The call netdev_{put, hold} of dev_{put, hold} will check NULL,
so there is no need to check before using dev_{put, hold},
remove it to silence the warnings:
./drivers/leds/trigger/ledtrig-netdev.c:291:3-10: WARNING: NULL check before dev_{put, hold} functions is not needed.
./drivers/leds/trigger/ledtrig-netdev.c:401:2-9: WARNING: NULL check before dev_{put, hold} functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=4929
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230511070820.52731-1-yang.lee@linux.alibaba.com
Signed-off-by: Lee Jones <lee@kernel.org>
Not all triggers use LED_INIT_DEFAULT_TRIGGER, which means that it
will not get cleared when the default trigger is a trigger which
does not use it such as "default-on".
If the default trigger then later gets replaced by a trigger which
does check LED_INIT_DEFAULT_TRIGGER, such as "timer" then that trigger
will behave as if it is the default trigger which it should not do.
To fix this clear the LED_INIT_DEFAULT_TRIGGER flag when clearing
the current trigger, so that it will not be set for any subsequently
set (non default) triggers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-5-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
led_trigger_blink() calls led_blink_set() from a RCU read-side critical
section so led_blink_set() must not sleep. Note sleeping was not allowed
before the switch to RCU either because a spinlock was held before.
led_blink_set() does not sleep when sw-blinking is used, but
many LED controller drivers with hw blink support have a blink_set
function which may sleep, leading to an oops like this one:
[ 832.605062] ------------[ cut here ]------------
[ 832.605085] Voluntary context switch within RCU read-side critical section!
[ 832.605119] WARNING: CPU: 2 PID: 370 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x4ee/0x690
<snip>
[ 832.606453] Call Trace:
[ 832.606466] <TASK>
[ 832.606487] __schedule+0x9f/0x1480
[ 832.606527] schedule+0x5d/0xe0
[ 832.606549] schedule_timeout+0x79/0x140
[ 832.606572] ? __pfx_process_timeout+0x10/0x10
[ 832.606599] wait_for_completion_timeout+0x6f/0x140
[ 832.606627] i2c_dw_xfer+0x101/0x460
[ 832.606659] ? psi_group_change+0x168/0x400
[ 832.606680] __i2c_transfer+0x172/0x6d0
[ 832.606709] i2c_smbus_xfer_emulated+0x27d/0x9c0
[ 832.606732] ? __schedule+0x430/0x1480
[ 832.606753] ? preempt_count_add+0x6a/0xa0
[ 832.606778] ? get_nohz_timer_target+0x18/0x190
[ 832.606796] ? lock_timer_base+0x61/0x80
[ 832.606817] ? preempt_count_add+0x6a/0xa0
[ 832.606842] __i2c_smbus_xfer+0xa2/0x3f0
[ 832.606862] i2c_smbus_xfer+0x66/0xf0
[ 832.606882] i2c_smbus_read_byte_data+0x41/0x70
[ 832.606901] ? _raw_spin_unlock_irqrestore+0x23/0x40
[ 832.606922] ? __pm_runtime_suspend+0x46/0xc0
[ 832.606946] cht_wc_byte_reg_read+0x2e/0x60
[ 832.606972] _regmap_read+0x5c/0x120
[ 832.606997] _regmap_update_bits+0x96/0xc0
[ 832.607023] regmap_update_bits_base+0x5b/0x90
[ 832.607053] cht_wc_leds_brightness_get+0x412/0x910 [leds_cht_wcove]
[ 832.607094] led_blink_setup+0x28/0x100
[ 832.607119] led_trigger_blink+0x40/0x70
[ 832.607145] power_supply_update_leds+0x1b7/0x1c0
[ 832.607174] power_supply_changed_work+0x67/0xe0
[ 832.607198] process_one_work+0x1c8/0x3c0
[ 832.607222] worker_thread+0x4d/0x380
[ 832.607243] ? __pfx_worker_thread+0x10/0x10
[ 832.607258] kthread+0xe9/0x110
[ 832.607279] ? __pfx_kthread+0x10/0x10
[ 832.607300] ret_from_fork+0x2c/0x50
[ 832.607337] </TASK>
[ 832.607344] ---[ end trace 0000000000000000 ]---
Add a new led_blink_set_nosleep() function which defers the actual
led_blink_set() call to a workqueue when necessary to fix this.
