Convert s5p-mfc bindings to DT schema format using json-schema.
Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230328114729.61436-1-aakarsh.jain@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Set the read_label() callback to return a friendly name provided in DT
(firmware), in order to make in_{therm,voltage}X_label attributes show
up in sysfs for userspace to consume a channel name. This is
particularly useful for custom thermistors being attached to otherwise
generically named GPIOs, where the name is known by the board DT.
If the channel name isn't set in DT, use the datasheet_name hardcoded in
the driver instead.
Note that this doesn't fall back to fwnode_get_name() as that provides
suboptimally readable names, with an @xx address suffix from board DT.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230502-iio-adc-propagate-fw-node-label-v3-5-6be5db6e6b5a@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since the migration to fwnode_get_name in commit 4f47a236a2 ("iio:
adc: qcom-spmi-adc5: convert to device properties") the resulting
adc5_channel_prop::channel_name (renamed from datasheet_name in the
previous patch) - which is propagated into iio_chan_spec::extend_name -
was containing the DT node name including @xx suffix if a "label"
property is not present, while adc5_channels::datasheet_name was thus
far set by the macros but always remained unread. Put it to use instead
of using a confusing name containing @xx in sysfs filenames (again, when
"label" is not set).
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230502-iio-adc-propagate-fw-node-label-v3-3-6be5db6e6b5a@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_chan_spec::datasheet_name expects a channel/pin name on the hardware
part, i.e. from its datasheet, instead of a friendly name from DT which
typically describes the use of said channel. GPIO channels are commonly
specialized in QCOM board DTS based on what a - typically thermistor -
is connected to.
Also rename adc5_channel_prop::datasheet_name to channel_name to that
effect.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230502-iio-adc-propagate-fw-node-label-v3-2-6be5db6e6b5a@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As mentioned and discussed in [1] extend_name should not be used for
full channel labels (and most drivers seem to only use it to express a
short type of a channel) as this affects sysfs filenames, while the
label name is supposed to be extracted from the *_label sysfs file
instead. This appears to have been unclear to some drivers as
extend_name is also used when read_label is unset, achieving an initial
goal of providing sensible names in *_label sysfs files without noticing
that sysfs filenames are (negatively and likely unintentionally)
affected as well.
Point readers of iio_chan_spec::extend_name to iio_info::read_label by
mentioning deprecation and side-effects of this field.
[1]: https://lore.kernel.org/linux-arm-msm/20221221223432.si2aasbleiicayfl@SoMainline.org/
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230502-iio-adc-propagate-fw-node-label-v3-1-6be5db6e6b5a@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Devices which may take a while to initialize during probe and which have
no strong reason to probe synchronously can request asynchronous probing
as default probe strategy. This can speed-up start times on some
platforms.
The KX022A gets probe delayed for at least two reasons. It enables the
supply regulator, (which is likely to have ramp-up delay if it was
disabled) and additionally it delays while the sensor itself is
initializing.
Changing to asynchronous probing may cause problems. Some of which are
discussed in:
https://lore.kernel.org/all/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk/
Enable asynchronous probing for KX022A.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/24cea76c282a28b7a4dba297ab627176f8097907.1683185765.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Devices which may take a while to initialize during probe and which have
no strong reason to probe synchronously can request asynchronous probing
as default probe strategy. This can speed-up start times on some
platforms.
The BU27034 gets probe delayed for at least two reasons. It enables the
supply regulator, (which is likely to have ramp-up delay if it was
disabled) and additionally it delays while the sensor itself is
initializing.
Changing to asynchronous probing may cause problems. Some of which are
discussed in:
https://lore.kernel.org/all/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk/
Enabling async probing for the ROHM BU27034 should be fairly safe to try
though as there is no in-tree users for it yet. If the async probing
appears to be an issue we can switch easily back to synchronous (or
better yet, fix the actual problem).
