Introduce timer polling method to MCAN since some SoCs may not
have M_CAN interrupt routed to A53 Linux and do not have
interrupt property in device tree M_CAN node.
On AM62x SoC, MCANs on MCU domain do not have hardware interrupt
routed to A53 Linux, instead they will use timer polling method.
Add an hrtimer to MCAN class device. Each MCAN will have its own
hrtimer instantiated if there is no hardware interrupt found in
device tree M_CAN node. The timer will generate a software
interrupt every 1 ms. In hrtimer callback, we check if there is
a transaction pending by reading a register, then process by
calling the isr if there is.
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Verdin AM62
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/all/20230707204714.62964-3-jm@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On AM62x SoC, MCANs on MCU domain do not have hardware interrupt
routed to A53 Linux, instead they will use software interrupt by
timer polling.
To enable timer polling method, interrupts should be
optional so remove interrupts property from required section and
add an example for MCAN node with timer polling enabled.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/all/20230707204714.62964-2-jm@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a fix for the Zen2 VZEROUPPER data corruption bug where under
certain circumstances executing VZEROUPPER can cause register
corruption or leak data.
The optimal fix is through microcode but in the case the proper
microcode revision has not been applied, enable a fallback fix using
a chicken bit.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmSvvRAACgkQaA3BHVML
eiNpGQgAs8jq1XjN9t8jZsdgXnoCbkZyVUI2NO0HwoVwpRCLgbXp5AX5qq2oRciE
TBhe4Fceh/ZsYqHTZQahnguxgRKM5JgXwbI4Z0iiOVcqasNbycaKAqipxJJ7kdo1
qPhGCbgQFVX7oIq2xjfXehh6O0SYX+R9r88X8dMJxMYv/pcLwOHG74kS040WOcQq
uATgcnobOf/D8ZmlqvfKGAeTUoFo/RSR2Uhlauka58qgeUbicrTELZT2barY9d+k
as6U5vv4wx2zMklTkjrlkMpAT1ZpbB9d3jGHwL27VEnjlfd3wV2bdH7Dzn9qZRf/
gn0ALg/b3u5yBWk/k7YBvijXyNcH6Q==
=bBuG
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-07-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.6:
UAPI Changes:
* fbdev:
* Make fbdev userspace interfaces optional; only leaves the
framebuffer console active
* prime:
* Support dma-buf self-import for all drivers automatically: improves
support for many userspace compositors
Cross-subsystem Changes:
* backlight:
* Fix interaction with fbdev in several drivers
* base: Convert struct platform.remove to return void; part of a larger,
tree-wide effort
* dma-buf: Acquire reservation lock for mmap() in exporters; part
of an on-going effort to simplify locking around dma-bufs
* fbdev:
* Use Linux device instead of fbdev device in many places
* Use deferred-I/O helper macros in various drivers
* i2c: Convert struct i2c from .probe_new to .probe; part of a larger,
tree-wide effort
* video:
* Avoid including <linux/screen_info.h>
Core Changes:
* atomic:
* Improve logging
* prime:
* Remove struct drm_driver.gem_prime_mmap plus driver updates: all
drivers now implement this callback with drm_gem_prime_mmap()
* gem:
* Support execution contexts: provides locking over multiple GEM
objects
* ttm:
* Support init_on_free
* Swapout fixes
Driver Changes:
* accel:
* ivpu: MMU updates; Support debugfs
* ast:
* Improve device-model detection
* Cleanups
* bridge:
* dw-hdmi: Improve support for YUV420 bus format
* dw-mipi-dsi: Fix enable/disable of DSI controller
* lt9611uxc: Use MODULE_FIRMWARE()
* ps8640: Remove broken EDID code
* samsung-dsim: Fix command transfer
* tc358764: Handle HS/VS polarity; Use BIT() macro; Various cleanups
* Cleanups
* ingenic:
* Kconfig REGMAP fixes
* loongson:
* Support display controller
* mgag200:
* Minor fixes
* mxsfb:
* Support disabling overlay planes
* nouveau:
* Improve VRAM detection
* Various fixes and cleanups
* panel:
* panel-edp: Support AUO B116XAB01.4
* Support Visionox R66451 plus DT bindings
* Cleanups
* ssd130x:
* Support per-controller default resolution plus DT bindings
* Reduce memory-allocation overhead
* Cleanups
* tidss:
* Support TI AM625 plus DT bindings
* Implement new connector model plus driver updates
* vkms
* Improve write-back support
* Documentation fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713090830.GA23281@linux-uq9g
The intent of this test is to check we get a PERF_RECORD_EXIT as asked
for by setting perf_event_attr.task=1.
