GIC child node is supposed to be named msi-controller:
sa8295p-adp.dtb: interrupt-controller@17a00000: gic-its@17a40000: False schema does not allow
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417080939.28648-3-krzysztof.kozlowski@linaro.org
Qualcomm PCI express root complex does not use snps,dw-pcie fallback:
['qcom,pcie-sm8150', 'snps,dw-pcie'] is too long
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417080939.28648-2-krzysztof.kozlowski@linaro.org
Since commit 6c84bbd103 ("dt-bindings: arm-smmu: Add generic
qcom,smmu-500 bindings") the SMMU is supposed to use qcom,smmu-500
compatible fallback.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417080939.28648-1-krzysztof.kozlowski@linaro.org
Drop incorrect and unused serial properties - address/size-cells and
reg-names:
sa8155p-adp.dtb: geniqup@ac0000: serial@a84000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'reg-names' were unexpected)
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417080818.28398-1-krzysztof.kozlowski@linaro.org
Enable the always-on subsystem controller on SA8775P platforms for use
by upcoming support for other peripherals.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230504161755.197417-2-brgl@bgdev.pl
Now that the hypervisor issue is fixed, we can add the watchdog node
for sa8775p platforms.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230427161218.201828-1-brgl@bgdev.pl
Introduce sdam_0 node, which is to be used via nvmem for power on
reasons during reboot. Add supported PoN reaons supported via sdam_0
node.
Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417145536.414490-4-brgl@bgdev.pl
On this PMIC, the PON peripheral does not provide passing reboot modes
over HLOS. They must be passed over SDAM. Remove the reboot-mode
properties as we'll provide a proper SDAM node in a later commit.
Fixes: d2d9a59274 ("arm64: dts: qcom: sa8775p: add the Power On device node")
Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230417145536.414490-2-brgl@bgdev.pl
Enable the UFS and its PHY on sa8775p-ride.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230411130446.401440-6-brgl@bgdev.pl
Add nodes for the UFS and its PHY on sa8775p platforms.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230411130446.401440-5-brgl@bgdev.pl
The F(x)tec Pro1X is a mobile phone released by FX Technologies Ltd
in 2022.
The phone is exactly the same as the Pro1 released in 2019 with some
changes:
- MSM8998 -> SM6115
- Camera button is no longer multistate
- Only one 48MP back camera
- A new keyboard layout picked by the community.
This commit has the following features working:
- Display (using simplefb)
- UFS
- Power and volume buttons
- Pinctrl
- RPM Regulators
- USB (Device Mode)
To get a successful boot run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/\
sm6115-fxtec-pro1x.dtb > .Image.gz-dtb
mkbootimg --kernel .Image.gz-dtb \
--ramdisk initrd.img \
--base 0x0 \
--kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 \
--second_offset 0xf00000 \
--tags_offset 0x100 \
--pagesize 4096 \
--cmdline "CMDLINE HERE" \
-o qx1050-boot.img
fastboot flash boot qx1050-boot.img
fastboot erase dtbo
fastboot reboot
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230505-fxtec-pro1x-support-v3-2-0c9c7f58b205@riseup.net
Pass to dev_err_probe() PTR_ERR from actual dev_pm_opp_find_bw_floor()
call which failed, instead of previous ret which at this point is 0.
Failure of dev_pm_opp_find_bw_floor() would result in prematurely ending
the probe with success.
Fixes smatch warnings:
drivers/soc/qcom/icc-bwmon.c:776 bwmon_probe() warn: passing zero to 'dev_err_probe'
drivers/soc/qcom/icc-bwmon.c:781 bwmon_probe() warn: passing zero to 'dev_err_probe'
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202305131657.76XeHDjF-lkp@intel.com/
Cc: <stable@vger.kernel.org>
Fixes: b9c2ae6cac ("soc: qcom: icc-bwmon: Add bandwidth monitoring driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230513111747.132532-1-krzysztof.kozlowski@linaro.org
Enable both the MACs found on the board.
ethernet0 and ethernet1 both ultimately go to a series of on board
switches which aren't managed by this processor.
ethernet0 is connected to a Marvell 88EA1512 phy via RGMII. That goes to
the series of switches via SGMII on the "media" side of the phy.
RGMII_SGMII mode is enabled via devicetree register descriptions.
The switch on the "media" side has auto-negotiation disabled, so
configuration from userspace similar to:
ethtool -s eth0 autoneg off speed 1000 duplex full
is necessary to get traffic flowing on that interface.
ethernet1 is in a mac2mac/fixed-link configuration going to the same
series of switches directly via RGMII.