This also fixes an existing race where a pending led_set_brightness() has
been deferred to set_brightness_work and might then race with a later
led_cdev->blink_set() call. Note this race is only an issue with triggers
mixing led_trigger_event() and led_trigger_blink() calls, sysfs API
calls and led_trigger_blink_oneshot() are not affected.
Note rather then adding a separate blink_set_blocking callback this uses
the presence of the already existing brightness_set_blocking callback to
detect if the blinking call should be deferred to set_brightness_work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-4-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
When a trigger wants to switch from blinking to LED on it needs to call:
led_set_brightness(LED_OFF);
led_set_brightness(LED_FULL);
To first call disables blinking and the second then turns the LED on
(the power-supply charging-blink-full-solid triggers do this).
These calls happen immediately after each other, so it is possible
that set_brightness_delayed() from the first call has not run yet
when the led_set_brightness(LED_FULL) call finishes.
If this race hits then this is causing problems for both
sw- and hw-blinking:
For sw-blinking set_brightness_delayed() clears delayed_set_value
when LED_BLINK_DISABLE is set causing the led_set_brightness(LED_FULL)
call effects to get lost when hitting the race, resulting in the LED
turning off instead of on.
For hw-blinking if the race hits delayed_set_value has been
set to LED_FULL by the time set_brightness_delayed() runs.
So led_cdev->brightness_set_blocking() is never called with
LED_OFF as argument and the hw-blinking is never disabled leaving
the LED blinking instead of on.
Fix both issues by adding LED_SET_BRIGHTNESS and LED_SET_BRIGHTNESS_OFF
work_flags making this 2 separate actions to be run by
set_brightness_delayed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-3-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
led_blink_set[_oneshot]()'s delay_on and delay_off function parameters
are pass by reference, so that hw-blink implementations can report
back the actual achieved delays when the values have been rounded
to something the hw supports.
This is really only interesting for the sysfs API / the timer trigger.
Other triggers don't really care about this and none of the callers of
led_trigger_blink[_oneshot]() do anything with the returned delay values.
Change the led_trigger_blink[_oneshot]() delay parameters to pass-by-value,
there are 2 reasons for this:
1. led_cdev->blink_set() may sleep, while led_trigger_blink() may not.
So on hw where led_cdev->blink_set() sleeps the call needs to be deferred
to a workqueue, in which case the actual achieved delays are unknown
(this is a preparation patch for the deferring).
2. Since the callers don't care about the actual achieved delays, allowing
callers to directly pass a value leads to simpler code for most callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517180559.166329-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
Currently, LEDS_LM3697 and LEDS_LM36274 depend on LEDS_TI_LMU_COMMON,
which contains the common code to support TI LMU devices. This means
the user is asked about the common code first, followed by the
individual drivers, if their dependencies are met.
Simplify this, and reduce the number of questions by making
LEDS_TI_LMU_COMMON invisible, and letting it be selected when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/91f6efaa48c36320e58b6a312025ae9b39ee206b.1683644796.git.geert+renesas@glider.be
Signed-off-by: Lee Jones <lee@kernel.org>
The Qualcomm PMI8998 PMIC requires the LED to be disabled when configuring
the brightness. Always disable the LED when setting the brightness and
re-enable it afterwards.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Link: https://lore.kernel.org/r/20230507172941.364852-3-me@dylanvanassche.be
Signed-off-by: Lee Jones <lee@kernel.org>
Add subtype for the Qualcomm PMI8998 PMIC to support it besides the
PM8150 PMIC which has the same registers. Adjust the driver to recognize
both PMIC subtypes as a 3 channel LED driver.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Link: https://lore.kernel.org/r/20230507172941.364852-2-me@dylanvanassche.be
Signed-off-by: Lee Jones <lee@kernel.org>
The desired default behavior of LED1 / the charge LED is breathing
while charging and on/solid when full. Since triggers cannot select
breathing, blink_set() gets called when charging. Use breathing
when the default "charging-blink-full-solid" trigger is used to
achieve the desired default behavior.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-6-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
The hw-blinking of the LED controller in the Whiskey Cove PMIC can also
be used for a hw-breathing effect.