When the test was written we didn't had the "dummy" event so we went
with the default event, "cycles".
There were reports of this test failing sometimes, one of these reports
was with a PREEMPT_RT_FULL, but I noticed it failing sometimes with an
aarch64 Firefly board.
In the kernel the call to perf_event_task_output(), that generates the
PERF_RECORD_EXIT may fail when there is not enough memory in the ring
buffer, if the ring buffer is paused, etc.
So switch to using the "dummy" event to use the ring buffer just for
what the test was designed for, avoiding uneeded PERF_RECORD_SAMPLEs.
Acked-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/ZLGXmMuNRpx1ubFm@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The `nocrt` module parameter has no code associated with it and does
nothing. As `crt=-1` has same functionality as what nocrt should be
doing drop `nocrt` and associated documentation.
This should fix a quirk for Gigabyte GA-7ZX that used `nocrt` and
thus didn't function properly.
Fixes: 8c99fdce30 ("ACPI: thermal: set "thermal.nocrt" via DMI on Gigabyte GA-7ZX")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix the following smatch error:
drivers/interconnect/qcom/icc-rpm.c:243 qcom_icc_rpm_set() error: uninitialized symbol 'ret'.
Fixes: 32846c4a8f ("interconnect: qcom: icc-rpm: Set bandwidth on both contexts")
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230717125534.2455745-1-djakov@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The Lenovo Ideapad Z470 predates Windows 8, so it defaults to using
acpi_video for backlight control. But this is not functional on this
model.
Add a DMI quirk to use the native backlight interface which works.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1208724
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As per the generic KASAN code in mm/kasan, disable KCOV with
KCOV_INSTRUMENT := n in the makefile.
This fixes a ppc64 boot hang when KCOV and KASAN are enabled.
kasan_early_init() gets called before a PACA is initialised, but the
KCOV hook expects a valid PACA.
Suggested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230710044143.146840-1-bgray@linux.ibm.com
The workaround for buggy skylake BIOSes is now implemented in
acpi_processor_osc() and acpi_hwp_native_thermal_lvt_osc() has no
callers, so drop it.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change acpi_early_processor_osc() to return a value in case of a
failure and make it static.
Also make it run acpi_processor_osc() for every processor object or
processor device found in the ACPI Namespace (previously, its only purpose
was to work around platform firmware defects on Skylake systems).
Introduce a new function called acpi_early_processor_control_setup() that
will invoke acpi_early_processor_osc() first in order to convey the OS
processor support information to the platform firmware and if that fails,
it will fall back to using _PDC.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ rjw: Subject and changelog edits, change function return value to bool,
add missing 'static', change messages ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 88e9664434.
__diag_ignore_all() only works for GCC 8 or later.
-Woverride-init (from -Wextra, enabled in i915 Makefile) combined with
CONFIG_WERROR=y or W=e breaks the build for older GCC.
With i386_defconfig and x86_64_defconfig enabling CONFIG_WERROR=y by
default, we really need to roll back the change.
An alternative would be to disable -Woverride-init in the Makefile for
GCC <8, but the revert seems like the safest bet now.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8768
Reported-by: John Garry <john.g.garry@oracle.com>
References: https://lore.kernel.org/r/ad2601c0-84bb-c574-3702-a83ff8faf98c@oracle.com
References: https://lore.kernel.org/r/87wmzezns4.fsf@intel.com
Fixes: 88e9664434 ("drm/i915: use localized __diag_ignore_all() instead of per file")
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Tested-by: John Garry <john.g.garry@oracle.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230711110214.25093-1-jani.nikula@intel.com
(cherry picked from commit 290d161045)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Henry reported that rt_mutex_adjust_prio_check() has an ordering
problem and puts the lie to the comment in [7]. Sharing the sort key
between lock->waiters and owner->pi_waiters *does* create problems,
since unlike what the comment claims, holding [L] is insufficient.
