Commit graph

752,023 commits

Author SHA1 Message Date
David Ahern
9fbb704c33 net/ipv6: Refactor gateway validation on route add
Move gateway validation code from ip6_route_info_create into
ip6_validate_gw. Code move plus adjustments to handle the potential
reset of dev and idev and to make checkpatch happy.

Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 11:28:38 -04:00
Florian Fainelli
484d802d0f net: systemport: Rewrite __bcm_sysport_tx_reclaim()
There is no need for complex checking between the last consumed index
and current consumed index, a simple subtraction will do.

This also eliminates the possibility of a permanent transmit queue stall
under the following conditions:

- one CPU bursts ring->size worth of traffic (up to 256 buffers), to the
  point where we run out of free descriptors, so we stop the transmit
  queue at the end of bcm_sysport_xmit()

- because of our locking, we have the transmit process disable
  interrupts which means we can be blocking the TX reclamation process

- when TX reclamation finally runs, we will be computing the difference
  between ring->c_index (last consumed index by SW) and what the HW
  reports through its register

- this register is masked with (ring->size - 1) = 0xff, which will lead
  to stripping the upper bits of the index (register is 16-bits wide)

- we will be computing last_tx_cn as 0, which means there is no work to
  be done, and we never wake-up the transmit queue, leaving it
  permanently disabled

A practical example is e.g: ring->c_index aka last_c_index = 12, we
pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12,
so last_tx_cn == 0, nothing happens.

Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 11:16:55 -04:00
David S. Miller
1ad2ff028f Merge branch 'macb-Introduce-phy-handle-DT-functionality'
Brad Mouring says:

====================
net: macb: Introduce phy-handle DT functionality

Consider the situation where a macb netdev is connected through
a phydev that sits on a mii bus other than the one provided to
this particular netdev. This situation is what this patchset aims
to accomplish through the existing phy-handle optional binding.

This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is precisely the
situation this patchset aims to solve, so it makes sense to introduce
the functionality to this driver (where the physical layout discussed
was encountered).

The devicetree snippet would look something like this:

...
   ethernet@feedf00d {
           ...
           phy-handle = <&phy0> // the first netdev is physically wired to phy0
           ...
           phy0: phy@0 {
                   ...
                   reg = <0x0> // MDIO address 0
                   ...
           }
           phy1: phy@1 {
                   ...
                   reg = <0x1> // MDIO address 1
                   ...
           }
           ...
   }

   ethernet@deadbeef {
           ...
           phy-handle = <&phy1> // tells the driver to use phy1 on the
                                // first mac's mdio bus (it's wired thusly)
           ...
   }
...

The work done to add the phy_node in the first place (dacdbb4dfc:
"net: macb: add fixed-link node support") will consume the
device_node (if found).

v2: Reorganization of mii probe/init functions, suggested by Andrew Lunn
v3: Moved some of the bus init code back into init (erroneously moved to probe)
    some style issues, and an unintialized variable warning addressed.
v4: Add Reviewed-by: tags
    Skip fallback code if phy-handle phandle is found
v5: Cleanup formatting issues
    Fix compile failure introduced in 1/4 "net: macb: Reorganize macb_mii
        bringup"
    Fix typo in "Documentation: macb: Document phy-handle binding"
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 11:14:34 -04:00
Brad Mouring
f3b249e652 Documentation: macb: Document phy-handle binding
Document the existence of the optional binding, directing to the
general ethernet document that describes this binding.

Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 11:14:33 -04:00
Brad Mouring
2105a5d3ac net: macb: Add phy-handle DT support
This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is useful for a phy
chip that has >1 phy in it, and two netdevs are using the same phy
chip (i.e. the second mac's phy lives on the first mac's MDIO bus)

The devicetree snippet would look something like this:

ethernet@feedf00d {
	...
	phy-handle = <&phy0> // the first netdev is physically wired to phy0
	...
	phy0: phy@0 {
		...
		reg = <0x0> // MDIO address 0
		...
	}
	phy1: phy@1 {
		...
		reg = <0x1> // MDIO address 1
		...
	}
...
}

ethernet@deadbeef {
	...
	phy-handle = <&phy1> // tells the driver to use phy1 on the
						 // first mac's mdio bus (it's wired thusly)
	...
}

The work done to add the phy_node in the first place (dacdbb4dfc:
"net: macb: add fixed-link node support") will consume the
device_node (if found).

Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 11:14:33 -04:00
Brad Mouring
cb732e9a26 net: macb: Remove redundant poll irq assignment
In phy_device's general probe, this device will already be set for
phy register polling, rendering this code redundant.

Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 11:14:33 -04:00
Brad Mouring
739de9a156 net: macb: Reorganize macb_mii bringup
The macb mii setup (mii_probe() and mii_init()) previously was
somewhat interspersed, likely a result of organic growth and hacking.

This change moves mii bus registration into mii_init and probing the
bus for devices into mii_probe.

Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 11:14:33 -04:00
Tom Herbert
2cc683e88c kcm: lock lower socket in kcm_attach
Need to lock lower socket in order to provide mutual exclusion
with kcm_unattach.

v2: Add Reported-by for syzbot

Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+ea75c0ffcd353d32515f064aaebefc5279e6161e@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 11:12:16 -04:00
Stephen Hemminger
2b221d20db doc: remove out of date links and info from packet mmap
The packet_mmap documentation had links to no longer existing web
sites; replace with other site which has similar example.

Support for packet mmap has been in mainline versions of libpcap
for several years.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 10:48:52 -04:00
Gustavo A. R. Silva
225b3dc92d USB: wusbcore: crypto: Remove VLA usage
In preparation to enabling -Wvla, remove VLA and replace it
with dynamic memory allocation instead.

The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
or a security flaw. Also, in general, as code evolves it is easy to
lose track of how big a VLA can get. Thus, we can end up having runtime
failures that are hard to debug.

Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621

Notice that in this particular case, an alternative to kzalloc is kcalloc,
in which case the code would look as follows instead:

iv = kcalloc(crypto_skcipher_ivsize(tfm_cbc), sizeof(*iv), GFP_KERNEL);

but if the data type of _iv_ never changes, or the type size is always one
byte, kzalloc is good enough.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:19 +01:00
Andy Shevchenko
7bb9aedac6 USB: host: sl811: Re-use DEFINE_SHOW_ATTRIBUTE() macro
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:19 +01:00
Mathias Nyman
0ee78c1014 xhci: Show what USB release number the xHC supports from protocol capablity
xhci driver displays the supported xHC USB revision in a message during
driver load:

"Host supports USB 3.1 Enhanced SuperSpeed"

Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts

Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:19 +01:00
Mathias Nyman
f5249461b5 xhci: Clear the host side toggle manually when endpoint is soft reset
Some devices use a clear endpoint halt request as a soft reset, even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side.

xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host
side toggle and sequence, and get it in sync with the device side.

This is a respin of a old patch that was reverted as it had a stale
endpoint context dequeue value which caused regression.
commit 27082e2654 ("xhci: Clear the host side toggle manually when
endpoint is 'soft reset'")

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:19 +01:00
Mathias Nyman
15febf5eed xhci: refactor xhci_urb_enqueue a bit with minor changes
make the local ep_state variable a pointer to the actual ring ep_state.
This allows us to read fresh ep_state values every time, will be useful
later.

Also move the streams check out from bulk only case. Even if only
bulk tranfers can use streams we shouldn't continue if those flags
are set. Main reason for this change is really code readability and
grouping functionality

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:18 +01:00
Mathias Nyman
a38fe33889 xhci: Don't always run the default stop endpoint command completion handler
The default stop endpoint completion handler will give back cancelled
URBs, and clean, or move past those canceller TRBs on the ring.

This is not always the preferred action.

If the stop endpoint command issuer is waiting for a completion
skip the default handler and just call the completion.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:18 +01:00
Mathias Nyman
a400efe455 xhci: zero usb device slot_id member when disabling and freeing a xhci slot
set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.

xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:18 +01:00
Lu Baolu
0c341910cb usb: xhci: Remove ep_trb from finish_td()
Function argument ep_trb for finish_td() isn't needed anymore.
Cleanup it.

Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:18 +01:00
Lu Baolu
5fee5a5afa usb: xhci: Remove ep_trb from xhci_cleanup_halted_endpoint()
Function argument ep_trb for xhci_cleanup_halted_endpoint() isn't
needed anymore. Cleanup it.

Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:18 +01:00
Dan Carpenter
29f653393e usb: xhci: Clean up error code in xhci_dbc_tty_register_device()
tty_port_register_device() returns error pointers on error, never NULL.
The IS_ERR_OR_NULL() function returns either 1 or 0 so it means we
return 1 on error instead of a proper error code.  The caller only
checks for zero vs non-zero so this doesn't affect runtime.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-16 15:40:18 +01:00
Marc Zyngier
6ef6386ef7 irqchip/gic-v3: Loudly complain about the use of IRQ_TYPE_NONE
There is a huge number of broken device trees out there. Just
grepping through the tree for the use of IRQ_TYPE_NONE in conjunction
with the GIC is scary.

People just don't realise that IRQ_TYPE_NONE just doesn't exist, and
you just get whatever junk was there before. So let's make them aware
of the issue.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2018-03-16 14:38:13 +00:00
Marc Zyngier
83a86fbb5b irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE
There is a huge number of broken device trees out there. Just
grepping through the tree for the use of IRQ_TYPE_NONE in conjunction
with the GIC is scary.

People just don't realise that IRQ_TYPE_NONE just doesn't exist, and
you just get whatever junk was there before. So let's make them aware
of the issue.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2018-03-16 14:35:17 +00:00
Mark Rutland
bbb6846864 perf/core: Clear sibling list of detached events
When perf_group_dettach() is called on a group leader, it updates each
sibling's group_leader field to point to that sibling, effectively
upgrading each siblnig to a group leader. After perf_group_detach has
completed, the caller may free the leader event.

We only remove siblings from the group leader's sibling_list when the
leader has a non-empty group_node. This was fine prior to commit:

  8343aae661 ("perf/core: Remove perf_event::group_entry")

... as the sibling's sibling_list would be empty. However, now that we
use the sibling_list field as both the list head and the list entry,
this leaves each sibling with a non-empty sibling list, including the
stale leader event.

If perf_group_detach() is subsequently called on a sibling, it will
appear to be a group leader, and we'll walk the sibling_list,
potentially dereferencing these stale events. In 0day testing, this has
been observed to result in kernel panics.

Let's avoid this by always removing siblings from the sibling list when
we promote them to leaders.

Fixes: 8343aae661 ("perf/core: Remove perf_event::group_entry")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: vincent.weaver@maine.edu
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: torvalds@linux-foundation.org
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: valery.cherepennikov@intel.com
Cc: linux-tip-commits@vger.kernel.org
Cc: eranian@google.com
Cc: acme@redhat.com
Cc: alexander.shishkin@linux.intel.com
Cc: davidcc@google.com
Cc: kan.liang@intel.com
Cc: Dmitry.Prohorov@intel.com
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/r/20180316131741.3svgr64yibc6vsid@lakrids.cambridge.arm.com
2018-03-16 15:34:24 +01:00
Peter Zijlstra
7eb709f295 perf: Fix sibling iteration
Mark noticed that the change to sibling_list changed some iteration
semantics; because previously we used group_list as list entry,
sibling events would always have an empty sibling_list.

But because we now use sibling_list for both list head and list entry,
siblings will report as having siblings.

Fix this with a custom for_each_sibling_event() iterator.

Fixes: 8343aae661 ("perf/core: Remove perf_event::group_entry")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: vincent.weaver@maine.edu
Cc: alexander.shishkin@linux.intel.com
Cc: torvalds@linux-foundation.org
Cc: alexey.budankov@linux.intel.com
Cc: valery.cherepennikov@intel.com
Cc: eranian@google.com
Cc: acme@redhat.com
Cc: linux-tip-commits@vger.kernel.org
Cc: davidcc@google.com
Cc: kan.liang@intel.com
Cc: Dmitry.Prohorov@intel.com
Cc: jolsa@redhat.com
Link: https://lkml.kernel.org/r/20180315170129.GX4043@hirez.programming.kicks-ass.net
2018-03-16 15:34:10 +01:00
Rajvi Jingar
fc804f65d4 x86/tsc: Convert ART in nanoseconds to TSC
Device drivers use get_device_system_crosststamp() to produce precise
system/device cross-timestamps. The PHC clock and ALSA interfaces, for
example, make the cross-timestamps available to user applications.  On
Intel platforms, get_device_system_crosststamp() requires a TSC value
derived from ART (Always Running Timer) to compute the monotonic raw and
realtime system timestamps.

