The cper.c file needs to include an extra header, and efi_zboot_entry
needs an extern declaration to avoid these 'make W=1' warnings:
drivers/firmware/efi/libstub/zboot.c:65:1: error: no previous prototype for 'efi_zboot_entry' [-Werror=missing-prototypes]
drivers/firmware/efi/efi.c:176:16: error: no previous prototype for 'efi_attr_is_visible' [-Werror=missing-prototypes]
drivers/firmware/efi/cper.c:626:6: error: no previous prototype for 'cper_estatus_print' [-Werror=missing-prototypes]
drivers/firmware/efi/cper.c:649:5: error: no previous prototype for 'cper_estatus_check_header' [-Werror=missing-prototypes]
drivers/firmware/efi/cper.c:662:5: error: no previous prototype for 'cper_estatus_check' [-Werror=missing-prototypes]
To make this easier, move the cper specific declarations to
include/linux/cper.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The Make variable containing the objcopy flags may be constructed from
the output of build tools operating on build artifacts, and these may
not exist when doing a make clean.
So avoid evaluating them eagerly, to prevent spurious build warnings.
Suggested-by: Pedro Falcato <pedro.falcato@gmail.com>
Tested-by: Alan Bartlett <ajb@elrepo.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Add two helper functions for calling PCS methods. phylink_pcs_config()
allows us to handle PCS configuration specifics in one location, rather
than the two call sites. phylink_pcs_link_up() gives us consistency.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q1TzK-007Exd-Rs@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Epping says:
====================
net: phy: mscc: support VSC8501
this updated series of patches adds support for the VSC8501 Ethernet
PHY and fixes support for the VSC8502 PHY in cases where no other
software (like U-Boot) has initialized the PHY after power up.
The first patch simply adds the VSC8502 to the MODULE_DEVICE_TABLE,
where I guess it was unintentionally missing. I have no hardware to
test my change.
The second patch adds the VSC8501 PHY with exactly the same driver
implementation as the existing VSC8502.
The (new) third patch removes phydev locking from
vsc85xx_rgmii_set_skews(), as discussed for v2 of the patch set.
The (now) fourth patch fixes the initialization for VSC8501 and VSC8502.
I have tested this patch with VSC8501 on hardware in RGMII mode only.
https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/VSC8501-03_Datasheet_60001741A.PDFhttps://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/VSC8502-03_Datasheet_60001742B.pdf
Table 4-42 "RGMII CONTROL, ADDRESS 20E2 (0X14)" Bit 11 for each of
them.
By default the RX_CLK is disabled for these PHYs. In cases where no
other software, like U-Boot, enabled the clock, this results in no
received packets being handed to the MAC.
The patch enables this clock output.
According to Microchip support (case number 01268776) this applies
to all modes (RGMII, GMII, and MII).
Other PHYs sharing the same register map and code, like
VSC8530/31/40/41 have the clock enabled and the relevant bit 11 is
reserved and read-only for them. As per previous discussion the
patch still clears the bit on these PHYs, too, possibly more easily
supporting other future PHYs implementing this functionality.
For the VSC8572 family of PHYs, having a different register map,
no such changes are applied.
====================
Link: https://lore.kernel.org/r/20230523153108.18548-1-david.epping@missinglinkelectronics.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Holding the struct phy_device (phydev) lock is unnecessary when
accessing phydev->interface in the PHY driver .config_init method,
which is the only place that vsc85xx_rgmii_set_skews() is called from.
The phy_modify_paged() function implements required MDIO bus level
locking, which can not be achieved by a phydev lock.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC8501 PHY can use the same driver implementation as the VSC8502.
Adding the PHY ID and copying the handler functions of VSC8502 is
sufficient to operate it.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Chuck Lever says:
====================
Bug fixes for net/handshake
Paolo observed that there is a possible leak of sock->file. I
haven't looked into that yet, but it seems to be separate from
the fixes in this series, so no need to hold these up.
====================
The submissions mentions net-next but it means netdev (perhaps
merge window left over when trees are converged). In any case,
it should have gone into net, but was instead applied to net-next
as commit deb2e484ba ("Merge branch 'net-handshake-fixes'").
These are fixes tho, and Chuck needs them to make progress with
the client so double-merging them into net... it is what it is :(
Link: https://lore.kernel.org/r/168381978252.84244.1933636428135211300.stgit@91.116.238.104.host.secureserver.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable the upper layer protocol to specify the SNI peername. This
avoids the need for tlshd to use a DNS lookup, which can return a
hostname that doesn't match the incoming certificate's SubjectName.