Notably, consider:
A
/ \
M1 M2
| |
B C
That is, task A owns both M1 and M2, B and C block on them. In this
case a concurrent chain walk (B & C) will modify their resp. sort keys
in [7] while holding M1->wait_lock and M2->wait_lock. So holding [L]
is meaningless, they're different Ls.
This then gives rise to a race condition between [7] and [11], where
the requeue of pi_waiters will observe an inconsistent tree order.
B C
(holds M1->wait_lock, (holds M2->wait_lock,
holds B->pi_lock) holds A->pi_lock)
[7]
waiter_update_prio();
...
[8]
raw_spin_unlock(B->pi_lock);
...
[10]
raw_spin_lock(A->pi_lock);
[11]
rt_mutex_enqueue_pi();
// observes inconsistent A->pi_waiters
// tree order
Fixing this means either extending the range of the owner lock from
[10-13] to [6-13], with the immediate problem that this means [6-8]
hold both blocked and owner locks, or duplicating the sort key.
Since the locking in chain walk is horrible enough without having to
consider pi_lock nesting rules, duplicate the sort key instead.
By giving each tree their own sort key, the above race becomes
harmless, if C sees B at the old location, then B will correct things
(if they need correcting) when it walks up the chain and reaches A.
Fixes: fb00aca474 ("rtmutex: Turn the plist into an rb-tree")
Reported-by: Henry Wu <triangletrap12@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Henry Wu <triangletrap12@gmail.com>
Link: https://lkml.kernel.org/r/20230707161052.GF2883469%40hirez.programming.kicks-ass.net
The ternary operators used to initialize tx_completed and rx_completed
are not necessary, replace them with a better implementation.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230715010407.1751715-6-fabrizio.castro.jz@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both rzv2m_csi_sw_reset and rzv2m_csi_start_stop_operation
call into readl_poll_timeout upon a certain condition, and
return 0 otherwise.
Flip the logic to improve readability.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230715010407.1751715-5-fabrizio.castro.jz@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clock "csiclk" gets divided by 2 * CSI_CLKSEL_CKS in order to generate
the serial clock (output from master), with CSI_CLKSEL_CKS ranging from
0x1 (that means "csiclk" is divided by 2) to 0x3FFF ("csiclk" is divided
by 32766). CSI_CKS_MAX is used for referring to the setting
corresponding to the maximum frequency divider.
Value 0x3FFF for CSI_CKS_MAX doesn't really means much to the reader
without an explanation and a more readable definition.
Add a comment with a meaningful description and also replace value
0x3FFF with the corresponding GENMASK, to make it very clear what the
macro means.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230715010407.1751715-4-fabrizio.castro.jz@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of HZ_PER_MHZ for CSI_MAX_SPI_SCKO to make it clear
what its value means.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230715010407.1751715-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the gs_usb device driver is unloaded (or unbound) before the
interface is shut down, the USB stack first calls the struct
usb_driver::disconnect and then the struct net_device_ops::ndo_stop
callback.
In gs_usb_disconnect() all pending bulk URBs are killed, i.e. no more
RX'ed CAN frames are send from the USB device to the host. Later in
gs_can_close() a reset control message is send to each CAN channel to
remove the controller from the CAN bus. In this race window the USB
device can still receive CAN frames from the bus and internally queue
them to be send to the host.
At least in the current version of the candlelight firmware, the queue
of received CAN frames is not emptied during the reset command. After
loading (or binding) the gs_usb driver, new URBs are submitted during
the struct net_device_ops::ndo_open callback and the candlelight
firmware starts sending its already queued CAN frames to the host.
However, this scenario was not considered when implementing the
hardware timestamp function. The cycle counter/time counter
infrastructure is set up (gs_usb_timestamp_init()) after the USBs are
submitted, resulting in a NULL pointer dereference if
timecounter_cyc2time() (via the call chain:
gs_usb_receive_bulk_callback() -> gs_usb_set_timestamp() ->
gs_usb_skb_set_timestamp()) is called too early.
