Introduce a private per-port data structure for the mxpcie driver and
replace the shared flexible array of registered lines with an array of
per-port objects.
This prepares the driver for storing per-port state needed by subsequent
features.
No functional change intended.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-14-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx_trig_bytes sysfs attribute currently relies on 8250-internal
helper functions and assumes a fixed mapping between trigger levels and
FIFO behavior.
Some UARTs provide hardware-specific RX trigger mechanisms that do not
fit this model. Add optional uart_port callbacks for setting and getting
the RX trigger level, and use them when provided, while preserving the
existing 8250 helpers as the default fallback.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-13-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On MUEx50, break signaling under RS485 requires a driver-specific
sequence and cannot be handled correctly by the generic 8250 break
implementation alone.
Implement a mxpcie break_ctl callback that performs MUEx50-specific
break handling when RS485 is enabled and fall back to the default 8250
break handling for other modes.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-12-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UARTs require driver-specific handling for break signaling, which
cannot be expressed by the generic 8250 break implementation alone.
Add an optional uart_port break_ctl callback and route
serial8250_break_ctl() through it when provided. Rename the existing
8250 implementation to serial8250_do_break_ctl() and export it so
low-level drivers can reuse the default 8250 behavior when appropriate.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-11-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moxa PCIe multiport serial boards support switching the serial interface
mode between RS232, RS422, RS485-2W, and RS485-4W via on-board control
registers.
Implement an rs485_config() callback and map TIOCSRS485 requests to the
corresponding hardware modes using serial_rs485 flags:
- RS232 = (no flags set)
- RS422 = SER_RS485_ENABLED | SER_RS485_MODE_RS422
- RS485_2W (half-duplex) = SER_RS485_ENABLED
- RS485_4W (full-duplex) = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX
This allows users to reconfigure the serial mode at runtime via ioctl().
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-10-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART provides a memory-mapped TX FIFO data window along with
a TX FIFO level counter.
Fill the TX FIFO in bulk via the MMIO FIFO window based on available
FIFO space, using uart_port_tx_limited() for the common serial-core TX
handling.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-9-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART provides a memory-mapped RX FIFO data window along with
an RX FIFO byte counter.
When no break or error conditions are present, read received data in
bulk via the MMIO FIFO window and push it to the tty layer in one
operation. Fall back to the generic 8250 RX path for break and error
handling.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-8-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a mxpcie-specific handle_irq() implementation for Moxa PCIe serial
ports.
This keeps the interrupt handling self-contained in the driver and
provides a hook point for MUEx50-specific RX/TX paths added in subsequent
patches. The handler processes RX, updates modem status, and handles TX
when THRE is asserted.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-7-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART can handle in-band software flow control (XON/XOFF)
directly in hardware.
Program the on-chip XON/XOFF characters from termios settings and enable
the corresponding MUEx50 flow control modes when IXON or IXOFF is
requested. Provide throttle and unthrottle callbacks so RX can be
stopped and resumed cleanly.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-6-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART supports automatic RTS/CTS flow control via the enhanced
feature register.
Implement a mxpcie-specific set_termios() callback that enables MUEx50
auto-RTS/auto-CTS when CRTSCTS is requested and disables it otherwise.
Keep the 8250 port status flags in sync with the hardware configuration.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-5-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MUEx50 UART provides an enhanced register set and programmable FIFO
trigger levels for RX, TX, and flow control.
Enable enhanced mode during port startup and program the MUEx50 FIFO
trigger registers according to the configured port settings. Clear the
programmed state again during shutdown to restore the default UART
configuration.
The TX FIFO write pointer and read pointer are driven by different
clocks. Clear the FIFOs repeatedly during startup so both pointers are
reset before programming the trigger levels.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-4-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new 8250 port type for the Moxa MUEx50 UART and describe its basic
FIFO size and trigger characteristics in the 8250 port configuration
table.
The 8250_mxpcie driver sets UPF_FIXED_TYPE and uses PORT_MUEX50 so that
the generic 8250 core applies the correct defaults.
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Link: https://patch.msgid.link/20260731074820.735619-3-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Moxa PCIe multiport serial boards are currently handled as part of
8250_pci.c. In preparation for adding Moxa-specific UART features and
optimizations, move the Moxa PCIe implementation into a dedicated
driver.