As discussed during review of v2 of the submission of the new
leds-cht-wcove driver, the LED subsystem already supports breathing mode
on several other LED controllers using the hw_pattern interface.
Implement a pattern_set callback to implement breathing mode modelled
after the breathing mode supported by the SC27xx breathing light and
Crane EL15203000 LED drivers. The Whiskey Cove PMIC's breathing mode
is closer to the EL15203000 one then to the SC27xx one since it does
not support staying high / low for a specific time, it only supports
rise and fall times.
As such the supported hw_pattern and the documentation for this is almost
a 1:1 copy of the pattern/docs for the EL15203000 breathing mode.
Suggested-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Link: https://lore.kernel.org/all/6beed61c-1fc6-6525-e873-a8978f5fbffb@gmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-4-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
When LED1 is showing the tablet is charging and then the device gets
suspended followed by unplugging the charger, then it will incorrectly
still show it is charging.
To avoid this turn both LEDs off on suspend, just like the PMIC always
turns them off when the tablet is powered off (even if the tablet is
charging). If hw-control is supported for LED1, then restore the
initial hw-control settings to let the hw control LED1 while suspended.
To restore the state the LEDs had before suspending, save it before
turning the LEDs off and restore it on resume.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-3-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
is implemented, breathing is not.
This driver was tested with Lenovo Yoga Book notebook.
Changes by Hans de Goede (in response to review of v2):
- Since the PMIC is connected to the battery any changes we make to
the LED settings are permanent, even surviving reboot / poweroff.
Save LED1 register settings on probe() and if auto-/hw-control was
enabled on probe() restore the settings on remove() and shutdown().
- Delay switching LED1 to software control mode to first brightness write.
- Use dynamically allocated drvdata instead of a global drvdata variable.
- Ensure the LED is on when activating blinking.
- Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).
Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Commit e91a4d5deb ("dt-bindings: leds: Document commonly used
LED triggers") introduced a enum match for cpu, while a pattern
'^cpu[0-9]*$' already exists.
This causes linux,default-trigger = "cpu" to have more than one match
and generates the following dtbs_check warning:
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dtb: leds: led-2:linux,default-trigger: More than one condition true in oneOf schema:
{'$ref': '/schemas/types.yaml#/definitions/string',
'oneOf': [{'items': [{'enum': ['backlight',
'default-on',
'heartbeat',
'disk-activity',
'disk-read',
'disk-write',
'timer',
'pattern',
'audio-micmute',
'audio-mute',
'bluetooth-power',
'cpu',
'flash',
'kbd-capslock',
'mtd',
'nand-disk',
'none',
'torch',
'usb-gadget',
'usb-host',
'usbport']}],
'maxItems': 1,
'minItems': 1,
'type': 'array'},
{'items': [{'pattern': '^cpu[0-9]*$'}],
'maxItems': 1,
'minItems': 1,
'type': 'array'},
{'items': [{'pattern': '^hci[0-9]+-power$'}],
'maxItems': 1,
'minItems': 1,
'type': 'array'},
{'items': [{'pattern': '^mmc[0-9]+$'}],
'maxItems': 1,
'minItems': 1,
'type': 'array'},
{'items': [{'pattern': '^phy[0-9]+tx$'}],
'maxItems': 1,
'minItems': 1,
'type': 'array'}]}
Drop the explicit match against cpu since the pattern match already
covers the same.
Fixes: e91a4d5deb ("dt-bindings: leds: Document commonly used LED triggers")
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230424151437.256073-1-nm@ti.com
Document support for the pmi632, often found with the sdm632 SoC.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-5-98bafa909c36@z3ntu.xyz
The PMI632 PMIC contains 5 PWM channels, 3 of which can be used for
LEDs.
For the LED pattern it doesn't have LUT like other PMICs but uses SDAM
instead. This is not currently implemented in the driver but since LPG
works fine without it, add support for the PMIC now.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-4-98bafa909c36@z3ntu.xyz
Document the availability of an LPG configuration for the PMI632 PMIC in
the Qualcomm Light Pulse Generator driver.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-3-98bafa909c36@z3ntu.xyz
The LP55xx range of devices have an internal charge pump which
can (automatically) increase the output voltage towards the
LED's, boosting the output voltage to 4.5V.
Implement this option from the devicetree. When the setting
is not present it will operate in automatic mode as before.