Starting with Intel Goldmont platforms, the PCIe root complex supports the
PTM time sync protocol. PTM requires all timestamps to be in units of
nanoseconds. The Intel root complex hardware propagates system time derived
from ART in units of nanoseconds performing the conversion as follows:

     ART_NS = ART * 1e9 / <crystal frequency>

When user software requests a cross-timestamp, the system timestamps
(generally read from device registers) must be converted to TSC by the
driver software as follows:

    TSC = ART_NS * TSC_KHZ / 1e6

This is valid when CPU feature flag X86_FEATURE_TSC_KNOWN_FREQ is set
indicating that tsc_khz is derived from CPUID[15H]. Drivers should check
whether this flag is set before conversion to TSC is attempted.

Suggested-by: Christopher S. Hall <christopher.s.hall@intel.com>
Signed-off-by: Rajvi Jingar <rajvi.jingar@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Link: https://lkml.kernel.org/r/1520530116-4925-1-git-send-email-rajvi.jingar@intel.com
2018-03-16 15:14:35 +01:00
David S. Miller
e693be293f Merge branch 'vlan-untag-and-insert-fixes'
Toshiaki Makita says:

====================
Fix vlan untag and insertion for bridge and vlan with reorder_hdr off

As Brandon Carpenter reported[1], sending non-vlan-offloaded packets from
bridge devices ends up with corrupted packets. He narrowed down this problem
and found that the root cause is in skb_reorder_vlan_header().

While I was working on fixing this problem, I found that the function does
not work properly for double tagged packets with reorder_hdr off as well.

Patch 1 fixes these 2 problems in skb_reorder_vlan_header().

And it turned out that fixing skb_reorder_vlan_header() is not sufficient
to receive double tagged packets with reorder_hdr off while I was testing the
fix. Vlan tags got out of order when vlan devices with reorder_hdr disabled
were stacked. Patch 2 fixes this problem.

[1] https://www.spinics.net/lists/linux-ethernet-bridging/msg07039.html
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 10:03:48 -04:00
Toshiaki Makita
cbe7128c4b vlan: Fix out of order vlan headers with reorder header off
With reorder header off, received packets are untagged in skb_vlan_untag()
called from within __netif_receive_skb_core(), and later the tag will be
inserted back in vlan_do_receive().

This caused out of order vlan headers when we create a vlan device on top
of another vlan device, because vlan_do_receive() inserts a tag as the
outermost vlan tag. E.g. the outer tag is first removed in skb_vlan_untag()
and inserted back in vlan_do_receive(), then the inner tag is next removed
and inserted back as the outermost tag.

This patch fixes the behaviour by inserting the inner tag at the right
position.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 10:03:47 -04:00
Toshiaki Makita
4bbb3e0e82 net: Fix vlan untag for bridge and vlan_dev with reorder_hdr off
When we have a bridge with vlan_filtering on and a vlan device on top of
it, packets would be corrupted in skb_vlan_untag() called from
br_dev_xmit().

The problem sits in skb_reorder_vlan_header() used in skb_vlan_untag(),
which makes use of skb->mac_len. In this function mac_len is meant for
handling rx path with vlan devices with reorder_header disabled, but in
tx path mac_len is typically 0 and cannot be used, which is the problem
in this case.

The current code even does not properly handle rx path (skb_vlan_untag()
called from __netif_receive_skb_core()) with reorder_header off actually.