This introduces drivers/tty/serial/8250/8250_mxpcie.c and wires it up
via Kconfig and Makefile, while preserving the existing probe flow and
device IDs.
This change was suggested during earlier reviews by Andy Shevchenko [1][2].
No functional change intended.
Link: https://lore.kernel.org/all/ZmQovC6TbDpTb3c8@surfacebook.localdomain/ [1]
Link: https://lore.kernel.org/all/CAHp75VeDsVt0GQYUFxLM+obfmqXBPa3hM3YMsFbc26uzWZG-SQ@mail.gmail.com/ [2]
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://patch.msgid.link/20260731074820.735619-2-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver implements its own helper to select the performance level
corresponding to a requested baud rate. The helper duplicates
functionality already provided by geni_se_set_perf_level() in the GENI
core.
Replace the local implementation with the common helper and remove the
associated duplicate definitions and code. This consolidates
performance-level management in the GENI framework and reduces driver
specific code.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260801-reuse_common_geni_framework_helpers-v2-3-13753256ef71@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To manage GENI serial engine resources during runtime power
management, drivers currently need to call functions for ICC, clock,
and SE resource operations in both suspend and resume paths, resulting
in code duplication across drivers.
The new geni_se_resources_activate() and geni_se_resources_deactivate()
helper APIs addresses this issue by providing a streamlined method to
enable or disable all resources based, thereby eliminating redundancy
across drivers.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260801-reuse_common_geni_framework_helpers-v2-2-13753256ef71@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART driver maintains local helpers for resource and power-domain
initialisation that duplicate functionality already provided by the common
GENI framework.
Replace the driver-specific implementations with geni_se_resources_init()
and geni_se_domain_attach(), and use the power-domain list stored in
struct geni_se. This reduces code duplication and centralises GENI resource
management without functional changes.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260801-reuse_common_geni_framework_helpers-v2-1-13753256ef71@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_console_write_atomic() runs from nbcon atomic context, where
sleeping is not allowed. It calls clk_enable(), which takes the common-clk
enable_lock. Under PREEMPT_RT that is a sleeping lock:
clk_enable_lock() first tries spin_trylock_irqsave(), but on contention
falls back to spin_lock_irqsave(). Therefore, an atomic-context printk on
an RT kernel with a clk-backed pl011 can trip:
BUG: sleeping function called from invalid context at spinlock_rt.c:48
__might_resched from rt_spin_lock
rt_spin_lock from clk_enable_lock
clk_enable_lock from clk_enable
clk_enable from pl011_console_write_atomic
... from vprintk_emit
This was found and reproduced on PREEMPT_RT. Arm32 and arm64 DT SoCs are
affected; arm64 SBSA/ACPI has no clk, so clk_enable(NULL) short-circuits
before the lock. In addition, write_atomic() may be invoked from NMI
context and is documented to avoid locking. Removing clk_enable() from
the callback also avoids a potentially unsafe NMI acquisition of the
common-clock enable_lock.
An nbcon atomic-capable console must be printable from any context, so
the clock cannot be gated between writes. Enable the clock while the
console is available for output: use clk_prepare_enable() in
pl011_console_setup(), release it via clk_disable_unprepare() in the
console .exit() callback, and drop the per-write clk_enable()/clk_disable()
pairs from write_atomic() and write_thread().
When printk suspends consoles, drop the reference after
uart_suspend_port() stops console access and restore it before
uart_resume_port() -- but only if suspend actually marked the port
suspended (a wake-capable tty stays running and must keep its clock), and
keep it when console_suspend_enabled is false so no_console_suspend works.
The active power cost of keeping the clock enabled is platform-dependent:
none where the UART clock is a fixed always-on oscillator, real where it
is a gateable clock branch, which then cannot be gated (nor possibly can
its parent clocks) while the console is available for output. When serial
core actually suspends the port, the reference is released so the clock
provider can gate the clock tree.
Fixes: 2eb2608618 ("serial: amba-pl011: Implement nbcon console")
Suggested-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/all/8733xeaxix.fsf@jogness.linutronix.de/
Assisted-by: Claude:claude-fable-5
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Link: https://patch.msgid.link/20260724213348.77418-3-kmehltretter@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_console_setup() calls clk_prepare() on the UART clock, but the
console provides no matching teardown, so the clock is never unprepared
when the console is unregistered -- via the sysfs "console" attribute or
a driver unbind. Each re-registration prepares the clock again, leaking
one prepare reference per cycle.