Move the gs_usb_timestamp_init() function before the URBs are
submitted to fix this problem.
For a comprehensive solution, we need to consider gs_usb devices with
more than 1 channel. The cycle counter/time counter infrastructure is
setup per channel, but the RX URBs are per device. Once gs_can_open()
of _a_ channel has been called, and URBs have been submitted, the
gs_usb_receive_bulk_callback() can be called for _all_ available
channels, even for channels that are not running, yet. As cycle
counter/time counter has not set up, this will again lead to a NULL
pointer dereference.
Convert the cycle counter/time counter from a "per channel" to a "per
device" functionality. Also set it up, before submitting any URBs to
the device.
Further in gs_usb_receive_bulk_callback(), don't process any URBs for
not started CAN channels, only resubmit the URB.
Fixes: 45dfa45f52 ("can: gs_usb: add RX and TX hardware timestamp support")
Closes: https://github.com/candle-usb/candleLight_fw/issues/137#issuecomment-1623532076
Cc: stable@vger.kernel.org
Cc: John Whittington <git@jbrengineering.co.uk>
Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-2-9017cefcd9d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gs_usb driver handles USB devices with more than 1 CAN channel.
The RX path for all channels share the same bulk endpoint (the
transmitted bulk data encodes the channel number). These per-device
resources are allocated and submitted by the first opened channel.
During this allocation, the resources are either released immediately
in case of a failure or the URBs are anchored. All anchored URBs are
finally killed with gs_usb_disconnect().
Currently, gs_can_open() returns with an error if the allocation of a
URB or a buffer fails. However, if usb_submit_urb() fails, the driver
continues with the URBs submitted so far, even if no URBs were
successfully submitted.
Treat every error as fatal and free all allocated resources
immediately.
Switch to goto-style error handling, to prepare the driver for more
per-device resource allocation.
Cc: stable@vger.kernel.org
Cc: John Whittington <git@jbrengineering.co.uk>
Link: https://lore.kernel.org/all/20230716-gs_usb-fix-time-stamp-counter-v1-1-9017cefcd9d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use smem on MTL due to a HW bug in MTL that prevents
reading from stolen memory using LMEM BAR.
v2 and v3: improve stolen skip detection(Andrzej)
Cc: Oak Zeng <oak.zeng@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Oak Zeng <oak.zeng@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713150142.12700-2-nirmoy.das@intel.com
The GPU is halted when it hits a MMU exception, so there is no point in
waiting for the job timeout to expire or try to work out if the GPU is
still making progress in the timeout handler, as we know that the GPU
won't make any more progress.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Now that it is only used to track the driver internal state of
the MMU global and cmdbuf objects, we can get rid of this property
by making the free/finit functions of those objects safe to call
on an uninitialized object.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Instead of only tracking if the FE is running, use a enum to better
describe the various states the GPU can be in. This allows some
additional validation to make sure that functions that expect a
certain GPU state are only called when the GPU is actually in that
state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Nothing in this callpath actually touches the GPU, so there is no reason
to get it out of suspend state here. Only if runtime PM isn't enabled at
all we must make sure to enable the clocks, so the GPU init routine can
access the GPU later on.
This also removes the need to guard against the state where the driver
isn't fully initialized yet in the runtime PM resume handler.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Currently the clock is enabled in the runtime resume function, but are
disabled a level further down in the callstack in the suspend function.
Move the clock disable into the suspend function to make handling
symmetrical between resume and suspend.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Conceptually events are the right abstraction to handle the GPU
runtime PM state: as long as any event is pending the GPU can not
be idle. Events are also properly freed and reallocated when the
GPU has been reset after a hang.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
Clearing the whole bitmap at once is only a minor optimization in
a path that should be extremely cold. Free the events by calling
event_free() instead of directly manipulating the completion count
and event bitmap.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
So it can use the event_free function without adding another
forward declaration. No functional change.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com>
This is the 2D GPU found on the i.MX8MP SoC. Feature bits taken
from the downstream kernel driver 6.4.3.p4.4.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
This is the NPU found on the NXP i.MX8MP SoC. Feature bits taken
from the downstream kernel driver 6.4.3.p4.4.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
gpu->mmu_context is the MMU context of the last job in the HW queue, which
isn't necessarily the same as the context from the bad job. Dump the MMU
context from the scheduler determined bad submit to make it work as intended.