Enable asynchronous probing for BU27034.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/e7088793e1868c77b1894b30cd026e8ed043ea7c.1683185765.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As discussed in [1] it is more convenient to use a generic `channel`
node name for ADC channels while storing a friendly - board-specific
instead of PMIC-specific - name in the label, if/when desired to
overwrite the channel description already contained (but previously
unused) in the driver [2].
The same `channel` node name pattern has also been set in
iio/adc/adc.yaml, but this generic binding is not inherited as base for
qcom,spmi-vadc bindings due to not having any other generic elements in
common, besides the node name rule and reg property.
Replace the .* name pattern with the `channel` literal, but leave the
label property optional for bindings to choose to fall back a channel
label hardcoded in the driver [2] instead.
[1]: https://lore.kernel.org/linux-arm-msm/20221106193018.270106-1-marijn.suijten@somainline.org/T/#u
[2]: https://lore.kernel.org/linux-arm-msm/20230116220909.196926-4-marijn.suijten@somainline.org/
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230410202917.247666-6-marijn.suijten@somainline.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Just cosmetics. No functional change intended...
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230216101452.591805-4-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver uses the continuous mode of the chip and integration
time can be configured through sysfs.
The constants for calculating lux value differs between packaging
so it uses different compatible string for the two versions
"ti,opt4001-picostar" and "ti,opt4001-sot-5x3" since the device id
is the same.
Datasheet: https://www.ti.com/lit/gpn/opt4001
Signed-off-by: Stefan Windfeldt-Prytz <stefan.windfeldt-prytz@axis.com>
Link: https://lore.kernel.org/r/20230323-add-opt4001-driver-v3-2-62e121dab294@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since nearly all stm32 dt's are using the legacy adc channel config,
we should warn users about using it.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20230421083858.2613289-1-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This sensor can be found as CALS0001 on the Lenovo Yoga
Tablet 2 series.
Tested on a Lenovo Yoga Tablet 2 1051-F.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230420232631.68864-1-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Same as the lsm9ds0, except that the lsm303d doesn't
feature a gyroscope.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-7-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Per its datasheet, the LSM303D also features that pin.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-6-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lsm303d can be found as ACCL0001 on various Lenovo devices,
including the Lenovo Yoga Tablet 2 1051-F, where I tested this
patch.
Dropped SPI support as per discussion in thread linked below.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-5-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lsm303d is basically the lsm9ds0 without the gyroscope
(which the LSM9DS0 IMU driver doesn't handle), as far as I
can tell.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-4-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lsm303d has the same register mapping as the lsm9ds0,
thus we can just re-use that.
Tested on a Lenovo Yoga Tablet 2 1051-F.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-3-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The lsm303d has the same register mapping as the lsm9ds0,
thus we can just re-use that.
Tested on a Lenovo Yoga Tablet 2 1051-F.
Signed-off-by: Marius Hoch <mail@mariushoch.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20230415231130.115094-2-mail@mariushoch.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The channel ADC5_USB_IN_V_16 is using 1/16 pre-scaling on at least
pm7250b and pmi632. Allow that in the schema.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v1-5-fe94dc414832@z3ntu.xyz
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On success, ad74413r_get_single_adc_result() returns IIO_VAL_INT aka
1. So currently, the IIO_CHAN_INFO_PROCESSED case is effectively
equivalent to the IIO_CHAN_INFO_RAW case, and we never call
ad74413r_adc_to_resistance_result() to convert the adc measurement to
ohms.
Check ret for being negative rather than non-zero.
Fixes: fea251b6a5 (iio: addac: add AD74413R driver)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230503095817.452551-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Although this property is used right now for IIO_CHAN_INFO_SCALE,
this ADC has two internal reference voltages, which the driver currently
doesn't make use of.
Fixes: db73419d8c ("dt-bindings: iio: adc: Add binding documentation for NXP IMX8QXP ADC")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230424092312.61746-1-alexander.stein@ew.tq-group.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If only adc differential channels are defined driver will fail with
stm32-adc: probe of 48003000.adc:adc@0 failed with error -22
Fix this by skipping the initialization if no channels are defined.