Even where preparing the clock has no hardware effect, the stale
reference leaves the clock framework's prepare count unbalanced. For
providers with prepare/unprepare operations or runtime-PM integration,
it may also retain resources after the console is unregistered.
Add a console .exit() callback that clk_unprepare()s the clock,
balancing the clk_prepare() in pl011_console_setup().
Fixes: 4b4851c65d ("clk: amba-pl011: convert to clk_prepare()/clk_unprepare()")
Assisted-by: Claude:claude-fable-5
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Link: https://patch.msgid.link/20260724213348.77418-2-kmehltretter@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AST2600 and AST2700 VUART controllers are identical to the AST2500
VUART controller.
Add the "aspeed,ast2600-vuart" and "aspeed,ast2700-vuart" compatible
strings and fall back to "aspeed,ast2500-vuart" for compatibility with
the existing driver.
Signed-off-by: Yu-Che Hsieh <yc_hsieh@aspeedtech.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260721-upstream-ast2700-vuart-support-v1-1-b4ed612b1aa2@aspeedtech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Genio board DTs provide serial aliases for all enabled UARTs, but
the MTK 8250 driver still registered every port with the default line
number. If uart0 deferred and another UART probed first, the 8250 core
could still assign ttyS0 to the wrong port despite the DT aliases.
Read the serial alias during OF probe and seed uart.port.line before
registering the port so the 8250 core reserves the requested ttyS slot.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20260727-ccaione-genio-serial-aliases-v2-2-0f2ae41a8e89@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On most MediaTek boards only serial0 is aliased, so the remaining
enabled uarts get first-free ttyS line numbers from the 8250 core in
probe order. When the console uart defers on its clocks another uart can
win line 0: console=ttyS0 then ends up on the wrong port and the boot
looks like a hang on the serial console, depending on probe order.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> # kukui & asurada-hayato
Link: https://patch.msgid.link/20260727-ccaione-genio-serial-aliases-v2-1-0f2ae41a8e89@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last mentions of this driver on local Linux and telco support forums
date back to 2011. This does not prove that no users remain, but the
likelihood is too low to justify continuing to carry the driver in the
kernel.
The maintainer agreed that the driver should be removed and noted that it
is simple enough to build as an external module if a user resurfaces [1].
Remove the driver along with its Kconfig, defconfig, build and MAINTAINERS
entries.
[1] https://lore.kernel.org/linux-serial/20260218152330.GI26902@suse.cz/
Assisted-by: Codex:GPT-5.6
Signed-off-by: Qingfang Deng <qingfang.deng@linux.dev>
Reviewed-by: David Sterba <dsterba@suse.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Link: https://patch.msgid.link/20260803091938.259944-1-qingfang.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vt_setactivate() function accepts any mode value without validation,
while VT_SETMODE correctly rejects invalid values (only VT_AUTO and
VT_PROCESS are valid).
This allows users to set invalid mode values (e.g., 0xFF) which bypasses
VT_PROCESS signal handling and causes undefined VT switching behavior.
Fix this by adding the same validation as VT_SETMODE.
Signed-off-by: Wang Zihan <jiyu03@qq.com>
Link: https://patch.msgid.link/tencent_6A7DAE2E1288663D23AACBE2950D6E535007@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GENI main sequencer handles console TX while the secondary sequencer
handles FIFO RX. Before nbcon, the legacy console writer disabled both
interrupt domains while it performed a long polled M-side transfer. This
left the small S-side FIFO unserviced, allowing console input to overrun
and be lost.
The nbcon conversion replaces IRQ masking with the UART port lock, but a
threaded console write still prevents the RX handler from draining the
FIFO. Keep S-side RX enabled independently of M-side TX and drain it
while refilling each bounded console command. This preserves interactive
input during console output.
Atomic output masks only M-side TX state, leaving FIFO RX handling
independent. The threaded writer can also detect a SysRq character while
it drains RX, so defer delivery until device_unlock() drops the UART port
lock, as the existing IRQ path does with uart_unlock_and_check_sysrq().