Fixes: 17e4660ae3 ("drm/etnaviv: implement per-process address spaces on MMUv2")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Use smem on MTL due to a HW bug in MTL that prevents
reading from stolen memory using LMEM BAR.
Cc: Oak Zeng <oak.zeng@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Oak Zeng <oak.zeng@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230713150142.12700-1-nirmoy.das@intel.com
Luo Jie says:
====================
net: phy: at803x: support qca8081 1G version chip
This patch series add supporting qca8081 1G version chip, the 1G version
chip can be identified by the register mmd7.0x901d bit0.
In addition, qca8081 does not support 1000BaseX mode and the sgmii fifo
reset is added on the link changed, which assert the fifo on the link
down, deassert the fifo on the link up.
Changes in v1:
* switch to use genphy_c45_pma_read_abilities.
* remove the patch [remove 1000BaseX mode of qca8081].
* move the sgmii fifo reset to link_change_notify.
Changes in v2:
* split the qca8081 1G chip support patch.
* improve the slave seed config, disable it if master preferred.
Changes in v3:
* fix the comments.
* add the help function qca808x_has_fast_retrain_or_slave_seed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8081 sgmii fifo needs to be reset on link down and
released on the link up in case of any abnormal issue
such as the packet blocked on the PHY.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fast retrain and slave seed configs are only applicable when the 2.5G
ability is supported.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8081 1G chip version does not support 2.5 capability, which
is distinguished from qca8081 2.5G chip according to the bit0 of
register mmd7.0x901d, the 1G version chip also has the same PHY ID
as the normal qca8081 2.5G chip.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 is the single port PHY, the slave prefer mode is used
by default.
if the phy master perfer mode is configured, the slave seed
configuration should not be enabled, since the slave seed
enablement is for making PHY linked as slave mode easily.
disable slave seed if the master mode is preferred.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
merge the seed enablement and seed value configuration into
one function, since the random seed value is needed to be
configured when the seed is enabled.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 PHY supports to use genphy_c45_pma_read_abilities for
getting the PHY features supported except for the autoneg ability
but autoneg ability exists in MDIO_STAT1 instead of MMD7.1, add it
manually after calling genphy_c45_pma_read_abilities.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it clearer that the values cannot be changed because
they are ABI.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by:James Zhu <James.Zhu@amd.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Marek Olšák <marek.olsak@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714104557.518457-2-contact@emersion.fr
This makes it easier to figure out what the "type" variable can be
set to when reading the implementation of these functions.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by:James Zhu <James.Zhu@amd.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Christian König <christian.koenig@amd.com>
Cc: Marek Olšák <marek.olsak@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714104557.518457-1-contact@emersion.fr
Vignesh Viswanathan says:
====================
net: qrtr: Few fixes in QRTR
Add fixes in QRTR ns to change server and nodes radix tree to xarray to
avoid a use-after-free while iterating through the server or nodes
radix tree.
Also fix the destination port value for IPCR control buffer on older
targets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The destination port value in the IPCR control buffer on older
targets is 0xFFFF. Handle the same by updating the dst_port to
QRTR_PORT_CTRL.
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a use after free scenario while iterating through the nodes
radix tree despite the ns being a single threaded process. This can
happen when the radix tree APIs are not synchronized with the
rcu_read_lock() APIs.
Convert the radix tree for nodes to xarray to take advantage of the
built in rcu lock usage provided by xarray.
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a use after free scenario while iterating through the servers
radix tree despite the ns being a single threaded process. This can
happen when the radix tree APIs are not synchronized with the
rcu_read_lock() APIs.
Convert the radix tree for servers to xarray to take advantage of the
built in rcu lock usage provided by xarray.
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove the "log-like" parts, following the same logic as the previous
commit
- Unify format
- Add missing major contributors, including myself
- Sort entries in order of first contribution (Creative comes last for
optical reasons; they don't appear to have directly contributed
anyway)
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160839.326978-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>