This applies only to the legacy way of initializing adc channels.
Fixes: d7705f3544 ("iio: adc: stm32-adc: convert to device properties")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20230503162029.3654093-2-sean@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If no adc differential channels are defined driver will fail with EINVAL:
stm32-adc: probe of 48003000.adc:adc@0 failed with error -22
Fix this by skipping the initialization if no channels are defined.
This applies only to the legacy way of initializing adc channels.
Fixes: d7705f3544 ("iio: adc: stm32-adc: convert to device properties")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20230503162029.3654093-1-sean@geanix.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7192 provides a specific channel configuration where both negative
and positive inputs are connected to AIN2. This was represented in the
ad7192 driver as a IIO channel with .channel = 2 and .extended_name set
to "shorted".
The problem with this approach, is that the driver provided two IIO
channels with the identifier .channel = 2; one "shorted" and the other
not. This goes against the IIO ABI, as a channel identifier should be
unique.
Address this issue by changing "shorted" channels to being differential
instead, with channel 2 vs. itself, as we're actually measuring AIN2 vs.
itself.
Note that the fix tag is for the commit that moved the driver out of
staging. The bug existed before that, but backporting would become very
complex further down and unlikely to happen.
Fixes: b581f748cc ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Co-developed-by: Alisa Roman <alisa.roman@analog.com>
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230330102100.17590-1-paul@crapouillou.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When apply_acpi_orientation() fails, st_accel_common_probe() will fall back
to iio_read_mount_matrix(), which checks for a mount-matrix device property
and if that is not set falls back to the identity matrix.
But when a sensor has no ACPI companion fwnode, or when the ACPI fwnode
does not have a "_ONT" method apply_acpi_orientation() was returning 0,
causing iio_read_mount_matrix() to never get called resulting in an
invalid mount_matrix:
[root@fedora ~]# cat /sys/bus/iio/devices/iio\:device0/mount_matrix
(null), (null), (null); (null), (null), (null); (null), (null), (null)
Fix this by making apply_acpi_orientation() always return an error when
it did not set the mount_matrix.
Fixes: 3d8ad94bb1 ("iio: accel: st_sensors: Support generic mounting matrix")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Marius Hoch <mail@mariushoch.de>
Link: https://lore.kernel.org/r/20230416212409.310936-1-hdegoede@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO ABI mandates expressing integration times in seconds. The GTS
helper errorneously uses micro seconds in integration_times_available.
Fix this by converting the lists to IIO_VAL_INT_PLUS_MICRO.
Fixes: 38416c28e1 ("iio: light: Add gain-time-scale helpers")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/eeacd192c259e885850b5a2dd8b776bccfc44fa8.1681722914.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bu27034 uses micro seconds for integration time configuration. This
is incorrect as the ABI mandates use of seconds.
Change BU27034 driver to use seconds for integration time.
Fixes: e52afbd610 ("iio: light: ROHM BU27034 Ambient Light Sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/a05647669af22ba919c7c87dccb43975e3235a87.1681722914.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The kerneldoc for iio_gts_find_sel_by_int_time() has an error.
Documentation states that function is searching a selector for a HW-gain
while it is searching a selector for an integration time.
Fix the documentation by saying the function is looking for a selector
for an integration time.
Fixes: 38416c28e1 ("iio: light: Add gain-time-scale helpers")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/ZEIjI4YUzqPZk/9X@fedora
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Valid values for "adc_chan" are zero to (PALMAS_ADC_CH_MAX - 1).
Smatch detects some buffer overflows caused by this:
drivers/iio/adc/palmas_gpadc.c:721 palmas_gpadc_read_event_value() error: buffer overflow 'adc->thresholds' 16 <= 16
drivers/iio/adc/palmas_gpadc.c:758 palmas_gpadc_write_event_value() error: buffer overflow 'adc->thresholds' 16 <= 16
The effect of this bug in other functions is more complicated but
obviously we should fix all of them.