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501205105.2518373-3-ahalaney@redhat.com
This platform has 2 MACs integrated in it, go ahead and describe them.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230501205105.2518373-2-ahalaney@redhat.com
n_bytes variable in the driver represents the number of bytes per word
that needs to be sent/copied to fifo. Bits/word can be between 8 and 32
bits from the client but in memory they are a power of 2, same is mentioned
in spi.h header:
"
* @bits_per_word: Data transfers involve one or more words; word sizes
* like eight or 12 bits are common. In-memory wordsizes are
* powers of two bytes (e.g. 20 bit samples use 32 bits).
* This may be changed by the device's driver, or left at the
* default (0) indicating protocol words are eight bit bytes.
* The spi_transfer.bits_per_word can override this for each transfer.
"
Hence, round of n_bytes to a power of 2 to avoid values like 3 which
would generate unalligned/odd accesses to memory/fifo.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Fixes: a51acc2400 ("spi: dw: Add support for 32-bits max xfer size")
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-4-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Store address width capabilities of DMA controller during init and check
the same per transfer to make sure the bits/word requirement can be met.
Current DW DMA driver requires both tx and rx channel to be configured
and functional hence a subset of both tx and rx channel address width
capability is checked with the width requirement(n_bytes) for a
transfer.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-3-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Check capabilities of DMA controller during init to make sure it is
capable of handling MEM2DEV for tx channel, DEV2MEM for rx channel.
Current DW DMA driver requires both tx and rx channel to be configured
and functional for any kind of transfers to take effect including
half duplex. Hence, check for both tx and rx direction and fail on
unavailbility of either.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-2-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Enable SAI3 on i.MX8MP EVK, add WM8960 codec binding and regulator.
This is all that is needed to get analog audio output operational
on i.MX8MP EVK.
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add all SAI nodes, SDMA2 and SDMA3 nodes, and AudioMIX node. This is
needed to get audio operational on i.MX8MP .
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon-kit
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I'm leaving Cirrus Logic, and will no longer have access to
hardware and documentation necessary to be effective in a
maintainership role.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230512154503.741718-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
Flush the SoundWire interrupt handler work instead of cancelling it.
When a SoundWire interrupt is triggered the pm_runtime is held
until the work has completed. It's therefore unsafe to cancel
the work, it must be flushed.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230512144237.739000-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
The imx8m Mini and imx8m Nano both use the same CSIS driver for
interfacing with sensors and cameras. The Mini routes the CSIS
output to the imx7-CSI driver, and the Nano routes the CSIS
through the imx8-isi driver like the one used on the imx8mp.
Enable the drivers necessary to facilitate capture on both of
these two platforms.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The baseboard has a very specific pinout for the TD Next 5640
camera which uses an OV5640 sensor. Enable it as part of the
deveopment kit baseboard instead of an overlay.
Enable the camera with the following
media-ctl -l "'ov5640 1-0010':0 -> 'csis-32e30000.mipi-csi':0 [1]"
media-ctl -v -V "'ov5640 1-0010':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -v -V "'crossbar':0 [fmt:UYVY8_1X16/640x480 field:none]"
media-ctl -v -V "'mxc_isi.0':0 [fmt:UYVY8_1X16/640x480 field:none]"
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CSI in the imx8mn is the same as what is used in the imx8mm,
but it's routed to the ISI on the Nano. Add both the ISI and CSI
nodes, and pointing them to each other. Since the CSI capture is
dependent on an attached camera, mark both ISI and CSI as
disabled by default.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
updated the code to trigger the IRQ when the FIFO was half empty,
overlapping filling more data into the FIFO and sending what is left.
This appears to cause regressions on the Zynq 7000, for transactions
longer than the FIFO size, below that no overlapping occurs.
It would appear from my testing that any attempt to put new data into
the FIFO whilst data is still transmitting causes data corruption
on both send and receive. If I am reading the commit message right
on commit 49530e6411 ("spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()"), that would also seem to imply this is the
case.
On the assumption that this isn't an issue on the platform
the original slave mode support was added for, update the
cdns_transfer_one to only set the watermark to 50% of the FIFO size
when in slave mode. There by retaining the new behaviour for slave
mode but reverting to the older behaviour when the SPI is used a
master.
Fixes: b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230509164153.3907694-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
Recent changes to cdns_spi_irq introduced some issues.
Firstly, when writing the end of a longer transaction, the code in
cdns_spi_irq will write data into the TX FIFO, then immediately
fall into the if (!xspi->tx_bytes) path and attempt to read data
from the RX FIFO. However this required waiting for the TX FIFO to
empty before the RX data was ready.