Tested on LP55231. Datasheet analysis shows that LP5521, LP5523
and LP8501 are identical in topology and are modified in the
same way.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230421075305.37597-3-maarten.zanders@mind.be
Add a binding to configure the internal charge pump for lp55xx.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230421075305.37597-2-maarten.zanders@mind.be
If CONFIG_DEBUG_FS is not set:
regulator: Failed to create debugfs directory
...
regulator-dummy: Failed to create debugfs directory
As per the comments for debugfs_create_dir(), errors returned by this
function should be expected, and ignored:
* If debugfs is not enabled in the kernel, the value -%ENODEV will be
* returned.
*
* NOTE: it's expected that most callers should _ignore_ the errors returned
* by this function. Other debugfs functions handle the fact that the "dentry"
* passed to them could be an error and they don't crash in that case.
* Drivers should generally work fine even if debugfs fails to init anyway.
Adhere to the debugfs spirit, and streamline all operations by:
1. Demoting the importance of the printed error messages to debug
level, like is already done in create_regulator(),
2. Further ignoring any returned errors, as by design, all debugfs
functions are no-ops when passed an error pointer.
Fixes: 2bf1c45be3 ("regulator: Fix error checking for debugfs_create_dir")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2f8bb6e113359ddfab7b59e4d4274bd4c06d6d0a.1685013051.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of failure, debugfs_create_dir() does not return NULL, but an
error pointer. Most incorrect error checks were fixed, but the one in
create_regulator() was forgotten.
Fix the remaining error check.
Fixes: 2bf1c45be3 ("regulator: Fix error checking for debugfs_create_dir")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/ee980a108b5854dd8ce3630f8f673e784e057d17.1685013051.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Some LEDs may require to sleep while doing some operation like setting
brightness and other cleanup.
For this reason, using a spinlock will cause a sleep under spinlock
warning.
It should be safe to convert this to a sleepable lock since:
- sysfs read/write can sleep
- netdev_trig_work is a work queue and can sleep
- netdev _trig_notify can sleep
The spinlock was used when brightness didn't support sleeping, but this
changed and now it supported with brightness_set_blocking().
Convert to mutex lock to permit sleeping using brightness_set_blocking().
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-6-ansuelsmth@gmail.com
Convert link tx and rx device attr to a common macro to reduce common
code and in preparation for additional attr.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-5-ansuelsmth@gmail.com
Rename NETDEV trigger enum modes to a more symbolic name and add a
namespace to them.
Also add __TRIGGER_NETDEV_MAX to identify the max modes of the netdev
trigger.
This is a cleanup to drop the define and no behaviour change are
intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-4-ansuelsmth@gmail.com
Putting NETDEV_LED_MODE_LINKUP in the same list of the netdev trigger
modes is wrong as it's used to set the link state of the device and not
to set a blink mode as it's done by NETDEV_LED_LINK, NETDEV_LED_TX and
NETDEV_LED_RX. It's also wrong to put this state in the same bitmap of the
netdev trigger mode and should be external to it.
Drop NETDEV_LED_MODE_LINKUP from mode list and convert to a simple bool
that will be true or false based on the carrier link. No functional
change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-3-ansuelsmth@gmail.com
Dev can be renamed also while up for supported device. We currently
wrongly clear the NETDEV_LED_MODE_LINKUP flag on NETDEV_CHANGENAME
event.
Fix this by rechecking if the carrier is ok on NETDEV_CHANGENAME and
correctly set the NETDEV_LED_MODE_LINKUP bit.
Fixes: 5f820ed523 ("leds: trigger: netdev: fix handling on interface rename")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-2-ansuelsmth@gmail.com
Tegra20 can do horizontal and vertical image flip, but Tegra210 cannot
(either the hardware, or this driver).
In preparation to adding Tegra20 support, add a flag in struct tegra_vi_soc
so the generic vi.c code knows whether the flip controls should be added or
not.
Also provide a generic implementation that simply sets two flags in the
channel struct. The Tegra20 implementation will enable flipping at stream
start based on those flags.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tegra20 supports planar YUV422 capture, which can be implemented by writing
U and V base address registers in addition to the "main" base buffer
address register.
It also supports H and V flip, which among others requires to write the
start address (i.e. the 1st offset to write, at the end of the buffer or
line) in more registers for Y and, for planar formats, U and V.
