pll_p_out4 is used on all/most Tegra boards to drive the cdev2 output pin
to provide a reference clock to a ULPI USB PHY. This reference clock must
run at 24MHz, and the cdev2 output has no additional dividers.
Remove board-paz00.c's now-duplicate initialization of this clock.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 40f9cf0 "ARM: tegra: reparent sclk to pll_c_out1" changed the
rate of hclk. Since pclk is derived from that, and only has integer
dividers, the pclk rate needs to change in the same fashion, from 54MHz
to 60MHz.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_p_out4 needs to be used for other purposes. Reparent sclk so that
it runs from pll_c. Change sclk's rate to 120MHz from 108MHz since this
is the lowest precise rate that can be achieved by dividing the pll_c
rate without reducing the sclk rate. (600/5=120, 600/5.5=109.0909...,
600/6=100).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
pll_c will be used as a clock source. Fill in tegra_pll_c_freq_table[]
so that it's possible to explicitly initialize the PLL.
NVIDIA's downstream nv-3.1 kernel and the ChromeOS kernel have different
pll_c tables. nv-3.1 contains entries for 522MHz and 598MHz output,
whereas the ChromeOS kernel contains entries for 600MHz output. I chose
to upstream the ChromeOS values for now, since the 600MHz rate appears
to match the default rate of this PLL when the HW boots, and it's not
clear to me why 522 or 598MHz are more useful.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[swarren: wrote commit description]
Add WM8903 codec nodes, and top-level sound complex node for basic
analog audio over headset jack and internal speakers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Both the Tegra30 I2S and AHUB modules used clocks, and hence currently
require AUXDATA in order to get specific device names so that clock
lookups work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Set up the audio clock tree for Tegra30 in an equivalent fashion to the
existing setup for Tegra20.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
pll_a uses pll_p_out1 as its parent. Therefore this clock needs to be
initialized to make sure pll_a has a known input clock. Failure to do so
will cause the system to crash early in the bootup.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra30 AHUB driver must call tegra_periph_reset_deassert() for all
devices on the AHUB's configlink bus. The AHUB driver must be able to
call clk_get_sys() to retrieve the clock parameter for this function.
Add the necessary clock aliases to allow this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Print an explicit error message in various failure cases to allow
easier diagnosis.
WARN_ON() some internal failures that users/clients shouldn't be able to
trigger.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
After an error interrupt setting cmd->err, I see another interrupt that
the data engine is empty which clears cmd->err before being processed.
So, clear cmd->err at the beginning of a transfer only to handle these
consecutive interrupts.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
They're equivalent, but SEEK_SET is more informative...
Cc: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Bernie Thompson <bernie@plugable.com>
CC: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Petko Manolov <petkan@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Nomadik variant is somewhere inbetween the U300 and the Ux500
variant, its actually expose the same primecell ID as the U300
but had different characteristics so it needs a small revision
bump and hard-coding from the board/device tree. After this it
works just fine.
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add calls to tracehook_report_syscall_{entry,exit} and tracehook_signal_handler
Signed-off-by: Steven Walter <stevenrwalter@gmail.com>
Signed-off-by: Wade Farnsworth <wade_farnsworth@mentor.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Supplying the asm-generic/syscall.h interface is a
pre-requisite for HAVE_ARCH_TRACEHOOK
Signed-off-by: Steven Walter <stevenrwalter@gmail.com>
Signed-off-by: Wade Farnsworth <wade_farnsworth@mentor.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ThumbEE probe code uses inline assembly to read ID_PFR0 in order to
detect whether ThumbEE is implemented by the processor.
This patch replaces the inline asm with the read_cpuid_ext macro.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Return -ENOMEM if the kmalloc() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1ce7b9349f ("USB: serial: reuse generic write urb and
bulk-out buffer") the port write_urb is simply a pointer to the first
member of write_urbs so there's no need to kill it twice.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case. This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface data should not be used as a flag to signal disconnect.
Now that all serial drivers use the usb_serial disconnect flag and
mutex, we can set the interface data prior to registering the ports and
there's no need to clear it at disconnect.
This should hopefully also make it more clear that the interface data is
not a flag, which could prevent future misuse.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix abuse of interface data which was used to signal device disconnect.
Use the usb_serial disconnect flag and mutex where appropriate.
Note that tiocmget does not need to check for disconnect as it does not
access the device.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix abuse of interface data which was used to signal device disconnect.
Note that neither tiocmset or tiocmget need to check for disconnect as
they do not access the device.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix abuse of interface data which was used to signal device disconnect.
Use the usb_serial disconnect flag and mutex where appropriate.
Note that tiocmget does not need to check for disconnect as it does not
access the device.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to share code between the current server upcall mechanism
and the new gssproxy upcall mechanism introduced in a following patch.
Signed-off-by: Simo Sorce <simo@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Fix up some broken printk strings that were spanning multiple lines,
making it hard to search for them.
Cc: Manohar Vanga <manohar.vanga@cern.ch>
Cc: Martyn Welch <martyn.welch@ge.com>
Cc: "Emilio G. Cota" <cota@braap.org>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes this beauty into a statement that actually has an effect on amd64.
Tested-by: Per Jessen <per@opensuse.org>
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This file contains only the most generic elements. Other
class specific and device specific ABI documents will follow
over time.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take the core support + the kfifo buffer implentation out of
staging. Whilst we are far from done in improving this subsystem
it is now at a stage where the userspae interfaces (provided by
the core) can be considered stable.
Drivers will follow over a longer time scale.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Step 1 in moving the IIO core out of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just a couple of things I came across whilst reviewing this file for
moving out of staging. I doubt anyone cares, but seemed sensible to fix
them now!
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two attributes are only used in the one driver. Whilst they
are fairly general I'm not entirely happy committing to them at
this stage.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is one device supported by the driver which is not listed in the Kconfig
help test. This patch adds it. Also we are past the point were we can possible
fit all devices supported by the driver in the Kconfig entry title, so just list
the initial device that was supported by this driver and note that similar
devices are supported as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AD5662 is compatible to the AD5660, but uses an external
reference instead of an internal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can not read back the value from the device, but we cache the value anyway so
we might as well return the cached value instead of an error.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devices supported by this drivers only have a single shift register, which
contains both the power down mode and the output sample. So writing the power
down mode and the output sample can be done by the same function. Call this
function prepare_write as it will prepare the spi message for a write. Also
introduce a small helper function which performs the whole write by calling the
chip the specific prepare function followed by a spi_sync.
The two power down bits are always placed ontop of the msb of the output sample,
so we can easily calculate their position by adding the channels shift to the
channels realbits.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use extended channel attributes instead of raw sysfs files for the additional
channel attributes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>