Secondly, the variable trans_cnt is now rather inaccurately named
since in cases, where the watermark is set to 1, trans_cnt will be
1 but the count of bytes transferred would be much longer.
Finally, when setting up the transaction we set the watermark to 50%
of the FIFO if the transaction is great than 50% of the FIFO. However,
there is no need to split a tranaction that is smaller than the
whole FIFO, so anything up to the FIFO size can be done in a single
transaction.
Tidy up the code a little, to avoid repeatedly calling
cdns_spi_read_rx_fifo with a count of 1, and correct the three issues
noted above.
Fixes: b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230509164153.3907694-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
This fixes a copy & paste error.
No functional change intended, BUCK1_ENMODE_MASK equals BUCK2_ENMODE_MASK.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Originally-from: Robin Gong <yibin.gong@nxp.com
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de
Link: https://lore.kernel.org/r/20230512081935.2396180-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org
Topology could have more instances of the tokens being searched for than
the number of sets that need to be copied. Stop copying token after the
limit of number of token instances has been reached. This worked before
only by chance as we had allocated more size for the tuples array than
the number of actual tokens being parsed.
Fixes: 7006d20e5e ("ASoC: SOF: Introduce IPC3 ops")
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512114630.24439-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
If there are failures in DSP runtime resume, the device state will not
reach active and this makes it impossible e.g. to retrieve a possible
DSP panic dump via "exception" debugfs node. If
CONFIG_SND_SOC_SOF_DEBUG_ENABLE_DEBUGFS_CACHE=y is set, the data in
cache is stale. If debugfs cache is not used, the region simply cannot
be read.
To allow debugging these scenarios, update the debugfs cache contents in
resume error handler. User-space can then later retrieve DSP panic and
other state via debugfs (requires SOF debugfs cache to be enabled in
build).
Reported-by: Curtis Malainey <cujomalainey@chromium.org
Link: https://github.com/thesofproject/linux/issues/4274
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512104638.21376-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Remove Krzysztof Kozlowski from maintainer of Samsung SoC Audio drivers
and change the status to maintenance (no one is reality being paid for
looking at this).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com
Link: https://lore.kernel.org/r/20230513090228.4340-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org
When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.
The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.
Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)
At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk
The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed.
Fixes: 55b423d562 ("ASoC: mediatek: mt8186: support audio clock control in platform driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/20230511092437.1.I31cceffc8c45bb1af16eb613e197b3df92cdc19e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org
The commands in sof_ipc_dai_config.flags are encoded as bits:
1 (bit0) - hw_params
2 (bit1) - hw_free
4 (bit2) - pause
These are commands, they cannot be combined as one would assume, for
example
3 (bit0 | bit1) is invalid.
This can happen right at the second start of a stream as at the end of the
first stream we set the hw_free command (bit1) and on the second start we
would OR on top of it the hw_params (bit0).
Fixes: b66bfc3a98 ("ASoC: SOF: sof-audio: Fix broken early bclk feature for SSP")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Link: https://lore.kernel.org/r/20230512110317.5180-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
When an error occurs, we need to make sure the device can pm_runtime
suspend instead of keeping it active.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
When an error occurs, we need to make sure the device can pm_runtime
suspend instead of keeping it active.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
When a firmware IPC error happens during a pm_runtime suspend, we
ignore the error and suspend anyways. However, the code
unconditionally increases the runtime_pm counter. This results in a
confusing configuration where the code will suspend, resume but never
suspend again due to the use of pm_runtime_get_noresume().
The intent of the counter increase was to prevent entry in D3, but if
that transition to D3 is already started it cannot be stopped. In
addition, there's no point in that case in trying to prevent anything,
the firmware error is handled and the next resume will re-initialize
the firmware completely.
This patch changes the logic to prevent suspend when the device is
pm_runtime active and has a use_count > 0.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com
Link: https://lore.kernel.org/r/20230512103315.8921-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
These registers enable the HDaudio DMA hardware to split/merge data
from different PDIs, possibly on different links.
This capability exists for all types of HDaudio extended links, but
for now is only required for SoundWire. In the SSP/DMIC case, the IP
is programmed by the DSP firmware.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
We defined the values but never initialized it for SoundWire/SSP, fix
this miss.
A Fixes: tag is not provided as instance_offset was not used so far,
so nothing was really broken. This patch is only required for the
SoundWire support in the following patch.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
We mix the use of hlink->ml_addr and the 'ml_addr' parameter. It's the
same thing, let's align on using the parameter.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com
Reviewed-by: Rander Wang <rander.wang@intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512174611.84372-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org