In rx path single tag case, it works as follows:

- Before skb_reorder_vlan_header()

 mac_header                                data
   v                                        v
   +-------------------+-------------+------+----
   |        ETH        |    VLAN     | ETH  |
   |       ADDRS       | TPID | TCI  | TYPE |
   +-------------------+-------------+------+----
   <-------- mac_len --------->
                       <------------->
                        to be removed

- After skb_reorder_vlan_header()

            mac_header                     data
                 v                          v
                 +-------------------+------+----
                 |        ETH        | ETH  |
                 |       ADDRS       | TYPE |
                 +-------------------+------+----
                 <-------- mac_len --------->

This is ok, but in rx double tag case, it corrupts packets:

- Before skb_reorder_vlan_header()

 mac_header                                              data
   v                                                      v
   +-------------------+-------------+-------------+------+----
   |        ETH        |    VLAN     |    VLAN     | ETH  |
   |       ADDRS       | TPID | TCI  | TPID | TCI  | TYPE |
   +-------------------+-------------+-------------+------+----
   <--------------- mac_len ---------------->
                                     <------------->
                                    should be removed
                       <--------------------------->
                         actually will be removed

- After skb_reorder_vlan_header()

            mac_header                                   data
                 v                                        v
                               +-------------------+------+----
                               |        ETH        | ETH  |
                               |       ADDRS       | TYPE |
                               +-------------------+------+----
                 <--------------- mac_len ---------------->

So, two of vlan tags are both removed while only inner one should be
removed and mac_header (and mac_len) is broken.

skb_vlan_untag() is meant for removing the vlan header at (skb->data - 2),
so use skb->data and skb->mac_header to calculate the right offset.

Reported-by: Brandon Carpenter <brandon.carpenter@cypherpath.com>
Fixes: a6e18ff111 ("vlan: Fix untag operations of stacked vlans with REORDER_HEADER off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 10:03:47 -04:00
Govindarajulu Varadarajan
ce3db6aade enic: drop IP proto check for vxlan tunnel delete
Commit d11790941d ("enic: Add vxlan offload support for IPv6 pkts")
added vxlan offload support for IPv6 pkts. Required change in
enic_udp_tunnel_del was not made. This creates a bug where once user
adds IPv6 tunnel, hw offload for that cannot be deleted.

This patch removes check for IP proto in tunnel delete path. Driver need
not check for IP proto since same UDP port cannot be used to create two
tunnels.

Fixes: d11790941d ("enic: Add vxlan offload support for IPv6 pkts")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 09:50:40 -04:00
David Sterba
093e037ca8 Revert "btrfs: use proper endianness accessors for super_copy"
This reverts commit 3c181c12c4.

The offending patch was merged in 4.16-rc4 and was promptly applied to
stable kernels 4.14.25 and 4.15.8.

The patch causes a corruption in several superblock items on big-endian
machines because of messed up endianity conversions. The damage is
manually repairable. A filesystem cannot be mounted again after it has
been unmounted once.

We do a full revert and not a fixup so stable can pick that patch ASAP.

Fixes: 3c181c12c4 ("btrfs: use proper endianness accessors for super_copy")
Link: https://lkml.kernel.org/r/1521139304@msgid.manchmal.in-ulm.de
CC: stable@vger.kernel.org # 4.14+
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Signed-off-by: David Sterba <dsterba@suse.com>
2018-03-16 14:49:44 +01:00
Colin Ian King
650b4eca47 rxrpc: remove redundant initialization of variable 'len'
The variable 'len' is being initialized with a value that is never
read and it is re-assigned later, hence the initialization is redundant
and can be removed.

Cleans up clang warning:
net/rxrpc/recvmsg.c:275:15: warning: Value stored to 'len' during its
initialization is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-16 09:48:39 -04:00
Ville Syrjälä
80343b3e47 drm/i915: Use drm_color_lut_size()
Avoid all the sizeof(drm_color_lut) business by using
drm_color_lut_size() to convert the blob length into
number of LUT entries.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-6-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2018-03-16 15:44:01 +02:00
Ville Syrjälä
d5517a39dc drm/i915: Remove the blob->data casts
Now that blob->data is void* again we don't need to cast it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-5-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2018-03-16 15:44:01 +02:00
Ville Syrjälä
41204dfeed drm: Introduce drm_color_lut_size()
Provide a small helper to convert the blob length in bytes
to the number of LUT entries.