Assisted-by: OpenCode:GPT-5.5
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://patch.msgid.link/20260729-qcom-geni-nbcon-v1-2-3053b96465ed@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy GENI console writer serializes every message around a
synchronous polled M-side transfer. It blocks printk callers for UART
wire time and cannot provide atomic output while normal console output is
active.
Convert the console to nbcon threaded and atomic writers. Use the UART
port lock as the device lock and bound threaded M-side commands so
urgent diagnostics can take over atomic output. The threaded writer is
batching the output in 32-source-byte commands, a value chosen to
balance the command setup overhead with atomic-handoff latency.
Atomic output can cancel an active normal TX command. Use irq_work to
resume queued TTY output afterward, honor flow control, and prevent the
deferred restart from accessing the port during shutdown or removal.
Assisted-by: OpenCode:GPT-5.5
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://patch.msgid.link/20260729-qcom-geni-nbcon-v1-1-3053b96465ed@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently relies on qcom_geni_serial_pm() through the
uart_ops.pm callback to manage runtime PM references. However, the
callback has a void return type, so failures from
pm_runtime_resume_and_get() cannot be propagated to the caller.
As a result, startup() may continue and access hardware even when the
runtime PM resume operation failed, leading to register accesses while
the device is not powered.
Move runtime PM acquisition to qcom_geni_serial_startup() and release it
to qcom_geni_serial_shutdown(). Since startup() can return an error, PM
resume failures are now detected and propagated before any hardware
initialization is performed. The startup/shutdown pair also provides a
natural place to balance runtime PM references for normal port usage.
During probe, uart_add_one_port() may configure the port before any user
opens the TTY, meaning startup() has not yet been called. To keep the
hardware powered during port registration, acquire a runtime PM
reference with pm_runtime_resume_and_get() before uart_add_one_port()
and release it with pm_runtime_put() afterwards.
By moving runtime PM handling out of uart_ops.pm, resume failures are no
longer silently ignored and all hardware accesses are guaranteed to
occur while the device is powered.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260720-remove_uart_change_state-v2-1-30153ce4333b@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver doesn't really need to split the registration of the GPIO
chip into stages, as platform_device_info already provides fields for
the firmware node, parent device and the software node. Use
platform_device_register_full() and simplify the code. This also
addresses the problem with incorrect reference count of the assigned
firmware node.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260728-exar-pdev-reg-full-v1-1-7a96e77309e1@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coccinelle warns about missing clk_put on the error path after clk_get,
but the error path returns with an ERR_PTR where clk_put must not be
called. Restructure into a single if block so the logic is clear to
silence false positive coccinelle warning.
Commit 580d952e44 ("tty: serial: bcm63xx: fix missing clk_put() in
bcm63xx_uart") previously tried to fix this same warning by adding a
clk_put, which was reverted because it was wrong.
Prevent anyone from making the same mistake again.
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://patch.msgid.link/604886147edb67c3ed85b192eb3f7a4a6dd0f0ac.1784788388.git.xiaopei01@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Google Tensor G5 SoC (known as "laguna" and canonically written in
code as "lga") has a UART based on Designware IP. The UART appears to
work reasonably well, at least for serial console, with the existing
driver in Linux. Add a compatible for this UART based on the canonical
"lga" name for this SoC with a fallback to the existing
"snps,dw-apb-uart".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://patch.msgid.link/20260722-contrib-pg-pixel10-initial-dts-v2-2-3abae9717feb@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The minimum baud rate supported by this driver is 0, so even for the B0
case, uart_get_baud_rate() will return 9600, not zero. This check is no
longer necessary since commit 16ae2a877b ("serial: Fix crash if the
minimum rate of the device is > 9600 baud") so remove it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260720193411.3517484-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The minimum baud rate supported by this driver is 0, so even for the B0
case, uart_get_baud_rate() will return 9600, not zero. This check is no
longer necessary since commit 16ae2a877b ("serial: Fix crash if the
minimum rate of the device is > 9600 baud") so remove it.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260720195147.3630241-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3d9e6f556e.
The 8250 driver no longer depends on @oops_in_progress and
will no longer violate the port->lock locking constraints.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://patch.msgid.link/20260729120439.281252-3-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the necessary callbacks to switch the 8250 console driver
to perform as an nbcon console.