Fixes: 2fd5532044 ("net/handshake: Add a kernel API for requesting a TLSv1.3 handshake")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If user space never calls DONE, sock->file's reference count remains
elevated. Enable sock->file to be freed eventually in this case.
Reported-by: Jakub Kacinski <kuba@kernel.org>
Fixes: 3b3009ea8a ("net/handshake: Create a NETLINK service for handling handshake requests")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 3b3009ea8a ("net/handshake: Create a NETLINK service for handling handshake requests")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
trace_handshake_cmd_done_err() simply records the pointer in @req,
so initializing it to NULL is sufficient and safe.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 3b3009ea8a ("net/handshake: Create a NETLINK service for handling handshake requests")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If get_unused_fd_flags() fails, we ended up calling fput(sock->file)
twice.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Fixes: 3b3009ea8a ("net/handshake: Create a NETLINK service for handling handshake requests")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
handshake_req_submit() now verifies that the socket has a file.
Fixes: 3b3009ea8a ("net/handshake: Create a NETLINK service for handling handshake requests")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZG4AiAAKCRDbK58LschI
g+xlAQCmefGbDuwPckZLnomvt6gl4bkIjs7kc1ySbG9QBnaInwD/WyrJaQIPijuD
qziHPAyx+MEgPseFU1b7Le35SZ66IwM=
=s4R1
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-05-24
We've added 19 non-merge commits during the last 10 day(s) which contain
a total of 20 files changed, 738 insertions(+), 448 deletions(-).
The main changes are:
1) Batch of BPF sockmap fixes found when running against NGINX TCP tests,
from John Fastabend.
2) Fix a memleak in the LRU{,_PERCPU} hash map when bucket locking fails,
from Anton Protopopov.
3) Init the BPF offload table earlier than just late_initcall,
from Jakub Kicinski.
4) Fix ctx access mask generation for 32-bit narrow loads of 64-bit fields,
from Will Deacon.
5) Remove a now unsupported __fallthrough in BPF samples,
from Andrii Nakryiko.
6) Fix a typo in pkg-config call for building sign-file,
from Jeremy Sowden.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf, sockmap: Test progs verifier error with latest clang
bpf, sockmap: Test FIONREAD returns correct bytes in rx buffer with drops
bpf, sockmap: Test FIONREAD returns correct bytes in rx buffer
bpf, sockmap: Test shutdown() correctly exits epoll and recv()=0
bpf, sockmap: Build helper to create connected socket pair
bpf, sockmap: Pull socket helpers out of listen test for general use
bpf, sockmap: Incorrectly handling copied_seq
bpf, sockmap: Wake up polling after data copy
bpf, sockmap: TCP data stall on recv before accept
bpf, sockmap: Handle fin correctly
bpf, sockmap: Improved check for empty queue
bpf, sockmap: Reschedule is now done through backlog
bpf, sockmap: Convert schedule_work into delayed_work
bpf, sockmap: Pass skb ownership through read_skb
bpf: fix a memory leak in the LRU and LRU_PERCPU hash maps
bpf: Fix mask generation for 32-bit narrow loads of 64-bit fields
samples/bpf: Drop unnecessary fallthrough
bpf: netdev: init the offload table earlier
selftests/bpf: Fix pkg-config call building sign-file
====================
Link: https://lore.kernel.org/r/20230524170839.13905-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phone features a notification LED connected to the pmi632. Configure
the RGB led found on it.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v3-2-079d2cada699@z3ntu.xyz
The PMI632, commonly found on SoCs with SDM632 has various standard
functions like ADC, GPIOs, LPG and more.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v3-1-079d2cada699@z3ntu.xyz
The SHIFT6mq (axolotl) is an SDM845-based smartphone with 2 flash LEDs.
One LED is white, the other one is yellow. Define both LEDs in the DTS
so they can be used as flash or torch and enable the flash LED
controller to control them in PMI8998.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230518133113.273880-4-me@dylanvanassche.be
Qualcomm PMIC PMI8998 has a 3 channel flash LED driver which is used
by many phones for 1 or 2 flash LEDs. Each LED can be used in flash mode
or torch mode. Add the flash LED controller node to PMI8998 DTS.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230518133113.273880-3-me@dylanvanassche.be
Some of the regulators must be always-on to ensure correct operation of
the system, e.g. PM8916 L2 for the LPDDR RAM, L5 for most digital I/O
and L7 for the CPU PLL (strictly speaking the CPU PLL might only need
an active-only vote but this is not supported for regulators in
mainline currently).