Fixes: a99544c6c8 ("iio: adc: palmas: add support for iio threshold events")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/14fee94a-7db7-4371-b7d6-e94d86b9561e@kili.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Smatch reports:
drivers/iio/adc/mxs-lradc-adc.c:766 mxs_lradc_adc_probe() warn:
missing unwind goto?
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f8 ("iio: adc: mxs-lradc: Add support for ADC driver")
Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad4130 driver registers a clock provider, but never removes it. This
leaves a stale clock provider behind that references freed clocks when the
device is unbound.
Register a managed action to remove the clock provider when the device is
removed.
Fixes: 62094060cf ("iio: adc: ad4130: add AD4130 driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230414150702.518441-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The tmag5273 gets a runtime PM reference before reading a measurement and
releases it when done. But if the measurement fails the tmag5273_read_raw()
function exits before releasing the reference.
Make sure that this error path also releases the runtime PM reference.
Fixes: 866a138917 ("iio: magnetometer: add ti tmag5273 driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230414013752.498767-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The scale value of ibus and ibat on the datasheet is incorrect due to the
customer report after the experimentation with some specific vendor ID
chips.
Fixes: c1404d1b65 ("iio: adc: mt6370: Add MediaTek MT6370 support")
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/1681122862-1994-1-git-send-email-chiaen_wu@richtek.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The problem is these lines:
ret = vref_uv = regulator_get_voltage(adc->vref);
if (ret < 0)
The "ret" variable is type long and "vref_uv" is u32 so that means
the condition can never be true on a 64bit system. A negative error
code from regulator_get_voltage() would be cast to a high positive
u32 value and then remain a high positive value when cast to a long.
The "ret" variable only ever stores ints so it should be declared as
an int. We can delete the "vref_uv" variable and use "ret" directly.
Fixes: 7d02296ac8 ("iio: adc: add imx93 adc support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/Y+utEvjfjQRQo2QB@kili
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reset pin was wrongly assigned due to a copy/paste error,
fix it to match actual gpio pin.
While at it, remove a blank line from nanopi r5s dts.
Fixes: 0562003140 ("arm64: dts: rockchip: Add FriendlyARM NanoPi R5C")
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20230510161850.4866-1-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20230513135307.26554-2-cnsztl@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Each of the LEDs on the RGxx3 which is currently controlled via GPIO
can also be controlled via a PWM. Change each of the LEDs to PWM so
that users have the ability to adjust the brightness of the LEDs
according to their preference.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20230512191633.33416-1-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the Anbernic RG353PS. This device is identical in form
factor to the RG353P and has the following hardware differences:
- No touchscreen is present on i2c2 (or at all).
- Only contains 1GB of RAM.
- Has no eMMC.
- Only appears to ship with the 2nd revision of the display panel.
Note that the display panel has been added to the st7703 panel driver
in a separate commit series.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20230512162039.31132-3-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree binding for Anbernic RG353PS. This device is identical
to the RG353P, except it does not have a touchscreen, does not have
an eMMC, only includes 1GB of RAM, and ships with only the 2nd
revision panel based on a Sitronix ST7703 controller. Support for the
panel has been added in a separate commit.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230512162039.31132-2-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Hao Lan says:
====================
net: hns3: fix some bug for hns3
There are some bugfixes for the HNS3 ethernet driver. patch#1 fix miss
checking for rx packet. patch#2 fixes VF promisc mode not update
when mac table full bug, and patch#3 fixes a nterrupts not
initialization in VF FLR bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeout of the cmdq reset command has been increased to
resolve the reset timeout issue in the full VF scenario.
The timeout of other cmdq commands remains unchanged.
Fixes: 8d307f8e8c ("net: hns3: create new set of unified hclge_comm_cmd_send APIs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.
According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.
Fixes: 6988eb2a9b ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>