Add implementations for the nbcon console callbacks:
->write_atomic()
->write_thread()
->device_lock()
->device_unlock()
and add CON_NBCON to the initial @flags.
All hardware access in the callbacks is within unsafe sections.
The ->write_atomic() and ->write_thread() callbacks allow safe
handover/takeover per byte and add a preceding newline if they
take over from another context mid-line.
For the ->write_atomic() callback, a new irq_work is used to defer
modem control since it may be called from a context that does not
allow waking up tasks. During suspend/resume the irq_work is not
used as this has been shown to cause suspend problems for some
hardware. Upon resume, any pending modem control is performed.
Note: A new __serial8250_clear_IER() is introduced for direct
clearing of UART_IER during console writing (which will not be
holding the port lock for atomic printing or KDB/KGDB). This
allows restoring a lockdep check to serial8250_clear_IER() in
a follow-up commit.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260729120439.281252-2-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inclusion of <linux/kconfig.h> in commit 7ab80d1e72 ("serial: 8250:
fix compile error with hub6_match_port() when compiled as a module") is
unneeded as it's guaranteed by the build starting from commit 2a11c8ea20
("kconfig: Introduce IS_ENABLED(), IS_BUILTIN() and IS_MODULE()").
Remove it here.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260721144847.3728422-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inclusion of <linux/kconfig.h> in commit f18643843b ("serial:
max310x: fix compile errors if CONFIG_SPI_MASTER is disabled") is
unneeded as it's guaranteed by the build starting from the commit
2a11c8ea20 ("kconfig: Introduce IS_ENABLED(), IS_BUILTIN() and
IS_MODULE()"). Remove it here.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260721144420.3727708-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d338ab1d90.
uart_console() only indicates that the port is selected as the console.
It does not mean that the console has already been registered or has
printed the buffered messages.
On platforms where an initial 8250 port is replaced when the real UART
device is registered, clearing CON_PRINTBUFFER causes the console to
start at the end of the printk ring buffer. Without earlycon, all
messages logged before UART registration are therefore lost.
Fixes: d338ab1d90 ("serial: 8250: Clear CON_PRINTBUFFER on port re-registration")
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Anirudh Srinivasan <asrinivasan@oss.tenstorrent.com>
Link: https://lore.kernel.org/all/20260522101042.21976-1-fushuai.wang@linux.dev/
Signed-off-by: Fushuai Wang <wangfushuai@baidu.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260724093151.53216-1-fushuai.wang@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please consider pulling these changes from the signed vfs-7.2-rc5.fixes tag.
Thanks!
Christian
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCamYljAAKCRCRxhvAZXjc
ogWyAPwORZDIIsRiAQbnPs+OkYszuWCY29OeUrTf+m3z+tBTLwD+NUFtpH5XIcYJ
3jHtGXPoHjEaOVsNyIdxwnOxWfo+6ws=
=VNq0
-----END PGP SIGNATURE-----
Merge tag 'vfs-7.2-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- vfs: Preserve the ACL_DONT_CACHE state in forget_cached_acl().
ACL_DONT_CACHE is meant to be a permanent opt-out from ACL caching
which FUSE relies on for servers that don't negotiate FUSE_POSIX_ACL.
The helper replaced it with ACL_NOT_CACHED, silently re-enabling the
cache, and as fuse doesn't invalidate the cache for such servers a
properly timed get_acl() returned stale ACLs. Comes with a fuse
selftest reproducing this.
- pidfs:
- Preserve PIDFD_THREAD when a thread pidfd is reopened via
open_by_handle_at(). PIDFD_THREAD shares the O_EXCL bit which
do_dentry_open() strips after the flags have been validated, so
the reopened pidfd silently became a process pidfd. Comes with a
selftest.
- Add a pidfs_dentry_open() helper so the regular pidfd allocation
path and the file handle path share the code that forces O_RDWR
and reapplies the pidfd flags that do_dentry_open() strips.
- Handle FS_IOC32_GETVERSION in the compat ioctl path.
- Make pidfs_ino_lock static.
- iomap:
- Fix the block range calculation in ifs_clear_range_dirty() so a
partial clear doesn't drop the dirty state of blocks the range
only partially covers.
- Support invalidating partial folios so a partial truncate or hole
punch with blocksize < foliosize doesn't leave stale dirty bits
behind.