v2: Add kerneldoc (Daniel)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315152338.7248-1-ville.syrjala@linux.intel.com
2018-03-16 15:44:01 +02:00
Ville Syrjälä
d2a24edb53 drm: Verify gamma/degamma LUT size
While we want to potentially support multiple different gamma/degamma
LUT sizes we can (and should) at least check that the blob length
is a multiple of the LUT entry size.

v2: s/expected_size_mod/expected_elem_size/ (Daniel)
    Add kernel doc (Daniel)
v3: s/we/were/ typo in the docs

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315152241.7113-1-ville.syrjala@linux.intel.com
2018-03-16 15:44:01 +02:00
Ville Syrjälä
11b83e3fbc drm: Remove now pointelss blob->data casts
Now that blob->data is void* again we don't need the casts anymore.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-2-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2018-03-16 15:44:01 +02:00
Ville Syrjälä
9c60583c0b Revert "drm: Use a flexible array member for blob property data"
Using a flexible array for the blob data was a mistake by me. It
forces all users of the blob data to cast blob->data to something
else. void* is clearly superior so let's go back to the original
scheme.

Not a clean revert as the code has moved.

This reverts commit d63f5e6bf6.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2018-03-16 15:44:01 +02:00
Tom Lendacky
daaf216c06 KVM: x86: Fix device passthrough when SME is active
When using device passthrough with SME active, the MMIO range that is
mapped for the device should not be mapped encrypted.  Add a check in
set_spte() to insure that a page is not mapped encrypted if that page
is a device MMIO page as indicated by kvm_is_mmio_pfn().

Cc: <stable@vger.kernel.org> # 4.14.x-
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-03-16 14:32:23 +01:00
Rafał Miłecki
1259055170 brcmfmac: drop Inter-Access Point Protocol packets by default
Testing brcmfmac with more recent firmwares resulted in AP interfaces
not working in some specific setups. Debugging resulted in discovering
support for IAPP in Broadcom's firmwares.

Older firmwares were only generating 802.11f frames. Newer ones like:
1) 10.10 (TOB) (r663589)
2) 10.10.122.20 (r683106)
for 4366b1 and 4366c0 respectively seem to also /respect/ 802.11f frames
in the Tx path by performing a STA disassociation.

This obsoleted standard and its implementation is something that:
1) Most people don't need / want to use
2) Can allow local DoS attacks
3) Breaks AP interfaces in some specific bridge setups

To solve issues it can cause this commit modifies brcmfmac to drop IAPP
packets. If affects:
1) Rx path: driver won't be sending these unwanted packets up.
2) Tx path: driver will reject packets that would trigger STA
   disassociation perfromed by a firmware (possible local DoS attack).

It appears there are some Broadcom's clients/users who care about this
feature despite the drawbacks. They can switch it on using a new module
param.

This change results in only two more comparisons (check for module param
and check for Ethernet packet length) for 99.9% of packets. Its overhead
should be very minimal.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-16 15:00:24 +02:00
Kalle Valo
1e2dce98c0 Third batch of iwlwifi fixes intended for 4.16:
* Fix an issue with the multicast queue;
 * Fix IGTK handling;
 * Fix some missing return value checks;
 * Add support for a HW workaround for issues on some platforms;
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAlqrnicACgkQoUecoho8
 xfpY8g//aktEH+rM6tt3mfdVAq8qVTPdTbE/foM0IQ1kb1zRAb1WMS1RskxLjVZk
 AD8RTpmb7Qp7j5OaNZ8f5jgE60G7GdecQqueZZvsVFla39U9MCwQD7ZGyr/lKdQt
 jVFC64lDHUyKdRybaelKaBU/oiRWd4/pIpL0Tb/Dtxx7akmLnr6c3WhiL7/fTned
 cuQ5TVzdTGvunZzUnTAPA8vf+C++BKdjdxpL6BS4cxsSvIt6oYnTUemEfwuPYKiz
 sQzBYhf4pbt3Yd7FAMdQnny3qBgQ1+avTheM9SAOeIUxSrTx5c6rnUFqh9rXFDMO
 vZDkxnvmlVS1fWqATcRaD/7vAEku9hcTs4rjxfvM116y/sw2oPdjYAZ8l9OIL4Mb
 Kfj29+mKc4vRS6Gtt2mRMxIQvM1XoUFk45fynmdWI16Mm/0dYJA+qYtw4i6SV1eG
 ZrvG+nikp/k6VmEeEbkBI28wQCYyGuDODTk83dbcrWFS49hvtNkd3mo5o4BDNKHC
 R8b0afvTZVmosgGOf43BdSs6Qi6K7cXZDWWnRs/+piaYx4RH+vAbGSLEumXYI/H2
 nSeYvBcXEWEOoY//mzQryhwxpgj2tSUDDn/nBw7WKqWoL4zJlsU4GYP32lDKID+B
 MxpMhYK7vouooDVY3US1CfXraZVqDolngwdtbSE79nS+ma8ovKA=
 =Vhr7
 -----END PGP SIGNATURE-----