The RPM firmware seems to enforce that internally, these supplies stay
on even if we vote for them to power off (and there is no other
processor running). This means it's pointless to keep sending
enable/disable requests because they will just be ignored.
Also, drivers are much more likely to get a wrong impression of the
regulator status, because regulator_is_enabled() will return false when
there are no users, even though the regulator is always on.
Describe this properly by marking the regulators as always-on.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-8-54d4960a05fc@gerhold.net
Right now each MSM8916 device has a huge block of regulator constraints
with allowed voltages for each regulator. For lack of better
documentation these voltages are often copied as-is from the vendor
device tree, without much extra thought.
Unfortunately, the voltages in the vendor device trees are often
misleading or even wrong, e.g. because:
- There is a large voltage range allowed and the actual voltage is
only set somewhere hidden in some messy vendor driver. This is often
the case for pm8916_{l14,l15,l16} because they have a broad range of
1.8-3.3V by default.
- The voltage is actually wrong but thanks to the voltage constraints
in the RPM firmware it still ends up applying the correct voltage.
To have proper regulator constraints it is important to review them in
context of the usage. The current setup in the MSM8916 device trees
makes this quite hard because each device duplicates the standard
voltages for components of the SoC and mixes those with minor
device-specific additions and dummy voltages for completely unused
regulators.
The actual usage of the regulators for the SoC components is in
msm8916-pm8916.dtsi, so it can and should also define the related
voltage constraints. These are not board-specific but defined in the
APQ8016E/PM8916 Device Specification. The board DT can then focus on
describing the actual board-specific regulators, which makes it much
easier to review and spot potential mistakes there.
Note that this commit does not make any functional change. All used
regulators still have the same regulator constraints as before. Unused
regulators do not have regulator constraints anymore because most of
these were too broad or even entirely wrong. They should be added back
with proper voltage constraints when there is an actual usage.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-7-54d4960a05fc@gerhold.net
Goal of the msm8916-pm8916.dtsi is to reduce the boilerplate necessary
to create a device tree for a typical board with the MSM8916 SoC
combined with the PM8916 PMIC. > 99% of all MSM8916 boards use the same
standard setup where many of the PM8916 regulators have a fixed purpose
and only some are left up for board-specific use.
While MSM8916 (and perhaps MSM8939 soon) is currently the only platform
with such an include, it has definitely proven useful. With more than
30 boards using it (not all of them upstream yet) it simplifies the
review a lot and reduces the chance of configuring the standard
components incorrectly.
In preparation of extending its scope slightly, add a comment at the
top that clearly explains what the .dtsi represents and when it should
(or should not) be used.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-6-54d4960a05fc@gerhold.net
Some of the power supplies for the analog audio codec in PM8916 are
wired externally. While most boards use the regulators currently
specified in pm8916.dtsi, in theory it could be connected differently.
We already have msm8916-pm8916.dtsi that models that standard setup
used by most devices so move the -supply properties there and keep
the base pm8916.dtsi independent.
Currently all MSM8916 boards in mainline make use of
msm8916-pm8916.dtsi, so it is not necessary to adjust any other boards.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-5-54d4960a05fc@gerhold.net
Not every device has something connected to the digital audio codec
in MSM8916 and/or the analog audio codec in PM8916. Disable those by
default so the hardware is only powered up when necessary.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-4-54d4960a05fc@gerhold.net
The regulator constraints for most MSM8916 devices (except DB410c) were
originally taken from Qualcomm's msm-3.10 vendor device tree (for lack
of better documentation). Unfortunately it turns out that Qualcomm's
voltages are slightly off as well and do not match the voltage
constraints applied by the RPM firmware.
This means that we sometimes request a specific voltage but the RPM
firmware actually applies a much lower or higher voltage. This is
particularly critical for pm8916_l11 which is used as SD card VMMC
regulator: The SD card can choose a voltage from the current range of
1.8 - 2.95V. If it chooses to run at 1.8V we pretend that this is fine
but the RPM firmware will still silently end up configuring 2.95V.
This can be easily reproduced with a multimeter or by checking the
SPMI hardware registers of the regulator.
Fix this by making the voltages match the actual "specified range" in
the PM8916 Device Specification which is enforced by the RPM firmware.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-3-54d4960a05fc@gerhold.net
The 96Boards specification expects a 1.8V power rail on the low-speed
expansion connector that is able to provide at least 0.18W / 100 mA.