- Only set did_zero when iomap_zero_iter() actually zeroed
something.
- Guard ifs_set_range_dirty() and ifs_set_range_uptodate() against
zero-length ranges where the unsigned last-block calculation
underflows and bitmap_set() writes far beyond the ifs->state
allocation.
- Don't merge ioends with different io_private values as the merge
could leak or corrupt the private data of the individual ioends.
- exec:
- Raise bprm->have_execfd only once the binfmt_misc interpreter has
actually been opened. The flag was set as soon as a matching 'O'
or 'C' entry was found. If the interpreter open failed with
ENOEXEC the exec fell through to the next binary format with
have_execfd raised but no executable staged and begin_new_exec()
NULL derefed past the point of no return.
- Fix an unsigned loop counter wrap in transfer_args_to_stack() on
nommu. An overlong argument or environment string pushes bprm->p
below PAGE_SIZE, the stop index becomes zero, and the loop never
terminates, wrapping its counter and copying garbage from in
front of the page array into the new process stack.
- Make binfmt_elf_fdpic only honour the first PT_INTERP like
binfmt_elf does. Each additional PT_INTERP overwrote the previous
interpreter, leaking the name allocation and the interpreter file
reference together with the write denial open_exec() took,
leaving the file unwritable for as long as the system runs.
- overlayfs:
- Compare the full escaped xattr prefix including the trailing dot.
An xattr like "trusted.overlay.overlayfoo" was misclassified as
an escaped overlay xattr.
- Check read access to the copy_file_range() source with the
source's mounter credentials.
- super: Thawing a filesystem whose block device was frozen with
bdev_freeze() deadlocked. Dropping the last block layer freeze
reference from under s_umount ends up in fs_bdev_thaw() which
reacquires s_umount on the same task. Pin the superblock with an
active reference instead and call bdev_thaw() without holding
s_umount.
- procfs: Return EACCES instead of success when the ptrace access check
for namespace links fails.
- afs: Use afs_dir_get_block() rather than afs_dir_find_block() for
block 0 in afs_edit_dir_remove(), matching afs_edit_dir_add().
- Push the memcg gating of ->nr_cached_objects() down into the btrfs
and shmem callbacks instead of skipping every callback during
non-root memcg reclaim. The blanket check short-circuited XFS whose
inode reclaim hook is intentionally driven from per-memcg contexts to
free memcg-charged slab.
- eventpoll: Pin files while checking reverse paths.
Since struct file became SLAB_TYPESAFE_BY_RCU a concurrent close
could free and recycle the file under the check which then took and
dropped the f_lock of whatever live file now occupies that slot.
* tag 'vfs-7.2-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (24 commits)
super: fix emergency thaw deadlock on frozen block devices
pidfs: make pidfs_ino_lock static
eventpoll: pin files while checking reverse paths
fs: push nr_cached_objects memcg gating into individual filesystems
afs: Fix afs_edit_dir_remove() to get, not find, block 0
iomap: prevent ioend merge when io_private differs
iomap: add comments for ifs_clear/set_range_dirty()
iomap: fix out-of-bounds bitmap_set() with zero-length range
iomap: fix incorrect did_zero setting in iomap_zero_iter()
iomap: support invalidating partial folios
iomap: correct the range of a partial dirty clear
fs/super: fix emergency thaw double-unlock of s_umount
pidfs: handle FS_IOC32_GETVERSION in compat ioctl
ovl: check access to copy_file_range source with src mounter creds
proc: Fix broken error paths for namespace links
pidfs: add pidfs_dentry_open() helper
selftests/pidfd: check PIDFD_THREAD survives open_by_handle_at()
pidfs: preserve thread pidfds reopened by file handle
ovl: fix trusted xattr escape prefix matching
selftests/fuse: add ACL_DONT_CACHE regression test
...
