8a 0000000000000082 ffff88029f6e5820 0000000000000001
ffff88029f71aa00 0000000000000000 0000000000000000 0000000004000000
0000000004000000 ffff8802afcc3e38 ffffffffa01843b5 ffff8802afcc3df8
Call Trace:
<IRQ>
[<ffffffffa0159d8a>] ? nouveau_event_trigger+0xaa/0xe0 [nouveau]
[<ffffffffa01843b5>] nv50_disp_intr+0xc5/0x200 [nouveau]
[<ffffffff816fbacc>] ? _raw_spin_unlock_irqrestore+0x2c/0x50
[<ffffffff816ff98d>] ? notifier_call_chain+0x4d/0x70
[<ffffffffa017a105>] nouveau_mc_intr+0xb5/0x110 [nouveau]
[<ffffffffa01d45ff>] nouveau_irq_handler+0x6f/0x80 [nouveau]
[<ffffffff810eec95>] handle_irq_event_percpu+0x75/0x260
[<ffffffff810eeec8>] handle_irq_event+0x48/0x70
[<ffffffff810f205a>] handle_fasteoi_irq+0x5a/0x100
[<ffffffff810182f2>] handle_irq+0x22/0x40
[<ffffffff8170561a>] do_IRQ+0x5a/0xd0
[<ffffffff816fc2ad>] common_interrupt+0x6d/0x6d
<EOI>
[<ffffffff810449b6>] ? native_safe_halt+0x6/0x10
[<ffffffff8101ea1d>] default_idle+0x3d/0x170
[<ffffffff8101f736>] cpu_idle+0x116/0x130
[<ffffffff816e2a06>] start_secondary+0x251/0x258
Code: Bad RIP value.
RIP [<0000000000000001>] 0x0
RSP <ffff8802afcc3d80>
CR2: 0000000000000001
---[ end trace 907323cb8ce6f301 ]---
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If there are no channels, chan would never end up being NULL,
and so the null pointer check would fail.
Solve this by initializing chan to NULL, and iterating over temp instead.
Fixes oops when running intel-gpu-tools/tests/kms_flip, which attempts to
do some intel ioctl's on a nouveau device.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org [3.7+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This reverts commit 1869305009 ("mm: introduce VM_POPULATE flag to
better deal with racy userspace programs").
VM_POPULATE only has any effect when userspace plays racy games with
vmas by trying to unmap and remap memory regions that mmap or mlock are
operating on.
Also, the only effect of VM_POPULATE when userspace plays such games is
that it avoids populating new memory regions that get remapped into the
address range that was being operated on by the original mmap or mlock
calls.
Let's remove VM_POPULATE as there isn't any strong argument to mandate a
new vm_flag.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit implements support for using the clk api; this lets us use
the "clocks" property with device tree, instead of having to use
clock-frequency.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>