Merge tag 'iwlwifi-for-kalle-2018-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Third batch of iwlwifi fixes intended for 4.16:

* Fix an issue with the multicast queue;
* Fix IGTK handling;
* Fix some missing return value checks;
* Add support for a HW workaround for issues on some platforms;
2018-03-16 14:39:55 +02:00
Tvrtko Ursulin
22de4e7a53 drm/i915/pmu: Work around compiler warnings on some kernel configs
Arnd Bergman reports:
"""
The conditional spinlock confuses gcc into thinking the 'flags' value
might contain uninitialized data:

drivers/gpu/drm/i915/i915_pmu.c: In function '__i915_pmu_event_read':
arch/x86/include/asm/paravirt_types.h:573:3: error: 'flags' may be used uninitialized in this function [-Werror=maybe-uninitialized]

The code is correct, but it's easy to see how the compiler gets confused
here. This avoids the problem by pulling the lock outside of the function
into its only caller.
"""

On deeper look it seems this is caused by paravirt spinlocks
implementation when CONFIG_PARAVIRT_DEBUG is set, which by being
complicated, manages to convince gcc locked parameter can be changed
externally (impossible).

Work around it by removing the conditional locking parameters altogether.
(It was never the most elegant code anyway.)

Slight penalty we now pay is an additional irqsave spin lock/unlock cycle
on the event enable path. But since enable is not a fast path, that is
preferrable to the alternative solution which was doing MMIO under irqsave
spinlock.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1fe699e301 ("drm/i915/pmu: Fix sleep under atomic in RC6 readout")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314080535.17490-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit ad055fb8e0)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2018-03-16 14:35:41 +02:00
Chris Wilson
73e2232aa3 drm/i915: Only call tasklet_kill() on the first prepare_reset
tasklet_kill() will spin waiting for the current tasklet to be executed.
However, if tasklet_disable() has been called, then the tasklet is never
executed but permanently put back onto the runlist until
tasklet_enable() is called. Ergo, we cannot use tasklet_kill() inside a
disable/enable pair. This is the case when we call set-wedge from inside
i915_reset(), and another request was submitted to us concurrent to the
reset.

Fixes: 963ddd63c3 ("drm/i915: Suspend submission tasklets around wedging")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-6-chris@chris-wilson.co.uk
(cherry picked from commit 68ad361285)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2018-03-16 14:35:35 +02:00
Chris Wilson
7e9d3a4a1b drm/i915: Wrap engine->schedule in RCU locks for set-wedge protection
Similar to the staging around handling of engine->submit_request, we
need to stop adding to the execlists->queue prior to calling
engine->cancel_requests. cancel_requests will move requests from the
queue onto the timeline, so if we add a request onto the queue after that
point, it will be lost.

Fixes: af7a8ffad9 ("drm/i915: Use rcu instead of stop_machine in set_wedged")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-5-chris@chris-wilson.co.uk
(cherry picked from commit 47650db02d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2018-03-16 14:35:31 +02:00
Jani Nikula
84d4ebdb6c drm/i915/icl: do not save DDI A/E sharing bit for ICL
We don't want to preserve the DDI A 4 lane bit on ICL.