Just a couple of small bits for the SpacemiT driver - one small fix, and
a new compatible in the DT binding.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmpmL3sACgkQJNaLcl1U
h9CDnwgAggPOeUHMrQWYES7f74oTVl/kt0B1TBV6g91r8a4p0yyy7Kn6C1njBQ7n
N5bgSL2EkpQRjj2d5akh42Apwb5EQZMdqICo68XElWnk0AxH6Y1PdRkfcruU9PnS
t7KJEeBxdsZAJhx5ZEWZrIwjY/rbEvI+rfePgdm8kVeUUVs4ur6Zg1DNk/LgolOP
xr60E5DWHIczjJ3Ae+svL5mmJ8FICFOThAYjMzGyRACB4c3znMBhzKVoNrUR6sl5
7qSf1x3WBXIYwd0RRs9YhTF6vQhlnfKfu8rPfb2S6v8rE7JmmokLr3kVFzgpph1K
o893VMecWe5al0ZuE2qdf44w2Ohv0Q==
=2PTr
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Just a couple of small bits for the SpacemiT driver - one small fix,
and a new compatible in the DT binding"
* tag 'spi-fix-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dt-bindings: spacemit: add K3 SPI compatible
spi: spacemit: Correct TX FIFO slot calculation
One driver specific fix where one of the MediaTek drivers duplicated
some core code buggily, and a core fix for an ordering issue on startup
where we could end up configuring a voltage outside of constraints due
to the order in which we applied constraints.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmpmMC4ACgkQJNaLcl1U
h9DoiAf/V64CUAFspev+AtzWpx1Su9zZoSzoMM5Gj0WBuMoo4G5hZj804DQ/n8al
sai+f0loMEVcblfpZNOlYagSkDgvvIc/1SQrAQ1oIxMbpotE1vn4htzGsJJuwwgL
lh5GC4CsrXOSRX3VG6pJeBR6RTb9VEbkAhLoxKAJyPlcynk2KdBPwR9B1ZlCgpe6
MP2WrurEVexvuDlZdE8THYth4FXCms0uH5VLo+Q3G4r1Ayt9YpvbvG91fzJSJGti
NAzAWma2GFGwQkka5sgMYHyP6rwM1vJ71mz+Bq9G5fUe6DyEp85jv993D5lq2vbH
69GO6ZTZmruCqOkDEELIKA4EpKYzZA==
=3XbV
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One driver specific fix where one of the MediaTek drivers duplicated
some core code buggily, and a core fix for an ordering issue on
startup where we could end up configuring a voltage outside of
constraints due to the order in which we applied constraints"
* tag 'regulator-fix-v7.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: clamp voltage constraints before applying apply_uV
regulator: mt6358: use regmap helper to read fixed LDO calibration
Here are a number of small char/misc/etc. driver fixes for 7.2-rc5 that
resolve a bunch of different reported issues. Included in here are:
- rust_binder error message reporting fix
- stratix10-svc firmware driver fixes
- mei driver fix
- intel_th hardware tracing driver fix
- comedi driver fix
- uio_hv_generic driver fix
- ntsync selftest fix
- nsm misc driver fix
- some MAINTAINER file updates
All of these have been in linux-next for over a week with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCamYCHg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTpwCgyyS6niRHf2Y0qx/o+i8s87h+ipoAoJeaOzb7
RWX/ZYiUEoQCtfbxmXZF
=cRG6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small char/misc/etc driver fixes for 7.2-rc5 that
resolve a bunch of different reported issues. Included in here are:
- rust_binder error message reporting fix
- stratix10-svc firmware driver fixes
- mei driver fix
- intel_th hardware tracing driver fix
- comedi driver fix
- uio_hv_generic driver fix
- ntsync selftest fix
- nsm misc driver fix
- some MAINTAINER file updates
All of these have been in linux-next for over a week with no reported
issues"
* tag 'char-misc-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: Update wine-devel list address
rust_binder: only print failure if error has source
intel_th: fix MSC output device reference leak
misc: nsm: pin the module while the device is open
mei: bus: access mei_device under device_lock on cleanup
misc: nsm: only unlock nsm_dev on post-lock error paths
selftests: ntsync: correct CONFIG_NTSYNC name
comedi: comedi_parport: deal with premature interrupt
uio_hv_generic: Bind to FCopy device by default
MAINTAINERS: Add Greg Kroah-Hartman to GPIB
firmware: stratix10-svc: fix teardown order in remove to prevent race
firmware: stratix10-svc: handle NO_RESPONSE in async poll
firmware: stratix10-svc: fix FCS SMC call kernel-doc
firmware: stratix10-svc: fix memory leaks and list corruption bugs
Here are two small staging driver fixes for 7.2-rc5. They both resolve
some reported bugs in the rtl8723bs staging driver and have been in
linux-next for over a week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCamYAxA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfoQCghy7Exq7vpWMlhR8LwQucWqABsxsAnjzK86WN