Add minimal hooks in VI to allow per-SoC optional support to those
features:
- variables in struct tegra_vi for the U and V buffer base offsets
- variables in struct tegra_vi for the Y, U and V buffer start offsets
- an optional per-soc VI operation to compute those values on queue setup
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In preparation to implement Tegra20 parallel video capture, add a variable
to hold the required syncpt and document all the syncpt variables.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
tegra_channel_host1x_syncpt_init() gets the host1x syncpts needed for the
Tegra210 implementation, and tegra_channel_host1x_syncpts_free() puts
them.
Tegra20 needs to get and put a different syncpt. In preparation for adding
Tegra20 support, move these functions to new ops in the soc-specific
`struct tegra_vi_ops` .
No functional changes.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Tegra20 VI needs an additional operation to enable the VI, add an
operation for that.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The CSI module does not handle all the MIPI lane calibration procedure,
leaving a small part of it to the VI module. In doing this,
tegra_channel_enable_stream() (vi.c) manipulates the private data of the
upstream subdev casting it to struct 'tegra_csi_channel', which will be
wrong after introducing a VIP (parallel video input) channel.
This prevents adding support for the VIP module. It also breaks the
logical isolation between modules.
Since the lane calibration requirement does not exist in the parallel input
module, moving the calibration function to a per-module op is not
optimal. Instead move the calibration procedure in the CSI module, together
with the rest of the calibration procedures. After this change,
tegra_channel_enable_stream() just calls v4l2_subdev_call() to ask for a
stream start/stop to the CSI module, which in turn knows all the
CSI-specific details to implement it.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The tegra_default_format in vi.c is specific to Tegra210 CSI.
In preparation for adding Tegra20 VIP support, move the default format to a
new field in the soc-specific `struct tegra_vi_soc`. Instead of an entire
format struct, only store a pointer to an item in the existing format
array.
No functional changes. The format pointed to is the same that used to be in
vi.c.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
tegra_channel_fmt_align() takes care of the size constraints, alignment and
rounding requirements of the Tegra210 VI peripheral. Tegra20 has different
constraints.
In preparation for adding Tegra20 support, move this function to a new op
in the soc-specific `struct tegra_vi_ops` .
Also move to tegra210.c the T210-specific defines used in the moved code.
No functional changes.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
We are about to add support for the Tegra20 parallel video capture, which
has no TPG. In preparation for that, limit the VIDEO_TEGRA_TPG option to
Tegra210 which is the only implementation currently provided by this
driver.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is only a pointer reference to struct tegra_vi in video.h, thus vi.h
is not needed.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This declaration is used only in csi.c, no need to export it elsewhere.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
struct tegra_vi_graph_entity is an internal implementation detail of the VI
module. Move its declaration from vi.h to vi.c.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
of_node_put(node) does nothing if node == NULL, so it can be moved to the
cleanup section at the bottom.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
tegra_vi_channels_alloc() can primarily fail for two reasons:
1. "ports" node not found
2. port_num > vi->soc->vi_max_channels
Case 1 prints nothing, case 2 has a dev_err(). The caller [tegra_vi_init()]
has a generic dev_err() on any failure. This mean that in case 2 we print
two messages, and in case 1 we only print a generic message.
Remove the generic message and add a specific message when case 1 happens,
so that we always have one specific message without even increasing the
number of dev_dbg*() calls.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add "skip" in "so we can *skip* the current channel" or it doesn't make
sense.
Also add articles where appropriate to fix English grammar.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Clarify what this function does.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some fields are irrelevant for Tegra20/VIP. Add a note to clarify that.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Tegra20 VI peripheral can receive parallel input from the VIP parallel
input module. Add it to the allowed properties and augment the existing
nvidia,tegra20-vi example to show a 'vip' property.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VIP is the parallel video capture component within the video input
subsystem of Tegra20 (and other Tegra chips, apparently).
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
this patch advertise the availability of Dual and Quad SPI mode
for ipm design.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Tim.Kuo <Tim.kuo@mediatek.com>
Link: https://lore.kernel.org/r/20230523112608.10298-1-qii.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 4.8Mhz 9.6Mhz and 19.2MHz SCLK values
for MCLK 12MHz and 12.288MHz requested by Intel.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230524125236.57149-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>