According to the DB410c hardware user manual this is done by connecting
both L15 and L16 in parallel with up to 55mA each (for 110 mA total) [1].
Unfortunately the current regulator setup in the DB410c device tree
does not implement the specification correctly and only provides 5 mA:
- Only L15 is marked always-on, so L16 is never enabled.
- Without specifying a load the regulator is put into LPM where
it can only provide 5 mA.
Fix this by:
- Adding proper voltage constraints for L16.
- Making L16 always-on.
- Adding regulator-system-load for both L15 and L16. 100 mA should be
available in total, so specify 50 mA for each. (The regulator
hardware can only be in normal (55 mA) or low-power mode (5 mA) so
this will actually result in the expected 110 mA total...)
[1]: https://www.96boards.org/documentation/consumer/dragonboard/dragonboard410c/hardware-docs/hardware-user-manual.md.html#power-supplies
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 828dd5d66f ("arm64: dts: apq8016-sbc: make 1.8v available on LS expansion")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-2-54d4960a05fc@gerhold.net
For some reason DB410c has completely bogus regulator constraints that
actually just correspond to the programmable voltages which are already
provided by the regulator driver. Some of them are not just outside the
recommended operating conditions of the APQ8016E SoC but even exceed
the absolute maximum ratings, potentially risking permanent device
damage.
In practice it's not quite as dangerous thanks to the RPM firmware:
It turns out that it has its own voltage constraints and silently
clamps all regulator requests. For example, requesting 3.3V for L5
(allowed by the current regulator constraints!) still results in 1.8V
being programmed in the actual regulator hardware.
Experimentation with various voltages shows that the internal RPM
voltage constraints roughly correspond to the safe "specified range"
in the PM8916 Device Specification (rather than the "programmable
range" used inside apq8016-sbc.dtsi right now).
Combine those together with some fixed voltages used in the old
msm-3.10 device tree from Qualcomm to give DB410c some actually valid
voltage constraints.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 4c7d53d16d ("arm64: dts: apq8016-sbc: add regulators support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
Add QUP(SPI / I2C) peripheral, PRNG, WDOG and the remaining UART nodes.
While at it, enable the SPI NOR in RDP433 board.
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230517072806.13170-1-quic_kathirav@quicinc.com
MDP in sm8550.dtsi is not disabled (although its parent MDSS is), so
board DTS does not have to enable it.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516154539.238655-2-krzysztof.kozlowski@linaro.org
Enable the Display Clock Controller by default in SoC DTSI so unused
clocks can be turned off. It does not require any external resources,
so as core SoC component should be always available to boards.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516154539.238655-1-krzysztof.kozlowski@linaro.org
Enable PM8550 PMIC flash LED controller and add two flash LEDs using
four current outputs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516150202.188655-3-krzysztof.kozlowski@linaro.org
Somehow wifi was placed further up in the file than where it should be.
Move it down so the nodes are sorted by reg again.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516-sm6350-order-v1-1-5c3b7c4cd761@fairphone.com
We need more granularity for things like the GPU. Add the missing levels.
This unfortunately requires some re-indexing, resulting in an ugly diff.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516005306.952821-1-konrad.dybcio@linaro.org
Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform.
The laptop design is similar to trogdor in the choice of primary
components but the specifics on usage of those differ slightly.
Add the devicetree for the laptop with support for most of the
hardware present.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515093744.289045-5-nikita@trvn.ru
mdss is useless without a display controller which makes explicitly
enabling mdp redundant. Have it enabled by default to drop the extra
node for all users.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515093744.289045-3-nikita@trvn.ru
lpass clocks are usually blocked from HLOS by the firmware and
instead are managed by the ADSP. Mark them as reserved and explicitly
enable in the CrOS boards that have special, cooperative firmware.
The IDP board gets lpass clocks disabled as it doesn't make use of sound
anyway and might use Qualcomm firmware that blocks those clocks. [1]
[1] https://lore.kernel.org/all/ZBJhmDd3zK%2FAiwBD@google.com/
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515093744.289045-2-nikita@trvn.ru
It's possible to use this device with a (non-standard) hub to get USB
working in host mode, but dr_mode="peripheral" prevents the UDC to
do so.
Remove dr_mode="peripheral" and add usb-role-switch so that it defaults
to otg mode and can be switched to host mode in userspace.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/TYZPR04MB632102315884225B7343533B96729@TYZPR04MB6321.apcprd04.prod.outlook.com