8VZ68CMngObWMPH31Dx7
=sWD7
-----END PGP SIGNATURE-----
Merge tag 'staging-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are two small staging driver fixes for 7.2-rc5. They both resolve
some reported bugs in the rtl8723bs staging driver and have been in
linux-next for over a week with no reported issues"
* tag 'staging-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8723bs: fix OOB reads in rtw_get_wps_ie()
staging: rtl8723bs: fix inverted HT40 secondary channel offset
Here are two small serial driver fixes for 7.2-rc5. They are:
- sc16is7xx get_direction() callback fix, which resolves a
user-triggerable warning in the driver
- NULL pointer dereference on some platforms using the 8250_mid serial
driver
Both have been in linux-next for over a week with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCamYBZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykMjACgpSS04QGbBIWmMHnxBWHnDT+Z8qoAn210DRbo
l5E84oG0BSJg1i9c3mnj
=WB87
-----END PGP SIGNATURE-----
Merge tag 'tty-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are two small serial driver fixes for 7.2-rc5. They are:
- sc16is7xx get_direction() callback fix, which resolves a
user-triggerable warning in the driver
- NULL pointer dereference on some platforms using the 8250_mid
serial driver
Both have been in linux-next for over a week with no reported issues"
* tag 'tty-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sc16is7xx: implement gpio get_direction() callback
serial: 8250_mid: Fix NULL function pointer dereference on DNV/ICX-D/SNR platforms
Here are some small USB fixes and new device quirks and ids for 7.2-rc5.
Included in here are:
- usb storage quirk added
- new usb serial device ids added
- usb-serial device name leak and other bug fixes
- small xhci driver fixes
- normal batch of typec driver fixes for reported issues
- usb-atm much-reported-by-syzbot fix for firmware download races
- sysfs BOS device removal race fix
- lots of usb gadget driver fixes for reported issues
- other small USB driver fixes for other reported problems.
All of these have been in linux-next this past week, many of them much
longer.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCamYE0A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk0twCdFi0ivPtWtEzmP7lUNRCzmyT3MvoAoI7o6lJm
E5+ID/c4mWfX/DjoPFhU
=uUBv
-----END PGP SIGNATURE-----
Merge tag 'usb-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes and new device quirks and ids:
- usb storage quirk added
- new usb serial device ids added
- usb-serial device name leak and other bug fixes
- small xhci driver fixes
- normal batch of typec driver fixes for reported issues
- usb-atm much-reported-by-syzbot fix for firmware download races
- sysfs BOS device removal race fix
- lots of usb gadget driver fixes for reported issues
- other small USB driver fixes for other reported problems
All of these have been in linux-next this past week, many of them much
longer"
* tag 'usb-7.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (30 commits)
usb: typec: ucsi: Correct teardown ordering in ucsi_init() error path
USB: serial: io_edgeport: cap received transmit credits
USB: serial: option: add TDTECH MT5710-CN
USB: serial: io_ti: reject oversized boot-mode firmware
USB: serial: mxuport: validate firmware header size
usb: atm: ueagle-atm: reject descriptors that confuse probe and disconnect
usb: typec: ucsi: yoga_c630: Remove redundant duplicate altmode handling
usb: typec: ucsi: Add duplicate detection to nvidia registration path
usb: typec: ucsi: Detect and skip duplicate altmodes from buggy firmware
usb: gadget: dummy_hcd: prevent fifo_req reuse during giveback
usb: chipidea: fix usage_count leak when autosuspend_delay is negative
usb: core: sysfs: add lock to bos_descriptors_read()
usb: musb: omap2430: Do not put borrowed of_node in probe
usb: core: port: Deattach Type-C connector on component unbind
USB: storage: add NO_ATA_1X quirk for Longmai USB Key
USB: serial: ftdi_sio: add support for E+H FXA291
USB: serial: keyspan_pda: fix data loss on receive throttling
usb: gadget: printer: fix infinite loop in printer_read()
usb: gadget: f_midi: cancel pending IN work before freeing the midi object
usb: gadget: udc: bdc: free IRQ and drain func_wake_notify before teardown
...