Fixes: 3d2011cfa4 ("drm/i915/icl: remove port A/E lane sharing limitation.")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306104155.3526-1-jani.nikula@intel.com
(cherry picked from commit 1e6aa7e55c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2018-03-16 14:35:26 +02:00
Rob Herring
101646a24a microblaze: switch to NO_BOOTMEM
Microblaze doesn't set CONFIG_NO_BOOTMEM and so memblock_virt_alloc()
doesn't work for CONFIG_HAVE_MEMBLOCK && !CONFIG_NO_BOOTMEM.

Similar change was already done by others architectures
"ARM: mm: Remove bootmem code and switch to NO_BOOTMEM"
(sha1: 84f452b1e8)
or
"openrisc: Consolidate setup to use memblock instead of bootmem"
(sha1: 266c7fad15)
or
"parisc: Drop bootmem and switch to memblock"
(sha1: 4fe9e1d957)
or
"powerpc: Remove bootmem allocator"
(sha1: 10239733ee)
or
"s390/mm: Convert bootmem to memblock"
(sha1: 50be634507)
or
"sparc64: Convert over to NO_BOOTMEM."
(sha1: 625d693e97)
or
"xtensa: drop sysmem and switch to memblock"
(sha1: 0e46c1115f)

Issue was introduced by:
"of/fdt: use memblock_virt_alloc for early alloc"
(sha1: 0fa1c57934)

Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-16 12:51:27 +01:00
Rob Herring
cd4dfee6a8 microblaze: remove unused alloc_maybe_bootmem
alloc_maybe_bootmem is unused, so remove it.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-16 12:51:27 +01:00
Michal Simek
18ffc0cce4 microblaze: Setup dependencies for ASM optimized lib functions
The patch:
"microblaze: Setup proper dependency for optimized lib functions"
(sha1: 7b6ce52be3)
didn't setup all dependencies properly.
Optimized lib functions in C are also present for little endian
and optimized library functions in assembler are implemented only for
big endian version.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-16 12:51:26 +01:00
Alexander Sergeyev
e3b3121fa8 x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
In accordance with Intel's microcode revision guidance from March 6 MCU
rev 0xc2 is cleared on both Skylake H/S and Skylake Xeon E3 processors
that share CPUID 506E3.

Signed-off-by: Alexander Sergeyev <sergeev917@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jia Zhang <qianyue.zj@alibaba-inc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kyle Huey <me@kylehuey.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180313193856.GA8580@localhost.localdomain
2018-03-16 12:33:11 +01:00
Thierry Reding
e7f4da4c44 phy: tegra: xusb: Uncomment register write
The reason why this was originally commented out is no longer clear. The
UPHY driver for SATA works fine with or without this change. The reset
value of the XDIGCLK_EN bit is 0, so unless programmed by the bootloader
this shouldn't make a difference anyway.

Define a macro for this bit and uncomment the code. This also fixes a
coverity issue brought to my attention by Rohith because not only is the
XDIGCLK_EN field modification commented out, but also the register write
which causes none of the earlier modifications of the register value to
be written to the register and the value being overwritten.

Reported-by: Rohith Seelaboyina <rseelaboyina@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:38 +05:30
Enric Balletbo i Serra
ec1fcd7b7e phy: rockchip-typec: fall back to working in host-mode if extcon is missing.
Right now the rockchip type-c phy does fail probing when no extcon is
detected. Some boards get the cable-state via the extcon interface and
have this supported, other boards seem to use the fusb302 chip or
another but the driver currently does not seem to utilize the extcon
interface to report the cable-state. And, other, just connect the type-c
to a standard USB-A port so use no controller at all. A missing extcon
shouldn't fail to probe, instead, should just fall back to working in
host-mode if it cannot get the extcon.

Fixes: c301b327ae ("arm64: dts: rockchip: add usb3-phy otg-port support for rk3399")
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:37 +05:30
Enric Balletbo i Serra
21bf9bc2a9 dt-bindings: phy-rockchip-typec: move extcon property to be optional.
The extcon property is used to detect the cable-state but some boards
just connect the type-c phy to a regular USB-A connector without any
power-delivery and thus no controller reporting the cable-state.
So the extcon property is not really a required property, move it to be
optional instead.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:36 +05:30